Complex modelling of open system design for sustainable architecture

This paper argues a model of complex system design for sustainable architecture within a framework of entropy evolution. The spectrum of sustainable architecture consists of the efficient use of energy and material resource in life-cycle of buildings, the active involvement of the occupants in micro-climate control within buildings, and the natural environmental context. The interactions of the parameters compose a complex system of sustainable architectural design, of which the conventional linear and fragmented design technologies are insufficient to indicate holistic and ongoing environmental performance. The complexity theory of dissipative structure states a microscopic formulation of open system evolution, which provides a system design framework for the evolution of building environmental performance towards an optimization of sustainability in architecture.

Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Victoria regia's bequest to modern architecture

This paper will explore the relationship between the giant South American waterlily, the Victoria regia (today named Victoria amazonica), and the 1914 Glashaus exposition building by the German architect, Bruno Taut. Starting with a general botanical introduction of Victoria regia, the paper exposes the first European cultivation of the lily by Joseph Paxton at Chatsworth,England, in 1849. Following this initial cultivation, Paxton subsequently develops a specialist greenhouse for the plant, that later becomes the prototype for all Victoria regia greenhouses. However, from about 1860 as Victoria regia cultivation spreads to continental Europe, a greenhouse that differs from Paxton’s prototype subsequently evolves. An investigation of these later continental European greenhouses, coupled with an exposure of Taut’s own writings concerning Victoria regia, reveals startling similarities to the Glashaus, which ultimately reveals the Glashaus as directly inspired by Victoria regia.

Short-term retention of labeled chondrocyte subpopulations in stratified tissue-engineered cartilaginous constructs implanted in vivo in mini-pigs

It is likely that effective application of cell-laden implants for cartilage defects depends on retention of implanted cells and interaction between implanted and host cells. The objectives of this study were to characterize stratified cartilaginous constructs seeded sequentially with superficial (S) and middle (M) chondrocyte subpopulations labelled with fluorescent cell tracking dye PKH26 (*) and determine the degree to which these stratified cartilaginous constructs maintain their architecture in vivo after implantation in mini-pigs for 1 week. Alginate-recovered cells were seeded sequentially to form stratified S*/M (only S cells labelled) and S*/M* (both S and M cells labelled) constructs. Full-thickness defects (4 mm diameter) were created in the patellofemoral groove of adult Yucatan mini-pigs and filled with portions of constructs or left empty. Constructs were characterized biochemically, histologically, and biomechanically, and stratification visualized and quantified, before and after implant. After 1 week, animals were sacrificed and implants retrieved. After 1 week in vivo, glycosaminoglycan and collagen content of constructs remained similar to that at implant, whereas DNA content increased. Histological analyses revealed features of an early repair response, with defects filled with tissues containing little matrix and abundant cells. Some implanted (PKH26-labeled) cells persisted in the defects, although constructs did not maintain a stratified organization. Of the labelled cells, 126 +/- 38% and 32 +/- 8% in S*/M and S*/M* constructs, respectively, were recovered. Distribution of labelled cells indicated interactions between implanted and host cells. Longer-term in vivo studies will be useful in determining whether implanted cells are sufficient to have a positive effect in repair.

Overcoming the complexity of diagnostic problems due to sensor network architecture

In fault detection and diagnostics, limitations coming from the sensor network architecture are one of the main challenges in evaluating a system’s health status. Usually the design of the sensor network architecture is not solely based on diagnostic purposes, other factors like controls, financial constraints, and practical limitations are also involved. As a result, it quite common to have one sensor (or one set of sensors) monitoring the behaviour of two or more components. This can significantly extend the complexity of diagnostic problems. In this paper a systematic approach is presented to deal with such complexities. It is shown how the problem can be formulated as a Bayesian network based diagnostic mechanism with latent variables. The developed approach is also applied to the problem of fault diagnosis in HVAC systems, an application area with considerable modeling and measurement constraints.

Enterprise architecture and the integration of service-oriented architecture

In recent years, enterprise architecture (EA) has captured a growing attention as a means to systematically consolidate and interrelate diverse business and IT artefacts in order to provide holistic decision support. The recent popularity of a service-orientation has added “service “and related constructs as a new element that requires consideration within an Enterprise Architecture. Since the emergence of the Service-Oriented Architecture (SOA), many attempts have been made to incorporate SOA artefacts in existing EA frameworks. Yet, the approaches taken to achieve this goal differ substantially for the most commonly used EA frameworks to date. SOA in the context of enterprise architecture is one of the future research challenges. Several authors argue that further research is needed in order to understand how SOA impacts prior enterprise architecture frameworks. This study explores SOA integration within EA, identifies SOA integration approaches within EA and identifies factors that impact SOA integration within Enterprise Architecture.

A natural model for architecture

In John Frazer's seminal book An Evolutionary Architecture (1995), from which this essay is extracted, a fundamental approach is established for have natural systems can unfold mechanisms for negotiating the complex design space inherent in architectural systems. In this essay, which forms a critical part of the book, Frazer draws both correlations and distinctions from natural processes as emulated in design processes and form as active manifestations within natural systems. Form is seen as an evolving agent generated via the rules of descriptive genetic coding, functioning as a part of a metabolic environment. Frazer's process-model establishes the realm in which computation must manoeuvre to produce a valid solution space, including the operations of self-organisation, complexity and emergent behaviour. Addressing design as an authored practice, he extends the transference of 'creativity' from the explicit impression into form, to the investment of though, organisation and strategy in the computational processes which produce form. Frazer's text concentrates astutely on the practising of the evolutionary paradigm, the output of which postulates an architecture born of the relationships to dynamic environmental and socio-economic contexts, and realised through morphogenetic materialisation.

Performance evaluation of eight contemporary passive solar homes in subtropical Australia

Subtropical south-east Queensland’s expanding population is expected to lead to a demand for an additional 754,000 dwellings by 2031. A legacy of poor housing design, minimal building regulations, an absence of building performance evaluation and various social and market factors has lead to a high and growing penetration of, and reliance on, air conditioners to provide comfort in this relatively benign climate. This reliance impacts on policy goals to adapt to and mitigate against global warming, electricity infrastructure investment and household resilience. Based on the concept of bioclimatic design, this field study scrutinizes eight non-air conditioned homes to develop a deeper understanding of the role of contemporary passive solar architecture in the delivery of thermally comfortable and resilient homes in the subtropics. These homes were found to provide inhabitants with an acceptable level of thermal comfort (18-28oC) for 77 – 97% of the year. Family expectations and experiences of comfort, and the various design strategies utilized were compared against the measured performance outcomes. This comparison revealed issues that limited quantification and implementation of design intent and highlighted factors that constrained system optimisation.

Place and displacement : southeast Queensland architecture

The "vernacular" housing tradition of southeast Queensland is easily identifiable. Its history is more complex. This study seeks to challenge two popular conceptions of the "Queenslander" history by showing that they actually provide contradictory explanations. The aim is to produce a more complex account of local architecture and its historical explanation so that both its past and its present practices can be better understood as a distinctly subtropical idiom. This discussion shows that such practices may respond to common concerns but that are also ever-changing.

Australian Learning and Teaching Council, Learning and Teaching Academic Standards Statement for Architecture

The development of the Learning and Teaching Academic Standards Statement for Architecture (the Statement) centred on requirements for the Master of Architecture and proceeded alongside similar developments in the building and construction discipline under the guidance and support of the Australian Deans of Built Environment and Design (ADBED). Through their representation of Australian architecture programs, ADBED have provided high-level leadership for the Learning and Teaching Academic Standards Project in Architecture (LTAS Architecture). The threshold learning outcomes (TLOs), the description of the nature and extent of the discipline, and accompanying notes were developed through wide consultation with the discipline and profession nationally. They have been considered and debated by ADBED on a number of occasions and have, in their fi nal form, been strongly endorsed by the Deans. ADBED formed the core of the Architecture Reference Group (chaired by an ADBED member) that drew together representatives of every peak organisation for the profession and discipline in Australia. The views of the architectural education community and profession have been provided both through individual submissions and the voices of a number of peak bodies. Over two hundred individuals from the practising profession, the academic workforce and the student cohort have worked together to build consensus about the capabilities expected of a graduate of an Australian Master of Architecture degree. It was critical from the outset that the Statement should embrace the wisdom of the greater ‘tribe’, should ensure that graduates of the Australian Master of Architecture were eligible for professional registration and, at the same time, should allow for scope and diversity in the shape of Australian architectural education. A consultation strategy adopted by the Discipline Scholar involved meetings and workshops in Perth, Melbourne, Sydney, Canberra and Brisbane. Stakeholders from all jurisdictions and most universities participated in the early phases of consultation through a series of workshops that concluded late in October 2010. The Draft Architecture Standards Statement was formed from these early meetings and consultation in respect of that document continued through early 2011. This publication represents the outcomes of work to establish an agreed standards statement for the Master of Architecture. Significant further work remains to ensure the alignment of professional accreditation and recognition procedures with emerging regulatory frameworks cascading from the establishment of the Tertiary Education Quality and Standards Agency (TEQSA). The Australian architecture community hopes that mechanisms can be found to integrate TEQSA’s quality assurance purpose with well-established and understood systems of professional accreditation to ensure the good standing of Australian architectural education into the future. The work to build renewed and integrated quality assurance processes and to foster the interests of this project will continue, for at least the next eighteen months, under the auspices of Australian Learning and Teaching Council (ALTC)-funded Architecture Discipline Network (ADN), led by ADBED and Queensland University of Technology. The Discipline Scholar gratefully acknowledges the generous contributions given by those in stakeholder communities to the formulation of the Statement. Professional and academic colleagues have travelled and gathered to shape the Standards Statement. Debate has been vigorous and spirited and the Statement is rich with the purpose, critical thinking and good judgement of the Australian architectural education community. The commitments made to the processes that have produced this Statement reflect a deep and abiding interest by the constituency in architectural education. This commitment bodes well for the vibrancy and productivity of the emergent Architecture Discipline Network (ADN). Endorsement, in writing, was received from the Australian Institute of Architects National Education Committee (AIA NEC): The National Education Committee (NEC) of the Australian Institute of Architects thank you for your work thus far in developing the Learning and Teaching Academic Standards for Architecture In particular, we acknowledge your close consultation with the NEC on the project along with a comprehensive cross-section of the professional and academic communities in architecture. The TLOs with the nuanced levels of capacities – to identify, develop, explain, demonstrate etc – are described at an appropriate level to be understood as minimum expectations for a Master of Architecture graduate. The Architects Accreditation Council of Australia (AACA) has noted: There is a clear correlation between the current processes for accreditation and what may be the procedures in the future following the current review. The requirement of the outcomes as outlined in the draft paper to demonstrate capability is an appropriate way of expressing the measure of whether the learning outcomes have been achieved. The measure of capability as described in the outcome statements is enhanced with explanatory descriptions in the accompanying notes.

Building envelope : performance optimisation processes for a daylight responsive architecture

Traditional shading design principles guide the vertical and horizontal orientation of fins, louvres and awnings being applied to orthogonal planar façades. Due to doubly curved envelopes characterising many contemporary designs, these rules of thumb are now not always applicable. Operable blinds attempt to regulate the fluctuating luminance of daylight and aid in shading direct sunlight. Mostly they remain closed, as workers are commonly too preoccupied to continually adjust them so a reliance on electrically powered lights remains a preference. To remedy these problems, the idea of what it is to sustainable enclose space is reconsidered through the geometric and kinetic optimisation of a parametric skin, with sunlight responsive modules that regulate interior light levels. This research concludes with an optimised design and also defines some unique metrics to gauge the design’s performance in terms of, the amount of exterior unobstructed view, its ability to shade direct sunlight and, its daylight glare probability.

Pore formation during dehydration of polycrystalline gypsum observed and quantified in a time-series synchrotron radiation based X-ray micro-tomography experiment

We conducted an in-situ X-ray micro-computed tomography heating experiment at the Advanced Photon Source (USA) to dehydrate an unconfined 2.3 mm diameter cylinder of Volterra Gypsum. We used a purpose-built X-ray transparent furnace to heat the sample to 388 K for a total of 310 min to acquire a three-dimensional time-series tomography dataset comprising nine time steps. The voxel size of 2.2 μm3 proved sufficient to pinpoint reaction initiation and the organization of drainage architecture in space and time. We observed that dehydration commences across a narrow front, which propagates from the margins to the centre of the sample in more than four hours. The advance of this front can be fitted with a square-root function, implying that the initiation of the reaction in the sample can be described as a diffusion process. Novel parallelized computer codes allow quantifying the geometry of the porosity and the drainage architecture from the very large tomographic datasets (20483 voxels) in unprecedented detail. We determined position, volume, shape and orientation of each resolvable pore and tracked these properties over the duration of the experiment. We found that the pore-size distribution follows a power law. Pores tend to be anisotropic but rarely crack-shaped and have a preferred orientation, likely controlled by a pre-existing fabric in the sample. With on-going dehydration, pores coalesce into a single interconnected pore cluster that is connected to the surface of the sample cylinder and provides an effective drainage pathway. Our observations can be summarized in a model in which gypsum is stabilized by thermal expansion stresses and locally increased pore fluid pressures until the dehydration front approaches to within about 100 μm. Then, the internal stresses are released and dehydration happens efficiently, resulting in new pore space. Pressure release, the production of pores and the advance of the front are coupled in a feedback loop.

Dichotomy in the design studio 2.0 : adapting to new blended learning environments

In a study aimed at better understanding how students adapt to new blended studio learning environments, all undergraduate and masters of architecture students at a large school of architecture in Australia, learned a semester of architectural design in newly renovated, technology embedded, design studio environments. The renovations addressed the lessons learned from a 2011 pilot study of a second year architectural design studio learned in a high technology embedded prototype digital laboratory. The new design studios were purpose designed for the architecture students and adapted Student-Centred Active Learning Environment for Undergraduate Programs design principles. At the end of the semester, the students completed a questionnaire about their experiences of learning in the new design studio environments. Using a dual method qualitative approach, the questionnaire data were coded and extrapolated using both thematic analysis and grounded theory methodology. The results from these two approaches were compared, contrasted and finally merged, to reveal five distinct emerging themes, which were instrumental in offering resistance or influencing adaptation to, the new blended studio learning environments. This paper reports on the study, discusses the major contributors to resistance and adaptation, and proposes points for consideration when renovating or designing new blended studio learning environments. This research extends the 2011 pilot study by the same authors: ‘Dichotomy in the design studio: Adapting to new blended learning environments’.

Dichotomy in the design studio : adapting to new blended learning environments

Since the architectural design studio learning environment was first established in the early 19th century at the École des Beaux-Arts in Paris, there has been a complete transformation in how the discipline of architecture is practiced and how students of architecture acquire information. Digital technologies allow students to access information instantly and learning is no longer confined to the rigid boundaries of a physical campus environment. In many schools of architecture in Australia, the physical design studio learning environments however, remain largely unchanged. Many learning environments could be mistaken for those last refurbished 30 years ago, being devoid of any significant technological intervention. While some teaching staff are eagerly embracing new digital technologies and attempting to modify their pedagogical approaches, the physical design studio learning environment is resistant to such efforts. In a study aimed at better understanding how staff and students adapt to new blended learning environments, a group of 165 second year architecture students at a large school of architecture in Australia were separated into two different design studio learning environments. 70% of students were allocated to a traditional design studio setting and 30% to a new, high technology embedded, prototype digital learning laboratory. The digital learning laboratory was purpose designed for the case-study users, adapted Student-Centred Active Learning Environment for Undergraduate Programs [SCALE-UP] principles, and built as part of a larger university research project. The architecture students attended the same lectures, followed the same studio curriculum and completed the same pieces of assessment; the only major differences were the teaching staff and physical environment within which the studios were conducted. At the end of the semester, all staff and students were asked to complete a questionnaire about their experiences and preferences within the two respective learning environments. The questionnaire response rate represented the opinions of 100% of the 10 teaching staff and over 70% of the students. Using a qualitative grounded theory approach, data were coded, extrapolated and compared, to reveal emerging key themes. The key themes formed the basis for in-depth interviews and focus groups of teaching staff and students, allowing the researchers to understand the data in more detail. The results of the data verified what had become increasingly evident during the course of the semester: an underlying negative resistance to the new digital studio learning environment, by both staff and students. Many participants openly exhibited a yearning for a return to the traditional design studio learning environments, particularly when the new technology caused frustration, by being unreliable or failing altogether. This paper reports on the study, discusses the negative resistance and explores the major contributors to resistance. The researchers are not aware of any similar previous studies across these particular settings and believe that it offers a necessary and important contribution to emergent research about adaptation to new digital learning environments.