Effect of pedestrian movement on MIMO-OFDM channel capacity in an indoor environment

The rapid growth of mobile telephone use, satellite services, and now the wireless Internet and WLANs are generating tremendous changes in telecommunication and networking. As indoor wireless communications become more prevalent, modeling indoor radio wave propagation in populated environments is a topic of significant interest. Wireless MIMO communication exploits phenomena such as multipath propagation to increase data throughput and range, or reduce bit error rates, rather than attempting to eliminate effects of multipath propagation as traditional SISO communication systems seek to do. The MIMO approach can yield significant gains for both link and network capacities, with no additional transmitting power or bandwidth consumption when compared to conventional single-array diversity methods. When MIMO and OFDM systems are combined and deployed in a suitable rich scattering environment such as indoors, a significant capacity gain can be observed due to the assurance of multipath propagation. Channel variations can occur as a result of movement of personnel, industrial machinery, vehicles and other equipment moving within the indoor environment. The time-varying effects on the propagation channel in populated indoor environments depend on the different pedestrian traffic conditions and the particular type of environment considered. A systematic measurement campaign to study pedestrian movement effects in indoor MIMO-OFDM channels has not yet been fully undertaken. Measuring channel variations caused by the relative positioning of pedestrians is essential in the study of indoor MIMO-OFDM broadband wireless networks. Theoretically, due to high multipath scattering, an increase in MIMO-OFDM channel capacity is expected when pedestrians are present. However, measurements indicate that some reductions in channel capacity could be observed as the number of pedestrians approaches 10 due to a reduction in multipath conditions as more human bodies absorb the wireless signals. This dissertation presents a systematic characterization of the effects of pedestrians in indoor MIMO-OFDM channels. Measurement results, using the MIMO-OFDM channel sounder developed at the CSIRO ICT Centre, have been validated by a customized Geometric Optics-based ray tracing simulation. Based on measured and simulated MIMO-OFDM channel capacity and MIMO-OFDM capacity dynamic range, an improved deterministic model for MIMO-OFDM channels in indoor populated environments is presented. The model can be used for the design and analysis of future WLAN to be deployed in indoor environments. The results obtained show that, in both Fixed SNR and Fixed Tx for deterministic condition, the channel capacity dynamic range rose with the number of pedestrians as well as with the number of antenna combinations. In random scenarios with 10 pedestrians, an increment in channel capacity of up to 0.89 bits/sec/Hz in Fixed SNR and up to 1.52 bits/sec/Hz in Fixed Tx has been recorded compared to the one pedestrian scenario. In addition, from the results a maximum increase in average channel capacity of 49% has been measured while 4 antenna elements are used, compared with 2 antenna elements. The highest measured average capacity, 11.75 bits/sec/Hz, corresponds to the 4x4 array with 10 pedestrians moving randomly. Moreover, Additionally, the spread between the highest and lowest value of the the dynamic range is larger for Fixed Tx, predicted 5.5 bits/sec/Hz and measured 1.5 bits/sec/Hz, in comparison with Fixed SNR criteria, predicted 1.5 bits/sec/Hz and measured 0.7 bits/sec/Hz. This has been confirmed by both measurements and simulations ranging from 1 to 5, 7 and 10 pedestrians.

Derivation of motor vehicle tailpipe particle emission factors suitable for modelling urban fleet emissions and air quality assessments

Background, aim, and scope Urban motor vehicle fleets are a major source of particulate matter pollution, especially of ultrafine particles (diameters < 0.1 µm), and exposure to particulate matter has known serious health effects. A considerable body of literature is available on vehicle particle emission factors derived using a wide range of different measurement methods for different particle sizes, conducted in different parts of the world. Therefore the choice as to which are the most suitable particle emission factors to use in transport modelling and health impact assessments presented as a very difficult task. The aim of this study was to derive a comprehensive set of tailpipe particle emission factors for different vehicle and road type combinations, covering the full size range of particles emitted, which are suitable for modelling urban fleet emissions. Materials and methods A large body of data available in the international literature on particle emission factors for motor vehicles derived from measurement studies was compiled and subjected to advanced statistical analysis, to determine the most suitable emission factors to use in modelling urban fleet emissions. Results This analysis resulted in the development of five statistical models which explained 86%, 93%, 87%, 65% and 47% of the variation in published emission factors for particle number, particle volume, PM1, PM2.5 and PM10 respectively. A sixth model for total particle mass was proposed but no significant explanatory variables were identified in the analysis. From the outputs of these statistical models, the most suitable particle emission factors were selected. This selection was based on examination of the statistical robustness of the statistical model outputs, including consideration of conservative average particle emission factors with the lowest standard errors, narrowest 95% confidence intervals and largest sample sizes, and the explanatory model variables, which were Vehicle Type (all particle metrics), Instrumentation (particle number and PM2.5), Road Type (PM10) and Size Range Measured and Speed Limit on the Road (particle volume). Discussion A multiplicity of factors need to be considered in determining emission factors that are suitable for modelling motor vehicle emissions, and this study derived a set of average emission factors suitable for quantifying motor vehicle tailpipe particle emissions in developed countries. Conclusions The comprehensive set of tailpipe particle emission factors presented in this study for different vehicle and road type combinations enable the full size range of particles generated by fleets to be quantified, including ultrafine particles (measured in terms of particle number). These emission factors have particular application for regions which may have a lack of funding to undertake measurements, or insufficient measurement data upon which to derive emission factors for their region. Recommendations and perspectives In urban areas motor vehicles continue to be a major source of particulate matter pollution and of ultrafine particles. It is critical that in order to manage this major pollution source methods are available to quantify the full size range of particles emitted for traffic modelling and health impact assessments.

Attractiveness of venture idea amongst expert entrepreneurs : a conjoint analysis

Principal Topic Venture ideas are at the heart of entrepreneurship (Davidsson, 2004). However, we are yet to learn what factors drive entrepreneurs’ perceptions of the attractiveness of venture ideas, and what the relative importance of these factors are for their decision to pursue an idea. The expected financial gain is one factor that will obviously influence the perceived attractiveness of a venture idea (Shepherd & DeTienne, 2005). In addition, the degree of novelty of venture ideas along one or more dimensions such as new products/services, new method of production, enter into new markets/customer and new method of promotion may affect their attractiveness (Schumpeter, 1934). Further, according to the notion of an individual-opportunity nexus venture ideas are closely associated with certain individual characteristics (relatedness). Shane (2000) empirically identified that individual’s prior knowledge is closely associated with the recognition of venture ideas. Sarasvathy’s (2001; 2008) Effectuation theory proposes a high degree of relatedness between venture ideas and the resource position of the individual. This study examines how entrepreneurs weigh considerations of different forms of novelty and relatedness as well as potential financial gain in assessing the attractiveness of venture ideas. Method I use conjoint analysis to determine how expert entrepreneurs develop preferences for venture ideas which involved with different degrees of novelty, relatedness and potential gain. The conjoint analysis estimates respondents’ preferences in terms of utilities (or part-worth) for each level of novelty, relatedness and potential gain of venture ideas. A sample of 32 expert entrepreneurs who were awarded young entrepreneurship awards were selected for the study. Each respondent was interviewed providing with 32 scenarios which explicate different combinations of possible profiles open them into consideration. Results and Implications Results indicate that while the respondents do not prefer mere imitation they receive higher utility for low to medium degree of newness suggesting that high degrees of newness are fraught with greater risk and/or greater resource needs. Respondents pay considerable weight on alignment with the knowledge and skills they already posses in choosing particular venture idea. The initial resource position of entrepreneurs is not equally important. Even though expected potential financial gain gives substantial utility, result indicate that it is not a dominant factor for the attractiveness of venture idea.

Organ printing

Organ printing techniques offer the potential to produce living 3D tissue constructs to repair or replace damaged or diseased human tissues and organs. Using these techniques, spatial variations along multiple axes with high geometric complexity can be obtained.. The level of control offered by these technologies to develop printed tissues will allow tissue engineers to better study factors that modulate tissue formation and function, and provide a valuable tool to study the effect of anatomy on graft performance. In this chapter we discuss the history behind substrate patterning and cell and organ printing, and the rationale for developing organ printing techniques with respect to limitations of current clinical tissue engineering strategies to effectively repair damaged tissues. We discuss current 2-dimensional and 3-dimesional strategies for assembling cells as well as the necessary support materials such as hydrogels, bioinks and natural and synthetic polymers adopted for organ printing research. Furthermore, given the current state-of-the-art in organ printing technologies, we discuss some of their limitations and provide recommendations for future developments in this rapidly growing field.

Toothless tiger, sleeping dragon : implied freedoms, internet filters and the growing culture of internet censorship in Australia

The internet by its very nature challenges an individual’s notions of propriety, moral acuity and social correctness. A tension will always exist between the censorship of obscene and sensitive information and the freedom to publish and/or access such information. Freedom of expression and communication on the internet is not a static concept: ‘Its continual regeneration is the product of particular combinations of political, legal, cultural and philosophical conditions’.

The role of bricolage and resource constraints in high potential sustainability ventures

Sustainability decisions and their impacts may be among the greatest challenges facing the world in the 21st century (Davos 2000). Apart from adaptation on the part of established organizations these challenges are arguably going to require solutions developed by new actors However, young ventures have only recently begun generating research interest within sustainability literature (Shepherd et al. 2009). In particular, little is known about resource behaviours of these ventures and how they adapt to substantial resource constraints. One promising theory that has been identified as a way that some entrepreneurs manage constraints is bricolage: a construct defined as “making do by applying combinations of the resources at hand to new problems and opportunities” (Baker and Nelson 2005: 333). Bricolage may be critical as the means of continued venture success as these ventures are frequently developed in severe resource constraint, owing to higher levels of technical sophistication (Rothaermel and Deeds 2006). Further, they are often developed by entrepreneurs committed to personal and social goals of resourcefulness, including values that focus on conservation rather than consumption of resources (Shepherd et al. 2009). In this paper, using seven novel cases of high potential sustainability firms from CAUSEE we consider how constraints impact resource behaviours and further illustrate and extend bricolage domains previously developed by Baker and Nelson (2005) with recommendations for theory and practice provided.

Adapting to the work-life interface : the influence of individual differences, work and family on well-being, mental health and work engagement

Bronfenbrenner.s Bioecological Model, expressed as the developmental equation, D f PPCT, is the theoretical framework for two studies that bring together diverse strands of psychology to study the work-life interface of working adults. Occupational and organizational psychology is focused on the demands and resources of work and family, without emphasising the individual in detail. Health and personality psychology examine the individual but without emphasis on the individual.s work and family roles. The current research used Bronfenbrenner.s theoretical framework to combine individual differences, work and family to understand how these factors influence the working adult.s psychological functioning. Competent development has been defined as high well-being (measured as life satisfaction and psychological well-being) and high work engagement (as work vigour, work dedication and absorption in work) and as the absence of mental illness (as depression, anxiety and stress) and the absence of burnout (as emotional exhaustion, cynicism and professional efficacy). Study 1 and 2 were linked, with Study 1 as a cross-sectional survey and Study 2, a prospective panel study that followed on from the data used in Study1. Participants were recruited from a university and from a large public hospital to take part in a 3-wave, online study where they completed identical surveys at 3-4 month intervals (N = 470 at Time 1 and N = 198 at Time 3). In Study 1, hierarchical multiple regressions were used to assess the effects of individual differences (Block 1, e.g. dispositional optimism, coping self-efficacy, perceived control of time, humour), work and family variables (Block 2, e.g. affective commitment, skill discretion, work hours, children, marital status, family demands) and the work-life interface (Block 3, e.g. direction and quality of spillover between roles, work-life balance) on the outcomes. There were a mosaic of predictors of the outcomes with a group of seven that were the most frequent significant predictors and which represented the individual (dispositional optimism and coping self-efficacy), the workplace (skill discretion, affective commitment and job autonomy) and the work-life interface (negative work-to-family spillover and negative family-to-work spillover). Interestingly, gender and working hours were not important predictors. The effects of job social support, generally and for work-life issues, perceived control of time and egalitarian gender roles on the outcomes were mediated by negative work-to-family spillover, particularly for emotional exhaustion. Further, the effect of negative spillover on depression, anxiety and work engagement was moderated by the individual.s personal and workplace resources. Study 2 modelled the longitudinal relationships between the group of the seven most frequent predictors and the outcomes. Using a set of non-nested models, the relative influences of concurrent functioning, stability and change over time were assessed. The modelling began with models at Time 1, which formed the basis for confirmatory factor analysis (CFA) to establish the underlying relationships between the variables and calculate the composite variables for the longitudinal models. The CFAs were well fitting with few modifications to ensure good fit. However, using burnout and work engagement together required additional analyses to resolve poor fit, with one factor (representing a continuum from burnout to work engagement) being the only acceptable solution. Five different longitudinal models were investigated as the Well-Being, Mental Distress, Well-Being-Mental Health, Work Engagement and Integrated models using differing combinations of the outcomes. The best fitting model for each was a reciprocal model that was trimmed of trivial paths. The strongest paths were the synchronous correlations and the paths within variables over time. The reciprocal paths were more variable with weak to mild effects. There was evidence of gain and loss spirals between the variables over time, with a slight net gain in resources that may provide the mechanism for the accumulation of psychological advantage over a lifetime. The longitudinal models also showed that there are leverage points at which personal, psychological and managerial interventions can be targeted to bolster the individual and provide supportive workplace conditions that also minimise negative spillover. Bronfenbrenner.s developmental equation has been a useful framework for the current research, showing the importance of the person as central to the individual.s experience of the work-life interface. By taking control of their own life, the individual can craft a life path that is most suited to their own needs. Competent developmental outcomes were most likely where the person was optimistic and had high self-efficacy, worked in a job that they were attached to and which allowed them to use their talents and without too much negative spillover between their work and family domains. In this way, individuals had greater well-being, better mental health and greater work engagement at any one time and across time.

Melt electrospinning of polycaprolactone and its blends with poly(ethylene glycol)

Melt electrospinning is one aspect of electrospinning with relatively little published literature, although the technique avoids solvent accumulation and/or toxicity which is favoured in certain applications. In the study reported, we melt-electrospun blends of poly(ε-caprolactone) (PCL) and an amphiphilic diblock copolymer consisting of poly(ethylene glycol) and PCL segments (PEG-block-PCL). A custom-made electrospinning apparatus was built and various combinations of instrument parameters such as voltage and polymer feeding rate were investigated. Pure PEG-block-PCL copolymer melt electrospinning did not result in consistent and uniform fibres due to the low molecular weight, while blends of PCL and PEG-block-PCL, for some parameter combinations and certain weight ratios of the two components, were able to produce continuous fibres significantly thinner (average diameter of ca 2 µm) compared to pure PCL. The PCL fibres obtained had average diameters ranging from 6 to 33 µm and meshes were uniform for the lowest voltage employed while mesh uniformity decreased when the voltage was increased. This approach shows that PCL and blends of PEG-block-PCL and PCL can be readily processed by melt electrospinning to obtain fibrous meshes with varied average diameters and morphologies that are of interest for tissue engineering purposes. Copyright © 2010 Society of Chemical Industry

Alkaline hydrothermal treatment of titanate nanostructures

Since its initial proposal in 1998, alkaline hydrothermal processing has rapidly become an established technology for the production of titanate nanostructures. This simple, highly reproducible process has gained a strong research following since its conception. However, complete understanding and elucidation of nanostructure phase and formation have not yet been achieved. Without fully understanding phase, formation, and other important competing effects of the synthesis parameters on the final structure, the maximum potential of these nanostructures cannot be obtained. Therefore this study examined the influence of synthesis parameters on the formation of titanate nanostructures produced by alkaline hydrothermal treatment. The parameters included alkaline concentration, hydrothermal temperature, the precursor material‘s crystallite size and also the phase of the titanium dioxide precursor (TiO2, or titania). The nanostructure‘s phase and morphology was analysed using X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy. X-ray photoelectron spectroscopy (XPS), dynamic light scattering (non-invasive backscattering), nitrogen sorption, and Rietveld analysis were used to determine phase, for particle sizing, surface area determinations, and establishing phase concentrations, respectively. This project rigorously examined the effect of alkaline concentration and hydrothermal temperature on three commercially sourced and two self-prepared TiO2 powders. These precursors consisted of both pure- or mixed-phase anatase and rutile polymorphs, and were selected to cover a range of phase concentrations and crystallite sizes. Typically, these precursors were treated with 5–10 M sodium hydroxide (NaOH) solutions at temperatures between 100–220 °C. Both nanotube and nanoribbon morphologies could be produced depending on the combination of these hydrothermal conditions. Both titania and titanate phases are comprised of TiO6 units which are assembled in different combinations. The arrangement of these atoms affects the binding energy between the Ti–O bonds. Raman spectroscopy and XPS were therefore employed in a preliminary study of phase determination for these materials. The change in binding energy from a titania to a titanate binding energy was investigated in this study, and the transformation of titania precursor into nanotubes and titanate nanoribbons was directly observed by these methods. Evaluation of the Raman and XPS results indicated a strengthening in the binding energies of both the Ti (2p3/2) and O (1s) bands which correlated to an increase in strength and decrease in resolution of the characteristic nanotube doublet observed between 320 and 220 cm.1 in the Raman spectra of these products. The effect of phase and crystallite size on nanotube formation was examined over a series of temperatures (100.200 �‹C in 20 �‹C increments) at a set alkaline concentration (7.5 M NaOH). These parameters were investigated by employing both pure- and mixed- phase precursors of anatase and rutile. This study indicated that both the crystallite size and phase affect nanotube formation, with rutile requiring a greater driving force (essentially �\harsher. hydrothermal conditions) than anatase to form nanotubes, where larger crystallites forms of the precursor also appeared to impede nanotube formation slightly. These parameters were further examined in later studies. The influence of alkaline concentration and hydrothermal temperature were systematically examined for the transformation of Degussa P25 into nanotubes and nanoribbons, and exact conditions for nanostructure synthesis were determined. Correlation of these data sets resulted in the construction of a morphological phase diagram, which is an effective reference for nanostructure formation. This morphological phase diagram effectively provides a .recipe book�e for the formation of titanate nanostructures. Morphological phase diagrams were also constructed for larger, near phase-pure anatase and rutile precursors, to further investigate the influence of hydrothermal reaction parameters on the formation of titanate nanotubes and nanoribbons. The effects of alkaline concentration, hydrothermal temperature, crystallite phase and size are observed when the three morphological phase diagrams are compared. Through the analysis of these results it was determined that alkaline concentration and hydrothermal temperature affect nanotube and nanoribbon formation independently through a complex relationship, where nanotubes are primarily affected by temperature, whilst nanoribbons are strongly influenced by alkaline concentration. Crystallite size and phase also affected the nanostructure formation. Smaller precursor crystallites formed nanostructures at reduced hydrothermal temperature, and rutile displayed a slower rate of precursor consumption compared to anatase, with incomplete conversion observed for most hydrothermal conditions. The incomplete conversion of rutile into nanotubes was examined in detail in the final study. This study selectively examined the kinetics of precursor dissolution in order to understand why rutile incompletely converted. This was achieved by selecting a single hydrothermal condition (9 M NaOH, 160 °C) where nanotubes are known to form from both anatase and rutile, where the synthesis was quenched after 2, 4, 8, 16 and 32 hours. The influence of precursor phase on nanostructure formation was explicitly determined to be due to different dissolution kinetics; where anatase exhibited zero-order dissolution and rutile second-order. This difference in kinetic order cannot be simply explained by the variation in crystallite size, as the inherent surface areas of the two precursors were determined to have first-order relationships with time. Therefore, the crystallite size (and inherent surface area) does not affect the overall kinetic order of dissolution; rather, it determines the rate of reaction. Finally, nanostructure formation was found to be controlled by the availability of dissolved titanium (Ti4+) species in solution, which is mediated by the dissolution kinetics of the precursor.

The role of non-factorizability in determining "pseudo-classical" non-separability

This article introduces a “pseudo classical” notion of modelling non-separability. This form of non-separability can be viewed as lying between separability and quantum-like non-separability. Non-separability is formalized in terms of the non-factorizabilty of the underlying joint probability distribution. A decision criterium for determining the non-factorizability of the joint distribution is related to determining the rank of a matrix as well as another approach based on the chi-square-goodness-of-fit test. This pseudo-classical notion of non-separability is discussed in terms of quantum games and concept combinations in human cognition.

The ghrelin receptor isoforms (GHS-R1a and GHS-R1b) and GPR39 : an investigation into receptor dimerisation

Prostate cancer is the second most common cause of cancer-related deaths in Western males. Current diagnostic, prognostic and treatment approaches are not ideal and advanced metastatic prostate cancer is incurable. There is an urgent need for improved adjunctive therapies and markers for this disease. GPCRs are likely to play a significant role in the initiation and progression of prostate cancer. Over the last decade, it has emerged that G protein coupled receptors (GPCRs) are likely to function as homodimers and heterodimers. Heterodimerisation between GPCRs can result in the formation of novel pharmacological receptors with altered functional outcomes, and a number of GPCR heterodimers have been implicated in the pathogenesis of human disease. Importantly, novel GPCR heterodimers represent potential new targets for the development of more specific therapeutic drugs. Ghrelin is a 28 amino acid peptide hormone which has a unique n-octanoic acid post-translational modification. Ghrelin has a number of important physiological roles, including roles in appetite regulation and the stimulation of growth hormone release. The ghrelin receptor is the growth hormone secretagogue receptor type 1a, GHS-R1a, a seven transmembrane domain GPCR, and GHS-R1b is a C-terminally truncated isoform of the ghrelin receptor, consisting of five transmembrane domains. Growing evidence suggests that ghrelin and the ghrelin receptor isoforms, GHS-R1a and GHS-R1b, may have a role in the progression of a number of cancers, including prostate cancer. Previous studies by our research group have shown that the truncated ghrelin receptor isoform, GHS-R1b, is not expressed in normal prostate, however, it is expressed in prostate cancer. The altered expression of this truncated isoform may reflect a difference between a normal and cancerous state. A number of mutant GPCRs have been shown to regulate the function of their corresponding wild-type receptors. Therefore, we investigated the potential role of interactions between GHS-R1a and GHS-R1b, which are co-expressed in prostate cancer and aimed to investigate the function of this potentially new pharmacological receptor. In 2005, obestatin, a 23 amino acid C-terminally amidated peptide derived from preproghrelin was identified and was described as opposing the stimulating effects of ghrelin on appetite and food intake. GPR39, an orphan GPCR which is closely related to the ghrelin receptor, was identified as the endogenous receptor for obestatin. Recently, however, the ability of obestatin to oppose the effects of ghrelin on appetite and food intake has been questioned, and furthermore, it appears that GPR39 may in fact not be the obestatin receptor. The role of GPR39 in the prostate is of interest, however, as it is a zinc receptor. Zinc has a unique role in the biology of the prostate, where it is normally accumulated at high levels, and zinc accumulation is altered in the development of prostate malignancy. Ghrelin and zinc have important roles in prostate cancer and dimerisation of their receptors may have novel roles in malignant prostate cells. The aim of the current study, therefore, was to demonstrate the formation of GHS-R1a/GHS-R1b and GHS-R1a/GPR39 heterodimers and to investigate potential functions of these heterodimers in prostate cancer cell lines. To demonstrate dimerisation we first employed a classical co-immunoprecipitation technique. Using cells co-overexpressing FLAG- and Myc- tagged GHS-R1a, GHS-R1b and GPR39, we were able to co-immunoprecipitate these receptors. Significantly, however, the receptors formed high molecular weight aggregates. A number of questions have been raised over the propensity of GPCRs to aggregate during co-immunoprecipitation as a result of their hydrophobic nature and this may be misinterpreted as receptor dimerisation. As we observed significant receptor aggregation in this study, we used additional methods to confirm the specificity of these putative GPCR interactions. We used two different resonance energy transfer (RET) methods; bioluminescence resonance energy transfer (BRET) and fluorescence resonance energy transfer (FRET), to investigate interactions between the ghrelin receptor isoforms and GPR39. RET is the transfer of energy from a donor fluorophore to an acceptor fluorophore when they are in close proximity, and RET methods are, therefore, applicable to the observation of specific protein-protein interactions. Extensive studies using the second generation bioluminescence resonance energy transfer (BRET2) technology were performed, however, a number of technical limitations were observed. The substrate used during BRET2 studies, coelenterazine 400a, has a low quantum yield and rapid signal decay. This study highlighted the requirement for the expression of donor and acceptor tagged receptors at high levels so that a BRET ratio can be determined. After performing a number of BRET2 experimental controls, our BRET2 data did not fit the predicted results for a specific interaction between these receptors. The interactions that we observed may in fact represent ‘bystander BRET’ resulting from high levels of expression, forcing the donor and acceptor into close proximity. Our FRET studies employed two different FRET techniques, acceptor photobleaching FRET and sensitised emission FRET measured by flow cytometry. We were unable to observe any significant FRET, or FRET values that were likely to result from specific receptor dimerisation between GHS-R1a, GHS-R1b and GPR39. While we were unable to conclusively demonstrate direct dimerisation between GHS-R1a, GHS-R1b and GPR39 using several methods, our findings do not exclude the possibility that these receptors interact. We aimed to investigate if co-expression of combinations of these receptors had functional effects in prostate cancers cells. It has previously been demonstrated that ghrelin stimulates cell proliferation in prostate cancer cell lines, through ERK1/2 activation, and GPR39 can stimulate ERK1/2 signalling in response to zinc treatments. Additionally, both GHS-R1a and GPR39 display a high level of constitutive signalling and these constitutively active receptors can attenuate apoptosis when overexpressed individually in some cell types. We, therefore, investigated ERK1/2 and AKT signalling and cell survival in prostate cancer the potential modulation of these functions by dimerisation between GHS-R1a, GHS-R1b and GPR39. Expression of these receptors in the PC-3 prostate cancer cell line, either alone or in combination, did not alter constitutive ERK1/2 or AKT signalling, basal apoptosis or tunicamycin-stimulated apoptosis, compared to controls. In summary, the potential interactions between the ghrelin receptor isoforms, GHS-R1a and GHS-R1b, and the related zinc receptor, GPR39, and the potential for functional outcomes in prostate cancer were investigated using a number of independent methods. We did not definitively demonstrate the formation of these dimers using a number of state of the art methods to directly demonstrate receptor-receptor interactions. We investigated a number of potential functions of GPR39 and GHS-R1a in the prostate and did not observe altered function in response to co-expression of these receptors. The technical questions raised by this study highlight the requirement for the application of extensive controls when using current methods for the demonstration of GPCR dimerisation. Similar findings in this field reflect the current controversy surrounding the investigation of GPCR dimerisation. Although GHS-R1a/GHS-R1b or GHS-R1a/GPR39 heterodimerisation was not clearly demonstrated, this study provides a basis for future investigations of these receptors in prostate cancer. Additionally, the results presented in this study and growing evidence in the literature highlight the requirement for an extensive understanding of the experimental method and the performance of a range of controls to avoid the spurious interpretation of data gained from artificial expression systems. The future development of more robust techniques for investigating GPCR dimerisation is clearly required and will enable us to elucidate whether GHS-R1a, GHS-R1b and GPR39 form physiologically relevant dimers.

Detection of dsRNA in Grapevines Showing Symptoms of Rupestris Stem Pitting Disease and the Variabilities Encountered

Rupestris stem pitting (rSP), a graft-transmissible grapevine disease, can be identified only by its reaction (pitted wood) on inoculated Vitis rupestris ‘St. George.’ DsRNA was extracted from grapevines from California and Canada that indexed positive for rSP on St. George. Two distinct dsRNA species (B and C) (Mr = 5.3 × 106 and 4.4 × 106, respectively) were detected from the stem tissue of rSP-positive samples. Although similar dsRNA species (B and C) were detected in extracts of grapevines from New York, the association of dsRNA B and C with rSP in New York samples was not consistent. Also, eight different dsRNAs, known to be associated with the powdery mildew fungus, Uncinula necator, were detected in leaves of New York samples. In New York, the dsRNAs were not observed in leaves or stem samples collected from June through late August during the 1988 and 1989 growing seasons, suggesting that dsRNA detection in the grape tissue is variable throughout the season. We suggest that dsRNA species B and C are associated with rSP disease. The inconsistent results with New York samples are discussed.

Structure of selected basic zinc/copper (II) phosphate minerals based upon near-infrared spectroscopy : implications for hydrogen bonding

The NIR spectra of reichenbachite, scholzite and parascholzite have been studied at 298 K. The spectra of the minerals are different, in line with composition and crystal structural variations. Cation substitution effects are significant in their electronic spectra and three distinctly different electronic transition bands are observed in the near-infrared spectra at high wavenumbers in the 12000-7600 cm-1 spectral region. Reichenbachite electronic spectrum is characterised by Cu(II) transition bands at 9755 and 7520 cm-1. A broad spectral feature observed for ferrous ion in the 12000-9000 cm-1 region both in scholzite and parascholzite. Some what similarities in the vibrational spectra of the three phosphate minerals are observed particularly in the OH stretching region. The observation of strong band at 5090 cm-1 indicates strong hydrogen bonding in the structure of the dimorphs, scholzite and parascholzite. The three phosphates exhibit overlapping bands in the 4800-4000 cm-1 region resulting from the combinations of vibrational modes of (PO4)3- units.

Modification and validation of a microwave-assisted digestion method for subsequent ICP-MS determination of selected heavy metals in sediment and fish samples in Agusan River, Philippines

This study investigated, validated, and applied the optimum conditions for a modified microwave assisted digestion method for subsequent ICP-MS determination of mercury, cadmium, and lead in two matrices relevant to water quality, that is, sediment and fish. Three different combinations of power, pressure, and time conditions for microwave-assisted digestion were tested, using two certified reference materials representing the two matrices, to determine the optimum set of conditions. Validation of the optimized method indicated better recovery of the studied metals compared to standard methods. The validated method was applied to sediment and fish samples collected from Agusan River and one of its tributaries, located in Eastern Mindanao, Philippines. The metal concentrations in sediment ranged from 2.85 to 341.06 mg/kg for Hg, 0.05 to 44.46 mg/kg for Cd and 2.20 to 1256.16 mg/kg for Pb. The results indicate that the concentrations of these metals in the sediments rapidly decrease with distance downstream from sites of contamination. In the selected fish species, the metals were detected but at levels that are considered safe for human consumption, with concentrations of 2.14 to 6.82 μg/kg for Hg, 0.035 to 0.068 μg/kg for Cd, and 0.019 to 0.529 μg/kg for Pb.

Cultivar-specific effects of pathogen testing on storage root yield of sweet potato, Ipomoea batatas (L.) Lam.

The accumulation and perpetuation of viral pathogens over generations of clonal propagation in crop species such as sweet potato, Ipomoea batatas,inevitably result in a reduction in crop yield and quality. This study was conducted at Bundaberg, Australia to compare the productivity of field-derived and pathogen-tested (PT)clones of 14 sweet potato cultivars and the yield benefits of using healthy planting materials. The field-derived clonal materials were exposed to the endemic viruses, while the PT clones were subjected to thermotherapy and meristem-tip culture to eliminate viral pathogens. The plants were indexed for viruses using nitrocellulose membrane-enzyme-linked immunosorbent assay and graft-inoculations onto Ipomoea setosa. A net benefit of 38% in storage root yield was realised from using PT materials in this study.Conversely, in a similar study previously conducted at Kerevat, Papua New Guinea (PNG), a net deficit of 36% was realised. This reinforced our finding that the response to pathogen testing was cultivar dependent and that the PNG cultivars in these studies generally exhibited increased tolerance to the endemic viruses present at the respective trial sites as manifested in their lack of response from the use of PT clones. They may be useful sources for future resistance breeding efforts. Nonetheless, the potential economic gain from using PT stocks necessitates the use of pathogen testing on virus-susceptible commercial cultivars.