Effect of reactive bed mineralogy on arsenic retention and permeability of synthetic arsenic-containing acid mine drainage

Successive alkalinity producing systems (SAPSs) are widely used for treating acid mine drainage (AMD) and alleviating clogging commonly occurring in limestone systems due to an amorphous ferric precipitate. In this study, iron dust, bone char, micrite and their admixtures were used to treat arseniccontaining AMD. A particular interest was devoted to arsenic removal performance, mineralogical constraints on arsenic retention ability and permeability variation during column experiment for 140 days. The results showed that the sequence of the arsenic removal capacity was as follows: bone char > micrite > iron dust. The combination of 20% v/v iron dust and 80% v/v bone char/micrite columns can achieve better hydraulic conductivity and phosphorus-retention capacity than single micrite and bone char columns. The addition of iron dust created reductive environment and resulted in the transformation of coating material from colloidal phase to secondary mineral phase, such as green rust and phosphoerrite, which obviously ameliorates hydraulic conductivity of systems. The sequential extraction experiments indicated that the stable fractions of arsenic in columns were enhanced with help of iron dust compared to single bone char and micrite columns. A combination of iron dust and micrite/bone char represented a potential SAPS for treating As-containing AMD.

Mid- and near-infrared spectroscopic investigation of homogeneous cation distribution in MgxZnyAl(x+y)/2-layered double hydroxide (LDH)

In this report, a detailed FTIR fitting analysis was used to recognize Mg, Zn and Al homogeneous distribution in MgxZnyAl(x+y)/2-Layered double hydroxide (LDH) hydroxyl layer. In detail, OH-Mg2Al:OH-Mg3 ratios decreased from 95.2:4.8 (MIR) and 94.2:5.8 (NIR) to 58.9:41.1 (MIR) and 61.8:38.2 (NIR), when Mg:Al increased from 2.2:1.0 to 4.1:1.0 in MgAl-LDHs. These fitting results were similar with theoretical calculations of 94.3:5.7 and 59.0:41.0. In a further analysis of MgxZnyAl(x+y)/2-LDHs, OH bonded Zn2Mg, Zn2Al, MgZnAl, Mg2Al and Mg2Zn peaks were identified at 3420, 3430, 3445–3450, 3454 and 3545 cm-1, respectively. With the decrease of Mg:Zn from 3:1 to 1:3, metal-hydroxyl bands changed from OH-Mg2Al and MgZnAl (with a ratio of 49.4:50.6) to OH-MgZnAl and Zn2Al (with a ratio of 55.0:45.0). They were also similar with theoretical calculations of 47.6:52.4 and 54.6:45.4. As a result, these results show that there is an ordered cation distribution in MgxZnyAl(x+y)/2-LDH, and FTIR is feasible in recognizing this structure.

Nondiscretionary residential water use : the impact of habits and water-efficient technologies

Several studies published in the last few decades have demonstrated a low price-elasticity for residential water use. In particular, it has been shown that there is a quantity of water demanded that remains constant regardless of prices and other economic factors. In this research, we characterise residential water demand based on a Stone-Geary utility function. This specification is not only theory-compatible but can also explicitly model a minimum level of consumption not dependent on prices or income. This is described as minimum threshold or nondiscretionary water use. Additionally, the Stone-Geary framework is used to model the subsistence level of water consumption that is dependent on the temporal evolution of consumer habits and stock of physical capital. The main aim of this study is to analyse the impact of water-saving habits and water-efficient technologies on residential water demand, while additionally focusing attention on nondiscretionary uses. This is informed by an empirical application using data from a survey conducted among residents of Brisbane City Council, Australia. The results will be especially useful in the design of water tariffs and other water-saving policies.

The impact of mining and smelting activities on property values : a study of Mount Isa city, Queensland, Australia

Much publicity has been given to the problem of high levels of environmental contaminants, most notably high blood lead concentration levels among children in the city of Mount Isa because of mining and smelting activities. The health impacts from mining-related pollutants are now well documented. This includes published research being discussed in an editorial of the Medical Journal of Australia (see Munksgaard et al. 2010). On the other hand, negative impacts on property prices, although mentioned, have not been examined to date. This study rectifies this research gap. This study uses a hedonic property price approach to examine the impact of mining- and smelting-related pollution on nearby property prices. The hypothesis is that those properties closer to the lead and copper smelters have lower property (house) prices than those farther away. The results of the study show that the marginal willingness to pay to be farther from the pollution source is AUS $13 947 per kilometre within the 4 km radius selected. The study has several policy implications, which are discussed briefly. We used ordinary least squares, geographically weighted regression, spatial error and spatial autoregressive or spatial lag models for this analysis.

Social and cultural borders in Rio de Janeiro : the everyday life of community and mainstream photojournalists

This paper takes a multimethod approach which combines ethnographic techniques and discourse studies to investigate two contrasting professional groups: community photographers, who are favela dwellers who have developed photographic projects in Brazil‘s favelas, and photojournalists of the mainstream media. Its purpose is to determine how a cultural and social divide in the city of Rio de Janeiro shapes both community photographers and mainstream photojournalists’ practices, discourses, and identities. While community photographers strive to establish a humane and positive view about favelas and their residents by shifting the focus from poverty, shortages, violence, and criminality to images of the ordinary life, mainstream photojournalists express the view that their role is of primary importance for the defence of human rights in the favelas by helping to prevent, for instance, police abuses and violations. As the data analysis indicated the existence of socio-spatial borders all over Rio de Janeiro, this study adopted the idea of a divided city without denying interconnections between favelas and the city’s political life. Through the analysis of categories which emerged from the data, the complex world of documenting favela life is explored. The major themes touched upon are: the breakdown between the mainstream media and the favela communities; the different kinds of relationships which arise in Rio’s low income suburbs; and the gradual return of mainstream news workers to favelas.

The politics of open-access publishing : M/C Journal, Public Intellectualism, and Academic Discourses of Legitimacy

This article investigates the discourses of academic legitimacy that surround the production, consumption, and accreditation of online scholarship. Using the web-based media and cultural studies journal (http://journal.media-culture.org.au) as a case study, it examines how online scholarly journals often position themselves as occupying a space between the academic and the popular and as having a functional advantage over print-based media in promoting a spirit of public intellectualism. The current research agenda of both government and academe prioritises academic research that is efficient, self-promoting, and relevant to the public. Yet, although the cost-effectiveness and public-intellectual focus of online scholarship speak to these research priorities, online journals such as M/C Journal have occupied, and continue to occupy, an unstable position in relation to the perceived academic legitimacy of their content. Although some online scholarly journals have achieved a limited form of recognition within a system of accreditation that still privileges print-based scholarship, I argue that this, nevertheless, points to the fact that traditional textual notions of legitimate academic work continue to pervade the research agenda of an academe that increasingly promotes flexible delivery of teaching and online research initiatives.

Security analysis of Australian and E.U. e-passport implementation

This paper makes a formal security analysis of the current Australian e-passport implementation using model checking tools CASPER/CSP/FDR. We highlight security issues in the current implementation and identify new threats when an e-passport system is integrated with an automated processing system like SmartGate. The paper also provides a security analysis of the European Union (EU) proposal for Extended Access Control (EAC) that is intended to provide improved security in protecting biometric information of the e-passport bearer. The current e-passport specification fails to provide a list of adequate security goals that could be used for security evaluation. We fill this gap; we present a collection of security goals for evaluation of e-passport protocols. Our analysis confirms existing security weaknesses that were previously identified and shows that both the Australian e-passport implementation and the EU proposal fail to address many security and privacy aspects that are paramount in implementing a secure border control mechanism. ACM Classification C.2.2 (Communication/Networking and Information Technology – Network Protocols – Model Checking), D.2.4 (Software Engineering – Software/Program Verification – Formal Methods), D.4.6 (Operating Systems – Security and Privacy Protection – Authentication)

Effect of strong acids on red mud structural and fluoride adsorption properties

The removal of fluoride using red mud has been improved by acidifying red mud with hydrochloric, nitric and sulphuric acid. This investigation shows that the removal of fluoride using red mud is significantly improved if red mud is initially acidified. The acidification of red mud causes sodalite and cancrinite phases to dissociate, confirmed by the release of sodium and aluminium into solution as well as the disappearance of sodalite bands and peaks in infrared and X-ray diffraction data. The dissolution of these mineral phases increases the amount of available iron and aluminium oxide/hydroxide sites that are accessible for the adsorption of fluoride. The removal of fluoride is dependent on the charge of iron and aluminium oxide/hydroxides on the surface of red mud. Acidifying red mud with hydrochloric, nitric and sulphuric acid resulted in surface sites of the form ≡ SOH2+ and ≡ SOH. Optimum removal is obtained when the majority of surface sites are in the form ≡ SOH2+ as the substitution of a fluoride ion doesn’t cause a significant increase in pH. This investigation shows the importance of having a low and consistent pH for the removal of fluoride from aqueous solutions using red mud.

Insight into morphology and structure of different particle sized kaolinites with same origin

The particle size, morphology, crystallinity order and structural defects of four kaolinite samples are characterized by the techniques including particle size analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and magic angle spinning nuclear magnetic resonance spectroscopy (MAS NMR). The particle size of four kaolinite samples gradually increases. Four samples all belong to the ordered kaolinite and show a decrease in structural order with the increase of kaolinite particle size. The changes of structural defect are proved by the increase of the band splitting in Raman spectroscopy, the decrease of the intensity of absorption bands in infrared spectroscopy, and the decrease of equivalent silicon atom and the increase of nonequivalent aluminum atom in MAS NMR spectroscopy. The differences in morphology and structural defect are attributed to the broken bonds of Al–O–Si, Al–O–Al and Si–O–Si and the Al substitution for Si in tetrahedral sheets.

Intercalation of dodecylamine into kaolinite and its layering structure investigated by molecular dynamics simulation

Dodecylamine was successfully intercalated into the layer space of kaolinite by utilizing the methanol treated kaolinite–dimethyl sulfoxide (DMSO) intercalation complex as an intermediate. The basal spacing of kaolinite, measured by X-ray diffraction (XRD), increased from 0.72 nm to 4.29 nm after the intercalation of dodecylamine. Also, the significant variation observed in the Fourier Transform Infrared Spectroscopy (FTIR) spectra of kaolinite when intercalated with dodecylamine verified the feasibility of intercalation of dodecylamine into kaolinite. Isothermal-isobaric (NPT) molecular dynamics simulation with the use of Dreiding force field was performed to probe into the layering behavior and structure of nanoconfined dodecylamine in the kaolinite gallery. The concentration profiles of the nitrogen atom, methyl group and methylene group of intercalated dodecylamine molecules in the direction perpendicular to the kaolinite basal surface indicated that the alkyl chains within the interlayer space of kaolinite exhibited an obvious layering structure. However, the unified bilayer, pseudo-trilayer, or paraffin-type arrangements of alkyl chains deduced based on their chain length combined with the measured basal spacing of organoclays were not found in this study. The alkyl chains aggregated to a mixture of ordered paraffin-type-like structure and disordered gauche conformation in the middle interlayer space of kaolinite, and some alkyl chains arranged in two bilayer structures, in which one was close to the silica tetrahedron surface, and the other was close to the alumina octahedron surface with their alkyl chains parallel to the kaolinite basal surface.

Synthesis, characterization and activity of an immobilized photocatalyst : natural porous diatomite supported titania nanoparticles

Diatomite, a porous non-metal mineral, was used as support to prepare TiO2/diatomite composites by a modified sol–gel method. The as-prepared composites were calcined at temperatures ranging from 450 to 950 _C. The characterization tests included X-ray powder diffraction (XRD), scanning electron microscopy (SEM) with an energy-dispersive X-ray spectrometer (EDS), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption/desorption measurements. The XRD analysis indicated that the binary mixtures of anatase and rutile exist in the composites. The morphology analysis confirmed the TiO2 particles were uniformly immobilized on the surface of diatom with a strong interfacial anchoring strength, which leads to few drain of photocatalytic components during practical applications. In further XPS studies of hybrid catalyst, we found the evidence of the presence of Ti–O–Si bond and increased percentage of surface hydroxyl. In addition, the adsorption capacity and photocatalytic activity of synthesized TiO2/diatomite composites were evaluated by studying the degradation kinetics of aqueous Rhodamine B under UV-light irradiation. The photocatalytic degradation was found to follow pseudo-first order kinetics according to the Langmuir–Hinshelwood model. The preferable removal efficiency was observed in composites by 750 _C calcination, which is attributed to a relatively appropriate anatase/rutile mixing ratio of 90/10.

Mechanism of kaolinite sheets curling via the intercalation and delamination process

Kaolinite naturally occurs in the plate form for the interlayer hydrogen bond and the distortion and adaption of tetrahedron and octahedron. But kaolinite sheets can be exfoliated to nanoscrolls artificially in laboratory through multiple-step displacement intercalation. The driving force for kaolinite sheet to be curled nanoscroll originates from the size discrepancy of Si–O tetrahedron and Al–O octahedron. The displacement intercalation promoted the platy kaolinite sheets spontaneously to be scrolled by eliminating the interlayer hydrogen bond and atomic interaction. Kaolinite nanoscrolls are hollow tubes with outer face of tetrahedral sheet and inner face of octahedral sheet. Based on the theoretical calculation it is firstly reported that the minimum interior diameter for a single kaolinite sheet to be scrolled is about 9.08 nm, and the optimal 24.30 nm, the maximum 100 nm, which is verified by the observation of scanning electron microscope and transmission electron microscope. The different adaption types and discrepancy degree between tetrahedron and octahedron generate various curling forces in different directions. The nanoscroll axes prefer the directions as [100], [1 �10], [110], [3 �10], and the relative curling force are as follows, [3 �10] > [100] = [1�10] > [110].

Quality of life and caregiver outcomes following decompressive hemicraniectomy for severe stroke: A narrative literature review

AIMS The aim of this narrative review of the literature was to examine the current state of knowledge regarding the impact of aggressive surgical interventions for severe stroke on patient and caregiver quality of life and caregiver outcomes. BACKGROUND Decompressive hemicraniectomy (DHC) is a surgical therapeutic option for treatment of massive middle cerebral artery infarction (MCA), lobar intracerebral hemorrhage (ICH), and severe aneurysmal subarachnoid hemorrhage (aSAH). Decompressive hemicraniectomy has been shown to be effective in reducing mortality in these three life-threatening conditions. Significant functional impairment is an experience common to many severe stroke survivors worldwide and close relatives experience decision-making difficulty when confronted with making life or death choices related to surgical intervention for severe stroke. DATA SOURCES Academic Search Premier, Cumulative Index to Nursing and Allied Health Literature (CINAHL), Medline, and PsychInfo. REVIEW METHODS A narrative review methodology was utilized in this review of the literature related to long-term outcomes following decompressive hemicraniectomy for stroke. The key words decompressive hemicraniectomy, severe stroke, middle cerebral artery stroke, subarachnoid hemorrhage, lobar ICH, intracerebral hemorrhage, quality of life, and caregivers, literature review were combined to search the databases. RESULTS Good functional outcomes following DHC for life-threatening stroke have been shown to be associated with younger age and few co-morbid conditions. It was also apparent that quality of life was reduced for many stroke survivors, although not assessed routinely in studies. Caregiver burden has not been systematically studied in this population. CONCLUSION Most patients and caregivers in the studies reviewed agreed with the original decision to undergo DHC and would make the same decision again. However, little is known about quality of life for both patients and caregivers and caregiver burden over the long-term post-surgery. Further research is needed to generate information and interventions for the management of ongoing patient and carer recovery following DHC for severe stroke.