Effect of recovery modality on 4-hour repeated treadmill running performance and changes in physiological variables

The purpose of this study was to compare the effectiveness of three different recovery modalities - active (ACT), passive (PAS) and contrast temperature water immersion (CTW) - on the performance of repeated treadmill running, lactate concentration and pH. Fourteen males performed two pairs of treadmill runs to exhaustion at 120% and 90% of peak running speed (PRS) over a 4-hour period. ACT, PAS or CTW was performed for 15-min after the first pair of treadmill runs. ACT consisted of running at 40% PRS, PAS consisted of standing stationary and CTW consisted of alternating between 60-s cold (10°C) and 120-s hot (42°C) water immersion. Run times were converted to time to cover set distance using critical power. Type of recovery modality did not have a significant effect on change in time to cover 400 m (Mean±SD; ACT 2.7±3.6 s, PAS 2.9±4.2 s, CTW 4.2±6.9 s), 1000 m (ACT 2.2±4.0 s, PAS 4.8±8.6 s, CTW 2.1±7.2 s) or 5000 m (ACT 1.4±29.0 s, PAS 16.7±58.5 s, CTW 11.7±33.0 s). Post exercise blood lactate concentration was lower in ACT and CTW compared with PAS. Participants reported an increased perception of recovery in the CTW compared with ACT and PAS. Blood pH was not significantly influenced by recovery modality. Data suggest both ACT and CTW reduce lactate accumulation after high intensity running, but high intensity treadmill running performance is returned to baseline 4-hours after the initial exercise bout regardless of the recovery strategy employed.

Effect of interval training intensity on fat oxidation, blood lactate and the rate of perceived exertion in obese men

Purpose The objectives of this study were to examine the effect of 4-week moderate- and high-intensity interval training (MIIT and HIIT) on fat oxidation and the responses of blood lactate (BLa) and rating of perceived exertion (RPE). Methods Ten overweight/obese men (age = 29 ±3.7 years, BMI = 30.7 ±3.4 kg/m2) participated in a cross-over study of 4-week MIIT and HIIT training. The MIIT training sessions consisted of 5-min cycling stages at mechanical workloads 20% above and 20% below 45%VO2peak. The HIIT sessions consisted of intervals of 30-s work at 90%VO2peak and 30-s rest. Pre- and post-training assessments included VO2max using a graded exercise test (GXT) and fat oxidation using a 45-min constant-load test at 45%VO2max. BLa and RPE were also measured during the constant-load exercise test. Results There were no significant changes in body composition with either intervention. There were significant increases in fat oxidation after MIIT and HIIT (p ≤ 0.01), with no effect of intensity. BLa during the constant-load exercise test significantly decreased after MIIT and HIIT (p ≤ 0.01), and the difference between MIIT and HIIT was not significant (p = 0.09). RPE significantly decreased after HIIT greater than MIIT (p ≤ 0.05). Conclusion Interval training can increase fat oxidation with no effect of exercise intensity, but BLa and RPE decreased after HIIT to greater extent than MIIT.

Effect of an adiabatic fin on natural convection heat transfer in a triangular enclosure

Natural convection thermal boundary layer adjacent to the heated inclined wall of a right angled triangle with an adiabatic fin attached to that surface is investigated by numerical simulations. The finite volume based unsteady numerical model is adopted for the simulation. It is revealed from the numerical results that the development of the boundary layer along the inclined surface is characterized by three distinct stages, i.e. a start-up stage, a transitional stage and a steady stage. These three stages can be clearly identified from the numerical simulations. Moreover, in presence of adiabatic fin, the thermal boundary layer adjacent to the inclined wall breaks initially. However, it is reattached with the downstream boundary layer next to the fin. More attention has been given to the boundary layer development near the fin area.

Communication models of institutional online communities : the role of the ABC cultural intermediary

The co-creation of cultural artefacts has been democratised given the recent technological affordances of information and communication technologies. Web 2.0 technologies have enabled greater possibilities of citizen inclusion within the media conversations of their nations. For example, the Australian audience has more opportunities to collaboratively produce and tell their story to a broader audience via the public service media (PSM) facilitated platforms of the Australian Broadcasting Corporation (ABC). However, providing open collaborative production for the audience gives rise to the problem, how might the PSM manage the interests of all the stakeholders and align those interests with its legislated Charter? This paper considers this problem through the ABC’s user-created content participatory platform, ABC Pool and highlights the cultural intermediary as the role responsible for managing these tensions. This paper also suggests cultural intermediation is a useful framework for other media organisations engaging in co-creative activities with their audiences.

The role of the cultural intermediary within professional participatory communication : lessons from ABC Pool

As media institutions are encouraged to explore new production methodologies in the current economic crisis, they align with Schumpeter’s creative destruction provocation by exhibiting user-led political, organisation and socio-technical innovations. This paper highlights the significance of the cultural intermediary within the innovative, co-creative production arrangements for cultural artefacts by media professionals in institutional online communities. An institutional online community is defined as one that is housed, resourced and governed by commercial or non- commercial institutions and is not independently facilitated. Web 2.0 technologies have mobilised collaborative peer production activities for online content creation and professional media institutions face challenges in engaging participatory audiences in practices that are beneficial for all concerned stakeholders. The interests of those stakeholders often do not align, highlighting the need for an intermediary role that understands and translates the norms, rhetoric tropes and day-to-day activities between the individuals engaging in participatory communication activities for successful negotiation within the production process. This paper specifically explores the participatory relationship between the public service broadcaster (PSB), the Australian Broadcasting Corporation (ABC) and one of its online communities, ABC Pool (www.abc.net.au/pool). ABC Pool is an online platform developed and resourced by the ABC to encourage co-creation between audience members engaging in the production of user-generated content (UGC) and the professional producers housed within the ABC Radio Division. This empirical research emerges from a three-year research project where I employed an ethnographic action research methodology and was embedded at the ABC as the community manager of ABC Pool. In participatory communication environments, users favour meritocratic heterarchical governance over traditional institutional hierarchical systems (Malaby 2009). A reputation environment based on meritocracy requires an intermediary to identify the stakeholders, understand their interests and communicate effectively between them to negotiate successful production outcomes (Bruns 2008; Banks 2009). The community manager generally occupies this role, however it has emerged that other institutional production environments also employ an intermediary role under alternative monikers(Hutchinson 2012). A useful umbrella term to encompass the myriad of roles within this space is the cultural intermediary. The ABC has experimented with three institutional online community governance models that engage in cultural intermediation in differing decentralised capacities. The first and most closed is a single point of contact model where one cultural intermediary controls all of the communication of the participatory project. The second is a model of multiple cultural intermediaries engaging in communication between the institutional online community stakeholders simultaneously. The third is most open yet problematic as it promotes and empowers community participants to the level of cultural intermediaries. This paper uses the ABC Pool case study to highlight the differing levels of openness within cultural intermediation during the co-creative production process of a cultural artifact.

Communication models of institutional online communities : the role of the ABC cultural intermediary

The co-creation of cultural artefacts has been democratised given the recent technological affordances of information and communication technologies. Web 2.0 technologies have enabled greater possibilities of citizen inclusion within the media conversations of their nations. For example, the Australian audience has more opportunities to collaboratively produce and tell their story to a broader audience via the public service media (PSM) facilitated platforms of the Australian Broadcasting Corporation (ABC). However, providing open collaborative production for the audience gives rise to the problem, how might the PSM manage the interests of all the stakeholders and align those interests with its legislated Charter? This paper considers this problem through the ABC’s user-created content participatory platform, ABC Pool and highlights the cultural intermediary as the role responsible for managing these tensions. This paper also suggests cultural intermediation is a useful framework for other media organisations engaging in co-creative activities with their audiences.

Effect of the mediator in feedback mode-based SECM interrogation of indium tin-oxide and boron-doped diamond electrodes

Indium tin-oxide (ITO) and polycrystalline boron-doped diamond (BDD) have been examined in detail using the scanning electrochemical microscopy technique in feedback mode. For the interrogation of electrodes made from these materials, the choice of mediator has been varied. Using Ru(CN) 4− 6 (aq), ferrocene methanol (FcMeOH), Fe(CN) 3− 6 (aq) and Ru(NH 3) 3+ 6 (aq), approach curve experiments have been performed, and for purposes of comparison, calculations of the apparent heterogeneous electron transfer rates (k app) have been made using these data. In general, it would appear that values of k app are affected mainly by the position of the mediator reversible potential relative to the relevant semiconductor band edge (associated with majority carriers). For both the ITO (n type) and BDD (p type) electrodes, charge transfer is impeded and values are very low when using FcMeOH and Fe(CN) 3− 6 (aq) as mediators, and the use of Ru(NH 3) 3+ 6(aq) results in the largest value of k app. With ITO, the surface is chemically homogeneous and no variation is observed for any given mediator. Data is also presented where the potential of the ITO electrode is fixed using a ratio of the mediators Fe(CN) 3− 6(aq) and Fe(CN) 4− 6(aq). In stark contrast, the BDD electrode is quite the opposite and a range of k app values are observed for all mediators depending on the position on the surface. Both electrode surfaces are very flat and very smooth, and hence, for BDD, variations in feedback current imply a variation in the electrochemical activity. A comparison of the feedback current where the substrate is biased and unbiased shows a surprising degree of proportionality.

A combined scanning electron micrograph and electrochemical study of the effect of chemical interaction on the cyclability of lithium electrodes in an ionic liquid electrolyte

The effect of storage time on the cyclability of lithium electrodes in an ionic liquid electrolyte, namely 0.5 m LiBF4 in N-methyl-N-propyl pyrrolidinium bis(fluorosulfonyl)imide, [C3mpyr+][FSI–], was investigated. A chemical interaction was observed which is time dependent and results in a morphology change of the Li surface due to build up of passivation products over a 12-day period. The formation of this layer significantly impacts on the Li electrode resistance before cycling and the charging/discharging process for symmetrical Li|0.5 m LiBF4 in [C3mpyr+][FSI–]|Li coin cells. Indeed it was found that introducing a rest period between cycling, and thereby allowing the chemical interaction between the Li electrode and electrolyte to take place, also impacted on the charging/discharging process. For all Li surface treatments the electrode resistance decreased after cycling and was due to significant structural rearrangement of the surface layer. These results suggest that careful electrode pretreatment in a real battery system will be required before operation.

Effect of Imidazolium-based Ionic Liquids on the nanoscale morphology of CuTCNQ (TCNQ= 7, 7, 8, 8-tetracyanoquinodimethane) metal-organic semiconductors

We demonstrate for the first time the ionic-liquid-mediated synthesis of nanostructured CuTCNQ by the simple immersion of copper in a solution of TCNQ where the viscosity of the medium significantly impacts the corrosion–crystallization process and the final morphology of the material.

Probing the effect of charge transfer enhancement in off resonance mode SERS via conjugation of the probe dye between silver nanoparticles and metal substrates

The charge transfer-mediated surface enhanced Raman scattering (SERS) of crystal violet (CV) molecules that were chemically conjugated between partially polarized silver nanoparticles and optically smooth gold and silver substrates has been studied under off-resonant conditions. Tyrosine molecules were used as a reducing agent to convert silver ions into silver nanoparticles where oxidised tyrosine caps the silver nanoparticle surface with its semiquinone group. This binding through the quinone group facilitates charge transfer and results in partially oxidised silver. This establishes a chemical link between the silver nanoparticles and the CV molecules, where the positively charged central carbon of CV molecules can bind to the terminal carboxylate anion of the oxidised tyrosine molecules. After drop casting Ag nanoparticles bound with CV molecules it was found that the free terminal amine groups tend to bind with the underlying substrates. Significantly, only those CV molecules that were chemically conjugated between the partially polarised silver nanoparticles and the underlying gold or silver substrates were found to show SERS under off-resonant conditions. The importance of partial charge transfer at the nanoparticle/capping agent interface and the resultant conjugation of CV molecules to off resonant SERS effects was confirmed by using gold nanoparticles prepared in a similar manner. In this case the capping agent binds to the nanoparticle through the amine group which does not facilitate charge transfer from the gold nanoparticle and under these conditions SERS enhancement in the sandwich configuration was not observed.

Effect of overload cycles on thin steel roof claddings during cyclonic winds

During an investigation on thin steel roof claddings under simulated cyclonic wind loading, it was found that trapezoidal roof claddings behaved quite differently to corrugated (arc and tangent type) roof claddings due to the presence of overload cycles. The overload cycles caused a reduction in fatigue life for corrugated roofing whereas the reverse occurred for trapezoidal roofing. This contrasting behavior of the two crest-fixed roof claddings was investigated using small scale roofing models instead of the commonly used large scale two-span roof claddings. It was found that overload cycles formed a weaker locally dimpled mechanism around the fastener holes of corrugated roofing and thus accelerated the fatigue-caused pull-through failure. In contrast, a stronger deformed shape was formed in trapezoidal roofing which delayed the pull-through failure. Both laboratory testing and finite element analysis of small scale models were used to study the contrasting behavior of roof claddings.

The legitimacy disconnect: Exploring the why and how of CSR communication

Whilst there is a growing body of research considering corporate social responsibility (CSR) communication, calls have been made to consider the ‘how’ of CSR communication (Maon, Lindgreen, & Swaen, 2010). The challenge with exploring this however, is that communication research has largely been criticised for failing to consider the macro-phenomena impacting communication (Jones, Watson, Gardner, & Gallois, 2004; Lammers & Barbour, 2006). As such, limited attention has been given to who organisations need to indicate their responsiveness to in relation to CSR, and in turn, why they communicate about certain activities in their CSR reports. Without exploring these ideas, and hence, gaining an understanding of the macro-phenomena impacting CSR communication, we limit our understanding of the ‘how’ of CSR communication. As such, this study sought to explore both the why of CSR communication, and in turn, the implications this may have for the how of CSR communication. To do this, this study drew on the notions of institutional theory, legitimacy, and rhetoric, and explored propositions drawn from these concepts to consider the why and how of CSR communication. Extended abstract attached

Effect of heat treatment and bend strain on the Jc of Ag-sheathed Bi-2212 tape

Bi-2212 tapes were fabricated using a powder-in-tube method and their superconducting properties were measured as a function of heat treatment. The tapes were heated to temperature, T1 (884-915 °C), and kept at that temperature for 20 min to induce partial (incongruent) melting. The samples were cooled to T2 with a ramp rate of 120 °C h-1 and then slowly cooled to T3 with a cooling rate, R2, and from T3 to T4 with a cooling rate, R3. The tapes were kept at the temperature T4 for P1 hours and then cooled to room temperature. Both R1 and R2 were chosen between 2 and 8 °C h-1. It was found that the structure and Jc of the tapes depend on the sintering conditions, i.e. T1-4, R1-3 and P1. The highest Jc of 5800 Å cm-2 was obtained at 77 K in a self-field with heat treatment where T1 = 894 and 899 °C, R1 = R2 = 5 °C h-1 and P1 = 6 h were employed. When 0.7% of bend strain, which is equivalent to a bend radius of 5 mm, was applied to the tape, 80% of the initial Jc was sustained.

The effect of organ motion of radiotherapy plans

Organ motion as a result of respiration is an important field of research for medical physics. Knowledge of magnitude and direction of this motion is necessary to allow for more accurate radiotherapy treatment planning. This will result in higher doses to the tumour whilst sparing healthy tissue. This project involved human trials, where the radiation therapy patient's kidneys were CT scanned under three different conditions; whilst free breathing (FB), breath-hold at normal tidal inspiration (BHIN), and breath-hold at normal tidal expiration (BHEX). The magnitude of motion was measured by recording the outline of the kidney from a Beam's Eye View (BEV). The centre of mass of this 2D shape was calculated for each set using "ImageJ" software and the magnitude of movement determined from the change in the centroid's coordinates between the BHIN and BHEX scans. The movement ranged from, for the left and right kidneys, 4-46mm and 2-44mm in the superior/inferior (axial) plane, 1-21mm and 2- 16mm in the anterior/posterior (coronal) plane, and 0-6mm and 0-8mm in the lateral/medial (sagittal) plane. From exhale to inhale, the kidneys tended to move inferiorly, anteriorly and laterally. A standard radiotherapy plan, designed to treat the para-aortics with opposed lateral fields was performed on the free breathing (planning) CT set. The field size and arrangement was set up using the same parameters for each subject. The prescription was to deliver 45 Gray in 25 fractions. This field arrangement and prescription was then copied over to the breath hold CT sets, and the dosimetric differences were compared using Dose Volume Histograms (DVH). The point of comparison for the three sets was recorded as the percentage volume of kidney receiving less than or equal to 10 Gray. The QUASAR respiratory motion phantom was used with the range of motion determined from the human study. The phantom was imaged, planned and treated with a linear accelerator with dose determined by film. The effect of the motion was measured by the change in the penumbra of the film and compared to the penumbra from the treatment planning system.