The influence of temperature and introduction point on the detection of Rhyzopertha dominica in stored grain

The presence of insect pests in grain storages throughout the supply chain is a significant problem for farmers, grain handlers, and distributors world-wide. Insect monitoring and sampling programmes are used in the stored grains industry for the detection and estimation of pest populations. At the low pest densities dictated by economic and commercial requirements, the accuracy of both detection and abundance estimates can be influenced by variations in the spatial structure of pest populations over short distances. Geostatistical analysis of Rhyzopertha dominica populations in 2 and 3 dimensions showed that insect numbers were positively correlated over short (0.5 cm) distances, and negatively correlated over longer (.10 cm) distances. At 35 C, insects were located significantly further from the grain surface than at 25 and 30 C. Dispersion metrics showed statistically significant aggregation in all cases. The observed heterogeneous spatial distribution of R. dominica may also be influenced by factors such as the site of initial infestation and disturbance during handling. To account for these additional factors, I significantly extended a simulation model that incorporates both pest growth and movement through a typical stored-grain supply chain. By incorporating the effects of abundance, initial infestation site, grain handling, and treatment on pest spatial distribution, I developed a supply chain model incorporating estimates of pest spatial distribution. This was used to examine several scenarios representative of grain movement through a supply chain, and determine the influence of infestation location and grain disturbance on the sampling intensity required to detect pest infestations at various infestation rates. This study has investigated the effects of temperature, infestation point, and grain handling on the spatial distribution and detection of R. dominica. The proportion of grain infested was found to be dependent upon abundance, initial pest location, and grain handling. Simulation modelling indicated that accounting for these factors when developing sampling strategies for stored grain has the potential to significantly reduce sampling costs while simultaneously improving detection rate, resulting in reduced storage and pest management cost while improving grain quality.

Infrared and Raman spectroscopic characterization of the borate mineral colemanite – CaB3O4(OH)3·H2O – implications for the molecular structure

Colemanite CaB3O4(OH)3 H2O is a secondary borate mineral formed from borax and ulexite in evaporate deposits of alkaline lacustrine sediments. The basic structure of colemanite contains endless chains of interlocking BO2(OH) triangles and BO3(OH) tetrahedrons with the calcium, water and extra hydroxide units interspersed between these chains. The Raman spectra of colemanite is characterized by an intense band at 3605 cm-1 assigned to the stretching vibration of OH units and a series of bands at 3182, 3300, 3389 and 3534 cm-1 assigned to water stretching vibrations. Infrared bands are observed in similar positions. The BO stretching vibrations of the trigonal and tetrahedral boron are characterized by Raman bands at 876, 1065 and 1084 cm-1. The OBO bending mode is defined by the Raman band at 611 cm-1. It is important to characterize the very wide range of borate minerals including colemanite because of the very wide range of applications of boron containing minerals.

Investigation of ultra trace detection in functionalised-surface enhanced Raman spectroscopy (SERS)

We have developed an explanation for ultra trace detection found when using Au/Ag SERS nanoparticles linked to biochemical affinity tags, e.g. antibodies. The nanoparticle structure is not as usually assumed and the aggregated nanoparticles constitute hot spots that are indispensable for these very low levels of analyte detection, even more so when using a direct detection method.

Liveness detection based on 3D face shape analysis

In recent years face recognition systems have been applied in various useful applications, such as surveillance, access control, criminal investigations, law enforcement, and others. However face biometric systems can be highly vulnerable to spoofing attacks where an impostor tries to bypass the face recognition system using a photo or video sequence. In this paper a novel liveness detection method, based on the 3D structure of the face, is proposed. Processing the 3D curvature of the acquired data, the proposed approach allows a biometric system to distinguish a real face from a photo, increasing the overall performance of the system and reducing its vulnerability. In order to test the real capability of the methodology a 3D face database has been collected simulating spoofing attacks, therefore using photographs instead of real faces. The experimental results show the effectiveness of the proposed approach.

Vibrational spectroscopic characterization of the phosphate mineral barbosalite Fe2+Fe3+2(PO4)2(OH)2 : implications for the molecular structure

Natural single-crystal specimens of barbosalite from Brazil, with general formula Fe2+Fe3+ 2 (PO4)2(OH)2 were investigated by Raman and infrared spectroscopy. The mineral occurs as secondary products in granitic pegmatites. The Raman spectrum of barbosalite is characterized by bands at 1020, 1033 and 1044 cm−1 cm−1, assigned to ν1 symmetric stretching mode of the HOPO3- 3 and PO3- 4 units. Raman bands at around 1067, 1083 and 1138 cm−1 are attributed to both the HOP and PO antisymmetric stretching vibrations. The set of Raman bands observed at 575, 589 and 606 cm−1 are assigned to the ν4 out of plane bending modes of the PO4 and H2PO4 units. Raman bands at 439, 461, 475 and 503 cm−1 are attributed to the ν2 PO4 and H2PO4 bending modes. Strong Raman bands observed at 312, 346 cm−1 with shoulder bands at 361, 381 and 398 cm−1 are assigned to FeO stretching vibrations. No bands which are attributable to water vibrations were found. Vibrational spectroscopy enables aspects of the molecular structure of barbosalite to be assessed.

Factors influencing the impact of primary and secondary prevention strategies for cervical cancer among Queensland women

Since the introduction of the National Human Papillomavirus Vaccine Program (NHPVP) in 2007, few studies have assessed women's knowledge, beliefs and attitudes towards cervical screening and human papillomavirus (HPV) vaccination in Australia. It is imperative to ascertain this, as substantial changes are anticipated to the National Cervical Screening Program (NCSP) through a process called 'the Renewal', to ensure any changes that are introduced will be acceptable and well understood by women. The objectives of this study were to describe Queensland women's current knowledge of cervical cancer/screening and HPV, their beliefs and attitudes towards Pap smears and the HPV vaccine and seek their advice on effective methods for communicating changes to the NCSP in their communities. This research was a descriptive-exploratory study that incorporated a combination of qualitative and quantitative methods within the context of the Health Belief Model (HBM). A computer-assisted telephone interview (CATI) survey of 1002 Queensland women was conducted in Phase 1 of the study. During Phase 2 of the study, 23 focus groups were conducted throughout Queensland to gather in-depth information about women's knowledge, awareness and acceptance about cervical cancer prevention strategies. This study found high levels of awareness of HPV (over 60%) and the HPV vaccine (over 86%) amongst Queensland women. However, it also identified considerable uncertainty amongst participants about perceived susceptibility to cervical cancer, especially, the link between cervical cancer, HPV and sexual activity. Women also had limited understanding of the benefit of the Pap smear as a preventative strategy, with many women thinking the main purpose of the Pap smear was for the early detection of cancer. Despite high awareness of HPV, women participating in this study also had significant knowledge deficits about their susceptibility to HPV and the severity of HPV infection. Queensland women had high levels of awareness of the HPV vaccine, which was most commonly via the media. High acceptance of the HPV vaccine was found amongst participants although awareness of the full benefits of vaccination was not evident with little acknowledgement that the quadrivalent vaccine used in the NHPVP would also prevent genital warts. Extensive barriers to having Pap smears, including physical and psychological discomfort, were identified and the most common barriers to vaccination were concerns about side effects and a lack of information upon which to make a decision about consent. Women described enablers for screening participation, such as reminder systems and practitioner characteristics, and expressed positive views towards self collected testing as an enabler, particularly for women who did not attend screening. As this study was conducted with Queensland women it may therefore not be representative of women from other parts of Australia and as participants were more likely to report they were regular screeners than Queensland women overall, these results may not be representative of women least likely to participate in cervical screening. The use of self-reported cervical screening history may also have led to over-reporting of screening status and previous abnormalities by participants. This study reveals significant gaps in Queensland women's knowledge that require effective communication strategies to address. Recommendations from this study highlight the need for increased community education to raise awareness about primary and secondary cervical cancer prevention strategies, training of cervical screening providers in sensitive examination techniques, a reduction in costs associated with screening, the exploration of alternative service models and communication plans that incorporate methods women trust and recommend for disseminating information about changes to the NCSP. This study is the first large study to explore women's perceptions of the Pap smear and barriers to screening, their knowledge about HPV and their attitudes towards the HPV vaccine in Queensland, since the introduction of the NHPVP. It highlights considerable uncertainty about many aspects of cervical cancer and primary and secondary prevention strategies available in Australia and identified many barriers to cervical screening and concerns about HPV vaccination. These knowledge gaps and barriers need to be taken into account and addressed within the context of anticipated changes to the NCSP to ensure benefits are maximised for women in future primary and secondary cervical cancer prevention strategies in the Australian context.

Validation of a new tool to measure responsiveness and structure in the feeding context : the Authoritative Feeding Practices Questionnaire

How mothers interact with their toddlers around food lays the foundations for healthy eating and healthy weight gain in later life. This research involving 467 Australian first-time mothers of 2-year-old children resulted in the development of a new self-report tool, the Authoritative Feeding Practices Questionnaire, assessing maternal responsive feeding and mealtime structure. Secondary analysis of the NOURISH randomised controlled trial included theory-driven item selection, confirmatory factor analysis, evaluation of psychometric properties and construct validation. The result is a brief, reliable and valid new tool for evaluating the maternal feeding practices that support children to become healthy, independent eaters.

Vibrational spectroscopic characterization of the phosphate mineral althausite Mg2(PO4)(OH,F,O) – implications for the molecular structure

Natural single-crystal specimens of althausite from Brazil, with general formula Mg2(PO4)(OH,F,O) were investigated by Raman and infrared spectroscopy. The mineral occurs as a secondary product in granitic pegmatites. The Raman spectrum of althausite is characterized by bands at 1020, 1033 and 1044 cm-1, assigned to ν1 symmetric stretching modes of the HOPO33- and PO43- units. Raman bands at around 1067, 1083 and 1138 cm-1 are attributed to both the HOP and PO antisymmetric stretching vibrations. The set of Raman bands observed at 575, 589 and 606 cm-1 are assigned to the ν4 out of plane bending modes of the PO4 and H2PO4 units. Raman bands at 439, 461, 475 and 503 cm-1 are attributed to the ν2 PO4 and H2PO4 bending modes. Strong Raman bands observed at 312, 346 cm-1 with shoulder bands at 361, 381 and 398 cm-1 are assigned to MgO stretching vibrations. No bands which are attributable to water were found. Vibrational spectroscopy enables aspects of the molecular structure of althausite to be assessed.

Enabling aircraft emergency landings using active visual site detection

The ability to automate forced landings in an emergency such as engine failure is an essential ability to improve the safety of Unmanned Aerial Vehicles operating in General Aviation airspace. By using active vision to detect safe landing zones below the aircraft, the reliability and safety of such systems is vastly improved by gathering up-to-the-minute information about the ground environment. This paper presents the Site Detection System, a methodology utilising a downward facing camera to analyse the ground environment in both 2D and 3D, detect safe landing sites and characterise them according to size, shape, slope and nearby obstacles. A methodology is presented showing the fusion of landing site detection from 2D imagery with a coarse Digital Elevation Map and dense 3D reconstructions using INS-aided Structure-from-Motion to improve accuracy. Results are presented from an experimental flight showing the precision/recall of landing sites in comparison to a hand-classified ground truth, and improved performance with the integration of 3D analysis from visual Structure-from-Motion.

Modal flexibility method for structural damage detection in suspension bridges

Suspension bridges meet the steadily growing demand for lighter and longer bridges in today’s infrastructure systems. These bridges are designed to have long life spans, but with age, their main cables and hangers could suffer from corrosion and fatigue. There is a need for a simple and reliable procedure to detect and locate such damage, so that appropriate retrofitting can be carried out to prevent bridge failure. Damage in a structure causes changes in its properties (mass, damping and stiffness) which in turn will cause changes in its vibration characteristics (natural frequencies, modal damping and mode shapes). Methods based on modal flexibility, which depends on both the natural frequencies and mode shapes, have the potential for damage detection. They have been applied successfully to beam and plate elements, trusses and simple structures in reinforced concrete and steel. However very limited applications for damage detection in suspension bridges have been identified to date. This paper examines the potential of modal flexibility methods for damage detection and localization of a suspension bridge under different damage scenarios in the main cables and hangers using numerical simulation techniques. Validated finite element model (FEM) of a suspension bridge is used to acquire mass normalized mode shape vectors and natural frequencies at intact and damaged states. Damage scenarios will be simulated in the validated FE models by varying stiffness of the damaged structural members. The capability of damage index based on modal flexibility to detect and locate damage is evaluated. Results confirm that modal flexibility based methods have the ability to successfully identify damage in suspension bridge main cables and hangers.

Damage detection in cable structures using vibration characteristics

Cable structures find many applications such as in power transmission, in anchors and especially in bridges. They serve as major load bearing elements in suspension bridges, which are capable of spanning long distances. All bridges, including suspension bridges, are designed to have long service lives. However, during this long life, they become vulnerable to damage due to changes in loadings, deterioration with age and random action such as impacts. The main cables are more vulnerable to corrosion and fatigue, compared to the other bridge components, and consequently reduces the serviceability and ultimate capacity of the bridge. Detecting and locating such damage at the earliest stage is challenging in the current structural health monitoring (SHM) systems of long span suspension bridges. Damage or deterioration of a structure alters its stiffness, mass and damping properties which in turn modify its vibration characteristics. This phenomenon can therefore be used to detect damage in a structure. The modal flexibility, which depends on the vibration characteristics of a structure, has been identified as a successful damage indicator in beam and plate elements, trusses and simple structures in reinforced concrete and steel. Successful application of the modal flexibility phenomenon to detect and locate the damage in suspension bridge main cables has received limited attention in recent research work. This paper, therefore examines the potential of the modal flexibility based Damage Index (DI) for detecting and locating damage in the main cable of a suspension bridge under four different damage scenarios. Towards this end, a numerical model of a suspension bridge cable was developed to extract the modal parameters at both damaged and undamaged states. Damage scenarios considered in this study with varied location and severity were simulated by changing stiffness at particular locations of the cable model. Results confirm that the DI has the potential to successfully detect and locate damage in suspension bridge main cables. This simple method can therefore enable bridge engineers and managers to detect and locate damage in suspension bridges at an early stage, minimize expensive retrofitting and prevent bridge collapse.

Collagen in the scarless fetal skin wound : detection with picrosirius-polarization

Our group has developed an ovine model of deep dermal, partial-thickness burn where the fetus heals scarlessly and the lamb heals with scar. The comparison of collagen structure between these two different mechanisms of healing may elucidate the process of scarless wound healing. Picrosirius staining followed by polarized light microscopy was used to visualize collagen fibers, with digital capture and analysis. Collagen deposition increased with fetal age and the fibers became thicker, changing from green (type III collagen) to yellow/red (type I collagen). The ratio of type III collagen to type I was high in the fetus (166), whereas the lamb had a much lower ratio (0.2). After burn, the ratios of type III to type I collagen did not differ from those in control skin for either fetus or lamb. The fetal tissue maintained normal tissue architecture after burn while the lamb tissue showed irregular collagen organization. In conclusion, the type or amount of collagen does not alter significantly after injury. Tissue architecture differed between fetal and lamb tissue, suggesting that scar development is related to collagen cross-linking or arrangement. This study indicates that healing in the scarless fetal wound is representative of the normal fetal growth pattern, rather than a "response" to burn injury.

Database relation watermarking resilient against secondary watermarking attacks

There has been tremendous interest in watermarking multimedia content during the past two decades, mainly for proving ownership and detecting tamper. Digital fingerprinting, that deals with identifying malicious user(s), has also received significant attention. While extensive work has been carried out in watermarking of images, other multimedia objects still have enormous research potential. Watermarking database relations is one of the several areas which demand research focus owing to the commercial implications of database theft. Recently, there has been little progress in database watermarking, with most of the watermarking schemes modeled after the irreversible database watermarking scheme proposed by Agrawal and Kiernan. Reversibility is the ability to re-generate the original (unmarked) relation from the watermarked relation using a secret key. As explained in our paper, reversible watermarking schemes provide greater security against secondary watermarking attacks, where an attacker watermarks an already marked relation in an attempt to erase the original watermark. This paper proposes an improvement over the reversible and blind watermarking scheme presented in [5], identifying and eliminating a critical problem with the previous model. Experiments showing that the average watermark detection rate is around 91% even with attacker distorting half of the attributes. The current scheme provides security against secondary watermarking attacks.

Quantitative stem-loop RT-PCR for detection of microRNAs

Plant microRNAs (miRNAs) are a class of endogenous small RNAs that are essential for plant development and survival. They arise from larger precursor RNAs with a characteristic hairpin structure and regulate gene activity by targeting mRNA transcripts for cleavage or translational repression. Efficient and reliable detection and quantification of miRNA expression has become an essential step in understanding their specific roles. The expression levels of miRNAs can vary dramatically between samples and they often escape detection by conventional technologies such as cloning, northern hybridization and microarray analysis. The stem-loop RT-PCR method described here is designed to detect and quantify mature miRNAs in a fast, specific, accurate and reliable manner. First, a miRNA-specific stem-loop RT primer is hybridized to the miRNA and then reverse transcribed. Next, the RT product is amplified and monitored in real time using a miRNA-specific forward primer and the universal reverse primer. This method enables miRNA expression profiling from as little as 10 pg of total RNA and is suitable for high-throughput miRNA expression analysis.

Telomerase activity : detection and clinical implications in human cancer

Telomerase is an extremely important enzyme required for the immortalisation of tumour cells. Because the gene is activated in the vast majority of tumour tissues and remains unused in most somatic cells, it represents a marker with huge diagnostic, prognostic and treatment implications in cancer. This article summarises the basic structure and functions of telomerase and considers its clinical implications in colorectal and other cancers.