Power converters design and analysis for high power piezoelectric ultrasonic transducers

High power piezoelectric ultrasonic transducers have been widely exploited in a variety of applications. The critical behaviour of a piezoelectric device is encapsulated in its resonant frequencies because of its maximum transmission performance at these frequencies. Therefore power electronic converters should be tuned at those resonant frequencies to transfer electrical power to mechanical power efficiently. However, structural and environmental changes cause variations in the device resonant frequencies which can degrade the system performance. Hence, estimating the device resonant frequencies within the incorporated setup can significantly improve the system performance. This paper proposes an efficient resonant frequency estimation approach to maintain the performance of high power ultrasonic applications using the employed power converter. Experimental validations indicate the effectiveness of the proposed method.

Mechanical testing and modelling of a bone-implant construct

Finite Element modelling of bone fracture fixation systems allows computational investigation of the deformation response of the bone to load. Once validated, these models can be easily adapted to explore changes in design or configuration of a fixator. The deformation of the tissue within the fracture gap determines its healing and is often summarised as the stiffness of the construct. FE models capable of reproducing this behaviour would provide valuable insight into the healing potential of different fixation systems. Current model validation techniques lack depth in 6D load and deformation measurements. Other aspects of the FE model creation such as the definition of interfaces between components have also not been explored. This project investigated the mechanical testing and FE modelling of a bone– plate construct for the determination of stiffness. In depth 6D measurement and analysis of the generated forces, moments and movements showed large out of plane behaviours which had not previously been characterised. Stiffness calculated from the interfragmentary movement was found to be an unsuitable summary parameter as the error propagation is too large. Current FE modelling techniques were applied in compression and torsion mimicking the experimental setup. Compressive stiffness was well replicated, though torsional stiffness was not. The out of plane behaviours prevalent in the experimental work were not replicated in the model. The interfaces between the components were investigated experimentally and through modification to the FE model. Incorporation of the interface modelling techniques into the full construct models had no effect in compression but did act to reduce torsional stiffness bringing it closer to that of the experiment. The interface definitions had no effect on out of plane behaviours, which were still not replicated. Neither current nor novel FE modelling techniques were able to replicate the out of plane behaviours evident in the experimental work. New techniques for modelling loads and boundary conditions need to be developed to mimic the effects of the entire experimental system.

Biomechanical aspects of seating comfort in vehicle seating package engineering

In this paper, problems are described which are related to the ergonomic assessment of vehicle package design in vehicle systems engineering. The traditional approach, using questionnaire techniques for a subjective assessment of comfort related to package design, is compared to a biomechanical approach. An example is given for ingress design. The biomechanical approach is based upon objective postural data. The experimental setup for the study is described and methods used for the biomechanical analysis are explained. Because the biomechanic assessment requires not only a complex experimental setup but also time consuming data processing, a systematic reduction and preparation of biomechanic data for classification with an Artificial Neural Network significantly improves the economy of the biomechanical method.

Sunshine, rainfall, humidity and child pneumonia in the tropics : time-series analyses

Few studies have formally examined the relationship between meteorological factors and the incidence of child pneumonia in the tropics, despite the fact that most child pneumonia deaths occur there. We examined the association between four meteorological exposures (rainy days, sunshine, relative humidity, temperature) and the incidence of clinical pneumonia in young children in the Philippines using three time-series methods: correlation of seasonal patterns, distributed lag regression, and case-crossover. Lack of sunshine was most strongly associated with pneumonia in both lagged regression [overall relative risk over the following 60 days for a 1-h increase in sunshine per day was 0·67 (95% confidence interval (CI) 0·51–0·87)] and case-crossover analysis [odds ratio for a 1-h increase in mean daily sunshine 8–14 days earlier was 0·95 (95% CI 0·91–1·00)]. This association is well known in temperate settings but has not been noted previously in the tropics. Further research to assess causality is needed.

A systematic approach for selecting lean strategies and assessing leanness in manufacturing organizations

Lean strategies have been developed to eliminate or reduce manufacturing waste and thus improve operational efficiency in manufacturing processes. However, implementing lean strategies requires a large amount of resources and, in practice, manufacturers encounter difficulties in selecting appropriate lean strategies within their resource constraints. There is currently no systematic methodology available for selecting appropriate lean strategies within a manufacturer's resource constraints. In the lean transformation process, it is also critical to measure the current and desired leanness levels in order to clearly evaluate lean implementation efforts. Despite the fact that many lean strategies are utilized to reduce or eliminate manufacturing waste, little effort has been directed towards properly assessing the leanness of manufacturing organizations. In practice, a single or specific group of metrics (either qualitative or quantitative) will only partially measure the overall leanness. Existing leanness assessment methodologies do not offer a comprehensive evaluation method, integrating both quantitative and qualitative lean measures into a single quantitative value for measuring the overall leanness of an organization. This research aims to develop mathematical models and a systematic methodology for selecting appropriate lean strategies and evaluating the leanness levels in manufacturing organizations. Mathematical models were formulated and a methodology was developed for selecting appropriate lean strategies within manufacturers' limited amount of available resources to reduce their identified wastes. A leanness assessment model was developed by using the fuzzy concept to assess the leanness level and to recommend an optimum leanness value for a manufacturing organization. In the proposed leanness assessment model, both quantitative and qualitative input factors have been taken into account. Based on program developed in MATLAB and C#, a decision support tool (DST) was developed for decision makers to select lean strategies and evaluate the leanness value based on the proposed models and methodology hence sustain the lean implementation efforts. A case study was conducted to demonstrate the effectiveness of these proposed models and methodology. Case study results suggested that out of 10 wastes identified, the case organization (ABC Limited) is able to improve a maximum of six wastes from the selected workstation within their resource limitations. The selected wastes are: unnecessary motion, setup time, unnecessary transportation, inappropriate processing, work in process and raw material inventory and suggested lean strategies are: 5S, Just-In-Time, Kanban System, the Visual Management System (VMS), Cellular Manufacturing, Standard Work Process using method-time measurement (MTM), and Single Minute Exchange of Die (SMED). From the suggested lean strategies, the impact of 5S was demonstrated by measuring the leanness level of two different situations in ABC. After that, MTM was suggested as a standard work process for further improvement of the current leanness value. The initial status of the organization showed a leanness value of 0.12. By applying 5S, the leanness level significantly improved to reach 0.19 and the simulation of MTM as a standard work method shows the leanness value could be improved to 0.31. The optimum leanness value of ABC was calculated to be 0.64. These leanness values provided a quantitative indication of the impacts of improvement initiatives in terms of the overall leanness level to the case organization. Sensitivity analsysis and a t-test were also performed to validate the model proposed. This research advances the current knowledge base by developing mathematical models and methodologies to overcome lean strategy selection and leanness assessment problems. By selecting appropriate lean strategies, a manufacturer can better prioritize implementation efforts and resources to maximize the benefits of implementing lean strategies in their organization. The leanness index is used to evaluate an organization's current (before lean implementation) leanness state against the state after lean implementation and to establish benchmarking (the optimum leanness state). Hence, this research provides a continuous improvement tool for a lean manufacturing organization.

Closing the gap between copyright and designs : an age of enlightnement or state of confusion?

The arena of intellectual property encompasses streams that often interrelate and overlap in protecting different aspects of intellectual property. Australian commentators suggest that ‘one of the most troublesome areas in the entire field of intellectual property has been the relationship between copyright protection for artistic works under the Copyright Act 1968 (Cth) and protection for registered designs under the Designs Act 1906 (Cth).’ [McKeough, J., Stewart, A., & Griffith, P. (2004). Intellectual property in Australia (3rd ed.). Chatswood, NSW: Butterworths.] [Ricketson, S., Richardson, M., & Davison, M. (2009). Intellectual property: Cases, materials and commentary (4th ed.). Chatswood, NSW: LexisNexis Butterworths.] This overlap has caused much confusion for both creators of artistic works and industrial designs, as there is an uncertainty of whether protection against infringement is afforded under the Copyright Act 1988 (Cth) or whether the Designs Act 2003 (Cth) will apply. In Australia, there is limited precedent that examines the crossover between copyright and designs. Essentially, the cases that have tested this issue remain unclear as to whether a design applied industrially will invoke copyright protection. The cases demonstrate that there is an inconsistency in this area despite the aims of the new provisions of the Designs Act 2003 (Cth) to close the loopholes between copyright and designs. This paper will discuss and evaluate the relationship between copyright protection for artistic works and protection for registered designs with respect to the Designs Act 2003 (Cth).

High rates of muscle glycogen resynthesis after exhaustive exercise when carbohydrate is coingested with caffeine

We determined the effect of coingestion of caffeine (Caff) with carbohydrate (CHO) on rates of muscle glycogen resynthesis during recovery from exhaustive exercise in seven trained subjects who completed two experimental trials in a randomized, double-blind crossover design. The evening before an experiment subjects performed intermittent exhaustive cycling and then consumed a low-CHO meal. The next morning subjects rode until volitional fatigue. On completion of this ride subjects consumed either CHO [4 g/kg body mass (BM)] or the same amount of CHO + Caff (8 mg/kg BM) during 4 h of passive recovery. Muscle biopsies and blood samples were taken at regular intervals throughout recovery. Muscle glycogen levels were similar at exhaustion [?75 mmol/kg dry wt (dw)] and increased by a similar amount (?80%) after 1 h of recovery (133 ± 37.8 vs. 149 ± 48 mmol/kg dw for CHO and Caff, respectively). After 4 h of recovery Caff resulted in higher glycogen accumulation (313 ± 69 vs. 234 ± 50 mmol/kg dw, P < 0.001). Accordingly, the overall rate of resynthesis for the 4-h recovery period was 66% higher in Caff compared with CHO (57.7 ± 18.5 vs. 38.0 ± 7.7 mmol·kg dw-1·h-1, P < 0.05). After 1 h of recovery plasma Caff levels had increased to 31 ± 11 ?M (P < 0.001) and at the end of the recovery reached 77 ± 11 ?M (P < 0.001) with Caff. Phosphorylation of CaMKThr286 was similar after exercise and after 1 h of recovery, but after 4 h CaMKThr286 phosphorylation was higher in Caff than CHO (P < 0.05). Phosphorylation of AMP-activated protein kinase (AMPK)Thr172 and AktSer473 was similar for both treatments at all time points. We provide the first evidence that in trained subjects coingestion of large amounts of Caff (8 mg/kg BM) with CHO has an additive effect on rates of postexercise muscle glycogen accumulation compared with consumption of CHO alone.

Bioequivalence of two tablet formulations of capecitabine and exploration of age, gender, body surface area, and creatinine clearance as factors influencing systemic exposure in cancer patients

Purpose: The objective of the study was to assess the bioequivalence of two tablet formulations of capecitabine and to explore the effect of age, gender, body surface area and creatinine clearance on the systemic exposure to capecitabine and its metabolites. Methods: The study was designed as an open, randomized two-way crossover trial. A single oral dose of 2000 mg capecitabine was administered on two separate days to 25 patients with solid tumors. On one day, the patients received four 500-mg tablets of formulation B (test formulation) and on the other day, four 500-mg tablets of formulation A (reference formulation). The washout period between the two administrations was between 2 and 8 days. After each administration, serial blood and urine samples were collected for up to 12 and 24 h, respectively. Unchanged capecitabine and its metabolites were determined in plasma using LC/MS-MS and in urine by NMRS. Results: Based on the primary pharmacokinetic parameter, AUC(0-∞) of 5'-DFUR, equivalence was concluded for the two formulations, since the 90% confidence interval of the estimate of formulation B relative to formulation A of 97% to 107% was within the acceptance region 80% to 125%. There was no clinically significant difference between the t(max) for the two formulations (median 2.1 versus 2.0 h). The estimate for C(max) was 111% for formulation B compared to formulation A and the 90% confidence interval of 95% to 136% was within the reference region 70% to 143%. Overall, these results suggest no relevant difference between the two formulations regarding the extent to which 5'-DFUR reached the systemic circulation and the rate at which 5'-DFUR appeared in the systemic circulation. The overall urinary excretions were 86.0% and 86.5% of the dose, respectively, and the proportion recovered as each metabolite was similar for the two formulations. The majority of the dose was excreted as FBAL (61.5% and 60.3%), all other chemical species making a minor contribution. Univariate and multivariate regression analysis to explore the influence of age, gender, body surface area and creatinine clearance on the log-transformed pharmacokinetic parameters AUC(0-∞) and C(max) of capecitabine and its metabolites revealed no clinically significant effects. The only statistically significant results were obtained for AUC(0-∞) and C(max) of intact drug and for C(max) of FBAL, which were higher in females than in males. Conclusion: The bioavailability of 5'-DFUR in the systemic circulation was practically identical after administration of the two tablet formulations. Therefore, the two formulations can be regarded as bioequivalent. The variables investigated (age, gender, body surface area, and creatinine clearance) had no clinically significant effect on the pharmacokinetics of capecitabine or its metabolites.

Bioavailability study of oral and intravenous OGT 719, a novel nucleoside analogue with preferential activity in the liver

Purpose: Although oral fluoropyrimidine pro-drugs are increasingly being administered in preference to intravenous nucleoside analogues in cancer chemotherapy, their activation in malignant liver tissue may be insufficient. OGT 719 (1-galactopyranosyl-5-fluorouracil) is a novel nucleoside analogue, preferentially localized in hepatocytes and hepatoma cells via the asialoglycoprotein receptor. The aim of this study was to assess the systemic bioavailability of this rationally designed drug in 16 patients with advanced solid cancers. Method: Crossover pharmacokinetic study of oral (400 or 800 mg) and intravenous (250 mg/m 2) OGT 719. Results: Linear pharmacokinetics and oral bioavailability of approximately 25% were observed at the dose levels used in this study. Like other 5-FU prodrugs, considerable interpatient variability was observed in bioavailability following oral dosing. The mean half-life for oral doses was 4 h. OGT 719 was well tolerated. No objective tumour responses were demonstrated. Conclusion: The systemic bioavailability and half-life of oral OGT 719 are sufficient to merit dose escalation studies with frequent daily dosing. Subsequent efficacy studies should be performed in patients with primary and secondary liver malignancies.

Bioavailability study of oral and intravenous OGT 719, a novel nucleoside analogue with preferential activity in the liver

Purpose: Although oral fluoropyrimidine pro-drugs are increasingly being administered in preference to intravenous nucleoside analogues in cancer chemotherapy, their activation in malignant liver tissue may be insufficient. OGT 719 (1-galactopyranosyl-5-fluorouracil) is a novel nucleoside analogue, preferentially localized in hepatocytes and hepatoma cells via the asialoglycoprotein receptor. The aim of this study was to assess the systemic bioavailability of this rationally designed drug in 16 patients with advanced solid cancers. Method: Crossover pharmacokinetic study of oral (400 or 800 mg) and intravenous (250 mg/m 2) OGT 719. Results: Linear pharmacokinetics and oral bioavailability of approximately 25% were observed at the dose levels used in this study. Like other 5-FU prodrugs, considerable interpatient variability was observed in bioavailability following oral dosing. The mean half-life for oral doses was 4 h. OGT 719 was well tolerated. No objective tumour responses were demonstrated. Conclusion: The systemic bioavailability and half-life of oral OGT 719 are sufficient to merit dose escalation studies with frequent daily dosing. Subsequent efficacy studies should be performed in patients with primary and secondary liver malignancies.

Foot massage versus quiet presence on agitation and mood in people with dementia : a randomised controlled trial

Background There is increasing interest in using complementary and alternative treatments to manage behavioural and psychological symptoms of dementia such as agitation, aggression and depressed mood. Objective To compare the effect of foot massage (intervention) and quiet presence (control) on agitation and mood in people with dementia. Design A randomised controlled trial using a within-subjects, crossover design. Settings Five long-term care facilities in Brisbane, Australia. The primary outcome was the Cohen-Mansfield Agitation Inventory (CMAI) and the secondary outcome was the Observed Emotion Rating Scale (OERS). The screening and data collection research assistants, families, and care staff were blinded to participant allocation. Participants Participants of the study were 55 long-term care residents aged 74–103 years (mean age 86.5), with moderate to severe dementia and a history of agitated behaviour according to the Pittsburgh Agitation Scale. A computer-program randomised participants to 10-min foot massage (intervention) or quiet presence (control), every weekday for 3 weeks. Results A carry-over effect was identified in the data, and so the data was treated as a parallel groups RCT. The mean total CMAI increased in both groups (reflecting an increase in agitation) with this increase greater in the quiet presence group than the foot massage group (p=0.03). There was a trend towards a difference on OERS General Alertness, with a positive change in alertness for participants in the foot massage group (indicating reduced alertness) and a negative change for participants in the quiet presence group (indicating increased alertness) (F(1,51)=3.88, p=0.05, partial ή2=0.07). Conclusions The findings highlight the need for further research on the specific conditions under which massage might promote relaxation and improve mood for people with dementia. The unfamiliar research assistants and variations in usual activity may have contributed to the increase in agitation and this needs further research.

Foot massage and physiological stress in people with dementia : a randomized controlled trial

Background There is increasing interest in using complementary and alternative treatments to manage behavioural and psychological symptoms of dementia such as agitation, aggression and depressed mood. Objective To compare the effect of foot massage (intervention) and quiet presence (control) on agitation and mood in people with dementia. Design A randomised controlled trial using a within-subjects, crossover design. Settings Five long-term care facilities in Brisbane, Australia. The primary outcome was the Cohen-Mansfield Agitation Inventory (CMAI) and the secondary outcome was the Observed Emotion Rating Scale (OERS). The screening and data collection research assistants, families, and care staff were blinded to participant allocation. Participants Participants of the study were 55 long-term care residents aged 74–103 years (mean age 86.5), with moderate to severe dementia and a history of agitated behaviour according to the Pittsburgh Agitation Scale. A computer-program randomised participants to 10-min foot massage (intervention) or quiet presence (control), every weekday for 3 weeks. Results A carry-over effect was identified in the data, and so the data was treated as a parallel groups RCT. The mean total CMAI increased in both groups (reflecting an increase in agitation) with this increase greater in the quiet presence group than the foot massage group (p=0.03). There was a trend towards a difference on OERS General Alertness, with a positive change in alertness for participants in the foot massage group (indicating reduced alertness) and a negative change for participants in the quiet presence group (indicating increased alertness) (F(1,51)=3.88, p=0.05, partial ή2=0.07). Conclusions The findings highlight the need for further research on the specific conditions under which massage might promote relaxation and improve mood for people with dementia. The unfamiliar research assistants and variations in usual activity may have contributed to the increase in agitation and this needs further research.

A multi-touch notice board fostering social interaction

We report on an alternative OCGM interface for a bulletin board, where a user can pin a note or a drawing, and actually shares contents. Exploiting direct and continuous manipulations, opposite to discrete gestures, to explore containers, the proposed interface supports a more natural and immediate interaction. It manages also the presence of different simultaneous users, allowing for the creation of local multimedia contents, the connection to social networks, providing a suitable working environment for cooperative and collaborative tasks in a multi-touch setup, such as touch-tables, interactive walls or multimedia boards

A 3D virtual medical imaging suite : bridging the academic-clinical training boundary

Aims The Medical Imaging Training Immersive Environment (MITIE) system is a recently developed virtual reality (VR) platform that allows students to practice a range of medical imaging techniques. The aim of this pilot study was to harvest user feedback about the educational value of the application and inform future pedagogical development. This presentation explores the use of this technology for skills training and blurring the boundaries between academic learning and clinical skills training. Background MITIE is a 3D VR environment that allows students to manipulate a patient and radiographic equipment in order to produce a VR-generated image for comparison with a gold standard. As with VR initiatives in other health disciplines (1-6) the software mimics clinical practice as much as possible and uses 3D technology to enhance immersion and realism. The software was developed by the Medical Imaging Course Team at a provider University with funding from a Health Workforce Australia “Simulated Learning Environments” grant. Methods Over 80 students undertaking the Bachelor of Medical Imaging Course were randomised to receive practical experience with either MITIE or radiographic equipment in the medical radiation laboratory. Student feedback about the educational value of the software was collected and performance with an assessed setup was measured for both groups for comparison. Ethical approval for the project was provided by the university ethics panel. Results This presentation provides qualitative analysis of student perceptions relating to satisfaction, usability and educational value as well as comparative quantitative performance data. Students reported high levels of satisfaction and both feedback and assessment results confirmed the application’s significance as a pre-clinical training tool. There was a clear emerging theme that MITIE could be a useful learning tool that students could access to consolidate their clinical learning, either during their academic timetables or their clinical placement. Conclusion Student feedback and performance data indicate that MITIE has a valuable role to play in the clinical skills training for medical imaging students both in the academic and the clinical environment. Future work will establish a framework for an appropriate supporting pedagogy that can cross the boundary between the two environments. This project was possible due to funding made available by Health Workforce Australia.

Physiological tolerance times while wearing explosive ordnance disposal protective clothing in simulated environmental extremes

Explosive ordnance disposal (EOD) technicians are required to wear protective clothing to protect themselves from the threat of overpressure, fragmentation, impact and heat. The engineering requirements to minimise these threats results in an extremely heavy and cumbersome clothing ensemble that increases the internal heat generation of the wearer, while the clothing’s thermal properties reduce heat dissipation. This study aimed to evaluate the heat strain encountered wearing EOD protective clothing in simulated environmental extremes across a range of differing work intensities. Eight healthy males [age 25±6 years (mean ± sd), height 180±7 cm, body mass 79±9 kg, V˙O2max 57±6 ml.kg−1.min−1] undertook nine trials while wearing an EOD9 suit (weighing 33.4 kg). The trials involved walking on a treadmill at 2.5, 4 and 5.5 km⋅h−1 at each of the following environmental conditions, 21, 30 and 37°C wet bulb globe temperature (WBGT) in a randomised controlled crossover design. The trials were ceased if the participants’ core temperature reached 39°C, if heart rate exceeded 90% of maximum, if walking time reached 60 minutes or due to fatigue/nausea. Tolerance times ranged from 10–60 minutes and were significantly reduced in the higher walking speeds and environmental conditions. In a total of 15 trials (21%) participants completed 60 minutes of walking; however, this was predominantly at the slower walking speeds in the 21°C WBGT environment. Of the remaining 57 trials, 50 were ceased, due to attainment of 90% maximal heart rate. These near maximal heart rates resulted in moderate-high levels of physiological strain in all trials, despite core temperature only reaching 39°C in one of the 72 trials.