Flying-capacitor-based chopper circuit for DC capacitor voltage balancing in diode-clamped multilevel inverter

This paper proposes a flying-capacitor-based chopper circuit for dc capacitor voltage equalization in diode-clamped multilevel inverters. Its important features are reduced voltage stress across the chopper switches, possible reduction in the chopper switching frequency, improved reliability, and ride-through capability enhancement. This topology is analyzed using three- and four-level flying-capacitor-based chopper circuit configurations. These configurations are different in capacitor and semiconductor device count and correspondingly reduce the device voltage stresses by half and one-third, respectively. The detailed working principles and control schemes for these circuits are presented. It is shown that, by preferentially selecting the available chopper switch states, the dc-link capacitor voltages can be efficiently equalized in addition to having tightly regulated flying-capacitor voltages around their references. The various operating modes of the chopper are described along with their preferential selection logic to achieve the desired performances. The performance of the proposed chopper and corresponding control schemes are confirmed through both simulation and experimental investigations.

Description and evaluation of a Newton-based electronic appetite rating system for temporal tracking of appetite in human subjects

This study assessed the reliability and validity of a palm-top-based electronic appetite rating system (EARS) in relation to the traditional paper and pen method. Twenty healthy subjects [10 male (M) and 10 female (F)] — mean age M=31 years (S.D.=8), F=27 years (S.D.=5); mean BMI M=24 (S.D.=2), F=21 (S.D.=5) — participated in a 4-day protocol. Measurements were made on days 1 and 4. Subjects were given paper and an EARS to log hourly subjective motivation to eat during waking hours. Food intake and meal times were fixed. Subjects were given a maintenance diet (comprising 40% fat, 47% carbohydrate and 13% protein by energy) calculated at 1.6×Resting Metabolic Rate (RMR), as three isoenergetic meals. Bland and Altman's test for bias between two measurement techniques found significant differences between EARS and paper and pen for two of eight responses (hunger and fullness). Regression analysis confirmed that there were no day, sex or order effects between ratings obtained using either technique. For 15 subjects, there was no significant difference between results, with a linear relationship between the two methods that explained most of the variance (r2 ranged from 62.6 to 98.6). The slope for all subjects was less than 1, which was partly explained by a tendency for bias at the extreme end of results on the EARS technique. These data suggest that the EARS is a useful and reliable technique for real-time data collection in appetite research but that it should not be used interchangeably with paper and pen techniques.

A novel technique to demonstrate disturbed appetite profiles in haemodialysis patients

Background Malnutrition is common among dialysis patients and is associated with an adverse outcome. One cause of this is a persistent reduction in nutrient intake, suggesting an abnormality of appetite regulation. Methods We used a novel technique to describe the appetite profile in 46 haemodialysis (HD) patients and 40 healthy controls. The Electronic Appetite Rating System (EARS) employs a palmtop computer to collect hourly ratings of motivation to eat and mood. We collected data on hunger, desire to eat, fullness, and tiredness. HD subjects were monitored on the dialysis day and the interdialytic day. Controls were monitored for 1 or 2 days. Results Temporal profiles of motivation to eat for the controls were similar on both days. Temporal profiles of motivation to eat for the HD group were lower on the dialysis day. Mean HD scores were not significantly different from controls. Dietary records indicated that dialysis patients consumed less food than controls. Conclusions Our data indicate that the EARS can be used to monitor subjective appetite states continuously in a group of HD patients. A HD session reduces hunger and desire to eat. Patients feel more tired after dialysis. This does not correlate with their hunger score, but does correlate with their fullness rating. Nutrient intake is reduced, suggesting a resetting of appetite control for the HD group. The EARS may be useful for intervention studies.

Exercise, appetite, and energy balance: The interactions between energy expenditure and intake, and the implications for weight management

This book disseminates current information pertaining to the modulatory effects of foods and other food substances on behavior and neurological pathways and, importantly, vice versa. This ranges from the neuroendocrine control of eating to the effects of life-threatening disease on eating behavior. The importance of this contribution to the scientific literature lies in the fact that food and eating are an essential component of cultural heritage but the effects of perturbations in the food/cognitive axis can be profound. The complex interrelationship between neuropsychological processing, diet, and behavioral outcome is explored within the context of the most contemporary psychobiological research in the area. This comprehensive psychobiology- and pathology-themed text examines the broad spectrum of diet, behavioral, and neuropsychological interactions from normative function to occurrences of severe and enduring psychopathological processes

Selective effects of acute exercise and breakfast interventions on mood and motivation to eat

The effects of exercise and breakfast manipulations on mood and motivation to eat were assessed in 11 healthy females who were regular exercisers and habitual breakfast eaters. The study involved a two by two repeated-measures design, with exercise (or no exercise) and a high-energy breakfast (or low-energy breakfast) as the repeated measures. The exercise or no-exercise session (0800 h) was followed by consumption of the low- or high-energy breakfast (0900 h). An ad libitum lunch test meal was provided 4 hours after the beginning of the exercise session (1200 h). Mood and motivation to eat were continuously tracked from 0800 until 1700 h by an electronic appetite ratings system (EARS). In general, morning subjective mood states (e.g., contentment) were significantly lower in the low-energy breakfast condition, but exercise reversed this effect. Exercise also significantly decreased feelings of lethargy, independent of the breakfast condition. Desire-to-eat and fullness ratings were significantly increased in the low-energy breakfast and high-energy breakfast conditions, respectively. Impairments of mood disappeared in the afternoon after consumption of an ad libitum lunch. In these healthy young adults, the condition inducing the largest energy deficit (exercise and low-energy breakfast) was not associated with the lowest mental states.

The patentability of non-physical inventions : lessons from the United States

Patent systems around the world are being pressed to recognise and protect challengingly new and exciting subject matter in order to keep pace with the rapid technological advancement of our age and the fact we are moving into the era of the ‘knowledge economy’. This rapid development and pressure to expand the bounds of what has traditionally been recognised as patentable subject matter has created uncertainty regarding what it is that the patent system is actually supposed to protect. Among other things, the patent system has had to contend with uncertainty surrounding claims to horticultural and agricultural methods, artificial living micro-organisms, methods of treating the human body, computer software and business methods. The contentious issue of the moment is one at whose heart lies the important distinction between what is a mere abstract idea and what is properly an invention deserving of the monopoly protection afforded by a patent. That question is whether purely intangible inventions, being methods that do not involve a physical aspect or effect or cause a physical transformation of matter, constitute patentable subject matter. This paper goes some way to addressing these uncertainties by considering how the Australian approach to the question can be informed by developments arising in the United States of America, and canvassing some of the possible lessons we in Australia might learn from the approaches taken thus far in the United States.

Multilevel converter structure and control

In recent years, multilevel converters are becoming more popular and attractive than traditional converters in high voltage and high power applications. Multilevel converters are particularly suitable for harmonic reduction in high power applications where semiconductor devices are not able to operate at high switching frequencies or in high voltage applications where multilevel converters reduce the need to connect devices in series to achieve high switch voltage ratings. This thesis investigated two aspects of multilevel converters: structure and control. The first part of this thesis focuses on inductance between a DC supply and inverter components in order to minimise loop inductance, which causes overvoltages and stored energy losses during switching. Three dimensional finite element simulations and experimental tests have been carried out for all sections to verify theoretical developments. The major contributions of this section of the thesis are as follows: The use of a large area thin conductor sheet with a rectangular cross section separated by dielectric sheets (planar busbar) instead of circular cross section wires, contributes to a reduction of the stray inductance. A number of approximate equations exist for calculating the inductance of a rectangular conductor but an assumption was made that the current density was uniform throughout the conductors. This assumption is not valid for an inverter with a point injection of current. A mathematical analysis of a planar bus bar has been performed at low and high frequencies and the inductance and the resistance values between the two points of the planar busbar have been determined. A new physical structure for a voltage source inverter with symmetrical planar bus bar structure called Reduced Layer Planar Bus bar, is proposed in this thesis based on the current point injection theory. This new type of planar busbar minimises the variation in stray inductance for different switching states. The reduced layer planar busbar is a new innovation in planar busbars for high power inverters with minimum separation between busbars, optimum stray inductance and improved thermal performances. This type of the planar busbar is suitable for high power inverters, where the voltage source is supported by several capacitors in parallel in order to provide a low ripple DC voltage during operation. A two layer planar busbar with different materials has been analysed theoretically in order to determine the resistance of bus bars during switching. Increasing the resistance of the planar busbar can gain a damping ratio between stray inductance and capacitance and affects the performance of current loop during switching. The aim of this section is to increase the resistance of the planar bus bar at high frequencies (during switching) and without significantly increasing the planar busbar resistance at low frequency (50 Hz) using the skin effect. This contribution shows a novel structure of busbar suitable for high power applications where high resistance is required at switching times. In multilevel converters there are different loop inductances between busbars and power switches associated with different switching states. The aim of this research is to consider all combinations of the switching states for each multilevel converter topology and identify the loop inductance for each switching state. Results show that the physical layout of the busbars is very important for minimisation of the loop inductance at each switch state. Novel symmetrical busbar structures are proposed for multilevel converters with diode-clamp and flying-capacitor topologies which minimise the worst case in stray inductance for different switching states. Overshoot voltages and thermal problems are considered for each topology to optimise the planar busbar structure. In the second part of the thesis, closed loop current techniques have been investigated for single and three phase multilevel converters. The aims of this section are to investigate and propose suitable current controllers such as hysteresis and predictive techniques for multilevel converters with low harmonic distortion and switching losses. This section of the thesis can be classified into three parts as follows: An optimum space vector modulation technique for a three-phase voltage source inverter based on a minimum-loss strategy is proposed. One of the degrees of freedom for optimisation of the space vector modulation is the selection of the zero vectors in the switching sequence. This new method improves switching transitions per cycle for a given level of distortion as the zero vector does not alternate between each sector. The harmonic spectrum and weighted total harmonic distortion for these strategies are compared and results show up to 7% weighted total harmonic distortion improvement over the previous minimum-loss strategy. The concept of SVM technique is a very convenient representation of a set of three-phase voltages or currents used for current control techniques. A new hysteresis current control technique for a single-phase multilevel converter with flying-capacitor topology is developed. This technique is based on magnitude and time errors to optimise the level change of converter output voltage. This method also considers how to improve unbalanced voltages of capacitors using voltage vectors in order to minimise switching losses. Logic controls require handling a large number of switches and a Programmable Logic Device (PLD) is a natural implementation for state transition description. The simulation and experimental results describe and verify the current control technique for the converter. A novel predictive current control technique is proposed for a three-phase multilevel converter, which controls the capacitors' voltage and load current with minimum current ripple and switching losses. The advantage of this contribution is that the technique can be applied to more voltage levels without significantly changing the control circuit. The three-phase five-level inverter with a pure inductive load has been implemented to track three-phase reference currents using analogue circuits and a programmable logic device.

The impact of brand and product placements in electronic games

In an environment where it has become increasingly difficult to attract consumer attention, marketers have begun to explore alternative forms of marketing communication. One such form that has emerged is product placement, which has more recently appeared in electronic games. Given changes in media consumption and the growth of the games industry, it is not surprising that games are being exploited as a medium for promotional content. Other market developments are also facilitating and encouraging their use, in terms of both the insertion of brand messages into video games and the creation of brand-centred environments, labelled ‘advergames’. However, while there is much speculation concerning the beneficial outcomes for marketers, there remains a lack of academic work in this area and little empirical evidence of the actual effects of this form of promotion on game players. Only a handful of studies are evident in the literature, which have explored the influence of game placements on consumers. The majority have studied their effect on brand awareness, largely demonstrating that players can recall placed brands. Further, most research conducted to date has focused on computer and online games, but consoles represent the dominant platform for play (Taub, 2004). Finally, advergames have largely been neglected, particularly those in a console format. Widening the gap in the literature is the fact that insufficient academic attention has been given to product placement as a marketing communication strategy overall, and to games in general. The unique nature of the strategy also makes it difficult to apply existing literature to this context. To address a significant need for information in both the academic and business domains, the current research investigates the effects of brand and product placements in video games and advergames on consumer attitude to the brand and corporate image. It was conducted in two stages. Stage one represents a pilot study. It explored the effects of use simulated and peripheral placements in video games on players’ and observers’ attitudinal responses, and whether these are influenced by involvement with a product category or skill level in the game. The ability of gamers to recall placed brands was also examined. A laboratory experiment was employed with a small sample of sixty adult subjects drawn from an Australian east-coast university, some of who were exposed to a console video game on a television set. The major finding of study one is that placements in a video game have no effect on gamers’ attitudes, but they are recalled. For stage two of the research, a field experiment was conducted with a large, random sample of 350 student respondents to investigate the effects on players of brand and product placements in handheld video games and advergames. The constructs of brand attitude and corporate image were again tested, along with several potential confounds. Consistent with the pilot, the results demonstrate that product placement in electronic games has no effect on players’ brand attitudes or corporate image, even when allowing for their involvement with the product category, skill level in the game, or skill level in relation to the medium. Age and gender also have no impact. However, the more interactive a player perceives the game to be, the higher their attitude to the placed brand and corporate image of the brand manufacturer. In other words, when controlling for perceived interactivity, players experienced more favourable attitudes, but the effect was so weak it probably lacks practical significance. It is suggested that this result can be explained by the existence of excitation transfer, rather than any processing of placed brands. The current research provides strong, empirical evidence that brand and product placements in games do not produce strong attitudinal responses. It appears that the nature of the game medium, game playing experience and product placement impose constraints on gamer motivation, opportunity and ability to process these messages, thereby precluding their impact on attitude to the brand and corporate image. Since this is the first study to investigate the ability of video game and advergame placements to facilitate these deeper consumer responses, further research across different contexts is warranted. Nevertheless, the findings have important theoretical and managerial implications. This investigation makes a number of valuable contributions. First, it is relevant to current marketing practice and presents findings that can help guide promotional strategy decisions. It also presents a comprehensive review of the games industry and associated activities in the marketplace, relevant for marketing practitioners. Theoretically, it contributes new knowledge concerning product placement, including how it should be defined, its classification within the existing communications framework, its dimensions and effects. This is extended to include brand-centred entertainment. The thesis also presents the most comprehensive analysis available in the literature of how placements appear in games. In the consumer behaviour discipline, the research builds on theory concerning attitude formation, through application of MacInnis and Jaworski’s (1989) Integrative Attitude Formation Model. With regards to the games literature, the thesis provides a structured framework for the comparison of games with different media types; it advances understanding of the game medium, its characteristics and the game playing experience; and provides insight into console and handheld games specifically, as well as interactive environments generally. This study is the first to test the effects of interactivity in a game environment, and presents a modified scale that can be used as part of future research. Methodologically, it addresses the limitations of prior research through execution of a field experiment and observation with a large sample, making this the largest study of product placement in games available in the literature. Finally, the current thesis offers comprehensive recommendations that will provide structure and direction for future study in this important field.