Use of electronic portal imaging devices for electron treatment verification

This study aims to help broaden the use of electronic portal imaging devices (EPIDs) for pre-treatment patient positioning verification, from photon-beam radiotherapy to photon- and electron-beam radiotherapy, by proposing and testing a method for acquiring clinicallyuseful EPID images of patient anatomy using electron beams, with a view to enabling and encouraging further research in this area. EPID images used in this study were acquired using all available beams from a linac configured to deliver electron beams with nominal energies of 6, 9, 12, 16 and 20 MeV, as well as photon beams with nominal energies of 6 and 10 MV. A widely-available heterogeneous, approximately-humanoid, thorax phantom was used, to provide an indication of the contrast and noise produced when imaging different types of tissue with comparatively realistic thicknesses. The acquired images were automatically calibrated, corrected for the effects of variations in the sensitivity of individual photodiodes, using a flood field image. For electron beam imaging, flood field EPID calibration images were acquired with and without the placement of blocks of water-equivalent plastic (with thicknesses approximately equal to the practical range of electrons in the plastic) placed upstream of the EPID, to filter out the primary electron beam, leaving only the bremsstrahlung photon signal. While the electron beam images acquired using a standard (unfiltered) flood field calibration were observed to be noisy and difficult to interpret, the electron beam images acquired using the filtered flood field calibration showed tissues and bony anatomy with levels of contrast and noise that were similar to the contrast and noise levels seen in the clinically acceptable photon beam EPID images. The best electron beam imaging results (highest contrast, signal-to-noise and contrast-to-noise ratios) were achieved when the images were acquired using the higher energy electron beams (16 and 20 MeV) when the EPID was calibrated using an intermediate (12 MeV) electron beam energy. These results demonstrate the feasibility of acquiring clinically-useful EPID images of patient anatomy using electron beams and suggest important avenues for future investigation, thus enabling and encouraging further research in this area. There is manifest potential for the EPID imaging method proposed in this work to lead to the clinical use of electron beam imaging for geometric verification of electron treatments in the future.

Design thinking using a collaborative model for skin cancer prevention

Physical activity is well recognised as a means to reduce cancer risk; however, outdoor activity can increase sun exposure and consequential skin cancer risk. It is proposed, one of the key potential solutions to promote active lifestyles whilst enhancing protection against skin cancer is design resolution for active apparel that considers Australia’s sub-tropical climate whilst maintaining comfort, aesthetic appeal and performance. Using a design thinking approach, facilitated through collaboration between an NGO and a university, student designers were tasked with developing apparel prototypes to explore this challenge. Through practical ideation of problems, potential design solutions were developed within a modest NGO budget and adherence to specific brand guidelines. This project is novel as it demonstrates a low cost yet effective way of collaboratively creating a product to meet multiple needs, rather than reactively assessing already manufactured sun protection products for endorsement. It is a nimble and unique stepping stone in integrating sun safety considerations into clothing that is appealing to the population and creating cross-industry understandings of how design can better contribute to human health and wellbeing. Outcomes to be shared include empirical insights for updating sun safe clothing guidelines, issues around the aesthetic nature of sun safe apparel, and the role of design education for sun safety.

DFT study of electronic and optical properties of anatase titanium dioxide tuned by nitrogen and lithium co-doping

The electronic and optical properties of anatase titanium dioxide (TiO2), co-doped by nitrogen (N) and lithium (Li), have been investigated by density functional theory plus Hubbard correction term U, namely DFT+U. It is found that Li-dopants can effectively balance the net charges brought by N-dopants and shift the local state to the top of valence band. Depending on the distribution of dopants, the adsorption edges of TiO2 may be red- or blue-shifted, being consistent with recent experimental observations.

Plasma polymerised thin films for flexible electronic applications

The significant advancement and growth of organic and flexible electronic applications demand materials with enhanced properties. This paper reports the fabrication of a nonsynthetic polymer thin film using radio frequency plasma polymerisation of 3,7-dimethyl-1,6-octadien-3-ol. The fabricated optically transparent thin film exhibited refractive index of approximately 1.55 at 500 nm and rate of deposition was estimated to be 40 nm/min. The surface morphology and chemical properties of the thin films were also reported in this paper. The optical band gap of the material is around 2.8 eV. The force of adhesion and Young's modulus of the linalool polymer thin films were measured using force-displacement curves obtained from a scanning probe microscope. The friction coefficient of linalool polymer thin films was measured using the nanoscratch test. The calculated Young's modulus increased linearly with increase in input power while the friction coefficient decreased.

Plasma assisted surface modification of organic biopolymers to prevent bacterial attachment

Despite many synthetic biomaterials having physical properties that are comparable or even superior to those of natural body tissues, they frequently fail due to the adverse physiological reactions they cause within the human body, such as infection and inflammation. The surface modification of biomaterials is an economical and effective method by which biocompatibility and biofunctionality can be achieved while preserving the favorable bulk characteristics of the biomaterial, such as strength and inertness. Amongst the numerous surface modification techniques available, plasma surface modification affords device manufacturers a flexible and environmentally friendly process that enables tailoring of the surface morphology, structure, composition, and properties of the material to a specific need. There are a vast range of possible applications of plasma modification in biomaterial applications, however, the focus of this review paper is on processes that can be used to develop surface morphologies and chemical structures for the prevention of adhesion and proliferation of pathogenic bacteria on the surfaces of in-dwelling medical devices. As such, the fundamental principles of bacterial cell attachment and biofilm formation are also discussed. Functional organic plasma polymerised coatings are also discussed for their potential as biosensitive interfaces, connecting inorganic/metallic electronic devices with their physiological environments.

Fabrication of Electronic Materials from Australian Essential Oils

This RIRDC publication reports the findings and recommendations of the RIRDC funded study, "Fabrication of Electronic Materials from Australian Essential Oils". This project was undertaken to facilitate an expansion of the Australian Essential Oils Industry through the development of novel applications in the Electronic and Bio-Materials Industries. The findings presented in this report will provide value broadly across the Australian Essential Oils Industry, and more particularly to the growers involved in the production of tea tree, lavender and other essential oils. Several essential oils, namely tea tree oil, sandalwood oil, eucalyptus oil, alpha-pinene, d-limonene, lavender oil (a separate PhD project) and five major components of tea tree oil were tested. With the exception of sandalwood oil, all oils investigated were successfully polymerised. Importantly, this project determined that it is possible to use an environmentally friendly, inexpensive process of polymerisation to fabricate materials from essential oils in a reproducible manner with properties required by the optics, electronics, protective coatings, and bio-material industries.

Fabrication and characterization of RF plasma polymerized thin films from 3,7-dimethyl-1,6-octadien-3-ol for electronic and biomaterial applications

Poly(linalool) thin films were fabricated using RF plasma polymerisation. All films were found to be smooth, defect-free surfaces with average roughness of 0.44 nm. The FTIR analysis of the polymer showed a notable reduction in –OH moiety and complete dissociation of C=C unsaturation compared to the monomer, and presence of a ketone band absent from the spectrum of the monomer. Poly(linalool) were characterised by chain branching and a large quantity of short polymer chains. Films were optically transparent, with refractive index and extinction coefficient of 1.55 and 0.001 (at 500 nm) respectively, indicating a potential application as an encapsulating (protective) coating for circuit boards. The optical band gap was calculated to be 2.82 eV, which is in the semiconducting energy gap region.

Analysis and prevention of extreme vibration in high speed craft - A research framework

Extreme vibration has been reported for small, high speed craft in the maritime sector, with performance and health threatening effects on boat operators and crew. Musculoskeletal injuries are an enduring problem for high speed craft passengers. Spinal or joint injuries and neurological disorders may occur from repetitive pounding over rough water, continued vibration and single impact events. The risk from whole body vibration (WBV) induced through the small vessels mainly depends on time spent on the craft, which can’t be changed in a military scenario; as well as the number of shocks and jolts, and their magnitude and frequency. In the European Union for example, physical agents directives require all employers to control exposure to a number of physical agents including noise and vibration. The EC Vibration Directive 2002/44/EC then sets out regulations for the control of health and safety risks from the exposure of workers to hand arm vibration (HAV) and WBV in the workplace. Australia has exposure standards relating to WBV, AS 2670.1-2001 – Evaluation of human exposure to whole body vibration. This standard is identical to the ISO 2631-1:1997, Mechanical vibration and shock – Evaluation of human exposure to whole-body vibration. Currently, none of the jurisdictions in Australia have specific regulations for vibration exposures in workplaces. However vibration is mentioned to varying degrees in their general regulations, codes of practice and guidance material. WBV on high speed craft is normally caused by “continuous 'hammering' from short steep seas or wind against tide conditions. Shock on High Speed Craft is usually caused by random impacts. Military organisations need the knowledge to make informed decisions regarding their marine operations, compliance with legislation and potentially harmful health effects, and develop and implement appropriate counter-measures. Marine case studies in the UK such as published MAIB (Marine Accident Investigation Branch) reports show injuries that have occurred in operation, and subsequent MCA (Maritime Coastguard Agency) guidance is provided (MGN 436 (M+F), WHOLE-BODY VIBRATION: Guidance on Mitigating Against the Effects of Shocks and Impacts on Small Vessels. MCA, 2011). This paper proposes a research framework to study the origin, impact and pathways for prevention of WBV in small, high speed craft in a maritime environment.

Educators’ perspectives about how older hospital patients can engage in a falls prevention education programme: A qualitative process evaluation

- Objectives Falls are the most frequent adverse event reported in hospitals. Patient and staff education delivered by trained educators significantly reduced falls and injurious falls in an older rehabilitation population. The purpose of the study was to explore the educators’ perspectives of delivering the education and to conceptualise how the programme worked to prevent falls among older patients who received the education. - Design A qualitative exploratory study. - Methods Data were gathered from three sources: conducting a focus group and an interview (n=10 educators), written educator notes and reflective researcher field notes based on interactions with the educators during the primary study. The educators delivered the programme on eight rehabilitation wards for periods of between 10 and 40 weeks. They provided older patients with individualised education to engage in falls prevention and provided staff with education to support patient actions. Data were thematically analysed and presented using a conceptual framework. - Results Falls prevention education led to mutual understanding between staff and patients which assisted patients to engage in falls prevention behaviours. Mutual understanding was derived from the following observations: the educators perceived that they could facilitate an effective three-way interaction between staff actions, patient actions and the ward environment which led to behaviour change on the wards. This included engaging with staff and patients, and assisting them to reconcile differing perspectives about falls prevention behaviours. - Conclusions Individualised falls prevention education effectively provides patients who receive it with the capability and motivation to develop and undertake behavioural strategies that reduce their falls, if supported by staff and the ward environment.

Design challenges for electronic medication administration record systems in residential aged care facilities: A formative evaluation

Introduction Electronic medication administration record (eMAR) systems are promoted as a potential intervention to enhance medication safety in residential aged care facilities (RACFs). The purpose of this study was to conduct an in-practice evaluation of an eMAR being piloted in one Australian RACF before its roll out, and to provide recommendations for system improvements. Methods A multidisciplinary team conducted direct observations of workflow (n=34 hours) in the RACF site and the community pharmacy. Semi-structured interviews (n=5) with RACF staff and the community pharmacist were conducted to investigate their views of the eMAR system. Data were analysed using a grounded theory approach to identify challenges associated with the design of the eMAR system. Results The current eMAR system does not offer an end-to-end solution for medication management. Many steps, including prescribing by doctors and communication with the community pharmacist, are still performed manually using paper charts and fax machines. Five major challenges associated with the design of eMAR system were identified: limited interactivity; inadequate flexibility; problems related to information layout and semantics; the lack of relevant decision support; and system maintenance issues.We suggest recommendations to improve the design of the eMAR system and to optimize existing workflows. Discussion Immediate value can be achieved by improving the system interactivity, reducing inconsistencies in data entry design and offering dedicated organisational support to minimise connectivity issues. Longer-term benefits can be achieved by adding decision support features and establishing system interoperability requirements with stakeholder groups (e.g. community pharmacies) prior to system roll out. In-practice evaluations of technologies like eMAR system have great value in identifying design weaknesses which inhibit optimal system use.

Who does nutrition prevention work in Queensland? An investigation of structural and political workforce reforms

- Aim This study aimed (i) to determine the change in the number of government-funded nutrition positions following structural and political reforms and (ii) to describe the remaining workforce available to do nutrition prevention work, including student placements, in Queensland. - Methods Positions funded by the Queensland government were counted using departmental human resource data and compared with data collected 4 years earlier. Positions not funded by the government were identified using formal professional networks and governance group lists. Both groups were sent an online survey that explored their position name, funding source, employer, qualifications, years of experience, work in prevention and ability to supervise students. - Results There was a 90% reduction in the number of nutrition prevention positions funded by the government between 2009 (137 full time equivalents (FTE)) and 2013 (14 FTE). In 2013, 313 specialist (n = 92) and generalist (n = 221) practitioners were identified as potentially working in nutrition prevention throughout Queensland. A total of 30 permanent FTEs indicated over 75% of their work focused on prevention. This included the 14 FTE funded by the Queensland government and an additional 16 FTE from other sectors. Generalists did not consider themselves part of the nutrition workforce. - Conclusions Queensland experienced an extreme reduction in its nutrition prevention workforce as a result of political and structural reforms. This disinvestment by the Queensland government was not compensated for by other sectors, and has left marked deficits in public health nutrition capacity, including student placements.

The authentication of electronic evidence

This thesis examines whether the rules for of evidence, which were developed around paper over centuries, are adequate for the authentication of electronic evidence. The history of documentary evidence is examined, and the nature of electronic evidence is explored, particularly recent types of electronic evidence such as social media and 'the Cloud'. The old rules are then critically applied to the varied types of electronic evidence to determine whether or not these old rules are indeed adequate.

Electronic Building Passport - Final Report: Project 2 National Energy Efficient Building Project Phase 2

The National Energy Efficient Building Project (NEEBP) Phase One report, published in December 2014, investigated “process issues and systemic failures” in the administration of the energy performance requirements in the National Construction Code. It found that most stakeholders believed that under-compliance with these requirements is widespread across Australia, with similar issues being reported in all states and territories. The report found that many different factors were contributing to this outcome and, as a result, many recommendations were offered that together would be expected to remedy the systemic issues reported. To follow up on this Phase 1 report, three additional projects were commissioned as part of Phase 2 of the overall NEEBP project. This Report deals with the development and piloting of an Electronic Building Passport (EBP) tool – a project undertaken jointly by pitt&sherry and a team at the Queensland University of Technology (QUT) led by Dr Wendy Miller. The other Phase 2 projects cover audits of Class 1 buildings and issues relating to building alterations and additions. The passport concept aims to provide all stakeholders with (controlled) access to the key documentation and information that they need to verify the energy performance of buildings. This trial project deals with residential buildings but in principle could apply to any building type. Nine councils were recruited to help develop and test a pilot electronic building passport tool. The participation of these councils – across all states – enabled an assessment of the extent to which these councils are currently utilising documentation; to track the compliance of residential buildings with the energy performance requirements in the National Construction Code (NCC). Overall we found that none of the participating councils are currently compiling all of the energy performance-related documentation that would demonstrate code compliance. The key reasons for this include: a major lack of clarity on precisely what documentation should be collected; cost and budget pressures; low public/stakeholder demand for the documentation; and a pragmatic judgement that non-compliance with any regulated documentation requirements represents a relatively low risk for them. Some councils reported producing documentation, such as certificates of final completion, only on demand, for example. Only three of the nine council participants reported regularly conducting compliance assessments or audits utilising this documentation and/or inspections. Overall we formed the view that documentation and information tracking processes operating within the building standards and compliance system are not working to assure compliance with the Code’s energy performance requirements. In other words the Code, and its implementation under state and territory regulatory processes, is falling short as a ‘quality assurance’ system for consumers. As a result it is likely that the new housing stock is under-performing relative to policy expectations, consuming unnecessary amounts of energy, imposing unnecessarily high energy bills on occupants, and generating unnecessary greenhouse gas emissions. At the same time, Councils noted that the demand for documentation relating to building energy performance was low. All the participant councils in the EBP pilot agreed that documentation and information processes need to work more effectively if the potential regulatory and market drivers towards energy efficient homes are to be harnessed. These findings are fully consistent with the Phase 1 NEEBP report. It was also agreed that an EBP system could potentially play an important role in improving documentation and information processes. However, only one of the participant councils indicated that they might adopt such a system on a voluntary basis. The majority felt that such a system would only be taken up if it were: - A nationally agreed system, imposed as a mandatory requirement under state or national regulation; - Capable of being used by multiple parties including councils, private certifiers, building regulators, builders and energy assessors in particular; and - Fully integrated into their existing document management systems, or at least seamlessly compatible rather than a separate, unlinked tool. Further, we note that the value of an EBP in capturing statistical information relating to the energy performance of buildings would be much greater if an EBP were adopted on a nationally consistent basis. Councils were clear that a key impediment to the take up of an EBP system is that they are facing very considerable budget and staffing challenges. They report that they are often unable to meet all community demands from the resources available to them. Therefore they are unlikely to provide resources to support the roll out of an EBP system on a voluntary basis. Overall, we conclude from this pilot that the public good would be well served if the Australian, state and territory governments continued to develop and implement an Electronic Building Passport system in a cost-efficient and effective manner. This development should occur with detailed input from building regulators, the Australian Building Codes Board (ABCB), councils and private certifiers in the first instance. This report provides a suite of recommendations (Section 7.2) designed to advance the development and guide the implementation of a national EBP system.

Prevention of foot ulcers in the at-risk patient with diabetes: A systematic review

Background Prevention of foot ulcers in patients with diabetes is extremely important to help reduce the enormous burden of foot ulceration on both patient and health resources. A comprehensive analysis of reported interventions is not currently available, but is needed to better inform caregivers about effective prevention. The aim of this systematic review is to investigate the effectiveness of interventions to prevent first and recurrent foot ulcers in persons with diabetes who are at risk for ulceration. Methods The available medical scientific literature in PubMed, EMBASE, CINAHL and the Cochrane database was searched for original research studies on preventative interventions. Both controlled and non-controlled studies were selected. Data from controlled studies were assessed for methodological quality by two independent reviewers. Results From the identified records, a total of 30 controlled studies (of which 19 RCTs) and another 44 non-controlled studies were assessed and described. Few controlled studies, of generally low to moderate quality, were identified on the prevention of a first foot ulcer. For the prevention of recurrent plantar foot ulcers, multiple RCTs with low risk of bias show the benefit for the use of daily foot skin temperature measurements and consequent preventative actions, as well as for therapeutic footwear that demonstrates to relieve plantar pressure and that is worn by the patient. To prevent recurrence, some evidence exists for integrated foot care when it includes a combination of professional foot treatment, therapeutic footwear and patient education; for just a single session of patient education, no evidence exists. Surgical interventions can be effective in selected patients, but the evidence base is small. Conclusion The evidence base to support the use of specific self-management and footwear interventions for the prevention of recurrent plantar foot ulcers is quite strong, but is small for the use of other, sometimes widely applied, interventions and is practically nonexistent for the prevention of a first foot ulcer and non-plantar foot ulcer.

The effect of flexor tenotomy on healing and prevention of neuropathic diabetic foot ulcers on the distal end of the toe

Background Flexor tenotomy is a minimally invasive surgical alternative for the treatment of neuropathic diabetic foot ulcers on the distal end of the toe. The influence of infection on healing and time to heal after flexor tenotomy is unknown. Flexor tenotomy can also be used as a prophylactic treatment. The effectiveness as a prophylactic treatment has not been described before. Methods A retrospective study was performed with the inclusion of all consecutive flexor tenotomies from one hospital between January 2005 and December 2011. Results From 38 ulcers, 35 healed (92%), with a mean time to heal of 22 ± 26 days. The longest duration for healing was found for infected ulcers that were penetrating to bone (35 days; p = .042). Cases of prophylactic flexor tenotomies (n=9) did not result in any ulcer or other complications during follow-up. Conclusions The results of this study suggest that flexor tenotomy may be beneficial for neuropathic diabetic foot ulcers on the distal end of the toe, with a high healing percentage and a short mean time to heal. Infected ulcers that penetrated to bone took a significantly longer time to heal. Prospective research, to confirm the results of this retrospective study, should be performed.