Solar evaporator-collectors : analyses and applications

Taking into consideration of growing energy needs and concern for environmental degradation, clean and inexhaustible energy source, such as solar energy, is receiving greater attention for various applications. The use of solar energy system reduces pollution, waste and has little or no harmful effects on the environment. It is appreciated that this source of energy can be complementary rather than being competitive to conventional energy sources. In order to collect and harness energy from the sun, a solar collector is essential. A solar collector is basically a heat exchanger that transforms solar radiant energy into heat or thermal energy. Improvement of performance is essential for commercial acceptance of their use in such applications. Many studies have been undertaken on the enhancement of thermal performance of solar collectors, using diverse materials of various shapes, dimensions and layouts. In the literature, various collector designs have been proposed and tested with the objective of meeting these requirements [1-8]. Omer et al. [1] found the efficiency of a solar collector of about 70% in a solar assisted heat pump system. Traditional solar collectors are single phase collectors, in which the working fluid is either air or water. Different modifications are suggested and applied to improve the heat transfer between the absorber and working fluid in a collector. These modifications include the use of absorber with fins attached [2,3], corrugated absorber [4,5], matrix type absorber [6], V-groove solar air collector [7]. Karim et al. [8] approached a review of design and construction of three types (flat, vee-grooved, and finned) of air collectors. Two-phase collectors, on the other hand, have significant potential for continuous operation round the clock, when used in conjunction with a compressor, as found in a solar assisted heat-pump cycle.

Optimisation methods for coupled thermodynamic and 1D design of radial-inflow turbines

Optimisation is a fundamental step in the turbine design process, especially in the development of non-classical designs of radial-inflow turbines working with high-density fluids in low-temperature Organic Rankine Cycles (ORCs). The present work discusses the simultaneous optimisation of the thermodynamic cycle and the one-dimensional design of radial-inflow turbines. In particular, the work describes the integration between a 1D meanline preliminary design code adapted to real gases and the performance estimation approach for radial-inflow turbines in an established ORC cycle analysis procedure. The optimisation approach is split in two distinct loops; the inner operates on the 1D design based on the parameters received from the outer loop, which optimises the thermodynamic cycle. The method uses parameters including brine flow rate, temperature and working fluid, shifting assumptions such as head and flow coefficients into the optimisation routine. The discussed design and optimisation method is then validated against published benchmark cases. Finally, using the same conditions, the coupled optimisation procedure is extended to the preliminary design of a radial-inflow turbine with R143a as working fluid in realistic geothermal conditions and compared against results from commercially-available software RITAL from Concepts-NREC.

Regulating supply-chains to address the occupational health and safety problems associated with precarious employment: The case of home-based clothing workers in Australia

Over the past 20 years the labour market, workforce and work organisation of most if not all industrialised countries have been significantly refashioned by the increased use of more flexible work arrangements, variously labelled as precarious employment or contingent work. There is now a substantial and growing body of international evidence that many of these arrangements are associated with a significant deterioration in occupational health and safety (OHS), using a range of measures such as injury rates, disease, hazard exposures and work-related stress. Moreover, there is an emerging body of evidence that these arrangements pose particular problems for conventional regulatory regimes. Recognition of these problems has aroused the concern of policy makers - especially in Europe, North America and Australia - and a number of responses have been adopted in terms of modifying legislation, producing new guidance material and codes of practice and revised enforcement practices. This article describes one such in itiative in Australia with regard to home-based clothing workers. The regulatory strategy developed in one Australian jurisdiction (and now being ‘exported’ into others) seeks to counter this process via contractual tracking mechanisms to follow the work, tie in liability and shift overarching legal responsibility to the top of the supply chain. The process also entails the integration of minimum standards relating to wages, hours and working conditions; OHS and access to workers’ compensation. While home-based clothing manufacture represents a very old type of ‘flexible’ work arrangement, it is one that regulators have found especially difficult to address. Further, the elaborate multi-tiered subcont racting and diffuse work locations found in this industry are also characteristic of newer forms of contingent work in other industries (such as some telework) and the regulatory challenges they pose (such as the tendency of elaborate supply chains to attenuate and fracture statutory responsibilities, at least in terms of the attitudes and behaviour of those involved).

Fabrication of optochemical and electrochemical sensors using thin films of porphyrin and phthalocyanine derivatives

This paper describes the fabrication of thin films of porphyrin and metallophthalocyanine derivatives on different substrates for the optochemical detection of HCl gas and electrochemical determination of L-cysteine (CySH). Solid state gas sensor for HCl gas was fabricated by coating meso-substituted porphyrin derivatives on glass slide and examined optochemical sensing of HCl gas. The concentration of gaseous HCl was monitored from the changes in the absorbance of Soret band. Among the different porphyrin derivatives, meso- tetramesitylporphyrin (MTMP) coated film showed excellent sensitivity towards HCl and achieved a detection limit of 0.03ppm HCl. Further, we have studied the self-assembly of 1,8,15,22-tetraaminometallophthalocyanine (4α-MTAPc; M = Co and Ni) from DMF on GC electrode. The CVs for the self-assembled monolayers (SAMs) of 4α-CoIITAPc and 4α-NiIITAPc show two pairs of well-defined redox couple corresponding to metal and ring. Using the 4α-CoIITAPc SAM modified electrode, sensitive and selective detection of L-cysteine was demonstrated. Further, the SAM modified electrode also successfully separates the oxidation potentials of AA and CySH with a peak separation of 320mV.

The impact of neuropsychological functioning and coping style on perceived stress in individuals with first-episode psychosis and healthy controls

Stress is implicated in the development and course of psychotic illness, but the factors that influence stress levels are not well understood. The aim of this study was to examine the impact of neuropsychological functioning and coping styles on perceived stress in people with first-episode psychosis (FEP) and healthy controls (HC). Thirty-four minimally treated FEP patients from the Early Psychosis Prevention and Intervention Centre, Melbourne, Australia, and 26 HC participants from a similar demographic area participated in the study. Participants completed a comprehensive neuropsychological test battery as well as the Coping Inventory for Stressful Situations (task-, emotion- and avoidance-focussed coping styles) and Perceived Stress Scale (PSS). Linear regressions were used to determine the contribution of neuropsychological functioning and coping style to perceived stress in the two groups. In the FEP group, higher levels of emotion-focussed and lower levels of task-focussed coping were associated with elevated stress. Higher premorbid IQ and working memory were also associated with higher subjective stress. In the HC group, higher levels of emotion-focussed coping, and contrary to the FEP group, lower premorbid IQ, working memory and executive functioning, were associated with increased stress. Lower intellectual functioning may provide some protection against perceived stress in FEP.

Response of laminated glass panels to near field blast events

This thesis develops and applies an analytical method to treat the blast response of glass façades and studies the influence of controlling parameters such as all component materials and geometric properties, support conditions and energy absorption, and hence establishes a framework for their design for a credible blast event.

Early mathematical learning: Number processing skills and executive function at 5 and 8 years of age

This research investigated differences and associations in performance in number processing and executive function for children attending primary school in a large Australian metropolitan city. In a cross-sectional study, performance of 25 children in the first full-time year of school, (Prep; mean age = 5.5 years) and 21 children in Year 3 (mean age = 8.5 years) completed three number processing tasks and three executive function tasks. Year 3 children consistently outperformed the Prep year children on measures of accuracy and reaction time, on the tasks of number comparison, calculation, shifting, and inhibition but not on number line estimation. The components of executive function (shifting, inhibition, and working memory) showed different patterns of correlation to performance on number processing tasks across the early years of school. Findings could be used to enhance teachers’ understanding about the role of the cognitive processes employed by children in numeracy learning, and so inform teachers’ classroom practices.

Prevalence and risk factors for foot and ankle musculoskeletal disorders experienced by nurses

Background Nurses are at high risk of musculoskeletal disorders (MSDs). Although the prevalence of MSDs of the lower back, upper limbs, neck and shoulders have been reported previously in nursing, few studies have evaluated MSDs of the foot and ankle. This study evaluated the prevalence of foot and ankle MSDs in nurses and their relation to individual and workplace risk factors. Methods A self-administered survey incorporating the Nordic Musculoskeletal Questionnaire (NMQ) was distributed, over a nine-week period, to all eligible nurses (n = 416) working in a paediatric hospital in Brisbane, Australia. The prevalence of MSDs for each of the NMQ body regions was determined. Bivariate and multivariable logistic regression analyses were conducted to examine the relationships between activity-limiting foot/ankle MSDs and risk factors related to the individual (age, body mass index, number of existing foot conditions, smoking history, general physical health [SF36 Physical Component Scale], footwear features) or the workplace (level of nursing position, work location, average hours worked, hours worked in previous week, time since last break from work). Results A 73% response rate was achieved with 304 nurses completing surveys, of whom 276 were females (91%). Mean age of the nurses was 37 years (±10), younger than the state average of 43 years. Foot/ankle MSDs were the most prevalent conditions experienced by nurses during the preceding seven days (43.8%, 95% CI 38.2-49.4%), the second most prevalent MSDs to impair physical activity (16.7%, 95% CI 13.0-21.3%), and the third most prevalent MSD, after lower-back and neck problems, during the preceding 12 months (55.3%, 95% CI 49.6-60.7%). Of the nurse and work characteristics investigated, obesity, poor general physical health, existing foot conditions and working in the intensive care unit emerged as statistically significant (p < 0.05) independent risk factors for activity-limiting foot/ankle MSDs. Conclusions Foot/ankle MSDs are common in paediatric hospital nurses and resulted in physical activity limitations in one out of every six nurses. We recommend targeted education programs regarding the prevention, self-management and treatment strategies for foot/ankle MSDs. Further research is needed into the impact of work location and extended shift durations on foot/ankle MSDs.

Modeling strategies in longitudinal data analysis: Covariate, variance function and correlation structure selection

A modeling paradigm is proposed for covariate, variance and working correlation structure selection for longitudinal data analysis. Appropriate selection of covariates is pertinent to correct variance modeling and selecting the appropriate covariates and variance function is vital to correlation structure selection. This leads to a stepwise model selection procedure that deploys a combination of different model selection criteria. Although these criteria find a common theoretical root based on approximating the Kullback-Leibler distance, they are designed to address different aspects of model selection and have different merits and limitations. For example, the extended quasi-likelihood information criterion (EQIC) with a covariance penalty performs well for covariate selection even when the working variance function is misspecified, but EQIC contains little information on correlation structures. The proposed model selection strategies are outlined and a Monte Carlo assessment of their finite sample properties is reported. Two longitudinal studies are used for illustration.

Social work and complex care systems: The case of people hospitalised with a disability

Health and hospital system reforms prioritise efficiency. However, initiatives can impact on people with new or existing disabilities who require time to maximise functional independence. With greater demands for shorter hospital stays social workers face increasing pressure to facilitate discharge. This paper reports findings from research identifying factors contributing to extended stays for adults with disabilities. We sought to better understand patient characteristics and discharge planning challenges by analysing a clinical data set of 80 patients and qualitative interviews with five experienced hospital social workers. Three key factors are identified: issues around rehabilitation services; assessment and planning for community care; and availability of and access to discharge options. Strategies to reduce length of stay are reported. We argue that building collaborative partnerships and working across multiple, complex systems and disciplines are vital to ensure these patients access appropriate community-based resources within the current health reform environment.

A f/oxymoron? : Women, creativity and the suburbs

Donald Horne famously wrote, ‘Australia was born urban and quickly grew suburban’ (1964), an observation that carries a weight of assumptions about suburban living. Historically, the Australian suburbs have been regarded as places of retreat, family life and female activity, and subsequently as a place where not much of interest happens. By contrast, a city's central areas are seen as more dynamic spaces and, with recent creative city thinking and planning, as potential powerhouses of innovation and creativity. This article challenges assumptions about suburban living as passive places of retreat through an examination of women in the creative workforce who are living and working in the suburbs. It draws on historical accounts of creative suburban activity and a research project that mapped and investigated the experience of creative workers in the outer suburbs of Brisbane and Melbourne. The study finds that there is much creative work occurring in suburban localities, but this is not as unusual as might be expected.

Illuminating the glass box: The lighting designs of Richard Kelly

A promotional brochure celebrating the completion of the Seagram Building in spring 1957 features on its cover intense portraits of seven men bisected by a single line of bold text that asks, “Who are these Men?” The answer appears on the next page: “They Dreamed of a Tower of Light” (Figures 1, 2). Each photograph is reproduced with the respective man’s name and project credit: architects, Mies van der Rohe and Philip Johnson; associate architect, Eli Jacques Kahn; electrical contractor, Harry F. Fischbach; lighting consultant, Richard Kelly; and electrical engineer, Clifton E. Smith. To the right, a rendering of the new Seagram Tower anchors the composition, standing luminous against a star-speckled night sky; its glass walls and bronze mullions are transformed into a gossamer skin that reveals the tower’s structural skeleton. Lightolier, the contract lighting manufacturer, produced the brochure to promote its role in the lighting of the Seagram Building, but Lightolier’s promotional copy was not far from the truth.

Role of libraries in building research endeavours

The research landscape is changing rapidly, and as a consequence the roles of libraries and librarians in supporting and working with researchers is also changing. Some of the drivers behind the changes in research practices and culture include: new technologies, government funding and measurement of research impact, and the importance of open access to data. In Australia, librarians work with researchers to help them identify high quality resources, increase their publication rate and manage and promote access to their research. QUT Library has established a number of initiatives to support researchers, including: establishment of the QUT digital repository ‘ePrints’; purchase of electronic books and electronic journals; programmes of workshops for researchers ; redesign of Library space and, and the creation of new staffing positions. The creation of the QUT ePrints repository was a major new initiative for the QUT Library. ePrints is a web-accessible repository of research outputs created for QUT staff and postgraduate students. The ePrints information is harvested by Google, and anyone searching for a QUT staff member on Google can find their publications listed in ePrints. This keynote address will discuss the context for the role of libraries in building research endeavours, highlight some examples of strategies and resources to supporting researchers. It will conclude with an outline of some key online resources for researchers in education. This presentation should be relevant for both individual researchers interested in conducting and promoting their own research, and for staff and organisations focused on building their support for research.

Primary students' group metacognitive processes in a computer supported collaborative learning environment

The current understanding of students’ group metacognition is limited. The research on metacognition has focused mainly on the individual student. The aim of this study was to address the void by developing a conceptual model to inform the use of scaffolds to facilitate group metacognition during mathematical problem solving in computer supported collaborative learning (CSCL) environments. An initial conceptual framework based on the literature from metacognition, cooperative learning, cooperative group metacognition, and computer supported collaborative learning was used to inform the study. In order to achieve the study aim, a design research methodology incorporating two cycles was used. The first cycle focused on the within-group metacognition for sixteen groups of primary school students working together around the computer; the second cycle included between-group metacognition for six groups of primary school students working together on the Knowledge Forum® CSCL environment. The study found that providing groups with group metacognitive scaffolds resulted in groups planning, monitoring, and evaluating the task and team aspects of their group work. The metacognitive scaffolds allowed students to focus on how their group was completing the problem-solving task and working together as a team. From these findings, a revised conceptual model to inform the use of scaffolds to facilitate group metacognition during mathematical problem solving in computer supported collaborative learning (CSCL) environments was generated.

Paving pathways : shaping the public health workforce through tertiary education

Public health educational pathways in Australia have traditionally been the province of Universities, with the Master of Public Health (MPH) recognised as the flagship professional entry program. Public health education also occurs within the fellowship training of the Faculty of Public Health Medicine, but within Australia this remains confined to medical graduates. In recent years, however, we have seen a proliferation of undergraduate degrees as well as an increasing public health presence in the Vocational Education and Training (VET) sector. ----- Following the 2007 Australian Federal election, the new Labour government brought with it a refreshing commitment to a more inclusive and strategic style of government. An important example of this was the 2020 visioning process that identified key issues of public health concern, including an acknowledgment that it was unacceptable to allocate less than 2% of the health budget towards disease prevention. This led to the recommendation for the establishment of a national preventive health agency (Australia: the healthiest country by 2020 National Preventative Health Strategy, Prepared by the Preventative Health Taskforce 2009). ----- The focus on disease prevention places a spotlight on the workforce that will be required to deliver the new investment in health prevention, and also on the role of public health education in developing and upskilling the workforce. It is therefore timely to reflect on trends, challenges and opportunities from a tertiary sector perspective. Is it more desirable to focus education efforts on selected lead issues such as the “obesity epidemic”, climate change, Indigenous health and so on, or on the underlying theory and skills that build a flexible workforce capable of responding to a range of health challenges? Or should we aspire to both? ----- This paper presents some of the key discussion points from 2008 – 2009 of the Public Health Educational Pathways workshops and working group of the Australian Network of Public Health Institutions. We highlight some of the competing tensions in public health tertiary education, their impact on public health training programs, and the educational pathways that are needed to grow, shape and prepare the public health workforce for future challenges.