Controlling microencapsulation and release of micronized proteins using poly(ethylene glycol) and electrospraying

The fabrication of tailored microparticles for delivery of therapeutics is a challenge relying upon a complex interplay between processing parameters and materials properties. The emerging use of electrospraying allows better tailoring of particle morphologies and sizes than current techniques, critical to reproducible release profiles. While dry encapsulation of proteins is essential for the release of active therapeutics from microparticles, it is currently uncharacterized in electrospraying. To this end, poly(ethylene glycol) (PEG) was assessed as a micronizing and solubilizing agent for dry protein encapsulation and release from electrosprayed particles made from polycaprolactone (PCL). The physical effect of PEG in protein-loaded poly(lactic-co-glycolic acid) (PLGA) particles was also studied, for comparison. The addition of 5–15 wt% PEG 6 kDa or 35 kDa resulted in reduced PCL particle sizes and broadened distributions, which could be improved by tailoring the electrospraying processing parameters, namely by reducing polymer concentration and increasing flow rate. Upon micronization, protein particle size was reduced to the micrometer domain, resulting in homogenous encapsulation in electrosprayed PCL microparticles. Microparticle size distributions were shown to be the most determinant factor for protein release by diffusion and allowed specific control of release patterns.

Low-phosporous nickel-coated carbon microcoils : Controlling microstructure through an electroless plating process

Carbon microcoils (CMCs) have been coated with a nickel-phosphorus (Ni-P) film using an electroless plating process, with sodium hypophosphite as a reducing agent in an alkaline bath. CMC composites have potential applications as microwave absorption materials. The morphology, elemental composition and phases in the coating layer of the CMCs and Ni-coated CMCs were investigated by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The effects of process parameters such as pH, temperature and coating time of the plating bath on the phosphorus content and deposition rate of the electroless Ni-P coating were studied. The results revealed that a continuous, uniform and low-phosphorous nickel coating was deposited on the surface of the CMCs for 20 min at pH 9.0, plating bath temperature 70 °C. The as-deposited coatings with approximately 4.5 wt.% phosphorus were found to consist of a mix of nano- and microcrystalline phases. The mean particle size of Ni-P nanoparticles on the outer surface of the CMCs was around 11.9 nm. The deposition rate was found to moderately increase with increasing pH, whereas, the phosphorous content of the deposit exhibited a significant decrease. Moreover, the material of the coating underwent a phase transition between an amorphous and a crystalline structure. The thickness of the deposit and the deposition rate may be controlled through careful variation of the coating time and plating bath temperature.

Two-surface wave decay : controlling power transfer in plasma-surface interactions

Controlled interaction of high-power pulsed electromagnetic radiation with plasma-exposed solid surfaces is a major challenge in applications spanning from electron beam accelerators in microwave electronics to pulsed laser ablation-assisted synthesis of nanomaterials. It is shown that the efficiency of such interaction can be potentially improved via an additional channel of wave power dissipation due to nonlinear excitation of two counterpropagating surface waves, resonant excitations of the plasma-solid system.Physics.

Controlling current and voltage type interfaces in power-hardware-in-the-loop simulations

The usual practice to study a large power system is through digital computer simulation. However, the impact of large scale use of small distributed generators on a power network cannot be evaluated strictly by simulation since many of these components cannot be accurately modelled. Moreover, the network complexity makes the task of practical testing on a physical network nearly impossible. This study discusses the paradigm of interfacing a real-time simulation of a power system to real-life hardware devices. This type of splitting a network into two parts and running a real-time simulation with a physical system in parallel is usually termed as power-hardware-in-the-loop (PHIL) simulation. The hardware part is driven by a voltage source converter that amplifies the signals of the simulator. In this paper, the effects of suitable control strategy on the performance of PHIL and the associated stability aspects are analysed in detail. The analyses are validated through several experimental tests using an real-time digital simulator.

Controlling electronic and adiabatic isolation of quantum dots from the substrate : an ionization-energy theoretic study

Recent controversy on the quantum dots dephasing mechanisms (between pure and inelastic) is re-examined by isolating the quantum dots from their substrate by using the appropriate limits of the ionization energy theory and the quantum adiabatic theorem. When the phonons in the quantum dots are isolated adiabatically from the phonons in the substrate, the elastic or pure dephasing becomes the dominant mechanism. On the other hand, for the case where the phonons from the substrate are non-adiabatically coupled to the quantum dots, the inelastic dephasing process takes over. This switch-over is due to different elemental composition in quantum dots as compared to its substrate. We also provide unambiguous analysis as to understand why GaAs/AlGaAs quantum dots may only have pure dephasing while InAs/GaAs quantum dots give rise to the inelastic dephasing as the dominant mechanism. It is shown that the elemental composition plays an important role (of both quantum dots and substrate) in evaluating the dephasing mechanisms of quantum dots.

Global outsourcing, production and logistics

Supply chains are the core of most industrial networks in which your business operates. They provide the pipeline through which the products and services flow from supplier to customer across each element within the business activity system. Global supply chain relationships have become the basis for many industries with an international network of firms engaged in the supply of goods and services that must be produced to quality standards in one country and delivered just-in-time for assembly or integration into further production processes in another country, frequently many thousands of miles apart. This topic examines the nature of supply chain management and their role in strategic networking. The previous learning tasks have focused on having the correct internal mechanism to effectively manage the inputs and outputs of the organisation by implementing an effective and transparent management system. This learning task takes a look at how management intent strategy and innovation are used to measure the external factors that influence the overall performance of the organisation and develop new strategies by understanding the business cycle and the people within your market environment.

Controlling the surface roughness of epitaxial SiC on silicon

The surface of cubic silicon carbide (3C-SiC) hetero-epitaxial films grown on the (111) surface of silicon is a promising template for the subsequent epitaxial growth of III-V semiconductor layers and graphene. We investigate growth and post-growth approaches for controlling the surface roughness of epitaxial SiC to produce an optimal template. We first explore 3C-SiC growth on various degrees of offcut Si(111) substrates, although we observe that the SiC roughness tends to worsen as the degree of offcut increases. Hence we focus on post-growth approaches available on full wafers, comparing chemical mechanical polishing (CMP) and a novel plasma smoothening process. The CMP leads to a dramatic improvement, bringing the SiC surface roughness down to sub-nanometer level, though removing about 200 nm of the SiC layer. On the other hand, our proposed HCl plasma process appears very effective in smoothening selectively the sharpest surface topography, leading up to 30% improvement in SiC roughness with only about 50 nm thickness loss. We propose a simple physical model explaining the action of the plasma smoothening.

Insurance and transport law : controlling insurance contract terms : Section 54 of the Insurance Contracts Act – compliance, recovery and accountability

Commonwealth legislation covering insurance contracts contains numerous provisions designed to control the operation and effect of terms in life and general insurance contracts. For example, the Life Insurance Act 1995 (Cth) contains provisions regulating the consequences attendant upon incorrect statements in proposals [1] and non-payment of premiums, [2] provides that an insurer may only exclude liability in the case of suicide if it has made express provision for such contingency in its policy, [3] and severely restricts the efficacy of conditions as to war risks. [4] The Insurance Contracts Act 1984 (Cth) is even more intrusive and has a major impact upon contractual provisions in the general insurance field. It is beyond the scope of this note to explore all of these provisions in any detail but examples of controls and constraints imposed upon the operation and effect of contractual provisions include the following. A party is precluded from relying upon a provision in a contract of insurance if such reliance would amount to a failure to act with the utmost good faith. [5] Similarly, a policy provision which requires differences or disputes arising out of the insurance to be submitted to arbitration is void, [6] unless the insurance is a genuine cover for excess of loss over and above another specified insurance. [7] Similarly clause such as conciliation clauses, [8] average clauses, [9] and unusual terms [10] are given qualified operation. [11] However the provision in the Insurance Contracts Act that has the greatest impact upon, and application to, a wide range of insurance clauses and claims is s 54. This section has already generated a significant volume of case law and is the focus of this note. In particular this note examines two recent cases. The first, Johnson v Triple C Furniture and Electrical Pty Ltd [2012] 2 Qd R 337, (hereafter the Triple C case), is a decision of the Queensland Court of Appeal; and the second, Matthew Maxwell v Highway Hauliers Pty Ltd [2013] WASCA 115, (hereafter the Highway Hauliers case), is a decision of the Court of Appeal in Western Australia. This latter decision is on appeal to the High Court of Australia. The note considers too the decision of the New South Wales Court of Appeal in Prepaid Services Pty Ltd v Atradius Credit Insurance NV [2013] NSWCA 252 (hereafter the Prepaid Services case).These cases serve to highlight the complex nature of s 54 and its application, as well as the difficulty in achieving a balance between an insurer and an insured's reasonable expectations.

Association between Australian-Indian mothers' controlling feeding practices and children's appetite traits

This cross-sectional study examined the association between controlling feeding practices and children's appetite traits. The secondary aim studied the relationship between controlling feeding practices and two proxy indicators of diet quality. Participants were 203 Australian-Indian mothers with children aged 1-5 years. Controlling feeding practices (pressure to eat, restriction, monitoring) and children's appetite traits (. food approach traits: food responsiveness, enjoyment of food, desire to drink, emotional overeating; food avoidance traits: satiety responsiveness, slowness in eating, fussiness and emotional undereating) were measured using self-reported, previously validated scales/questionnaires. Children's daily frequency of consumption of core and non-core foods was estimated using a 49-item list of foods eaten (yes/no) in the previous 24 hours as an indicator of diet quality. Higher pressure to eat was associated with higher scores for satiety responsiveness, slowness in eating, fussiness and lower score for enjoyment of food. Higher restriction was related to higher scores for food responsiveness and emotional overeating. Higher monitoring was inversely associated with fussiness, slowness in eating, food responsiveness and emotional overeating and positively associated with enjoyment of food. Pressure to eat and monitoring were related to lower number of core and non-core foods consumed in the previous 24 hours, respectively. All associations remained significant after adjusting for maternal and child covariates (n = 152 due to missing data). In conclusion, pressure to eat was associated with higher food avoidance traits and lower consumption of core foods. Restrictive feeding practices were associated with higher food approach traits. In contrast, monitoring practices were related to lower food avoidance and food approach traits and lower non-core food consumption.

The relationship between controlling feeding practices and boys’ and girls’ eating in the absence of hunger

Parental controlling feeding practices have been directly associated with maladaptive child eating behaviours, such as Eating in the Absence of Hunger (EAH). The aim of this study was to examine EAH in very young children (3-4 years old) and to investigate the association between maternal controlling feeding practices and energy intake from a standardised selection of snacks consumed ‘in the absence of hunger’. Thirty-seven mother-child dyads enrolled in the NOURISH RCT participated in a modified EAH protocol conducted in the child’s home. All children displayed EAH, despite 80% reporting to be full or very full following completion of lunch 15 minutes earlier. The relationship between maternal and child covariates and controlling feeding practices and EAH were examined using non-parametric tests, and were stratified by child gender. For boys only, pressure to eat was positively associated with EAH. Neither restriction nor monitoring practices were associated with EAH in either boys or girls. Overall, the present findings suggest gender differences in the relationship between maternal feeding practices and children’s eating behaviours emerge early and should be considered in future research and intervention design.

A model for assessing information systems success and its application to e-logistics tracking systems

The DeLone and McLean (D&M) model (2003) has been broadly used and generally recognised as a useful model for gauging the success of IS implementations. However, it is not without limitations. In this study, we evaluate a model that extends the D&M model and attempts to address some of it slimitations by providing a more complete measurement model of systems success. To that end, we augment the D&M (2003) model and include three variables: business value, institutional trust, and future readiness. We propose that the addition of these variables allows systems success to be assessed at both the systems level and the business level. Consequently, we develop a measurement model rather than a structural or predictive model of systems success.

Are Individualism and “Masculinity” Related When Controlling for Regional Proximity? A Reappraisal of Barry (2015)

Barry recently attributed the non-significant relationship between the cultural dimensions of Individualism (IND) and Masculinity (MASC) to a suppression effect of regional differences. Pairing countries on regional proximity, he showed that a strong correlation between these cultural dimensions emerged. However, we point to significant issues with this analysis, including how countries were paired, ordered, and included/excluded, as well as in the cultural meaningfulness of regional proximity. Re-analysis of the data after addressing these issues shows that IND and MASC were not significantly related at a cultural level after controlling for regional proximity, nor after controlling for two other prominent geographic factors: latitude and climate demands. The weight of evidence suggests that IND and MASC are not correlated at a cultural level.

Identification of major loci controlling clinical manifestations of ankylosing spondylitis

Objective. To identify genomic regions linked with determinants of age at symptom onset, disease activity, and functional impairment in ankylosing spondylitis (AS). Methods. A whole genome linkage scan was performed in 188 affected sibling pair families with 454 affected individuals. Traits assessed were age at symptom onset, disease activity assessed by the Bath Ankylosing Spondylitis Disease Activity Index (BASDAI), and functional impairment assessed by the Bath Ankylosing Spondylitis Functional Index (BASFI). Parametric and nonparametric quantitative linkage analysis was performed using parameters defined in a previous segregation study. Results. Heritabilities of the traits studied in this data set were as follows: BASDAI 0.49 (P = 0.0001, 95% confidence interval [95% CI] 0.23-0.75), BASFI 0.76 (P = 10-7, 95% CI 0.49-1.0), and age at symptom onset 0.33 (P = 0.005, 95% CI 0.04-0.62). No linkage was observed between the major histocompatibility complex (MHC) and any of the traits studied (logarithm of odds [LOD] score <1.0). "Significant" linkage (LOD score 4.0) was observed between a region on chromosome 18p and the BASDAI. Age at symptom onset showed "suggestive" linkage to chromosome 11p (LOD score 3.3). Maximum linkage with the BASFI was seen at chromosome 2q (LOD score 2.9). Conclusion. In contrast to the genetic determinants of susceptibility to AS, clinical manifestations of the disease measured by the BASDAI, BASFI, and age at symptom onset are largely determined by a small number of genes not encoded within the MHC.

Exposure risk assessment and evaluation of the best management practice for controlling pesticide runoff from paddy fields. Part 2: Model simulation for the herbicide pretilachlor

BACKGROUND: Monitoring studies revealed high concentrations of pesticides in the drainage canal of paddy fields. It is important to have a way to predict these concentrations in different management scenarios as an assessment tool. A simulation model for predicting the pesticide concentration in a paddy block (PCPF-B) was evaluated and then used to assess the effect of water management practices for controlling pesticide runoff from paddy fields. RESULTS: The PCPF-B model achieved an acceptable performance. The model was applied to a constrained probabilistic approach using the Monte Carlo technique to evaluate the best management practices for reducing runoff of pretilachlor into the canal. The probabilistic model predictions using actual data of pesticide use and hydrological data in the canal showed that the water holding period (WHP) and the excess water storage depth (EWSD) effectively reduced the loss and concentration of pretilachlor from paddy fields to the drainage canal. The WHP also reduced the timespan of pesticide exposure in the drainage canal. CONCLUSIONS: It is recommended that: (1) the WHP be applied for as long as possible, but for at least 7 days, depending on the pesticide and field conditions; (2) an EWSD greater than 2 cm be maintained to store substantial rainfall in order to prevent paddy runoff, especially during the WHP.