Particle size distribution effects on preferential deposition areas in metal foam wrapped tube bundle

This paper presents a numerical model for understanding particle transport and deposition in metal foam heat exchangers. Two-dimensional steady and unsteady numerical simulations of a standard single row metal foam-wrapped tube bundle are performed for different particle size distributions, i.e. uniform and normal distributions. Effects of different particle sizes and fluid inlet velocities on the overall particle transport inside and outside the foam layer are also investigated. It was noted that the simplification made in the previously-published numerical works in the literature, e.g. uniform particle deposition in the foam, is not necessarily accurate at least for the cases considered here. The results highlight the preferential particle deposition areas both along the tube walls and inside the foam using a developed particle deposition likelihood matrix. This likelihood matrix is developed based on three criteria being particle local velocity, time spent in the foam, and volume fraction. It was noted that the particles tend to deposit near both front and rear stagnation points. The former is explained by the higher momentum and direct exposure of the particles to the foam while the latter only accommodate small particles which can be entrained in the recirculation region formed behind the foam-wrapped tubes.

Ausma Bushfire Research : Photographic record of built work

Colour Photographs of built work of architecture: Ausma House, Ocean Beach, Shire of Denmark Western Australia. Conducted as 100% commercial research with QUT-Client agreement. Clients M & S Ausma.

Autonomous hot metal carrier: Navigation and manipulation with a 20 tonne industrial vehicle

This paper reports work on the automation of a hot metal carrier, which is a 20 tonne forklift-type vehicle used to move molten metal in aluminium smelters. To achieve efficient vehicle operation, issues of autonomous navigation and materials handling must be addressed. We present our complete system and experiments demonstrating reliable operation. One of the most significant experiments was five-hours of continuous operation where the vehicle travelled over 8 km and conducted 60 load handling operations. Finally, an experiment where the vehicle and autonomous operation were supervised from the other side of the world via a satellite phone network are described.

Book Review: "Metal Rules the Globe: Heavy Metal Music around the World". Durham, NC: Duke University Press.

It is rare to find an anthology that realizes the possibilities of the form. We tend to regard our edited collections as lesser siblings, and forget their special value. But at times, a subject seems to require an edited collection much more than it does a classic monograph. So it is with the subject showcased here, which concerns the global circulation, performance and consumption of heavy metal. This is a relatively new and emerging body of work, hitherto scattered disparately in the broader popular music studies, but quickly gaining status as a “studies” with the establishment of a global conference, a journal, and publication of this anthology, all in recent years. Metal Rules the Globe took the editors’ a decade to compile. That they have thought deeply about how they want the collection to speak shows through in the book’s thoughtful arrangement and design, and in the way in which they draw on the contributions herein to develop for the field a research agenda that will take it forward...

Autonomous hot metal carrier

This paper reports work involved with the automation of a Hot Metal Carrier — a 20 tonne forklift-type vehicle used to move molten metal in aluminium smelters. To achieve efficient vehicle operation, issues of autonomous navigation and materials handling must be addressed. We present our complete system and experiments demontrating reliable operation. One of the most significant experiments was five-hours of continuous operation where the vehicle travelled over 8 km and conducted 60 load handling operations. We also describe an experiment where the vehicle and autonomous operation were supervised from the other side of the world via a satellite phone network.

Design studio terrains: Mapping the learning landscapes of Australian architectural education

It has been nearly 25 years since the problems associated with passive learning in large undergraduate classes were first established by McDermott (1991). STEM education, for example North Carolina State University’s SCALE-UP project, has subsequently been influenced by some unique aspects of design studio education. While there are now many institutions applying SCALE-UP or similar approaches to enable lively interaction, enhanced learning, increased student engagement, and to teach many different content areas to classes of all sizes, nearly all of these have remained in the STEM fields (Beichner, 2008). Architectural education, although originally at the forefront of this field, has arguably been left behind. Architectural practice is undergoing significant change, globally. Access to new technology and the development of specialised architectural documentation software has scaffolded new building procurement methods and allowed consultant teams to work more collaboratively, efficiently and even across different time zones. Up until recently, the spatial arrangements, pedagogical approaches, and project work outcomes in the architectural design studio, have not been dissimilar to its inception. It is not possible to keep operating architectural design studios the same way that they have for the past two hundred years, with this new injection of high-end technology and personal mobile Wi-Fi enabled devices. Employing a grounded theory methodology, this study reviews the current provision of architectural design learning terrains across a range of tertiary institutions, in Australia. Some suggestions are provided for how these spaces could be modified to address the changing nature of the profession, and implications for how these changes may impact the design of future SCALE-UP type spaces outside of the discipline of architecture, are also explored.

The sublime, affective process + architectural production

A year before Kate Nesbitt’s Theorising a New Agenda For Architecture (1996), the author penned a chapter on the significance of the sublime and its contribution to post-modern architecture via the uncanny or disturbing through the theories of Vidler and Eisenman (Nesbit, 1995). Twenty years on, we see its ongoing presence within the contemporary works of artists Kapoor, Ellison and Viola. Eisenmann and Libeskind aside, explicit reference to the Sublime whether through architectural praxis or theory appears to have been trumped by ecological derivatives and associated transactions, as catalyst for new architecture and architectural thinking. For Edmund Burke (1757), the Sublime was seen as a leading, an overpowering of self to a state of intense self-presence, often leading to a state of otherness. To experience the sublime is to experience affect, physiologically overwhelming the mental faculties through intensities of astonishment, terror, obscurity, magnificence, and reverence. Key here is Burke’s articulation of the stages of the sublime encounter, particularly so, its implications for the process of production which architectural theorists appear to have overstepped in their valorisation of the sublime object. This paper seeks to resituate the sublime within the context of architectural production. Through concepts such as material thinking, bodies and making strange, the paper explores a shift in focus toward affective processes traced from Burke’s inquiry. Rather than proposing strategies solely for affect within the work itself, the focus lies upon the designing experience, where blockage and desirous forces are critical partners in the process of production, as revealed through recent studio programs entitled Strange Space.

Superhydrophobic fabrics for oil-water separation based on the metal organic charge transfer complex CuTCNAQ

This work reports on the fabrication of a superhydrophobic nylon textile based on the organic charge transfer complex CuTCNAQ (TCNAQ = 11,11,12,12-tetracyanoanthraquinodimethane). The nylon fabric that is metallized with copper undergoes a spontaneous chemical reaction with TCNAQ dissolved in acetonitrile to form nanorods of CuTCNAQ that are intertwined over the entire surface of the fabric. This creates the necessary micro and nanoscale roughness that is required for the Cassie-Baxter state thereby achieving a superhydrophobic/superoleophilic surface without the need for a fluorinated surface. The material is characterised with SEM, FT-IR and XPS spectroscopy and investigated for its ability to separate oil and water in two modes, namely under gravity and as an absorbent. It is found that the fabric can separate dichloromethane, olive oil and crude oil from water and in fact reduce the water content of the oil during the separation process. The fabric is reusable and tolerant to conditions such as seawater, hydrochloric acid and extensive time periods on the shelf. Given that CuTCNAQ is a copper based semiconductor may also open up the possibility of other applications in areas such as photocatalysis and antibacterial applications.

3D hierarchical rutile TiO2 and metal-free organic sensitizer producing dye-sensitized solar cells 8.6% conversion efficiency

Three-dimensional (3D) hierarchical nanoscale architectures comprised of building blocks, with specifically engineered morphologies, are expected to play important roles in the fabrication of 'next generation' microelectronic and optoelectronic devices due to their high surface-to-volume ratio as well as opto-electronic properties. Herein, a series of well-defined 3D hierarchical rutile TiO2 architectures (HRT) were successfully prepared using a facile hydrothermal method without any surfactant or template, simply by changing the concentration of hydrochloric acid used in the synthesis. The production of these materials provides, to the best of our knowledge, the first identified example of a ledgewise growth mechanism in a rutile TiO2 structure. Also for the first time, a Dye-sensitized Solar Cell (DSC) combining a HRT is reported in conjunction with a high-extinction-coefficient metal-free organic sensitizer (D149), achieving a conversion efficiency of 5.5%, which is superior to ones employing P25 (4.5%), comparable to state-of-the-art commercial transparent titania anatase paste (5.8%). Further to this, an overall conversion efficiency 8.6% was achieved when HRT was used as the light scattering layer, a considerable improvement over the commercial transparent/reflector titania anatase paste (7.6%), a significantly smaller gap in performance than has been seen previously.

Corporate America And The New Luminous Environment: Kelly’s work with Johnson, Mies, and Noyes

[book] The potential of electric light as a new building “material” was recognized in the 1920s and became a useful design tool by the mid-century. Skillful lighting allowed for theatricality, narrative, and a new emphasis on structure and space. The Structure of Light tells the story of the career of Richard Kelly, the field’s most influential figure. Six historians, architects, and practitioners explore Kelly’s unparalleled influence on modern architecture and his lighting designs for some of the 20th century’s most iconic buildings: Philip Johnson’s Glass House; Louis Kahn’s Kimbell Art Museum; Eero Saarinen’s GM Technical Center; and Mies van der Rohe’s Seagram Building, among many others. This beautifully illustrated history demonstrates the range of applications, building types, and artistic solutions he employed to achieve a “nocturnal modernity” that would render buildings evocatively different at night. The survival of Kelly’s rich correspondence and extensive diaries allows an in-depth look at the triumphs and uncertainties of a young profession in the making. The first book to focus on the contributions of a master in the field of architectural lighting, this fascinating volume celebrates the practice’s significance in modern design.

Liberty relighting, 20 years later

Recognized around the world as a powerful beacon for freedom, hope, and opportunity, the Statue of Liberty's light is not just metaphorical: her dramatic illumination is a perfect example of American ingenuity and engineering. Since the statue's installation in New York Harbor in 1886, lighting engineers and designers had struggled to illuminate the 150-foot copper-clad monument in a manner becoming an American icon. It took the thoughtful and creative approach of Howard Brandston-a legend in his own right-to solve this lighting challenge. In 1984, the designer was asked to give the statue a much-needed lighting makeover in preparation for its centennial. In order to avoid the shortcomings of previous attempts, he studied the monument from every angle and in all lighting conditions, discovering that it looked best in the light of dawn. Brandston determined that he would need 'one lamp to mimic the morning sun and one lamp to mimic the morning sky.' Learning that no existing lamps could simulate these conditions, Brandston partnered with General Electric to develop two new metal halide products. With only a short time for R&D, a team of engineers at GE's Nela Park laboratories assembled a 'top secret' testing room dedicated to the Statue of Liberty project. After nearly two years of work to perfect the new lamps, the 'dawn's early light' effect was finally achieved just days before the centennial celebrations were to take place in 1986. 'It was truly a labor of love,' he recalls.

The InstaBooth: Making common ground for media architectural design

Media architecture has emerged from and relies upon a range of different disciplinary traditions and areas of expertise. As this field develops, it is timely to reflect upon the ways in which designers of different disciplinary stripes can be brought together to collaborate in a design process. What are the means by which design teams can establish a ‘common ground’ where design work can take place while recognizing the diversity of ways of working those different disciplines bring to the process? A co-design approach has been the fundamental backbone of the InstaBooth project, which has brought together a multidisciplinary design team of academics and practitioners. The intention of this project has been to explore the combination of digital and physical interactions within a small media architecture installation to intervene with urban environments and public places for the purposes of community engagement. It is by exploring the design process of the InstaBooth project that we highlight the value of multi-disciplinary collaborations, the lessons that can be learned, and the struggles and hurdles along the way. This paper highlights the iterative process of design, the materials and physical prototypes that were employed to ultimately create a working version of the InstaBooth, a media architecture that evolves as users push its boundaries and take ownership of the installation. The concept of the InstaBooth continues to develop not only as more data are collected on its mechanics and potentials through observations, interviews and workshops, but also as more and more users engage with the installation in their individual ways.