An investigation of commuter exposure to ultrafine particles in Sydney

Commuting in various transport modes represents an activity likely to incur significant exposure to traffic emissions. This study investigated the determinants and characteristics of exposure to ultrafine (< 100 nm) particles (UFPs) in four transport modes in Sydney, with a specific focus on exposure in automobiles, which remain the transport mode of choice for approximately 70% of Sydney commuters. UFP concentrations were measured using a portable condensation particle counter (CPC) inside five automobiles commuting on above ground and tunnel roadways, and in buses, ferries and trains. Determinant factors investigated included wind speed, cabin ventilation (automobiles only) and traffic volume. The results showed that concentrations varied significantly as a consequence of transport mode, vehicle type and ventilation characteristics. The effects of wind speed were minimal relative to those of traffic volume (especially heavy diesel vehicles) and cabin ventilation, with the latter proving to be a strong determinant of UFP ingress into automobiles. The effect of ~70 minutes of commuting on total daily exposure was estimated using a range of UFP concentrations reported for several microenvironments. A hypothetical Sydney resident commuting by automobile and spending 8.5 minutes of their day in the M5 East tunnel could incur anywhere from a lower limit of 3-11% to an upper limit of 37-69% of daily UFP exposure during a return commute, depending on the concentrations they encountered in other microenvironments, the type of vehicle they used and the ventilation setting selected. However, commute-time exposures at either extreme of the values presented are unlikely to occur in practice. The range of exposures estimated for other transport modes were comparable to those of automobiles, and in the case of buses, higher than automobiles.

Chaos or complex systems? Identifying factors influencing the success of international and NESB graduate research students in Engineering and Information Technology Fields

The paper explores the results an on-going research project to identify factors influencing the success of international and non-English speaking background (NESB) gradúate students in the fields of Engineering and IT at three Australian universities: the Queensland University of Technology (QUT), the University of Western Australia (UWA), and Curtin University (CU). While the larger study explores the influence of factors from both sides of the supervision equation (e.g., students and supervisors), this paper focusses primarily on the results of an online survey involving 227 international and/or NESB graduate students in the areas of Engineering and IT at the three universities. The study reveals cross-cultural differences in perceptions of student and supervisor roles, as well as differences in the understanding of the requirements of graduate study within the Australian Higher Education context. We argue that in order to assist international and NESB research students to overcome such culturally embedded challenges, it is important to develop a model which recognizes the complex interactions of factors from both sides of the supervision relationship, in order to understand this cohort‟s unique pedagogical needs and develop intercultural sensitivity within postgraduate research supervision.

Digital complementary assets

Google, Facebook, Twitter, LinkedIn, etc. are some of the prominent large-scale digital service providers that are having tremendous impact on societies, corporations and individuals. However, despite the rapid uptake and their obvious influence on the behavior of individuals and the business models and networks of organizations, we still lack a deeper, theory-guided understanding of the related phenomenon. We use Teece’s notion of complementary assets and extend it towards ‘digital complementary assets’ (DCA) in an attempt to provide such a theory-guided understanding of these digital services. Building on Teece’s theory, we make three contributions. First, we offer a new conceptualization of digital complementary assets in the form of digital public goods and digital public assets. Second, we differentiate three models for how organizations can engage with such digital complementary assets. Third, user-base is found to be a critical factor when considering appropriability.

Regulations and policy measures related to the reduction of ambient particulate matter

-

Real estate issues associated with the implementation of a carbon trading framework : a rural landholders perspective

The issue of carbon sequestration rights has become topical following the United Nations Convention on Climate Change and the subsequent Kyoto Protocol which identified emissions trading as one of the mechanisms to reduce greenhouse gas emissions. The Australian Government has responded by initiating the Garnaut Climate Change Review which in its final report, proposed that an emissions trading scheme be introduced and set out some of the desirable features of such a trading scheme. This proposal has been the subject of much debate and at this stage there still seems to be little clarity surrounding the topic of emissions trading in Australia. The treatment of rights to carbon sequestered in vegetation is also an issue when reconciled with the system of land tenure and ownership in many jurisdictions. These carbon property rights are treated differently in different Australian and international jurisdictions ranging from recognition of their new and unique nature to fitting them within a more established common law framework, e.g.a profit a prendre. This paper identifies the treatment of these sequestered carbon rights within the wider property rights framework in Australia and considers issues that this treatment may inflict on land holders when there is a fracturing of ownership between the rights of the carbon in vegetation and the ownership of the land.

Identifying the extent, motivations and barriers to outsourcing of accounting services.

In this paper we analyse the oursourcing of accounting services. The extent to which firms are currently outsourcing, or considering outsourcing such services, and the motivations and barriers associated with outsourcing are identified. Empirical data from a random sample of accounting firms are used in this analysis. Data indicate that the majority of accounting firms are either currently outsourcing or considering outsourcing and that they exopect the volume of oursourced services to increase. In contrast to the scholarly literature advocating labor arbitrage as the primary driver for organizations choosing to outsource, in this study it was found that the main factors underpinning the decision to outsource were the expediting of service delivary to clients, and to enable the firm to focus on its core competencies.

Music selection using a touch screen interface : effect of auditory and visual feedback on driving and usability

This study aimed to examine the effects on driving, usability and subjective workload of performing music selection tasks using a touch screen interface. Additionally, to explore whether the provision of visual and/or auditory feedback offers any performance and usability benefits. Thirty participants performed music selection tasks with a touch screen interface while driving. The interface provided four forms of feedback: no feedback, auditory feedback, visual feedback, and a combination of auditory and visual feedback. Performance on the music selection tasks significantly increased subjective workload and degraded performance on a range of driving measures including lane keeping variation and number of lane excursions. The provision of any form of feedback on the touch screen interface did not significantly affect driving performance, usability or subjective workload, but was preferred by users over no feedback. Overall, the results suggest that touch screens may not be a suitable input device for navigating scrollable lists.

Field study of air change and flow rate in six automobiles

For many people, a relatively large proportion of daily exposure to a multitude of pollutants may occur inside an automobile. A key determinant of exposure is the amount of outdoor air entering the cabin (i.e. air change or flow rate). We have quantified this parameter in six passenger vehicles ranging in age from 18 years to <1 year, at three vehicle speeds and under four different ventilation settings. Average infiltration into the cabin with all operable air entry pathways closed was between 1 and 33.1 air changes per hour (ACH) at a vehicle speed of 60 km/h, and between 2.6 and 47.3 ACH at 110 km/h, with these results representing the most (2005 Volkswagen Golf) and least air-tight (1989 Mazda 121) vehicles, respectively. Average infiltration into stationary vehicles parked outdoors varied between ~0 and 1.4 ACH and was moderately related to wind speed. Measurements were also performed under an air recirculation setting with low fan speed, while airflow rate measurements were conducted under two non-recirculate ventilation settings with low and high fan speeds. The windows were closed in all cases, and over 200 measurements were performed. The results can be applied to estimate pollutant exposure inside vehicles.

Understanding evaluation of learning support in mathematics and statistics

With rapid and continuing growth of learning support initiatives in mathematics and statistics found in many parts of the world, and with the likelihood that this trend will continue, there is a need to ensure that robust and coherent measures are in place to evaluate the effectiveness of these initiatives. The nature of learning support brings challenges for measurement and analysis of its effects. After briefly reviewing the purpose, rationale for, and extent of current provision, this article provides a framework for those working in learning support to think about how their efforts can be evaluated. It provides references and specific examples of how workers in this field are collecting, analysing and reporting their findings. The framework is used to structure evaluation in terms of usage of facilities, resources and services provided, and also in terms of improvements in performance of the students and staff who engage with them. Very recent developments have started to address the effects of learning support on the development of deeper approaches to learning, the affective domain and the development of communities of practice of both learners and teachers. This article intends to be a stimulus to those who work in mathematics and statistics support to gather even richer, more valuable, forms of data. It provides a 'toolkit' for those interested in evaluation of learning support and closes by referring to an on-line resource being developed to archive the growing body of evidence. © 2011 Taylor & Francis.

Investing in the future : analysis of TxDOT 1547 Over-Axle Weight Tolerance Permits

The trucking industry has played a significant role in the economic growth in Texas by transporting and distributing commodities using commercial motor vehicles. The Texas Department of Transportation (TxDOT), however, has recognized that the large number of overweight trucks operating on the state highway system has resulted in the deterioration of pavement condition. In addition, the permit fee to carry higher loads above legal limits is much lower than the cost to treat the increase in pavement damage. The primary purpose of the research presented in this paper is to investigate current TxDOT overweight permit structures to support pavement management. The research team analyzed the TxDOT “1547” Over-axle Weight Tolerance Permit structure to support an increase in the fee structure, bringing it more in line with the actual pavement damage. The analysis showed that the revised overweight permit structure could provide an additional $9.3 million annually for pavement maintenance needs by increasing current permit fees. These results were supported by the 2030 Committee for recommendation to the Texas Transportation Commission and consideration by the State Legislature [1]. The research team recommends conducting further research to identify methods for working cooperatively with the trucking industry to develop improved methods for assessing weight damage relationships and developing more effective and accurate means for assessing overweight permit fees.

Peer state assessment of TxDOT maintenance program and practices, part II : test section survey findings and recommendations

This paper presents a road survey as part of a workshop conducted by the Texas Department of Transportation (TxDOT) to evaluate and improve the maintenance practices of the Texas highway system. Directors of maintenance from six peer states (California, Kansas, Georgia, Missouri, North Carolina, and Washington) were invited to this 3-day workshop. One of the important parts of this workshop was a Maintenance Test Section Survey (MTSS) to evaluate a number of pre-selected one-mile roadway sections. The workshop schedule allowed half a day to conduct the field survey and 34 sections were evaluated. Each of the evaluators was given a booklet and asked to rate the selected road sections. The goals of the MTSS were to: 1. Assess the threshold level at which maintenance activities are required as perceived by the evaluators from the peer states; 2. Assess the threshold level at which maintenance activities are required as perceived by evaluators from other TxDOT districts; and 3. Perform a pilot evaluation of the MTSS concept. This paper summarizes the information obtained from survey and discusses the major findings based on a statistical analysis of the data and comments from the survey participants.

Peer state assessment of TxDOT maintenance program and practices, part I : workshop findings and recommendations

To assess and improve their practices, and thus ensure the future excellence of the Texas highway system, the Texas Department of Transportation (TxDOT) sought a forum in which experts from other State Departments of Transportation could evaluate the TxDOT maintenance program and practices based on their expertise. To meet this need, a Peer State Review of TxDOT Maintenance Practices project was organized and conducted by the Center for Transportation Research (CTR) at The University of Texas at Austin. CTR researchers, along with TxDOT staff, conducted a workshop to present TxDOT’s maintenance practices to the visiting peer reviewers and invite their feedback. Directors of maintenance from six different states—California, Kansas, Georgia, Missouri, North Carolina, and Washington—participated in the workshop. CTR and TxDOT worked together to design a questionnaire with 15 key questions to capture the peers’ opinions on maintenance program and practices. This paper compiles and summarizes this information. The examination results suggested that TxDOT should use a more state-wide approach to funding and planning, in addition to funding and planning for each district separately. Additionally, the peers recommended that criteria such as condition and level of service of the roadways be given greater weight in the funding allocation than lane miles or vehicle miles traveled (VMT). The Peer Reviewers also determined that TxDOT maintenance employee experience and communications were strong assets. Additional strengths included the willingness of TxDOT to invite peer reviews of their practices and a willingness to consider opportunities for improvement.

Understanding user experience of mobile video : framework, measurement, and optimization

Since users have become the focus of product/service design in last decade, the term User eXperience (UX) has been frequently used in the field of Human-Computer-Interaction (HCI). Research on UX facilitates a better understanding of the various aspects of the user’s interaction with the product or service. Mobile video, as a new and promising service and research field, has attracted great attention. Due to the significance of UX in the success of mobile video (Jordan, 2002), many researchers have centered on this area, examining users’ expectations, motivations, requirements, and usage context. As a result, many influencing factors have been explored (Buchinger, Kriglstein, Brandt & Hlavacs, 2011; Buchinger, Kriglstein & Hlavacs, 2009). However, a general framework for specific mobile video service is lacking for structuring such a great number of factors. To measure user experience of multimedia services such as mobile video, quality of experience (QoE) has recently become a prominent concept. In contrast to the traditionally used concept quality of service (QoS), QoE not only involves objectively measuring the delivered service but also takes into account user’s needs and desires when using the service, emphasizing the user’s overall acceptability on the service. Many QoE metrics are able to estimate the user perceived quality or acceptability of mobile video, but may be not enough accurate for the overall UX prediction due to the complexity of UX. Only a few frameworks of QoE have addressed more aspects of UX for mobile multimedia applications but need be transformed into practical measures. The challenge of optimizing UX remains adaptations to the resource constrains (e.g., network conditions, mobile device capabilities, and heterogeneous usage contexts) as well as meeting complicated user requirements (e.g., usage purposes and personal preferences). In this chapter, we investigate the existing important UX frameworks, compare their similarities and discuss some important features that fit in the mobile video service. Based on the previous research, we propose a simple UX framework for mobile video application by mapping a variety of influencing factors of UX upon a typical mobile video delivery system. Each component and its factors are explored with comprehensive literature reviews. The proposed framework may benefit in user-centred design of mobile video through taking a complete consideration of UX influences and in improvement of mobile videoservice quality by adjusting the values of certain factors to produce a positive user experience. It may also facilitate relative research in the way of locating important issues to study, clarifying research scopes, and setting up proper study procedures. We then review a great deal of research on UX measurement, including QoE metrics and QoE frameworks of mobile multimedia. Finally, we discuss how to achieve an optimal quality of user experience by focusing on the issues of various aspects of UX of mobile video. In the conclusion, we suggest some open issues for future study.

Why perform pro-social behaviours? Understanding the key sources of perceived value in preventative health services

In maintaining quality of life, preventative health is an important area in which the performance of pro-social behaviours provides benefits to individuals who perform them as well as society. The establishment of the Preventative Health Taskforce in Australia demonstrates the significance of preventative health and aims to provide governments and health providers with evidence-based advice on preventative health issues (Preventative Health Taskforce, 2009). As preventative health behaviours are voluntary, for consumers to sustain this behaviour there needs to be a value proposition (Dann, 2008; Kotler and Lee, 2008). Customer value has been shown to influence repeat behaviour (McDougall and Levesque, 2000), word-of-mouth (Hartline and Jones, 1999), and attitudes (Dick and Basu, 2008). However to date there is little research that investigates the source of value for preventative health services. This qualitative study explores and identifies three categories of sources that influence four dimensions of value – functional, emotional, social and altruistic (Holbrook 2006). A conceptual model containing five propositions outlining these relationships is presented. This study provides evidence-based research that reveals sources of value that influence individuals’ decisions to perform pro-social behaviours in the long-term through their use of preventative health services. This research uses BreastScreen Queensland (BSQ), a cancer screening service, as the service context.

Home sustainability policy and mandatory disclosure. a survey of buyer and seller participation and awareness in Qld

Sustainability Declarations were introduced by the Queensland State Government on 1 January 2010 as a mandatory disclosure measure for all dwelling sales in the State. The purpose of this paper is to assess the impact this policy decision has had in the homebuyer decision-making process in the first year since its introduction and to consider the effectiveness of the legislation in meeting its policy objectives. This quantitative research comprised a two-part process: the first stage surveyed the level of compliance by the real estate industry with the legislative requirements. Stage two comprised an online survey of Real Estate Institute of Queensland members to determine what impact the Sustainability Declaration has had on home buyer decision making and how effective the legislative mechanisms have been in achieving the policy objectives. This paper assesses the initial impact of this initiative over its first year in operation. These preliminary findings indicate a high level of compliance from the real estate industry, however results confirm that sustainability is yet to become a criterion of relevance to the majority of homebuyers in Queensland. These quantitative findings support anecdotal evidence that the objectives of the legislation to increase homebuyer awareness and relevance of sustainability issues in the home are not being achieved. Sustainability Declarations are a first step in raising homebuyer awareness of the importance of sustainability in housing. Further monitoring of this impact will be carried out over time. This is the first research undertaken to assess the impact of this new mandatory disclosure legislation in Queensland, Australia. The findings will inform policy makers and assist them to assess the effectiveness of the current legislation in achieving its policy objectives.