An evaluation of alternative media for pebble matrix filtration using clay balls and recycled crushed glass

Protecting slow sand filters (SSFs) from high-turbidity waters by pretreatment using pebble matrix filtration (PMF) has previously been studied in the laboratory at University College London, followed by pilot field trials in Papua New Guinea and Serbia. The first full-scale PMF plant was completed at a water-treatment plant in Sri Lanka in 2008, and during its construction, problems were encountered in sourcing the required size of pebbles and sand as filter media. Because sourcing of uniform-sized pebbles may be problematic in many countries, the performance of alternative media has been investigated for the sustainability of the PMF system. Hand-formed clay balls made at a 100-yearold brick factory in the United Kingdom appear to have satisfied the role of pebbles, and a laboratory filter column was operated by using these clay balls together with recycled crushed glass as an alternative to sand media in the PMF. Results showed that in countries where uniform-sized pebbles are difficult to obtain, clay balls are an effective and feasible alternative to natural pebbles. Also, recycled crushed glass performed as well as or better than silica sand as an alternative fine media in the clarification process, although cleaning by drainage was more effective with sand media. In the tested filtration velocity range of ð0:72–1:33Þ m=h and inlet turbidity range of (78–589) NTU, both sand and glass produced above 95% removal efficiencies. The head loss development during clogging was about 30% higher in sand than in glass media.

Court-provided trial technology : efficiency and fairness for criminal trials

In Australia, trials conducted as 'electronic trials' have ordinarily run with the assistance of commercial service providers, with the associated costs being borne by the parties. However, an innovative approach has been taken by the courts in Queensland. In October 2007 Queensland became the first Australian jurisdiction to develop its own court-provided technology, to facilitate the conduct of an electronic trial. This technology was first used in the conduct of civil trials. The use of the technology in the civil sphere highlighted its benefits and, more significantly, demonstrated the potential to achieve much greater efficiencies. The Queensland courts have now gone further, using the court-provided technology in the high proffle criminal trial of R v Hargraves, Hargraves and Stoten, in which the three accused were tried for conspiracy to defraud the Commonwealth of Australia of about $3.7 million in tax. This paper explains the technology employed in this case and reports on the perspectives of all of the participants in the process. The representatives for all parties involved in this trial acknowledged, without reservation, that the use of the technology at trial produced considerable overall efficiencies and costs savings. The experience in this trial also demonstrates that the benefits of trial technology for the criminal justice process are greater than those for civil litigation. It shows that, when skilfully employed, trial technology presents opportunities to enhance the fairness of trials for accused persons. The paper urges governments, courts and the judiciary in all jurisdictions to continue their efforts to promote change, and to introduce mechanisms to facilitate more broadly a shift from the entrenched paper-based approach to both criminal and civil procedure to one which embraces more broadly the enormous benefits trial technology has to offer.

Focusing on patients : differences between the practice of expert and non-expert nephrology nurses

Specialisation in nursing enables a nurse to focus, in much greater depth, on the requisite knowledge and skills for providing patients with the best possible care. Nephrology nursing is one such area where specialisation has evolved. The characteristic focus of practice emerged as an important feature during a study into the process of expertise acquisition in nephrology nursing practice. Using grounded theory methodology, this study involved 6 non-expert and 11 expert nurses and took place in one renal unit in New South Wales. Nephrology nursing practice was observed for 103 hours, and this was immediately followed by semi-structured interviews. The characteristic of focus was conceptualised as the nurses' centre of attention or concentration while they were undertaking nursing activities. Focus ranged from inexperienced non-expert nurses concentrating predominantly on the immediate task at hand, experienced non-expert nurses who focussed on the medium term to expert nurses who viewed actions (and their possible consequences) more broadly and in the longer term. Of significance to nursing, is how nephrology nurses alter their focus of practice as they acquire and exercise their developing expertise in this specialty.

CDA and values : interdisciplinarity as a critical turn

From their very outset, the disciplines of social science have claimed a need for interdisciplinarity. Proponents of new disciplines have also claimed the whole of human activity as their domain, whilst simultaneously emphasising the need for increased specialisation. Critical social analysis attempts to repair the flaws of specialisation. In this chapter, I argue that the trend towards academic specialisation in social science is most usefully viewed from the perspective of evaluative meaning, and that each new discipline, in emphasising one aspect of a broken conception of humanity, necessarily emphasises one aspect of an already broken conception of value. Critical discourse analysis, qua critical social analysis, may therefore benefit by firstly proceeding from the perspective of evaluative meaning to understand the dynamics of social change and overcome the challenges posed by centuries of intensive specialisation in social science.

Understanding nonsense : breathing life into shibboleths and killing critical thought in higher education

In this paper, I focus on the growing "nonsense industry" which is most apparent in the writing typical of business, government departments, and the financial press. This writing, like technical writing, is characterised by heavy reliance on grammatical metaphor. It endows shibboleths - for instance, "globalisation"; "efficiencies"; "competition"; "modernisation"; "consumer sentiment"; "reform"; and so on - with anthropomorphic qualities. These anthropomorphic artefacts of technocratised language are then presented as having immutable powers over people. Thus they become banal public excuses for negligent practices in both business and government.

From go to woe : how a not-for-profit managed the change to accrual accounting

Purpose – The aim of this paper is to examine the process of change in an Australian not-for-profit organization, from a cash-based to an accrual-based accounting system. Its particular focus is the relationship between the image portrayed by accrual accounting adoption and the technical realities of the new system. Design/methodology/approach – Data were gathered from interviews, documents and meetings, and were contextualized and interpreted using institutional theory. Findings – The decision to change to accrual accounting was made at the top of the organizational hierarchy in response to institutional pressure to present a corporate image. The implementation of the new system was poorly conceived, inadequately resourced, and hampered by an authoritarian structure that effectively ignored the technical incompetence and training needs of many accounting staff. This resulted in an accounting system half way between cash and accrual, and very different from the system as it had been promoted. The process caused conflict at all levels of the organizational hierarchy. Research limitations/implications – Accounting in not-for-profit organizations is an under-researched area offering potential for fruitful research in a changing institutional landscape. This institutional approach, while offering just one interpretation of the qualitative data gathered in this project, provides valuable insights about the process of change. Practical implications – Not-for-profit organizations play a vital economic and social role, and need carefully to assess their responses to ongoing institutional pressures. In implementing change, they face the challenge of balancing the promotion of an institutionally acceptable image and the need for technical efficiencies. Originality/value – The examination of change in an organization provides a rich context for the exploration of the dynamic, problematic process by which a new accounting practice is embedded and institutionalized. Keywords Institutional theory, Not-for-profit organizations, Accrual accounting, Change process, Qualitative research, Change management, Decision making, Training needs, Australia Paper type Research paper

Characteristics of modal sound radiation of finite cylindrical shells

Characteristics of modal sound radiation of finite cylindrical shells are studied using finite element and boundary element methods in this paper. In the low frequency range, modal radiation efficiencies of finite cylindrical shells are found to asymptotically approach those of the corresponding infinite cylindrical shell when structural trace wavelengths of the cylindrical shells are greater than the acoustic wavelength. Modal radiation efficiencies for each group of modes having the same circumferential modal index decrease as the axial modal index increases. They converge to each other when the axial trace wavelength is much greater than the circumferential trace wavelength. The mechanism leading to lower radiation efficiency of modes with higher circumferential modal index of short cylinders is explained. Similar to those of flat plate panels, change in slope or waviness is observed in modal radiation efficiency curves of modes with higher order axial modal index at medium frequencies. This is attributed to the interference of sound radiated by neighbouring vibrating cells when the distance between nodal lines of a vibrating mode is in the same order or smaller than the acoustic wavelength. Effects of the internal sound field on modal radiation efficiencies of a finite open-end cylinder are discussed.

N-Aryl stilbazolium dyes as sensitizers for solar cells

Eight new N-arylstilbazolium chromophores with electron donating –NR2 (R = Me or Ph) substituents have been synthesized via Knoevenagel condensations and isolated as their PF6− salts. These compounds have been characterized by using various techniques including 1H NMR and IR spectroscopies and electrospray mass spectrometry. UV–vis absorption spectra recorded in acetonitrile are dominated by intense, low energy π → π* intramolecular charge-transfer (ICT) bands, and replacing Me with Ph increases the ICT energies. Cyclic voltammetric studies show irreversible reduction processes, together with oxidation waves that are irreversible for R = Me, but reversible for R = Ph. Single crystal X-ray structures have been determined for three of the methyl ester-substituted stilbazolium salts and for the Cl− salts of their picolinium precursors. Time-dependent density functional theory calculations afford reasonable predictions of ICT energies, but greater rigour is necessary for –NPh2 derivatives. The four new acid-functionalized dyes give moderate sensitization efficiencies (ca. 0.2%) when using TiO2-based photoanodes, with relatively higher values for R = Ph vs Me, while larger efficiencies (up to 0.8%) are achieved with ZnO substrates.

Physical characteristics of small ions and their interaction with ultrafine particles in the urban environment

In recent years, the effect of ions and ultrafine particles on ambient air quality and human health has been well documented, however, knowledge about their sources, concentrations and interactions within different types of urban environments remains limited. This thesis presents the results of numerous field studies aimed at quantifying variations in ion concentration with distance from the source, as well as identifying the dynamics of the particle ionisation processes which lead to the formation of charged particles in the air. In order to select the most appropriate measurement instruments and locations for the studies, a literature review was also conducted on studies that reported ion and ultrafine particle emissions from different sources in a typical urban environment. The initial study involved laboratory experiments on the attachment of ions to aerosols, so as to gain a better understanding of the interaction between ions and particles. This study determined the efficiency of corona ions at charging and removing particles from the air, as a function of different particle number and ion concentrations. The results showed that particle number loss was directly proportional to particle charge concentration, and that higher small ion concentrations led to higher particle deposition rates in all size ranges investigated. Nanoparticles were also observed to decrease with increasing particle charge concentration, due to their higher Brownian mobility and subsequent attachment to charged particles. Given that corona discharge from high voltage powerlines is considered one of the major ion sources in urban areas, a detailed study was then conducted under three parallel overhead powerlines, with a steady wind blowing in a perpendicular direction to the lines. The results showed that large sections of the lines did not produce any corona at all, while strong positive emissions were observed from discrete components such as a particular set of spacers on one of the lines. Measurements were also conducted at eight upwind and downwind points perpendicular to the powerlines, spanning a total distance of about 160m. The maximum positive small and large ion concentrations, and DC electric field were observed at a point 20 m downwind from the lines, with median values of 4.4×103 cm-3, 1.3×103 cm-3 and 530 V m-1, respectively. It was estimated that, at this point, less than 7% of the total number of particles was charged. The electrical parameters decreased steadily with increasing downwind distance from the lines but remained significantly higher than background levels at the limit of the measurements. Moreover, vehicles are one of the most prevalent ion and particle emitting sources in urban environments, and therefore, experiments were also conducted behind a motor vehicle exhaust pipe and near busy motorways, with the aim of quantifying small ion and particle charge concentration, as well as their distribution as a function of distance from the source. The study found that approximately equal numbers of positive and negative ions were observed in the vehicle exhaust plume, as well as near motorways, of which heavy duty vehicles were believed to be the main contributor. In addition, cluster ion concentration was observed to decrease rapidly within the first 10-15 m from the road and ion-ion recombination and ion-aerosol attachment were the most likely cause of ion depletion, rather than dilution and turbulence related processes. In addition to the above-mentioned dominant ion sources, other sources also exist within urban environments where intensive human activities take place. In this part of the study, airborne concentrations of small ions, particles and net particle charge were measured at 32 different outdoor sites in and around Brisbane, Australia, which were classified into seven different groups as follows: park, woodland, city centre, residential, freeway, powerlines and power substation. Whilst the study confirmed that powerlines, power substations and freeways were the main ion sources in an urban environment, it also suggested that not all powerlines emitted ions, only those with discrete corona discharge points. In addition to the main ion sources, higher ion concentrations were also observed environments affected by vehicle traffic and human activities, such as the city centre and residential areas. A considerable number of ions were also observed in a woodland area and it is still unclear if they were emitted directly from the trees, or if they originated from some other local source. Overall, it was found that different types of environments had different types of ion sources, which could be classified as unipolar or bipolar particle sources, as well as ion sources that co-exist with particle sources. In general, fewer small ions were observed at sites with co-existing sources, however particle charge was often higher due to the effect of ion-particle attachment. In summary, this study quantified ion concentrations in typical urban environments, identified major charge sources in urban areas, and determined the spatial dispersion of ions as a function of distance from the source, as well as their controlling factors. The study also presented ion-aerosol attachment efficiencies under high ion concentration conditions, both in the laboratory and in real outdoor environments. The outcomes of these studies addressed the aims of this work and advanced understanding of the charge status of aerosols in the urban environment.

Optical and microscopic study of a polymer-nanotube mixture for organic photovoltaic applications

Organic solar cells based on bulk heterojunction between a conductive polymer and a carbon nanostructure offer potential advantages compared to conventional inorganic cells. Low cost, light weight, flexibility and high peak power per unit weight are all features that can be considered a reality for organic photovoltaics. Although polymer/carbon nanotubes solar cells have been proposed, only low power conversion efficiencies have been reached without addressing the mechanisms responsible for this poor performance. The purpose of this work is therefore to investigate the basic interaction between carbon nanotubes and poly(3-hexylthiophene) in order to demonstrate how this interaction affects the performance of photovoltaic devices. The outcomes of this study are the contributions made to the knowledge of the phenomena explaining the behaviour of electronic devices based on carbon nanotubes and poly(3-hexylthiophene). In this PhD, polymer thin films with the inclusion of uniformly distributed carbon nanotubes were deposited from solution and characterised. The bulk properties of the composites were studied with microscopy and spectroscopy techniques to provide evidence of higher degrees of polymer order when interacting with carbon nanotubes. Although bulk investigation techniques provided useful information about the interaction between the polymer and the nanotubes, clear evidence of the phenomena affecting the heterojunction formed between the two species was investigated at nanoscale. Identifying chirality-driven polymer assisted assembly on the carbon nanotube surface was one of the major achievements of this study. Moreover, the analysis of the electrical behaviour of the heterojunction between the polymer and the nanotube highlighted the charge transfer responsible for the low performance of photovoltaic devices. Polymer and carbon nanotube composite-based devices were fabricated and characterised in order to study their electronic properties. The carbon nanotube introduction in the polymer matrix evidenced a strong electrical conductivity enhancement but also a lower photoconductivity response. Moreover, the extension of pristine polymer device characterisation models to composites based devices evidenced the conduction mechanisms related to nanotubes. Finally, the introduction of carbon nanotubes in the polymer matrix was demonstrated to improve the pristine polymer solar cell performance and the spectral response even though the power conversion efficiency is still too low.

Structural behaviour and design of cold-formed steel wall systems under fire conditions

In recent times, light gauge steel framed (LSF) structures, such as cold-formed steel wall systems, are increasingly used, but without a full understanding of their fire performance. Traditionally the fire resistance rating of these load-bearing LSF wall systems is based on approximate prescriptive methods developed based on limited fire tests. Very often they are limited to standard wall configurations used by the industry. Increased fire rating is provided simply by adding more plasterboards to these walls. This is not an acceptable situation as it not only inhibits innovation and structural and cost efficiencies but also casts doubt over the fire safety of these wall systems. Hence a detailed fire research study into the performance of LSF wall systems was undertaken using full scale fire tests and extensive numerical studies. A new composite wall panel developed at QUT was also considered in this study, where the insulation was used externally between the plasterboards on both sides of the steel wall frame instead of locating it in the cavity. Three full scale fire tests of LSF wall systems built using the new composite panel system were undertaken at a higher load ratio using a gas furnace designed to deliver heat in accordance with the standard time temperature curve in AS 1530.4 (SA, 2005). Fire tests included the measurements of load-deformation characteristics of LSF walls until failure as well as associated time-temperature measurements across the thickness and along the length of all the specimens. Tests of LSF walls under axial compression load have shown the improvement to their fire performance and fire resistance rating when the new composite panel was used. Hence this research recommends the use of the new composite panel system for cold-formed LSF walls. The numerical study was undertaken using a finite element program ABAQUS. The finite element analyses were conducted under both steady state and transient state conditions using the measured hot and cold flange temperature distributions from the fire tests. The elevated temperature reduction factors for mechanical properties were based on the equations proposed by Dolamune Kankanamge and Mahendran (2011). These finite element models were first validated by comparing their results with experimental test results from this study and Kolarkar (2010). The developed finite element models were able to predict the failure times within 5 minutes. The validated model was then used in a detailed numerical study into the strength of cold-formed thin-walled steel channels used in both the conventional and the new composite panel systems to increase the understanding of their behaviour under nonuniform elevated temperature conditions and to develop fire design rules. The measured time-temperature distributions obtained from the fire tests were used. Since the fire tests showed that the plasterboards provided sufficient lateral restraint until the failure of LSF wall panels, this assumption was also used in the analyses and was further validated by comparison with experimental results. Hence in this study of LSF wall studs, only the flexural buckling about the major axis and local buckling were considered. A new fire design method was proposed using AS/NZS 4600 (SA, 2005), NAS (AISI, 2007) and Eurocode 3 Part 1.3 (ECS, 2006). The importance of considering thermal bowing, magnified thermal bowing and neutral axis shift in the fire design was also investigated. A spread sheet based design tool was developed based on the above design codes to predict the failure load ratio versus time and temperature for varying LSF wall configurations including insulations. Idealised time-temperature profiles were developed based on the measured temperature values of the studs. This was used in a detailed numerical study to fully understand the structural behaviour of LSF wall panels. Appropriate equations were proposed to find the critical temperatures for different composite panels, varying in steel thickness, steel grade and screw spacing for any load ratio. Hence useful and simple design rules were proposed based on the current cold-formed steel structures and fire design standards, and their accuracy and advantages were discussed. The results were also used to validate the fire design rules developed based on AS/NZS 4600 (SA, 2005) and Eurocode Part 1.3 (ECS, 2006). This demonstrated the significant improvements to the design method when compared to the currently used prescriptive design methods for LSF wall systems under fire conditions. In summary, this research has developed comprehensive experimental and numerical thermal and structural performance data for both the conventional and the proposed new load bearing LSF wall systems under standard fire conditions. Finite element models were developed to predict the failure times of LSF walls accurately. Idealized hot flange temperature profiles were developed for non-insulated, cavity and externally insulated load bearing wall systems. Suitable fire design rules and spread sheet based design tools were developed based on the existing standards to predict the ultimate failure load, failure times and failure temperatures of LSF wall studs. Simplified equations were proposed to find the critical temperatures for varying wall panel configurations and load ratios. The results from this research are useful to both structural and fire engineers and researchers. Most importantly, this research has significantly improved the knowledge and understanding of cold-formed LSF loadbearing walls under standard fire conditions.

Corporate profit and impression management in developing markets

In this study, we examine how organisations in Fiji communicate or legitimise their profit. We base the need for understanding this phenomenon on the following premise. Organisations are part of a wider society, and in competition for scarce resources. Organisations obtain the rights to consume resources upon conception, but must continually legitimise their rights of existence and the need to access the resources. Legitimacy is the ability to continue to justify one’s authority to exist in a society. Organisations rights to resources are contractual, and have a moral obligation to act in a responsible manner and justify their outcomes, actions, and activities to external stakeholders. Such justifications would be an attempt at legitimizing their existence by some form of impression management. Impression management refers to the process by which individuals attempt to influence the impression of others (Melo et al. 2009). In corporate reporting, impression management occurs when management selects, display, and presents that information in a manner that distorts readers’ perceptions of corporate achievements (Neu 1991; Patten 2002), and is managed best through disclosures (O’Donovan 2002). In developing economies, there is significant Government protection that creates near-monopoly sectors and industries. The rendered protection permits organisations to provide essential services to the community at reasonable costs. Organisations in these sectors and industries have an ominous need to legitimise their position and actions. The bond between the organisations and the society is much stronger, making organisations devote more effort in communicating their activities. Protection permits organisations to make reasonable profits to sustain their operations. Society may not accept abnormal profits from operational efficiencies. Profit is fundamental to the society’s perception of an organisation, amplifying the need for the firm to justify a level of profit. Abnormal profit for organisations construes bad news, and organisations would make relevant disclosures to manage stakeholder impressions on profit (Patten 2002). Organisations can manage impressions by disclosing information in a particular way. That is, organisations would want to put the impression that the abnormal profit is justified and the society will obtain its benefits in future. Such form of impression management requires unambiguous disclosure of information. The readability of corporate disclosures is an important indicator of organisational abnormal profit-related legitimacy efforts in developing economies.

Computational design of cyclic nitroxides as efficient redox mediators for dye-sensitized solar cells

Cyclic nitroxide radicals represent promising alternatives to the iodine-based redox mediator commonly used in dye-sensitized solar cells (DSSCs). To date DSSCs with nitroxide-based redox mediators have achieved energy conversion efficiencies of just over 5 % but efficiencies of over 15 % might be achievable, given an appropriate mediator. The efficacy of the mediator depends upon two main factors: it must reversibly undergo one-electron oxidation and it must possess an oxidation potential in a range of 0.600-0.850 V (vs. a standard hydrogen electrode (SHE) in acetonitrile at 25 °C). Herein, we have examined the effect that structural modifications have on the value of the oxidation potential of cyclic nitroxides as well as the reversibility of the oxidation process. These included alterations to the N-containing skeleton (pyrrolidine, piperidine, isoindoline, azaphenalene, etc.), as well as the introduction of different substituents (alkyl-, methoxy-, amino-, carboxy-, etc.) to the ring. Standard oxidation potentials were calculated using high-level ab initio methodology that was demonstrated to be very accurate (with a mean absolute deviation from experimental values of only 16 mV). An optimal value of 1.45 for the electrostatic scaling factor for UAKS radii in acetonitrile solution was obtained. Established trends in the values of oxidation potentials were used to guide molecular design of stable nitroxides with desired E° ox and a number of compounds were suggested for potential use as enhanced redox mediators in DSSCs. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

APS grant enhances educational psychology’s impact in Bangladesh

The APS Grant for Intercultural and/or International Projects of up to $10,000 supports innovative projects that have an intercultural and/or international focus, particularly in countries where psychology is an emerging discipline. Associate Professors Linda Gilmore MAPS and Marilyn Campbell MAPS from Queensland University of Technology were awarded the APS Grant in 2010-11. Their project aimed to promote and advance the profession of psychology in Bangladesh by supporting the newly introduced specialisation of educational psychology. With a population of 159 million in a country only twice the size of Tasmania, Bangladesh is one of the poorest and most densely populated countries in the world. Yet at the time this project commenced, there was only one school psychologist in the entire country. Linda Gilmore shared her experiences and insights about the project with InPsych.