Electrochemical properties and intermediate-temperature fuel cell performance of dense yttrium-doped barium zirconate with calcium addition

Although BaZr 0.8Y 0.2O 3-δ(BZY) possesses large bulk proton conductivity and excellent chemical stability, its poor sinterability and grain boundaries block proton conduction. In this work, the effect of Ca as a co-dopant and as a sintering aid (as CaO), on the sinterability, proton conductivity, and fuel cell performance of BZY was investigated. The addition of 4 mol% CaO significantly improved the BZY sinterability: BZY pellets with densities of 92.7% and 97.5% with respect to the theoretical density were obtained after sintering at 1500°C and 1600°C, respectively. The improved BZY sinterability by CaO addition resulted also in a large proton conductivity; at 600°C, the total conductivity of BZY-CaO was 2.14 × 10 -3 S/cm, in wet Ar. Anode-supported fuel cells with 25 μm-thick BZY-CaO electrolyte membranes were fabricated by a dual-layer co-firing technique. The peak power density of the fuel cell with a BZY-Ni/BZY-4CaO/BZY-LSCF (La 0.6Sr 0.4Fe 0.8Co 0.2O 3-δ) configuration was 141 mW/cm 2 at 700°C, several times larger than the reported values of BZY electrolyte membrane fuel cells sintered with the addition of CuO or ZnO, demonstrating promising features for practical fuel cell applications.

Low-temperature synthesis and sintering of γ-Y2Si2O7

In this article, a novel pressureless solid-liquid reaction method is presented for preparation of yttrium disilicate (γ-Y2Si2O7). Single-phase γ-Y2Si2O7 powder was synthesized by calcination of SiO2 and Y2O3 powders with the addition of LiYO2 at 1400 °C for 4 h. The addition of LiYO2 significantly decreased the synthesis temperature, shortened the calcination time, and enhanced the stability of γ-Y2Si2O7. The sintering of these powders in air and O2 was studied by means of thermal mechanical analyzer. It is shown that the γ-Y2Si2O7 sintered in oxygen had a faster densification rate and a higher density than that sintered in air. Furthermore, single-phase γ-Y2Si2O7 with a density of 4.0 g/cm3 (99% of the theoretical density) was obtained by pressureless sintering at 1400 °C for 2 h in oxygen. Microstructures of the sintered samples are studied by scanning electron microscope.

The skin safety model: Reconceptualizing skin vulnerability in older patients

Purpose: To develop a unique skin safety model (SSM) that offers a new and unified perspective on the diverse yet interconnected antecedents that contribute to a spectrum of potential iatrogenic skin injuries in older hospitalized adults. Organizing Construct: Discussion paper. Methods: A literature search of electronic databases was conducted for published articles written in English addressing skin integrity and iatrogenic skin injury in elderly hospital patients between 1960 and 2014. Findings: There is a multiplicity of literature outlining the etiology, prevention, and management of specific iatrogenic skin injuries. Complex and interrelated factors contribute to iatrogenic skin injury in the older adult, including multiple comorbidities, factors influencing healthcare delivery, and acute situational stressors. A range of injuries can result when these factors are com- plicated by skin irritants, pressure, shear, or friction; however, despite skin injuries sharing multiple ntecedents, no unified overarching skin safety conceptual model has been published. Conclusions: The SSM presented in this article offers a new, unified framework that encompasses the spectrum of antecedents to skin vulnerability as well as the spectrum of iatrogenic skin injuries that may be sustained by older acute care patients. Current skin integrity frameworks address prevention and management of specific skin injuries. In contrast, the SSM recognizes the complex interplay of patient and system factors that may result in a range of iatrogenic skin injuries. Skin safety is reconceptualized into a single model that has the potential for application at the individual patient level, as well as health-care systems and governance levels. Clinical Relevance: Skin safety is concerned with keeping skin safe from any iatrogenic skin injury, and remains an ongoing challenge for healthcare providers. A conceptual framework that encompasses all of the factors that may contribute to a range of iatrogenic skin injuries is essential, and guides the clinician in maintaining skin integrity in the vulnerable older patient.

Fabrication of Fe-doped WO3 films for NO2 sensing at lower operating temperature

Fe-doped tungsten oxide thin films with different concentrations (0 to 2.6 at%) were synthesized on glass and alumina substrates at room temperature using DC reactive sputtering and subsequently annealed at 300oC for 1 hour in air. The alumina substrate has pre-printed interdigitated Pt-electrodes for gas sensing measurements. The effects of Fe-doping on the film structure and morphology, electronic and optical properties for gas sensing were investigated. The grain size of the different films on the alumina and Pt regions of the substrate vary only slightly between 43-57 nm with median size of about 50 nm. Raman spectra showed that the integrated intensity of W=O to O–W–O bands increases with increasing Fe concentrations and this indicated an increase in the number of defects. From XPS the different concentrations of the Fe-doped films were 0.03 at%, 1.33 at% and 2.6 at%. All the films deposited on glass substrate have shown similar visible transmittance (about 70%) but the optical band gap of the pure film decreased form 3.30 eV to 3.15 eV after doping with 2.6 at% Fe. The Fe-doped WO3 film with the highest Fe concentration (2.6 at% Fe) has shown an enhanced gas sensing properties to NO2 at relatively lower operating temperature (150oC) and this can be attributed to the decrease in the optical band gap and an increase in the number of defects compared to the pure WO3 film.

Prevalence, codetection and seasonal distribution of upper airway viruses and bacteria in children with acute respiratory illnesses with cough as a symptom

Most studies exploring the role of upper airway viruses and bacteria in paediatric acute respiratory infections (ARI) focus on specific clinicaldiagnoses and/or do not account for virus–bacteria interactions. We aimed to describe the frequency and predictors of virus and bacteria codetection in children with ARI and cough, irrespective of clinical diagnosis. Bilateral nasal swabs, demographic, clinical and risk factor data were collected at enrollment in children aged <15 years presenting to an emergency department with an ARI and where cough was a symptom. Swabs were tested by polymerase chain reaction for 17 respiratory viruses and seven respiratory bacteria. Logistic regression was used to investigate associations between child characteristics and codetection of the organisms of interest. Between December 2011 and August 2014, swabs were collected from 817 (93.3%) of 876 enrolled children, median age 27.7 months (interquartile range13.9–60.3 months). Overall, 740 (90.6%) of 817 specimens were positive for any organism. Both viruses and bacteria were detected in 423 specimens (51.8%). Factors associated with codetection were age (adjusted odds ratio (aOR) for age <12 months = 4.9, 95% confidence interval (CI) 3.0, 7.9; age 12 to <24 months = 6.0, 95% CI 3.7, 9.8; age 24 to <60 months = 2.4, 95% CI 1.5, 3.9), male gender (aOR 1.46; 95% CI 1.1, 2.0), child care attendance (aOR 2.0; 95% CI 1.4, 2.8) and winter enrollment (aOR 2.0; 95% CI 1.3, 3.0). Haemophilus influenzae dominated the virus–bacteria pairs. Virus–H. influenzae interactions in ARI should be investigated further, especially as the contribution of nontypeable H. influenzae to acute and chronic respiratory diseases is being increasingly recognized.

Reflections from East Asia's ageing population: An interaction designers' challenge

As Asia experiences the demographic imbalance between working and ageing populations, the need for attention in this area is highlighted. The shift of a country's age structure that results from people having small families and living long lives, where previously they had large families and lived short lives, results in more workers and fewer dependents creating economic growth, known as the demographic dividend. However for a generation after this bulge and dividend, a disproportionate number of older people must be supported by a smaller working population, a current concern in Asia with its rapidly growing number of older adults. This extended abstract draws practical and unique insights from three of the oldest and richest nations in Asia - Japan, South Korea and China, on the perspective of interactive technology design for older adults. ICT has powerful potential to ameliorate the imbalance in the population demographic through its potential to leverage various kinds of support. As HCI researchers, this is a challenge we embrace; a challenge for the ageing society of unique individuals to exploit the technologies that they have helped to create. The paper draws lessons from key sample studies, one from each country, which aimed to understand their ageing population. The insights for interaction designers are presented in the form of a practical set of reflections to guide the authors, who are in the early stages of research on technology design for older adults.