Redundant sensing for localisation in outdoor industrial environments

We describe our experiences with automating a large fork-lift type vehicle that operates outdoors and in all weather. In particular, we focus on the use of independent and robust localisation systems for reliable navigation around the worksite. Two localisation systems are briefly described. The first is based on laser range finders and retro-reflective beacons, and the second uses a two camera vision system to estimate the vehicle’s pose relative to a known model of the surrounding buildings. We show the results from an experiment where the 20 tonne experimental vehicle, an autonomous Hot Metal Carrier, was conducting autonomous operations and one of the localisation systems was deliberately made to fail.

Autonomous hot metal carrier: Navigation and manipulation with a 20 tonne industrial vehicle

This paper reports work on the automation of a hot metal carrier, which is a 20 tonne forklift-type vehicle used to move molten metal in aluminium smelters. To achieve efficient vehicle operation, issues of autonomous navigation and materials handling must be addressed. We present our complete system and experiments demonstrating reliable operation. One of the most significant experiments was five-hours of continuous operation where the vehicle travelled over 8 km and conducted 60 load handling operations. Finally, an experiment where the vehicle and autonomous operation were supervised from the other side of the world via a satellite phone network are described.

Catalytic activity evaluation of industrial Pd/C catalyst via gray-box dynamic modeling and simulation of hydropurification reactor

In this paper, dynamic modeling and simulation of the hydropurification reactor in a purified terephthalic acid production plant has been investigated by gray-box technique to evaluate the catalytic activity of palladium supported on carbon (0.5 wt.% Pd/C) catalyst. The reaction kinetics and catalyst deactivation trend have been modeled by employing artificial neural network (ANN). The network output has been incorporated with the reactor first principle model (FPM). The simulation results reveal that the gray-box model (FPM and ANN) is about 32 percent more accurate than FPM. The model demonstrates that the catalyst is deactivated after eleven months. Moreover, the catalyst lifetime decreases about two and half months in case of 7 percent increase of reactor feed flowrate. It is predicted that 10 percent enhancement of hydrogen flowrate promotes catalyst lifetime at the amount of one month. Additionally, the enhancement of 4-carboxybenzaldehyde concentration in the reactor feed improves CO and benzoic acid synthesis. CO is a poison to the catalyst, and benzoic acid might affect the product quality. The model can be applied into actual working plants to analyze the Pd/C catalyst efficient functioning and the catalytic reactor performance.

Destined to design? How and why Australian women choose to study industrial design

Despite over three decades of legislation and initiatives designed to tackle the traditional gender divide in the science, technology and design fields, only a quarter of the registered architects in Australia are women. There are no statistics available for other design disciplines, with little known about why women choose design as a career path and who or what influences this decision. This qualitative research addresses this knowledge gap, through semi-structured in-depth interviews conducted with 19 Australian women who completed an industrial (product) design degree. Thematic analysis revealed three key themes: childhood aptitude and exposure; significant experiences and people; and design as a serendipitous choice. The findings emphasise the importance of early exposure to design as a potential career choice, highlighting the critical role played by parents, teachers, professionals and social networks.

Studying industrial design : Exploring the experience of female students

Despite a significant increase in the number of women enrolling and graduating from design courses, the reality is that women remain ‘invisible’ in the design profession (Bruce, 1985). Over two decades ago, Bruce and Lewis (1990) argued that women were less likely than men to be designers due to three key gendered hurdles: the completion of a design degree, getting a design job and obtaining success in a design job. This paper focuses specifically on Australian women’s experience of hurdle one: the completion of a design degree, utilising industrial design as a case study. Semi-structured interview questions (exploring issues such as experience in class and the workshop, accessibility of the course and content, types of projects etc) were recorded and transcribed verbatim, with a thematic analysis conducted to better understand women’s experiences in completing their industrial design degree. This paper focuses on one key theme “navigating the design studio”, which comprises of three sub-themes: design skill development, the workshop experience and course evaluation. These findings highlight the need to understand the educational experience to ensure female designers remain motivated and eventually employable.

Industrial Designer

A discussion with Dr Rafael Gomez on Industrial Design for the Nelson Senior Graphics for Queensland Schools publication.

Bioaerosols associated with industrial green waste composting facilities and optimal microbiological indicators

This project developed and assessed a standard operating procedure for monitoring microbiological aerosol levels and dispersal from Australian industrial composting facilities. Development occurred via seasonal monitoring of such operations with evaluation of optimal microbial indicator organisms, sampling and analysis logistics. The resultant procedure allows practical end-user assessment of compost-associated bioaerosol levels, and potential health risks to proximal residential populations encroaching on such composting facilities and on-site industrial operations personnel.

Experiments and experiences with dependability for a large autonomous industrial vehicle

This paper describes the experiences gained performing multiple experiments while developing a large autonomous industrial vehicle. Hot Metal Carriers (HMCs) are large forklift-type vehicles used in the light metals industry to move molten or hot metal around a smelter. Autonomous vehicles of this type must be dependable as they are large and potentially hazardous to infrastructure and people. This paper will talk about four aspects of dependability, that of safety, reliability, availability and security and how they have been addressed on our experimental autonomous HMC.

Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

Applying digital product memories in industrial production

Industrial production and supply chains face increased demands for mass customization and tightening regulations on the traceability of goods, leading to higher requirements concerning flexibility, adaptability, and transparency of processes. Technologies for the ’Internet of Things' such as smart products and semantic representations pave the way for future factories and supply chains to fulfill these challenging market demands. In this chapter a backend-independent approach for information exchange in open-loop production processes based on Digital Product Memories DPMs is presented. By storing order-related data directly on the item, relevant lifecycle information is attached to the product itself. In this way, information handover between several stages of the value chain with focus on the manufacturing phase of a product has been realized. In order to report best practices regarding the application of DPM in the domain of industrial production, system prototype implementations focusing on the use case of producing and handling a smart drug case are illustrated.

Wastewater pollution abatement in China: A comparative study of fifteen industrial sectors from 1998 to 2010

This study analyzes the management of wastewater pollutants in a number of Chinese industrial sectors from 1998 to 2010. We use decomposition analysis to calculate changes in wastewater pollutant emissions that result from cleaner production processes, end-of-pipe treatment, structural changes in industry, and changes in the scale of production. We focus on one indicator of water quality and three pollutants: chemical oxygen demand (COD), petroleum, cyanide, and volatile phenols. We find that until 2002, COD emissions were mainly reduced through end-of-pipe treatments. Cleaner production processes didn’t begin contributing to COD emissions reductions until the introduction of a 2003 law that enforced their implementation. Petroleum emissions were primarily lowered through cleaner production mechanisms, which have the added benefit of reducing the input cost of intermediate petroleum. Diverse and effective pollution abatement strategies for cyanide and volatile phenols are emerging among industries in China. It will be important for the government to consider differences between industries should they choose to regulate the emissions of specific chemical substances.

Water use and wastewater discharge of industrial sector in China

Problem of water scarcity has been increasingly severe in China. Though industrial sectors play important role for the rapid economic growth, and they consumes water and discharge wastewater. The purpose of this study is to examine the efficiency of water use and wastewater discharge in comparison with those of other inputs and production output in Chinese industry. Measuring efficiency of each input and output factor from 2002 to 2008, we find the average inefficiencies of industrial water use and industrial wastewater discharge are higher than those of capital, labor, and production output in China. In addition, the productivity levels to save water in the water shortage areas are not higher compared to the others. The water use inefficiency has a high dispersion especially in the regions where the amounts of water resources per capita is less than 3000 cubic meter.

A novel experimental method to assess industrial aerosol deposition in idealized porous channels

A novel and economical experimental technique has been developed to assess industrial aerosol deposition in various idealized porous channel configurations. This judicious examination on aerosol penetration in porous channels will assist engineers to better optimize designs for various engineering applications. Deposition patterns differ with porosity due to geometric configurations of the channel and superficial inlet velocities. Interestingly, it is found that two configurations of similar porosity exhibit significantly higher deposition fractions. Inertial impaction is profound at the leading edge of all obstacles, whereas particle build-up is observed at the trailing edge of the obstructions. A qualitative analysis shows that the numerical results are in good agreement with experimental results.

Biofuels from food processing wastes

Food processing industry generates substantial high organic wastes along with high energy uses. The recovery of food processing wastes as renewable energy sources represents a sustainable option for the substitution of fossil energy, contributing to the transition of food sector towards a low-carbon economy. This article reviews the latest research progress on biofuel production using food processing wastes. While extensive work on laboratory and pilot-scale biosystems for energy production has been reported, this work presents a review of advances in metabolic pathways, key technical issues and bioengineering outcomes in biofuel production from food processing wastes. Research challenges and further prospects associated with the knowledge advances and technology development of biofuel production are discussed.

The ghost in the city industrial complex: Le Corbusier and the fascist theory of Urbanisme

Le Corbusier participated in an urban dialogue with the first group in France to call itself fascist: the journalist Georges Valois’s militant Faisceau des Combattants et Producteurs (1925-1927), the “Blue Shirts,” inspired by the Italian “Fasci” of Mussolini. Le Corbusier’s portrait photograph materialised on the front cover of the January 1927 issue of the Faisceau League’s newspaper Le Nouveau Siècle edited by the former anarcho-syndicalist journalist Georges Valois, its leader, who fashioned himself as the French Mussolini. Le Corbusier was described in the Revue as one of les animateurs (the “organisers”) of the Party1 – meaning a member of the technical elite who would drive the Faisceau’s plans. On 1 May 1927, the Nouveau Siècle printed a full-page feature “Le Plan Voisin” on Le Corbusier’s 1922 redesign of Paris : the architect’s single-point perspective sketch appeared below an extract lifted from the architect’s original polemic Le Centre de Paris on the pages of Le Corbusier’s second book Urbanisme published two years earlier, a treatise on urbanism.2 Three weeks later, Le Corbusier presented a slide show of his urban plans at a fascist rally for the inauguration of the Faisceau’s new headquarters on the rue du faubourg Poissonniere, thereby crystalising the architect’s hallowed status in the league...