Steps towards the validation of the Trendelenburg test : The effect of experimentally reduced hip abductor muscle function on frontal plane mechanics

Introduction: The Trendelenburg Test (TT) is used to assess the functional strength of the hip abductor muscles (HABD), their ability to control frontal plane motion of the pelvis, and the ability of the lumbopelvic complex to transfer load into single leg stance. Rationale: Although a standard method to perform the test has been described for use within clinical populations, no study has directly investigated Trendelenburg’s hypotheses. Purpose: To investigate the validity of the TT using an ultrasound guided nerve block (UNB) of the superior gluteal nerve and determine whether the reduction in HABD strength would result in the theorized mechanical compensatory strategies measured during the TT. Methods: Quasi-experimental design using a convenience sample of nine healthy males. Only subjects with no current or previous injury to the lumbar spine, pelvis, or lower extremities, and no previous surgeries were included. Force dynamometry was used to evaluation HABD strength (%BW). 2D mechanics were used to evaluate contralateral pelvic drop (cMPD), change in contralateral pelvic drop (∆cMPD), ipsilateral hip adduction (iHADD) and ipsilateral trunk sway (TRUNK) measured in degrees (°). All measures were collected prior to and following a UNB on the superior gluteal nerve performed by an interventional radiologist. Results: Subjects’ age was median 31yrs (IQR:22-32yrs); and weight was median 73kg (IQR:67-81kg). An average 52% reduction of HABD strength (z=2.36,p=0.02) resulted following the UNB. No differences were found in cMPD or ∆cMPD (z=0.01,p= 0.99, z=-0.67,p=0.49). Individual changes in biomechanics show no consistency between subjects and non-systematic changes across the group. One subject demonstrated the mechanical compensations described by Trendelenburg. Discussion: The TT should not be used as screening measure for HABD strength in populations demonstrating strength greater than 30%BW but reserved for use with populations with marked HABD weakness. Importance: This study presents data regarding a critical level of HABD strength required to support the pelvis during the TT.

An accurate numerical scheme for the contraction of a bubble in a Hele-Shaw cell

We report on an accurate numerical scheme for the evolution of an inviscid bubble in radial Hele-Shaw flow, where the nonlinear boundary effects of surface tension and kinetic undercooling are included on the bubble-fluid interface. As well as demonstrating the onset of the Saffman-Taylor instability for growing bubbles, the numerical method is used to show the effect of the boundary conditions on the separation (pinch-off) of a contracting bubble into multiple bubbles, and the existence of multiple possible asymptotic bubble shapes in the extinction limit. The numerical scheme also allows for the accurate computation of bubbles which pinch off very close to the theoretical extinction time, raising the possibility of computing solutions for the evolution of bubbles with non-generic extinction behaviour.

A quasi-maximum likelihood method for estimating the parameters of multivariate diffusions

A quasi-maximum likelihood procedure for estimating the parameters of multi-dimensional diffusions is developed in which the transitional density is a multivariate Gaussian density with first and second moments approximating the true moments of the unknown density. For affine drift and diffusion functions, the moments are exactly those of the true transitional density and for nonlinear drift and diffusion functions the approximation is extremely good and is as effective as alternative methods based on likelihood approximations. The estimation procedure generalises to models with latent factors. A conditioning procedure is developed that allows parameter estimation in the absence of proxies.

Simplified method for including spatial correlations in mean-field approximations

Biological systems involving proliferation, migration and death are observed across all scales. For example, they govern cellular processes such as wound-healing, as well as the population dynamics of groups of organisms. In this paper, we provide a simplified method for correcting mean-field approximations of volume-excluding birth-death-movement processes on a regular lattice. An initially uniform distribution of agents on the lattice may give rise to spatial heterogeneity, depending on the relative rates of proliferation, migration and death. Many frameworks chosen to model these systems neglect spatial correlations, which can lead to inaccurate predictions of their behaviour. For example, the logistic model is frequently chosen, which is the mean-field approximation in this case. This mean-field description can be corrected by including a system of ordinary differential equations for pair-wise correlations between lattice site occupancies at various lattice distances. In this work we discuss difficulties with this method and provide a simplication, in the form of a partial differential equation description for the evolution of pair-wise spatial correlations over time. We test our simplified model against the more complex corrected mean-field model, finding excellent agreement. We show how our model successfully predicts system behaviour in regions where the mean-field approximation shows large discrepancies. Additionally, we investigate regions of parameter space where migration is reduced relative to proliferation, which has not been examined in detail before, and our method is successful at correcting the deviations observed in the mean-field model in these parameter regimes.

Development of a simplified design method to predict the fire rating of LSF walls

Recent fire research into the behaviour of light gauge steel frame (LSF) wall systems has devel-oped fire design rules based on Australian and European cold-formed steel design standards, AS/NZS 4600 and Eurocode 3 Part 1.3. However, these design rules are complex since the LSF wall studs are subjected to non-uniform elevated temperature distributions when the walls are exposed to fire from one side. Therefore this paper proposes an alternative design method for routine predictions of fire resistance rating of LSF walls. In this method, suitable equations are recommended first to predict the idealised stud time-temperature pro-files of eight different LSF wall configurations subject to standard fire conditions based on full scale fire test results. A new set of equations was then proposed to find the critical hot flange (failure) temperature for a giv-en load ratio for the same LSF wall configurations with varying steel grades and thickness. These equations were developed based on detailed finite element analyses that predicted the axial compression capacities and failure times of LSF wall studs subject to non-uniform temperature distributions with varying steel grades and thicknesses. This paper proposes a simple design method in which the two sets of equations developed for time-temperature profiles and critical hot flange temperatures are used to find the failure times of LSF walls. The proposed method was verified by comparing its predictions with the results from full scale fire tests and finite element analyses. This paper presents the details of this study including the finite element models of LSF wall studs, the results from relevant fire tests and finite element analyses, and the proposed equations.

Predicting fitness for chemotherapy in older cancer patients

Background: The Vulnerable Elders Survey-13 (VES-13) is increasingly used to screen for older patients who can proceed to intensive chemotherapy without further comprehensive assessment. This study compared the VES-13 determination of fitness for treatment with the oncologist's assessments of fitness. Method: Sample: Consecutive series of solid tumour patients ≥65 years (n=175; M=72; range=65-86) from an Australian cancer centre. Patients were screened with the VES-13 before proceeding to usual treatment. Blinded to screening, oncologists concurrently predicted patient fitness for chemotherapy. A sample of 175 can detect, with 90% power, kappa coefficients of agreement between VES-13 and oncologists’ assessments >0.90 ("almost perfect agreement"). Separate backward stepwise logistic regression analyses assessed potential predictors of VES-13 and oncologists’ ratings of fitness. Results: Kappa coefficient for agreement between VES-13 and oncologists’ ratings of fitness was 0.41 (p<0.001). VES-13 and oncologists’ assessments agreed in 71% of ratings. VES-13 sensitivity = 83.3%; specificity = 57%; positive predictive value = 69%; negative predictive value = 75%. Logistic regression modelling indicated that the odds of being vulnerable to chemotherapy (VES-13) increased with increasing depression (OR=1.42; 95% CI: 1.18, 1.71) and decreased with increased functional independence assessed on the Bartel Index (OR=0.82; CI: 0.74, 0.92) and Lawton instrumental activities of daily living (OR=0.44; CI: 0.30, 0.65); RSquare=.65. Similarly, the odds of a patient being vulnerable to chemotherapy, when assessed by physicians, increased with increasing age (OR=1.15; CI: 1.07, 1.23) and depression (OR=1.23; CI: 1.06, 1.43), and decreased with increasing functional independence (OR=0.91; CI: 0.85, 0.98); RSquare=.32. Conclusions: Our data indicate moderate agreement between VES-13 and clinician assessments of patients’ fitness for chemotherapy. Current ‘one-step’ screening processes to determine fitness have limits. Nonetheless, screening tools do have the potential for modification and enhanced predictive properties in cancer care by adding relevant items, thus enabling fit patients to be immediately referred for chemotherapy.

Ultra-trace detection of diagnostically important biomarkers using functionalised-Surface Enhanced Raman Spectroscopy (SERS)

Here we report an ultrasensitive method for detecting bio-active compounds in biological samples by means of functionalised nanoparticles interrogated by surface enhanced Raman spectroscopy (SERS). This method is applicable to the recovery and detection of many diagnostically important peptidyl analytes such as insulin, human growth hormone, growth factors (IGFs) and erythropoietin (EPO), as well as many small molecule analytes and metabolites. Our method, developed to detect EPO, demonstrates its utility in a complex yet well defined biological system. Recombinant human EPO (rhEPO) and EPO analogues have successfully been used to treat anaemia in end-stage renal failure, chronic disorders and infections, cancer and AIDS. Current methods for EPO testing are lengthy, laborious and relatively insensitive to low concentrations. In our rapid screening methodology, gold nanoparticles were functionalised with anti-EPO antibodies to provide very high selectivity towards the EPO protein in urine. These “smart sensor” nanoparticles interact with and trap EPO. Subsequent SERS screening allows for the detection and quantisation of ultra trace amounts (<<10-15 M) of EPO in urine samples with minimal sample preparation. We present data showing that the SERS spectrum differentiates between human endogenous EPO and rhEPO in unpurified urine, and potentially distinguishes between purified EPO isoforms. The elimination of sample preparation and direct screening in biological fluids significantly reduces the time required by current methods. Antibody recognition against a variety of biological targets and the availability of portable commercial SERS analysers for rapid onsite testing suggest broad diagnostic applicability in a flexible analytical platform.

Reconstructing 3D x-ray CT images of polymer gel dosimeters using the zero-scan method

In this study x-ray CT has been used to produce a 3D image of an irradiated PAGAT gel sample, with noise-reduction achieved using the ‘zero-scan’ method. The gel was repeatedly CT scanned and a linear fit to the varying Hounsfield unit of each pixel in the 3D volume was evaluated across the repeated scans, allowing a zero-scan extrapolation of the image to be obtained. To minimise heating of the CT scanner’s x-ray tube, this study used a large slice thickness (1 cm), to provide image slices across the irradiated region of the gel, and a relatively small number of CT scans (63), to extrapolate the zero-scan image. The resulting set of transverse images shows reduced noise compared to images from the initial CT scan of the gel, without being degraded by the additional radiation dose delivered to the gel during the repeated scanning. The full, 3D image of the gel has a low spatial resolution in the longitudinal direction, due to the selected scan parameters. Nonetheless, important features of the dose distribution are apparent in the 3D x-ray CT scan of the gel. The results of this study demonstrate that the zero-scan extrapolation method can be applied to the reconstruction of multiple x-ray CT slices, to provide useful 2D and 3D images of irradiated dosimetry gels.

Ab initio studies of hydrogen desorption from low index magnesium hydride surface

The low index Magnesium hydride surfaces, MgH2(0 0 1) and MgH2(1 1 0), have been studied by ab intio Density Functional Theory (DFT) calculations. It was found that the MgH2(1 1 0) surface is more stable than MgH2(0 0 1) surface, which is in good agreement with the experimental observation. The H2 desorption barriers vary depending on the crystalline surfaces that are exposed and also the specific H atom sites involved – they are found to be generally high, due to the thermodynamic stability of the MgH2 system, and are larger for the MgH2(0 0 1) surface. The pathway for recombinative desorption of one in-plane and one bridging H atom from the MgH2(1 1 0) surface was found to be the lowest energy barrier amongst those computed (172 KJ/mol) and is in good agreement with the experimental estimates.

Nonparametric semantic segmentation for 3D street scenes

In this paper we propose a method to generate a large scale and accurate dense 3D semantic map of street scenes. A dense 3D semantic model of the environment can significantly improve a number of robotic applications such as autonomous driving, navigation or localisation. Instead of using offline trained classifiers for semantic segmentation, our approach employs a data-driven, nonparametric method to parse scenes which easily scale to a large environment and generalise to different scenes. We use stereo image pairs collected from cameras mounted on a moving car to produce dense depth maps which are combined into a global 3D reconstruction using camera poses from stereo visual odometry. Simultaneously, 2D automatic semantic segmentation using a nonparametric scene parsing method is fused into the 3D model. Furthermore, the resultant 3D semantic model is improved with the consideration of moving objects in the scene. We demonstrate our method on the publicly available KITTI dataset and evaluate the performance against manually generated ground truth.

A discourse on the non-method

In spite of the activism of professional bodies and researchers, empirical evidence shows that project management still does not deliver the expected benefits and promises. Hence, many have questioned the validity of the hegemonic rationalist paradigm anchored in the Enlightenment and Natural Sciences tradition supporting project management research and practice for the last 60 years and the lack of relevance to practice of the current conceptual base of project management. In order to address these limitations many authors, taking a post-modernist stance in social sciences, build on ‘pre-modern’ philosophies such as the Aristotelian one, specially emphasizing the role of praxis (activity), and phronesis (practical wisdom, prudence). Indeed, ‘Praxis … is the central category of the philosophy which is not merely an interpretation of the world, but is also a guide to its transformation …’ (Vazquez, 1977:. 149). Therefore, praxis offers an important focus for practitioners and researchers in social sciences, one in which theory is integrated with practice at the point of intervention. Simply stated, praxis can serve as a common ground for those interested in basic and applied research by providing knowledge of the reality in which action, informed by theory, takes place. Consequently, I suggest a ‘praxeological’ style of reasoning (praxeology being defined as study or science of human actions and conduct, including praxis, practices and phronesis) and to go beyond the ‘Theory-Practice’ divide. Moreover, I argue that we need to move away from the current dichotomy between the two classes ‘scholars experts-researchers’ and ‘managers/workers-practitioners-participants’. Considering one single class of ‘PraXitioner’, becoming a phronimos, may contribute to create new perspectives and open up new ways of thinking and acting in project situations. Thus, I call for a Perestroika in researching and acting in project management situations. My intent is to suggest a balanced praxeological view of the apparent opposition between social and natural science approaches. I explore, in this chapter, three key questions, covering the ontological, epistemological and praxeological dimensions of project management in action. 1. Are the research approaches being currently used appropriate for generating contributions that matter to both theory and practice with regards to what a ‘project’ is or to what we do when we call a specific situation ‘a project’? 2. On the basis of which intellectual virtues is the knowledge generated and what is the impact for theory and practice? 3. Are the modes of action of the practitioners ‘prudent’ and are they differentiating or reconciling formal and abstract rationality from substantive rationality and situated reasoning with regards to the mode of action they adopt in particular project situations? The investigation of the above questions leads me to debate about ‘Project Management-as-Praxis’, and to suggest ‘A’ (not ‘THE’) ‘praxeological’ style of reasoning and mode of inquiry – acknowledging a non-paradigmatic, subjective and kaleidoscopic perspective – for ‘Knowing-as-Practicing’ in project management. In short, this is about making a ‘Projects Science’ that matters.

A method for predicting rain-induced instability of an individual slope

Awareness to avoid losses and casualties due to rain-induced landslide is increasing in regions that routinely experience heavy rainfall. Improvements in early warning systems against rain-induced landslide such as prediction modelling using rainfall records, is urgently needed in vulnerable regions. The existing warning systems have been applied using stability chart development and real-time displacement measurement on slope surfaces. However, there are still some drawbacks such as: ignorance of rain-induced instability mechanism, mislead prediction due to the probabilistic prediction and short time for evacuation. In this research, a real-time predictive method was proposed to alleviate the drawbacks mentioned above. A case-study soil slope in Indonesia that failed in 2010 during rainfall was used to verify the proposed predictive method. Using the results from the field and laboratory characterizations, numerical analyses can be applied to develop a model of unsaturated residual soils slope with deep cracks and subject to rainwater infiltration. Real-time rainfall measurement in the slope and the prediction of future rainfall are needed. By coupling transient seepage and stability analysis, the variation of safety factor of the slope with time were provided as a basis to develop method for the real-time prediction of the rain-induced instability of slopes. This study shows the proposed prediction method has the potential to be used in an early warning system against landslide hazard, since the FOS value and the timing of the end-result of the prediction can be provided before the actual failure of the case study slope.

Integration of Saudi Arabia’s conservative Islamic culture in sustainable housing design

The cities of Saudi Arabia have perhaps the largest growth rates of cities in the Middle East, such that it has become a cause in shortage of housing for mid and low-income families, as is the case in other developing countries. Even when housing is found, it is not sustainable nor is it providing the cultural needs of those families. The aim of this paper is to integrate the unique conservative Islamic Saudi culture into the design of sustainable housing. This paper is part of a preliminary study of an on-going PhD thesis, which utilises a semistructured interview of a panel of nine experts in collecting the data. The interviews consisted of ten questions ranging from general questions such as stating their expertise and work position to more specific question such as listing the critical success factors and/or barriers for applying sustainability to housing in Saudi Arabia. Since the participants were selected according to their experience, the answers to the interview questions were satisfactory where the generation of the survey questions for the second stage in the PhD thesis took place after analysing the participant’s answers to the interview questions. This paper recommends design requirements for accommodating the conservative Islamic Saudi Culture in low cost sustainable houses. Such requirements include achieving privacy through the use of various types of traditional Saudi architectural elements, such as the method of decorative screening of windows, called Mashrabiya, and having an inner courtyard where the house looks inward rather than outward. Other requirements include educating firms on how to design sustainable housing, educating the public on the advantages of sustainable housing and implementing new laws that enforce the utilisation of sustainable methods to housing construction. This paper contributes towards the body of knowledge by proposing initial findings on how to integrate the conservative Islamic culture of Saudi Arabia into the design of a sustainable house specifically for mid and low-income families. This contribution can be implemented on developing countries in the region that are faced with housing shortage for mid and low-income families.

“Yarning” as a method for community-based health research with indigenous women : the indigenous women's wellness research program

This project explores yarning as a methodology for understanding health and wellness from an indigenous woman's perspective. Previous research exploring indigenous Australian women's perspectives have used traditional Western methodologies and have often been felt by the women themselves to be inappropriate and ineffective in gathering information and promoting discussion. This research arose from the indigenous women themselves, and resulted in the exploration of using yarning as a methodology. Yarning is a conversational process that involves the sharing of stories and the development of knowledge. It prioritizes indigenous ways of communicating, in that it is culturally prescribed, cooperative, and respectful. The authors identify different types of yarning that are relevant throughout their research, and explain two types of yarning—family yarning and cross-cultural yarning—which have not been previously identified in research literature. This project found that yarning as a research method is appropriate for community-based health research with indigenous Australian women. This may be an important finding for health professionals and researchers to consider when working and researching with indigenous women from other countries.

A data mining driven crash risk profiling method for road asset management

This thesis takes a new data mining approach for analyzing road/crash data by developing models for the whole road network and generating a crash risk profile. Roads with an elevated crash risk due to road surface friction deficit are identified. The regression tree model, predicting road segment crash rate, is applied in a novel deployment coined regression tree extrapolation that produces a skid resistance/crash rate curve. Using extrapolation allows the method to be applied across the network and cope with the high proportion of missing road surface friction values. This risk profiling method can be applied in other domains.