Corporate-cooperative management of fisheries: A potential alternative governance structure for low value small fisheries?

While the economic and environmental benefits of fisheries management are well accepted, the costs of effective management in low value fisheries, including the research necessary to underpin such management, may be considerable relative to the total economic benefits they may generate. Co-management is often seen as a panacea in low value fisheries. Increasing fisher participation increases legitimacy of management decision in the absence of detailed scientific input. However, where only a small number of operators exist, the potential benefits of co-management are negated by the high transaction cost to the individual fishers engaging in the management process. From an economic perspective, sole ownership has been identified as the management structure which can best achieve biological and economic sustainability. Moving low value fisheries with a small number of participants to a corporate-cooperative management model may come close to achieving these sole ownership benefits, with lower transaction costs. In this paper we look at the applicability of different management models with industry involvement to low value fisheries with a small number of participants. We provide an illustration as to how a fishery could be transitioned to a corporate-cooperative management model that captures the key benefits of sole management at a low cost and is consistent with societal objectives.

Determining heavy vehicle suspension health from vibratory wheel loads

A low-cost test bed was made from a modified heavy vehicle (HV) brake tester. By rotating a test HV’s wheel on an eccentric roller, a known vibration was imparted to the wheel under test. A control case for dampers in good condition was compared with two test cases of ineffective shock absorbers. Measurement of the forces at the bearings of the roller provided an indication of the HV wheel-forces. Where the level of serviceability of the shock absorbers varied, differences in wheel load provided a quality indicator corresponding to a change of damper characteristic. Conclusions regarding the levels of damper maintenance beyond which HV suspensions cause road damage and dynamic wheel forces at the threshold of tyre wear at which HV shock absorbers are normally replaced are presented.

National consumer credit laws, financial exclusion and interest rate caps : The case for diversity within a centralised framework

Australia is going through a major reform of consumer credit regulation, with the implementation of a proposal to transfer regulatory responsibility from the State and Territory Governments to the Commonwealth Government. While the broad policy approach is supported, the reform process has missed a significant opportunity to engage directly with issues of financial exclusion and with the potential role of regulation to reduce financial exclusion. The imposition of an interest rate cap can limit the impact of financial exclusion. However, the future of the existing interest rate caps is uncertain, given the diversity of approaches, and the heated debate that surrounds this issue. In the absence of support for regulatory initiatives to increase the availability of low cost, small loans, permitting regulatory diversity on this issue of interest rate caps, within an otherwise centralised regulatory framework., can minimise the impact of financial exclusion on consumers.

The role of intermediaries in the implementation and development of asynchronous rural access

In Orissa state, India, the DakNet system supports asynchronous Internet communication between an urban hub and rural nodes. DakNet is noteworthy in many respects, not least in how the system leverages existing transport infrastructure. Wi-Fi transceivers mounted on local buses send and receive user data from roadside kiosks, for later transfer to/from the Internet via wireless protocols. This store-and-forward system allows DakNet to offer asynchronous communication capacity to rural users at low cost. The original ambition of the DakNet system was to provide email and SMS facilities to rural communities. Our 2008 study of the communicative ecology surrounding the DakNet system revealed that this ambition has now evolved – in response to market demand – to the extent that e-shopping (rather than email) has become the primary driver behind the DakNet offer.

'Try hard' : Attitudes to advertising in online social networks

Advertising has recently entered many new spaces it does not fully understand. The rules that apply in traditional media do not always translate in new media environments. However, their low cost of entry and the availability of hard-to-reach target markets, such as Generation Y, make environments such as online social networking sites attractive to marketers. This paper accumulates teenage perspectives from two qualitative studies to identify attitudes towards advertising in online social network sites and develop implications for marketers seeking to advertising on social network sites.

The Special Broadcasting Service after 30 years : public service media and new ways of thinking about media and citizenship

This article considers the distinctive ways in which the Special Broadcasting Service (SBS) has evolved over its history since 1980, and how it has managed competing claims to being a multicultural yet broad-appeal broadcaster, and a comprehensive yet low-cost media service. It draws attention to the challenges presented by a global rethinking of the nature of citizenship and its relationship to media, for which SBS is well placed as a leader, and the challenges of online media for traditional public service media models, where SBS has arguably been a laggard, particularly when compared with the Australian Broadcasting Corporation (ABC). It notes recent work that has been undertaken by the author with others into user-created content strategies at SBS and how its online news and current affairs services have been evolving in recent years.

Motivation and perception factors influence buying home behaviour in Dilly, East Timor

Demand of low cost housing increased from 1995 to 1997 which is shown by the number of housing loan approval. In order to develop the most suitable marketing plan, developer needs to know some factors which influenced to the decision making process of buying house. This research used a residential development in PT Delta Comoro Permai, Dilly as a case study. A survey to homeowners has been done to evaluate the motivation and perception factors in buying home behaviour. The survey has been done on the 3rd August to 29th August 1998. In this study, four main components have been examined. Physical and linkage are not as important as environment and utilities for the homebuyer. Moreover, the result is consistent with developer’s motto ‘clean, secure, aesthetic, healthy and prosperity’. This study provides further recommendation in the environment and utilities components for the new development in the future.

Community engagement for development and application of 3D visualisation models : a two edged

Background: SEQ Catchments Ltd and QUT are collaborating on groundwater investigations in the SE Qld region, which utilise community engagement and 3D Visualisation methodologies. The projects, which have been funded by the Australian Government’s NHT and Caring for our Country programmes, were initiated from local community concerns regarding groundwater sustainability and quality in areas where little was previously known. ----- Objectives: Engage local and regional stakeholders to tap all available sources of information;•Establish on-going (2 years +) community-based groundwater / surface water monitoring programmes;•Develop 3D Visualisation from all available data; and•Involve, train and inform the local community for improved on-ground land and water use management. ----- Results and findings: Respectful community engagement yielded information, access to numerous monitoring sites and education opportunities at low cost, which would otherwise be unavailable. A Framework for Community-Based Groundwater Monitoring has been documented (Todd, 2008).A 3D visualisation models have been developed for basaltic settings, which relate surface features familiar to the local community with the interpreted sub-surface hydrogeology. Groundwater surface movements have been animated and compared to local rainfall using the time-series monitoring data.An important 3D visualisation feature of particular interest to the community was the interaction between groundwater and surface water. This factor was crucial in raising awareness of potential impacts of land and water use on groundwater and surface water resources.

Website physical activity interventions : preferences of potential users

Information and communication technologies (particularly websites and e-mail) have the potential to deliver health behavior change programs to large numbers of adults at low cost. Controlled trials using these new media to promote physical activity have produced mixed results. User-centered development methods can assist in understanding the preferences of potential participants for website functions and content, and may lead to more effective programs. Eight focus group discussions were conducted with 40 adults after they had accessed a previously trialed physical activity website. The discussions were audio taped, transcribed and interpreted using a themed analysis method. Four key themes emerged: structure, interactivity, environmental context and content. Preferences were expressed for websites that include simple interactive features, together with information on local community activity opportunities. Particular suggestions included online community notice boards, personalized progress charts, e-mail access to expert advice and access to information on specific local physical activity facilities and services. Website physical activity interventions could usefully include personally relevant interactive and environmentally focused features and services identified through a user-centered development process.

Solar powered UAV for fire prevention and planning

This project aims to develop a methodology for designing and conducting a systems engineering analysis to build and fly continuously, day and night, propelled uniquely by solar energy for one week with a 0.25Kg payload consuming 0.5 watt without fuel or pollution. An airplane able to fly autonomously for many days could find many applications. Including coastal or border surveillance, atmospherical and weather research and prediction, environmental, forestry, agricultural, and oceanic monitoring, imaging for the media and real-estate industries, etc. Additional advantages of solar airplanes are their low cost and the simplicity with which they can be launched. For example, in the case of potential forest fire risks during a warm and dry period, swarms of solar airplanes, easily launched with the hand, could efficiently monitor a large surface, reporting rapidly any fire starts. This would allow a fast intervention and thus reduce the cost of such disaster, in terms of human and material losses. At higher dimension, solar HALE platforms are expected to play a major role as communication relays and could replace advantageously satellites in a near future.

Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Vision-based detection and tracking of aerial targets for UAV collision avoidance

Machine vision represents a particularly attractive solution for sensing and detecting potential collision-course targets due to the relatively low cost, size, weight, and power requirements of the sensors involved (as opposed to radar). This paper describes the development and evaluation of a vision-based collision detection algorithm suitable for fixed-wing aerial robotics. The system was evaluated using highly realistic vision data of the moments leading up to a collision. Based on the collected data, our detection approaches were able to detect targets at distances ranging from 400m to about 900m. These distances (with some assumptions about closing speeds and aircraft trajectories) translate to an advanced warning of between 8-10 seconds ahead of impact, which approaches the 12.5 second response time recommended for human pilots. We make use of the enormous potential of graphic processing units to achieve processing rates of 30Hz (for images of size 1024-by- 768). Currently, integration in the final platform is under way.

Airborne vision-based collision-detection system

Machine vision represents a particularly attractive solution for sensing and detecting potential collision-course targets due to the relatively low cost, size, weight, and power requirements of vision sensors (as opposed to radar and TCAS). This paper describes the development and evaluation of a real-time vision-based collision detection system suitable for fixed-wing aerial robotics. Using two fixed-wing UAVs to recreate various collision-course scenarios, we were able to capture highly realistic vision (from an onboard camera perspective) of the moments leading up to a collision. This type of image data is extremely scarce and was invaluable in evaluating the detection performance of two candidate target detection approaches. Based on the collected data, our detection approaches were able to detect targets at distances ranging from 400m to about 900m. These distances (with some assumptions about closing speeds and aircraft trajectories) translate to an advanced warning of between 8-10 seconds ahead of impact, which approaches the 12.5 second response time recommended for human pilots. We overcame the challenge of achieving real-time computational speeds by exploiting the parallel processing architectures of graphics processing units found on commercially-off-the-shelf graphics devices. Our chosen GPU device suitable for integration onto UAV platforms can be expected to handle real-time processing of 1024 by 768 pixel image frames at a rate of approximately 30Hz. Flight trials using manned Cessna aircraft where all processing is performed onboard will be conducted in the near future, followed by further experiments with fully autonomous UAV platforms.

Development of a hemispherical compound Eye for egomotion estimation

Biological inspiration has produced some successful solutions for estimation of self motion from visual information. In this paper we present the construction of a unique new camera, inspired by the compound eye of insects. The hemispherical nature of the compound eye has some intrinsically valuable properties in producing optical flow fields that are suitable for egomotion estimation in six degrees of freedom. The camera that we present has the added advantage of being lightweight and low cost, making it suitable for a range of mobile robot applications. We present some initial results that show the effectiveness of our egomotion estimation algorithm and the image capture capability of the hemispherical camera.

Single camera vision-only SLAM on a suburban road network

Simultaneous Localization And Mapping (SLAM) is one of the major challenges in mobile robotics. Probabilistic techniques using high-end range finding devices are well established in the field, but recent work has investigated vision only approaches. This paper presents a method for generating approximate rotational and translation velocity information from a single vehicle-mounted consumer camera, without the computationally expensive process of tracking landmarks. The method is tested by employing it to provide the odometric and visual information for the RatSLAM system while mapping a complex suburban road network. RatSLAM generates a coherent map of the environment during an 18 km long trip through suburban traffic at speeds of up to 60 km/hr. This result demonstrates the potential of ground based vision-only SLAM using low cost sensing and computational hardware.