Non-invasive method for detecting changes in soil moisture using wireless sensor networks

There are several popular soil moisture measurement methods today such as time domain reflectometry, electromagnetic (EM) wave, electrical and acoustic methods. Significant studies have been dedicated in developing method of measurements using those concepts, especially to achieve the characteristics of noninvasiveness. EM wave method provides an advantage because it is non-invasive to the soil and does not need to utilise probes to penetrate or bury in the soil. But some EM methods are also too complex, expensive, and not portable for the application of Wireless Sensor Networks; for example satellites or UAV (Unmanned Aerial Vehicle) based sensors. This research proposes a method in detecting changes in soil moisture using soil-reflected electromagnetic (SREM) wave from Wireless Sensor Networks (WSNs). Studies have shown that different levels of soil moisture will affects soil’s dielectric properties, such as relative permittivity and conductivity, and in turns change its reflection coefficients. The SREM wave method uses a transmitter adjacent to a WSNs node with purpose exclusively to transmit wireless signals that will be reflected by the soil. The strength from the reflected signal that is determined by the soil’s reflection coefficients is used to differentiate the level of soil moisture. The novel nature of this method comes from using WSNs communication signals to perform soil moisture estimation without the need of external sensors or invasive equipment. This innovative method is non-invasive, low cost and simple to set up. There are three locations at Brisbane, Australia chosen as the experiment’s location. The soil type in these locations contains 10–20% clay according to the Australian Soil Resource Information System. Six approximate levels of soil moisture (8, 10, 13, 15, 18 and 20%) are measured at each location; with each measurement consisting of 200 data. In total 3600 measurements are completed in this research, which is sufficient to achieve the research objective, assessing and proving the concept of SREM wave method. These results are compared with reference data from similar soil type to prove the concept. A fourth degree polynomial analysis is used to generate an equation to estimate soil moisture from received signal strength as recorded by using the SREM wave method.

Characteristics of the Internet for Criminal Child Sexual Abuse by Online Groomers

This paper presents a number of characteristics of the Internet that makes it attractive to online groomers. Relevant Internet characteristics include disconnected personal communication, mediating technology, universality, network externalities, distribution channel, time moderator, low‐cost standard, electronic double, electronic double manipulation, information asymmetry, infinite virtual capacity, independence in time and space, cyberspace, and dynamic social network. Potential sex offenders join virtual communities, where they meet other persons who have the same interest. A virtual community provides an online meeting place where people with similar interests can communicate and find useful information. Communication between members may be via email, bulletin boards, online chat, web‐based conferencing or other computer‐based media.

Linear and nonlinear propagation of localised plasmon in metallic nanostructures

A major challenge in modern photonics and nano-optics is the diffraction limit of light which does not allow field localisation into regions with dimensions smaller than half the wavelength. Localisation of light into nanoscale regions (beyond its diffraction limit) has applications ranging from the design of optical sensors and measurement techniques with resolutions as high as a few nanometres, to the effective delivery of optical energy into targeted nanoscale regions such as quantum dots, nano-electronic and nano-optical devices. This field has become a major research direction over the last decade. The use of strongly localised surface plasmons in metallic nanostructures is one of the most promising approaches to overcome this problem. Therefore, the aim of this thesis is to investigate the linear and non-linear propagation of surface plasmons in metallic nanostructures. This thesis will focus on two main areas of plasmonic research –– plasmon nanofocusing and plasmon nanoguiding. Plasmon nanofocusing – The main aim of plasmon nanofocusing research is to focus plasmon energy into nanoscale regions using metallic nanostructures and at the same time achieve strong local field enhancement. Various structures for nanofocusing purposes have been proposed and analysed such as sharp metal wedges, tapered metal films on dielectric substrates, tapered metal rods, and dielectric V-grooves in metals. However, a number of important practical issues related to nanofocusing in these structures still remain unclear. Therefore, one of the main aims of this thesis is to address two of the most important of issues which are the coupling efficiency and heating effects of surface plasmons in metallic nanostructures. The method of analysis developed throughout this thesis is a general treatment that can be applied to a diversity of nanofocusing structures, with results shown here for the specific case of sharp metal wedges. Based on the geometrical optics approximation, it is demonstrated that the coupling efficiency from plasmons generated with a metal grating into the nanofocused symmetric or quasi-symmetric modes may vary between ~50% to ~100% depending on the structural parameters. Optimal conditions for nanofocusing with the view to minimise coupling and dissipative losses are also determined and discussed. It is shown that the temperature near the tip of a metal wedge heated by nanosecond plasmonic pulses can increase by several hundred degrees Celsius. This temperature increase is expected to lead to nonlinear effects, self-influence of the focused plasmon, and ultimately self-destruction of the metal tip. This thesis also investigates a different type of nanofocusing structure which consists of a tapered high-index dielectric layer resting on a metal surface. It is shown that the nanofocusing mechanism that occurs in this structure is somewhat different from other structures that have been considered thus far. For example, the surface plasmon experiences significant backreflection and mode transformation at a cut-off thickness. In addition, the reflected plasmon shows negative refraction properties that have not been observed in other nanofocusing structures considered to date. Plasmon nanoguiding – Guiding surface plasmons using metallic nanostructures is important for the development of highly integrated optical components and circuits which are expected to have a superior performance compared to their electronicbased counterparts. A number of different plasmonic waveguides have been considered over the last decade including the recently considered gap and trench plasmon waveguides. The gap and trench plasmon waveguides have proven to be difficult to fabricate. Therefore, this thesis will propose and analyse four different modified gap and trench plasmon waveguides that are expected to be easier to fabricate, and at the same time acquire improved propagation characteristics of the guided mode. In particular, it is demonstrated that the guided modes are significantly screened by the extended metal at the bottom of the structure. This is important for the design of highly integrated optics as it provides the opportunity to place two waveguides close together without significant cross-talk. This thesis also investigates the use of plasmonic nanowires to construct a Fabry-Pérot resonator/interferometer. It is shown that the resonance effect can be achieved with the appropriate resonator length and gap width. Typical quality factors of the Fabry- Pérot cavity are determined and explained in terms of radiative and dissipative losses. The possibility of using a nanowire resonator for the design of plasmonic filters with close to ~100% transmission is also demonstrated. It is expected that the results obtained in this thesis will play a vital role in the development of high resolution near field microscopy and spectroscopy, new measurement techniques and devices for single molecule detection, highly integrated optical devices, and nanobiotechnology devices for diagnostics of living cells.

Composing maternal identities : the living realities of mothers with young adult-children in twenty-first century Australia

There is an abundance of books available on the topic of motherhood and mothering; the majority of these books focus on the vulnerability of babies and young children and the motherwork such vulnerability demands. In particular they focus on what it is right to do in the interests of the child, and particularly his or her growth and development. Such a focus is consistent in Western culture with modern moral frameworks where understandings of goodness have been assimilated to dimensions of human action rather than dimensions of human being, selfhood, or specific forms of life. As Charles Taylor has observed, much modern moral philosophy has focused =on what it is right to do rather than the nature of the good life‘ (1989, 13). The master narratives of motherhood and the prevailing social discourses of intensive1 and sacrificial2 mothering exemplify this view as such narratives and discourses depict =what mothers are expected to do [and] how mothers are supposed to be‘ (Nelson 2001, 140). From such infant/child-focused accounts a canonical maternal identity can be discerned; arguably, it is a restricted one. The majority of these books fail to address questions related to what it means be a mother in particular situated, existing, living realities. For instance, ask a mother with young children what being a mother means to her and she may speak of the challenges she faces balancing paid employment and her role as a mother, or the impact of the demands being made on her time and energy. However, ask a mother with young adult-children3 what being a mother means to her and she may speak in similar tones, but she may also speak in differing tones. For example, a "mature" mother may speak of the "empty nest", the "crowded house" and/or "its revolving front door". She may speak of issues related to the vulnerability of the long term marriage, elder care, or grandparenting, or even disillusionment and disenchantment. The purpose of this research is to explore the identity challenges and prospects of some mothers with young adult-children aged between 18 and 30 years of age in twenty-first century Australia. In interpreting the identity challenges and prospects this particular cohort of mothers encounter in their ordinary, everyday living, a diverse and particular range of maternal experiences.my own included5.have been traced, along with the social and ethical meanings ascribed in them. With an understanding and appreciation of voice as the medium which connects one's inner and outer worlds, this research illuminates the plurality of voices and the multiple layers of meaning in each of these mother's particular living and existing realities. Specifically, this research addresses the narrowly constructed, canonical maternal identity through a critical exploration and reflection on stories, shared in a research context, of the living realities of a group of self-identified "mature", middle-class, Australian mothers with children aged between 18 and 30 years of age6. By appraising the broader familial, historical, social, cultural, institutional, and, importantly, moral contexts in which these mothers are situated, 'thick descriptions' (Geertz 1973, 27)7 of maternal identities, and the challenges and prospects these mothers are negotiating, are provided. In terms of its ethical orientation, the frameworks which support and frame this research reject, repudiate and contest (Nelson 2001) the reduction of ethical concerns to individual or intellectual problems or dilemmas to be solved through the application of a theory derived from reasoned thinking. In dismissing deductive and =theoretical-juridical‘8 approaches, the individualistic orientation entrenched in contemporary Western moral thinking, expressed in the notion of '"what ought I to do" when faced with a problem, issue or dilemma of practical urgency' (Isaacs & Massey 1994, 1), is simultaneously rejected, repudiated and contested (Nelson 2001). In countering such understandings, this research reorients us to the illumination and articulation of who it is good to be, for each of these mothers, in allegiance with those goods which guide and inspire her orientations towards living a good life—a life which embraces and enhances the flourishing of herself and her significant others. With an understanding and appreciation that 'mind is never free of precommitment[—t]here is no innocent eye, nor is there one that penetrates aboriginal reality' (Bruner 1987, 32), this thesis is written with the voices of other interlocutors9. These interlocutors include the voices of my research participants whom I refer to as "research interlocutors", my textual "friends" — those scholars whose work resonates strongly with my orientations—as well as the myriad other voices that speak to mothers, for mothers and about mothers, such as those found in popular and mainstream press and culture. Sometimes these voices resonate; other times dissonance may be heard. In situating this research within these complementary frameworks, this research invites readers to join with me in considering, appreciating and appraising the narrow construction of maternal identity. I seek for this engagement, like the engagements with my research interlocutors, to be 'a meeting of voices, an authentic dialogue that is inclusive of the voices of all concerned participants' (Isaacs 2001, 6). I hope that the voices in this thesis resonate with yours (although, at times, you may feel some dissonance) and that together we can draw closer to the accounting, re-counting and re-stor(y)ing of maternal identities; like concentric circles of witness, the dialogue, ...will thus be expanded rippling into corners where one might both imagine, and least expect. Possibilities, then, are vast; the future exciting (Smith 2007, 397). This research is also shaped and guided by maternal scholarship, a relatively new field of inquiry known as 'motherhood studies' (O'Reilly 2011, xvii) which has its origins within the broader terrain of feminist scholarship. As a work of maternal scholarship, this thesis draws upon and continues the tradition of examining motherhood as it is experienced 'in a social context, as embedded in a political institution: in feminist terms' (Rich 1995, ix). It values mothers, their experiences, their stories, their lives. As such, this research is oriented towards 'matricentric feminism', a particular form of feminist inquiry, politics and theory which is consistent with and receptive to feminist frameworks of care and equal rights (O‘Reilly 2011, 25). A number of complementary conceptual frameworks have been engaged in this research with the thesis presented in three parts: the pre-figurative, configurative and re-configurative. As my particular living experiences provided the initial motivation for this research, an account of the challenges I experienced as a mother with young adult-children are outlined as a Prelude to this thesis. Attention then turns to Part One – Pre-figuring Maternal Identities in which the contextual, conceptual and methodological foundations underpinning this research are explored and outlined. In Chapter One, the prevailing cultural narratives and social discourses supporting and shaping the construction of the canonical maternal identity are outlined. Next, in setting the scholarly context, the critiques — arising from feminist and maternal scholarship — of motherhood as a patriarchal institution, mothering as experience, and mothering as work, are explored. As this research engaged with participants who are embedded in particular middle-class, heterosexual, familial and cultural structures, an exploration of family life cycle theory and main stream media accounts are also incorporated. The terrain in which "mature" mothering within an Australian context is experienced is also outlined, including the notions of "empty nests" and "crowded houses", grandparenting, elder care and women's midlife transition. Chapter Two gives an account of the conceptual ontological, ethical, identity and narrative frameworks underpinning this research. In setting the context for rich interpretations, the characteristics of being human10 are outlined before attention turns to our embodiment and embeddedness in our shared human condition11. From this point, attention then turns to understanding the moral form of human living12. In appreciating the vulnerability inherent in our shared human condition, the ways in which we may experience trouble in our lives is noted. The framing of identity constitution13 as complex, multi-faceted, relationally negotiated and composed is then outlined, followed by an understanding of why narrative is a valuable interpretive tool for interpreting and understanding human experiences. This chapter concludes with an appreciation of the ethical significance of storytelling. The research methodology is then outlined in Chapter Three. The rationale underpinning the adoption of the narrative interviewing technique of in-depth interviewing is explored. In exploring these methodological frameworks, the recruitment and interview processes involved in gathering and interpreting the recorded transcripts of ten Australian mothers with young adult-children are outlined. The method of analysis known as the Listening Guide14 best complements the multi-layered, pluri-vocal nature of narrative accounting. The final section of Chapter Three outlines The Guide, with one mother's recorded transcript used to illustrate this method's step-by-step process. Having gathered an understanding and appreciation of the pluri-vocal, multi-layered nature of narrative and identity constitution, the tone of this thesis changes in Part Two . Configuring Maternal Identities. This section consists of Chapters Four and Five and seeks to find meaning in, and make sense of, the differences and commonalities across these particular accounts. Chapter Four explores the living realities of four Australian mothers with young adult-children: Poppy, Honey, Lily and Heather. In presenting a thick description of these mothers' situated realities, the frameworks.the familial, social, cultural, historical and institutional backgrounds.which have supported and shaped each mother's experiences are illuminated. Simultaneously revealed through these particular accounts are the plurality of goods focusing and moving each mother to the moral form of life, a life of meaning and purpose. The harms challenging some mothers' moral motivations are also revealed in this chapter. Specifically illustrated in Chapter Four are the unique and qualitative differences of particular maternal identity configurations. Chapter Five reveals the commonalities amongst all of the research interlocutors' accounts. This chapter contests the individualistic orientation of many contemporary accounts of motherhood which are aimed at defining or contesting what a "good" mother ought to do. By turning away from such individualistic orientations, the chapter does not seek to define 'the content of obligation' (Taylor 1989, 3) but rather seeks to illuminate and articulate a richer, deeper understanding and appreciation of maternal be-ing and be-coming - that is, who it is good to be, for each of these mothers - in allegiance with those goods that focus and inspire her moral motivations. Part Three - Re-Configuring Maternal Identities, which is comprised of Chapter Six, draws this thesis to a close. In this final chapter, the preconceptions, conditions and aspirations for this mother-centred account of the living realities of a small, local cohort of mothers are reiterated. The insights gathered from the rich, descriptive accounts are illuminated and articulated, and the chapter closes with some suggestions for future research. In a Postlude, I reflect on how this research has been a transformative learning experience in my own life.an experience in which I have been able to not only deeply understand and appreciate the challenges and disorientation I was experiencing but also to identify and reorient my stance in relation to the good. In a practical sense, by offering thick descriptions of the living realities of this cohort of "mature" mothers, this research challenges the canonical maternal identity and questions its relevance for, and effect on, "mature" mothers' identity constitution. By bringing to light the complex existing realities of these particular mothers, this research critiques the canonical maternal identity by illustrating that each mother's life and her identity constitutions are complex, relationally negotiated and composed and that motherhood is an enduring way of being. Through these illustrations, this research engages with and extends understandings of difference feminism. This research, however, not only rejects, repudiates and contests (Nelson 2001) the narrowly defined canonical maternal identity. By illuminating and articulating the goods which shape and inspire these "mature" mothers' motherwork, this research offers a matricentric account which is consistent with and respectful of the particular, situated realities—the broader familial, social, institutional, but most importantly, moral values and frameworks—in which each mother‘s life is embedded and her motherwork oriented. By understanding and appreciating the complex and multiple webs of relationships in which each mother exists, this matricentric re-stor(y)ing of maternal experiences not only understands and appreciates the unique nature of each mother‘s existing realities, it is oriented to the continuing enhancing of the shared pursuit of the good which underpins particular maternal practices and particular maternal ways of being.

Experimental studies of the shear behavior and strength of LiteSteel beams with stiffened web openings

Abstract: LiteSteel beam (LSB) is a new cold-formed steel hollow flange channel section produced using a patented manufacturing process. It is commonly used as flexural members in residential, industrial and commercial buildings. Current practice in flooring systems is to include openings in the web element of floor joists or bearers so that building services can be located within them. Test results have shown that the shear capacity of LSBs can be reduced considerably by the inclusion of web openings. A cost effective method of eliminating the detrimental effects of a large web opening is to attach suitable stiffeners around the web openings of LSBs. A detailed experimental study consisting of 17 shear tests was therefore undertaken to investigate the shear behaviour and strength of LSBs with stiffened circular web openings. Both plate and stud stiffeners with varying sizes and thicknesses were attached to the web elements of LSBs using a number of screw-fastening arrangements in order to develop a suitable stiffening arrangement for LSBs. Simply supported test specimens of LSBs with an aspect ratio of 1.5 were loaded at mid-span until failure. This paper presents the details of this experimental study of LSBs with stiffened web openings, and the results of their shear capacities and associated behavioural characteristics. Suitable screw-fastened plate stiffener arrangements have been recommended in order to restore the original shear capacity of LSBs.

Influence of drying conditions on the moisture diffusion during single stage and two stage fluidized bed drying of bovine intestine for pet food

Bovine intestine samples were heat pump fluidized bed dried at atmospheric pressure and at temperatures below and above the material freezing points equipped with a continuous monitoring system. The investigation of the drying characteristics has been conducted in the temperature range -10~25oC and the airflow in the range 1.5~2.5 m/s. Some experiments were conducted as a single temperature drying experiments and others as two stage drying experiments employing two temperatures. An Arrhenius-type equation was used to interpret the influence of the drying air parameters on the effective diffusivity, calculated with the method of slopes in terms of energy activation, and this was found to be sensitivity of the temperature. The effective diffusion coefficient of moisture transfer was determined by Fickian method using uni-dimensional moisture movement in both moisture, removal by evaporation and combined sublimation and evaporation. Correlations expressing the effective moisture diffusivity and drying temperature are reported.

Evaluation of the Suchey-Brooks method for aging Australian Caucasian Populations using multislice Computed Tomography reconstructions of the Pubic Symphyseal Surface

Establishing age-at-death for skeletal remains is a vital component of forensic anthropology. The Suchey-Brooks (S-B) method of age estimation has been widely utilised since 1986 and relies on a visual assessment of the pubic symphyseal surface in comparison to a series of casts. Inter-population studies (Kimmerle et al., 2005; Djuric et al., 2007; Sakaue, 2006) demonstrate limitations of the S-B method, however, no assessment of this technique specific to Australian populations has been published. Aim: This investigation assessed the accuracy and applicability of the S-B method to an adult Australian Caucasian population by highlighting error rates associated with this technique. Methods: Computed tomography (CT) and contact scans of the S-B casts were performed; each geometrically modelled surface was extracted and quantified for reference purposes. A Queensland skeletal database for Caucasian remains aged 15 – 70 years was initiated at the Queensland Health Forensic and Scientific Services – Forensic Pathology Mortuary (n=350). Three-dimensional reconstruction of the bone surface using innovative volume visualisation protocols in Amira® and Rapidform® platforms was performed. Samples were allocated into 11 sub-sets of 5-year age intervals and changes associated with the surface geometry were quantified in relation to age, gender and asymmetry. Results: Preliminary results indicate that computational analysis was successfully applied to model morphological surface changes. Significant differences in observed versus actual ages were noted. Furthermore, initial morphological assessment demonstrates significant bilateral asymmetry of the pubic symphysis, which is unaccounted for in the S-B method. These results propose refinements to the S-B method, when applied to Australian casework. Conclusion: This investigation promises to transform anthropological analysis to be more quantitative and less invasive using CT imaging. The overarching goal contributes to improving skeletal identification and medico-legal death investigation in the coronial process by narrowing the range of age-at-death estimation in a biological profile.

Comparison of genomic DNA extraction techniques from whole blood samples : a time, cost and quality evaluation study

Genomic DNA obtained from patient whole blood samples is a key element for genomic research. Advantages and disadvantages, in terms of time-efficiency, cost-effectiveness and laboratory requirements, of procedures available to isolate nucleic acids need to be considered before choosing any particular method. These characteristics have not been fully evaluated for some laboratory techniques, such as the salting out method for DNA extraction, which has been excluded from comparison in different studies published to date. We compared three different protocols (a traditional salting out method, a modified salting out method and a commercially available kit method) to determine the most cost-effective and time-efficient method to extract DNA. We extracted genomic DNA from whole blood samples obtained from breast cancer patient volunteers and compared the results of the product obtained in terms of quantity (concentration of DNA extracted and DNA obtained per ml of blood used) and quality (260/280 ratio and polymerase chain reaction product amplification) of the obtained yield. On average, all three methods showed no statistically significant differences between the final result, but when we accounted for time and cost derived for each method, they showed very significant differences. The modified salting out method resulted in a seven- and twofold reduction in cost compared to the commercial kit and traditional salting out method, respectively and reduced time from 3 days to 1 hour compared to the traditional salting out method. This highlights a modified salting out method as a suitable choice to be used in laboratories and research centres, particularly when dealing with a large number of samples.

Comparative study on the protective effects of Yinchenhao Decoction against liver injury induced by alpha-naphthylisothiocyanate and carbon tetrachloride

OBJECTIVE: To optimize the animal model of liver injury that can properly represent the pathological characteristics of dampness-heat jaundice syndrome of traditional Chinese medicine. METHODS: The liver injury in the model rat was induced by alpha-naphthylisothiocyanate (ANIT) and carbon tetrachloride (CCl(4) ) respectively, and the effects of Yinchenhao Decoction (, YCHD), a proved effective Chinese medical formula for treating the dampness-heat jaundice syndrome in clinic, on the two liver injury models were evaluated by analyzing the serum level of alanine aminotransferase (ALT), asparate aminotransferase (AST), alkaline phosphatase (ALP), malondialchehyche (MDA), total bilirubin (T-BIL), superoxide dismutase (SOD), glutathione peroxidase (GSH-PX) as well as the ratio of liver weight to body weight. The experimental data were analyzed by principal component analytical method of pattern recognition. RESULTS: The ratio of liver weight to body weight was significantly elevated in the ANIT and CCl(4) groups when compared with that in the normal control (P<0.01). The contents of ALT and T-BIL were significantly higher in the ANIT group than in the normal control (P<0.05,P<0.01), and the levels of AST, ALT and ALP were significantly elevated in CCl(4) group relative to those in the normal control P<0.01). In the YCHD group, the increase in AST, ALT and ALP levels was significantly reduced (P<0.05, P<0.01), but with no significant increase in serum T-BIL. In the CCl(4) intoxicated group, the MDA content was significantly increased and SOD, GSH-PX activities decreased significantly compared with those in the normal control group, respectively (P<0.01). The increase in MDA induced by CCl(4) was significantly reduced by YCHD P<0.05). CONCLUSION: YCHD showed significant effects on preventing liver injury progression induced by CCl(4), and the closest or most suitable animal model for damp-heat jaundice syndrome may be the one induced by CCl(4).

Method for the production of porous complex metal oxides using a porogen

A method of producing porous complex oxides includes the steps of providing a mixt. of (a) precursor elements suitable to produce the complex oxide, or (b) one or more precursor elements suitable to produce particles of the complex oxide and one or more metal oxide particles; and (c) a particulate carbon-contg. pore-forming material selected to provide pore sizes in the range of 7-250 nm, and treating the mixt. to (i) form the porous complex oxide in which two or more of the precursor elements from (a) above or one or more of the precursor elements and one or more of the metals in the metal oxide particles from (b) above are incorporated into a phase of the complex metal oxide and the complex metal oxide has grain sizes in the range of 1-150 nm, and (ii) removing the pore-forming material under conditions such that the porous structure and compn. of the complex oxide is substantially preserved. The method may be used to produce nonrefractory metal oxides as well. The mixt. further includes a surfactant, or a polymer. [on SciFinder(R)]

Influence of drying conditions on the moisture diffusion and fluidization quality during multi-stage fluidized bed drying of bovine intestine for pet food

In order to establish the influence of the drying air characteristics on the drying performance and fluidization quality of bovine intestine for pet food, several drying tests have been carried out in a laboratory scale heat pump assisted fluid bed dryer. Bovine intestine samples were heat pump fluidized bed dried at atmospheric pressure and at temperatures below and above the materials freezing points, equipped with a continuous monitoring system. The investigation of the drying characteristics have been conducted in the temperature range −10 to 25 ◦C and the airflow in the range 1.5–2.5 m/s. Some experiments were conducted as single temperature drying experiments and others as two stage drying experiments employing two temperatures. An Arrhenius-type equation was used to interpret the influence of the drying air temperature on the effective diffusivity, calculated with the method of slopes in terms of energy activation, and this was found to be sensitive to the temperature. The effective diffusion coefficient of moisture transfer was determined by the Fickian method using uni-dimensional moisture movement in both moisture, removal by evaporation and combined sublimation and evaporation. Correlations expressing the effective moisture diffusivity and drying temperature are reported. Bovine particles were characterized according to the Geldart classification and the minimum fluidization velocity was calculated using the Ergun Equation and generalized equation for all drying conditions at the beginning and end of the trials. Walli’s model was used to categorize stability of the fluidization at the beginning and end of the dryingv for each trial. The determined Walli’s values were positive at the beginning and end of all trials indicating stable fluidization at the beginning and end for each drying condition.

Fully validated LC–MS/MS method for quantification of homocysteine concentrations in samples of human serum : a new approach

Reported homocysteine (HCY) concentrations in human serum show poor concordance amongst laboratories due to endogenous HCY in the matrices used for assay calibrators and QCs. Hence, we have developed a fully validated LC–MS/MS method for measurement of HCY concentrations in human serum samples that addresses this issue by minimising matrix effects. We used small volumes (20 μL) of 2% Bovine Serum Albumin (BSA) as surrogate matrix for making calibrators and QCs with concentrations adjusted for the endogenous HCY concentration in the surrogate matrix using the method of standard additions. To aliquots (20 μL) of human serum samples, calibrators or QCs, were added HCY-d4 (internal standard) and tris-(2-carboxyethyl) phosphine hydrochloride (TCEP) as reducing agent. After protein precipitation, diluted supernatants were injected into the LC–MS/MS. Calibration curves were linear; QCs were accurate (5.6% deviation from nominal), precise (CV% ≤ 9.6%), stable for four freeze–thaw cycles, and when stored at room temperature for 5 h or at −80 °C (27 days). Recoveries from QCs in surrogate matrix or pooled human serum were 91.9 and 95.9%, respectively. There was no matrix effect using 6 different individual serum samples including one that was haemolysed. Our LC–MS/MS method has satisfied all of the validation criteria of the 2012 EMA guideline.

A micro-level investigation of the solid displacement method for porosity determination of dried food

Porosity is one of the key parameters of the macroscopic structure of porous media, generally defined as the ratio of the free spaces occupied (by the volume of air) within the material to the total volume of the material. Porosity is determined by measuring skeletal volume and the envelope volume. Solid displacement method is one of the inexpensive and easy methods to determine the envelope volume of a sample with an irregular shape. In this method, generally glass beads are used as a solid due to their uniform size, compactness and fluidity properties. The smaller size of the glass beads means that they enter into the open pores which have a larger diameter than the glass beads. Although extensive research has been carried out on porosity determination using displacement method, no study exists which adequately reports micro-level observation of the sample during measurement. This study set out with the aim of assessing the accuracy of solid displacement method of bulk density measurement of dried foods by micro-level observation. Solid displacement method of porosity determination was conducted using a cylindrical vial (cylindrical plastic container) and 57 µm glass beads in order to measure the bulk density of apple slices at different moisture contents. A scanning electron microscope (SEM), a profilometer and ImageJ software were used to investigate the penetration of glass beads into the surface pores during the determination of the porosity of dried food. A helium pycnometer was used to measure the particle density of the sample. Results show that a significant number of pores were large enough to allow the glass beads to enter into the pores, thereby causing some erroneous results. It was also found that coating the dried sample with appropriate coating material prior to measurement can resolve this problem.

Morphogenetic analysis of architectural elements within the townscape

When a new form is inserted in an existing townscape, its consonance within the urban fabric is dependent on the level of attention paid to the evaluation and management of its architectural elements. However, despite the established principles and methods of urban morphology that enable the systematic analysis of the built environment, a formula for ensuring that new development relates to its context so as to achieve congruent outcomes is still lacking. This paper proposes a new method of evaluating and measuring architectural elements within evolving urban forms, with particular emphasis on a three-dimensional study of buildings. In a case study, detailed mapping of both current and past forms provides the basis for evincing predominant characteristics that have changed over time. Using this method, it is possible to demonstrate objectively how the townscape has been affected through changes in its architectural configuration.

Validation of a partial coherence interferometry method for estimating retinal shape

To validate a simple partial coherence interferometry (PCI) based retinal shape method, estimates of retinal shape were determined in 60 young adults using off-axis PCI, with three stages of modeling using variants of the Le Grand model eye, and magnetic resonance imaging (MRI). Stage 1 and 2 involved a basic model eye without and with surface ray deviation, respectively and Stage 3 used model with individual ocular biometry and ray deviation at surfaces. Considering the theoretical uncertainty of MRI (12-14%), the results of the study indicate good agreement between MRI and all three stages of PCI modeling with <4% and <7% differences in retinal shapes along horizontal and vertical meridians, respectively. Stage 2 and Stage 3 gave slightly different retinal co-ordinates than Stage 1 and we recommend the intermediate Stage 2 as providing a simple and valid method of determining retinal shape from PCI data.