Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

Common variants in the CYP2C19 gene are associated with susceptibility to endometriosis

Objective: To follow-up previous studies highlighting a possible role for cytochrome P450, family 2, subfamily C, 19 (CYP2C19) in susceptibility to endometriosis by searching for additional variants in the CYP2C19 gene that may be associated with the disease. Design Case-control study. Setting Academic research. Subject(s) The cases comprised 2,271 women with surgically confirmed endometriosis; the controls comprised 939 women with self-report of no endometriosis and 1,770 unscreened population samples. Intervention(s) Sequencing of the CYP2C19 region and follow-up of 80 single nucleotide polymorphisms (SNPs) in two case-control samples. Main Outcome Measure(s) Allele frequency differences between cases and controls. Result(s) Sequencing of the CYP2C19 gene region resulted in the detection of a large number of known and novel SNPs. Genotyping of 80 polymorphic SNPs in 901 endometriosis cases and 939 controls resulted in study-wide significant association signals for SNPs in moderate or complete linkage disequilibrium with rs4244285, a functional SNP in exon 5 that abrogates CYP2C19 function through the creation of an alternative splice site. Evidence of association was also detected for another functional SNP in the CYP2C19 promoter, rs12248560, which was highlighted in our previous study. Conclusion(s) Functional variants in CYP2C19 may contribute to endometriosis susceptibility in both familial and sporadic cases. © 2014 by American Society for Reproductive Medicine.

A systematic review of interventions to enhance medication adherence in children and adolescents with chronic illness

Introduction Poor medication adherence is common in children and adolescents with chronic illness, but there is uncertainty about the best way to enhance medication adherence in this group. The authors conducted a systematic review of controlled trials examining interventions that aim to improve medication adherence. Method A comprehensive literature search was undertaken to locate controlled trials that described specific interventions aiming to improve adherence to long-term medication, where participants were aged 18 years and under, medication adherence was reported as an outcome measure, and which could be implemented by individual health practitioners. Studies were reviewed for quality and outcome. Results 17 studies met inclusion criteria: seven studies examined educational strategies, seven studies examined behavioural interventions and three studies examined educational intervention combined with other forms of psychological therapies. Only two of seven studies reported a clear benefit for education on medication adherence, whereas four of seven trials indicated a benefit of behavioural approaches on medication adherence. One trial reported that combining education with behavioural management may be more effective than education alone. Studies which combined education with other non-medication specific psychological interventions failed to demonstrate a beneficial effect on medication adherence. Only two studies examined adherence-promoting interventions in young people with established adherence problems. Conclusion These findings suggest that education interventions alone are insufficient to promote adherence in children and adolescents, and that incorporating a behavioural component to adherence interventions may increase potential efficacy. Future research should examine interventions in high-risk groups.

Volatile organic compounds: Characteristics, distribution and sources in urban schools

Long term exposure to organic pollutants, both inside and outside school buildings may affect children’s health and influence their learning performance. Since children spend significant amount of time in school, air quality, especially in classrooms plays a key role in determining the health risks associated with exposure at schools. Within this context, the present study investigated the ambient concentrations of Volatile Organic Compounds (VOCs) in 25 primary schools in Brisbane with the aim to quantify the indoor and outdoor VOCs concentrations, identify VOCs sources and their contribution, and based on these; propose mitigation measures to reduce VOCs exposure in schools. One of the most important findings is the occurrence of indoor sources, indicated by the I/O ratio >1 in 19 schools. Principal Component Analysis with Varimax rotation was used to identify common sources of VOCs and source contribution was calculated using an Absolute Principal Component Scores technique. The result showed that outdoor 47% of VOCs were contributed by petrol vehicle exhaust but the overall cleaning products had the highest contribution of 41% indoors followed by air fresheners and art and craft activities. These findings point to the need for a range of basic precautions during the selection, use and storage of cleaning products and materials to reduce the risk from these sources.

Inability to swallow tablets is common and cause for concern

We naturally chew food before swallowing, but tablets and capsules require a complicated, conscious mechanism to over-ride the need to chew and the gag reflex, designed to eject foodstuffs that are not adequately chewed...

Gamifying collective intelligence for the common good

The rise of the mobile internet enables the creation of applications that provide new and easier ways for people to organise themselves, raise issues, take action and interact with their city. At the same time, society faces new problems that can only be solved when citizens work together. Nevertheless, a lack of motivation or knowledge often prevents many citizens from regularly contributing to the common good. In this position paper, we present DoGood – a mobile app – as a socio-technological system that aims at supporting the collective intelligence of citizens in their pursuit of civic engagement and civic collaboratories. Our study asks to what extent gamification can motivate users to “do good” deeds. The DoGood app uses gamified elements to encourage citizens to submit and promote their civic activities as well as to join the activities of others. Gamification is sometimes criticised for simply adding a limited number of game elements, such as leaderboards, on top of an existing experience with the hope of increasing motivation. However, in the case of the DoGood app, the process of game design was an integral part of the development, and the gamified elements target the user’s intrinsic motivations instead of providing them with an external reward. In this paper, we present design elements of the app and discuss their potential to support collective intelligence for the common good.

Common psychotic symptoms can be explained by the theory of ecological perception

The symptoms of psychiatric illness are diverse, as are the causes of the illnesses that cause them. Yet, regardless of the heterogeneity of cause and presentation, a great deal of symptoms can be explained by the failure of a single perceptual function – the reprocessing of ecological perception. It is a central tenet of the ecological theory of perception that we perceive opportunities to act. It has also been found that perception automatically causes actions and thoughts to occur unless this primary action pathway is inhibited. Inhibition allows perceptions to be reprocessed into more appropriate alternative actions and thoughts. Reprocessing of this kind takes place over the entire frontal lobe and it renders action optional. Choice about what action to take (if any) is the basis for the feeling of autonomy and ultimately for the sense-of-self. When thoughts and actions occur automatically (without choice) they appear to originate outside of the self, thereby providing prima facie evidence for some of the bizarre delusions that define schizophrenia such as delusional misidentification, delusions of control and Cotard’s delusion. Automatic actions and thoughts are triggered by residual stimulation whenever reprocessing is insufficient to balance automatic excitatory cues (for whatever reason). These may not be noticed if they are neutral and therefore unimportant whereas actions and thoughts with a positive bias are desirable. Responses to negative stimulus, on the other hand, are always unwelcome, because the actions that are triggered will carry the negative bias. Automatic thoughts may include spontaneous positive feelings of love and joy, but automatic negative thoughts and visualisations are experienced as hallucinations. Not only do these feel like they emerge from elsewhere but they carry a negative bias (they are most commonly critical, rude and are irrationally paranoid). Automatic positive actions may include laughter and smiling and these are welcome. Automatic behaviours that carry a negative bias, however, are unwelcome and like hallucinations, occur without a sense of choice. These include crying, stereotypies, perseveration, ataxia, utilization and imitation behaviours and catatonia.

Stochastic analysis of a radial-inflow turbine in the presence of parametric uncertainties

This paper presents an uncertainty quantification study of the performance analysis of the high pressure ratio single stage radial-inflow turbine used in the Sundstrand Power Systems T-100 Multi-purpose Small Power Unit. A deterministic 3D volume-averaged Computational Fluid Dynamics (CFD) solver is coupled with a non-statistical generalized Polynomial Chaos (gPC) representation based on a pseudo-spectral projection method. One of the advantages of this approach is that it does not require any modification of the CFD code for the propagation of random disturbances in the aerodynamic and geometric fields. The stochastic results highlight the importance of the blade thickness and trailing edge tip radius on the total-to-static efficiency of the turbine compared to the angular velocity and trailing edge tip length. From a theoretical point of view, the use of the gPC representation on an arbitrary grid also allows the investigation of the sensitivity of the blade thickness profiles on the turbine efficiency. The gPC approach is also applied to coupled random parameters. The results show that the most influential coupled random variables are trailing edge tip radius coupled with the angular velocity.

Common Alzheimer's disease risk variant within the CLU gene affects white matter microstructure in young adults

There is a strong genetic risk for late-onset Alzheimer's disease (AD), but so far few gene variants have been identified that reliably contribute to that risk. A newly confirmed genetic risk allele C of the clusterin (CLU) gene variant rs11136000 is carried by ~88% of Caucasians. The C allele confers a 1.16 greater odds of developing late-onset AD than the T allele. AD patients have reductions in regional white matter integrity. We evaluated whether the CLU risk variant was similarly associated with lower white matter integrity in healthy young humans. Evidence of early brain differences would offer a target for intervention decades before symptom onset. We scanned 398 healthy young adults (mean age, 23.6 ± 2.2 years) with diffusion tensor imaging, a variation of magnetic resonance imaging sensitive to white matter integrity in the living brain. We assessed genetic associations using mixed-model regression at each point in the brain to map the profile of these associations with white matter integrity. Each C allele copy of the CLUvariant was associated with lower fractional anisotropy-a widely accepted measure of white matter integrity-in multiple brain regions, including several known to degenerate in AD. These regions included the splenium of the corpus callosum, the fornix, cingulum, and superior and inferior longitudinal fasciculi in both brain hemispheres. Young healthy carriers of the CLU gene risk variant showed a distinct profile of lower white matter integrity that may increase vulnerability to developing AD later in life.

Common genetic variants influence human subcortical brain structures

The highly complex structure of the human brain is strongly shaped by genetic influences. Subcortical brain regions form circuits with cortical areas to coordinate movement, learning, memory and motivation, and altered circuits can lead to abnormal behaviour and disease. To investigate how common genetic variants affect the structure of these brain regions, here we conduct genome-wide association studies of the volumes of seven subcortical regions and the intracranial volume derived from magnetic resonance images of 30,717 individuals from 50 cohorts. We identify five novel genetic variants influencing the volumes of the putamen and caudate nucleus. We also find stronger evidence for three loci with previously established influences on hippocampal volume and intracranial volume. These variants show specific volumetric effects on brain structures rather than global effects across structures. The strongest effects were found for the putamen, where a novel intergenic locus with replicable influence on volume (rs945270; P = 1.08×10 -33; 0.52% variance explained) showed evidence of altering the expression of the KTN1 gene in both brain and blood tissue. Variants influencing putamen volume clustered near developmental genes that regulate apoptosis, axon guidance and vesicle transport. Identification of these genetic variants provides insight into the causes of variability in human brain development, and may help to determine mechanisms of neuropsychiatric dysfunction.

Predicting white matter integrity from multiple common genetic variants

Several common genetic variants have recently been discovered that appear to influence white matter microstructure, as measured by diffusion tensor imaging (DTI). Each genetic variant explains only a small proportion of the variance in brain microstructure, so we set out to explore their combined effect on the white matter integrity of the corpus callosum. We measured six common candidate single-nucleotide polymorphisms (SNPs) in the COMT, NTRK1, BDNF, ErbB4, CLU, and HFE genes, and investigated their individual and aggregate effects on white matter structure in 395 healthy adult twins and siblings (age: 20-30 years). All subjects were scanned with 4-tesla 94-direction high angular resolution diffusion imaging. When combined using mixed-effects linear regression, a joint model based on five of the candidate SNPs (COMT, NTRK1, ErbB4, CLU, and HFE) explained ∼ 6% of the variance in the average fractional anisotropy (FA) of the corpus callosum. This predictive model had detectable effects on FA at 82% of the corpus callosum voxels, including the genu, body, and splenium. Predicting the brain's fiber microstructure from genotypes may ultimately help in early risk assessment, and eventually, in personalized treatment for neuropsychiatric disorders in which brain integrity and connectivity are affected.

Identification of common variants associated with human hippocampal and intracranial volumes

Identifying genetic variants influencing human brain structures may reveal new biological mechanisms underlying cognition and neuropsychiatric illness. The volume of the hippocampus is a biomarker of incipient Alzheimer's disease and is reduced in schizophrenia, major depression and mesial temporal lobe epilepsy. Whereas many brain imaging phenotypes are highly heritable, identifying and replicating genetic influences has been difficult, as small effects and the high costs of magnetic resonance imaging (MRI) have led to underpowered studies. Here we report genome-wide association meta-analyses and replication for mean bilateral hippocampal, total brain and intracranial volumes from a large multinational consortium. The intergenic variant rs7294919 was associated with hippocampal volume (12q24.22; N = 21,151; P = 6.70 × 10 -16) and the expression levels of the positional candidate gene TESC in brain tissue. Additionally, rs10784502, located within HMGA2, was associated with intracranial volume (12q14.3; N = 15,782; P = 1.12 × 10 -12). We also identified a suggestive association with total brain volume at rs10494373 within DDR2 (1q23.3; N = 6,500; P = 5.81 × 10 -7).

Characterization of alluvial formation by stochastic modelling of paleo-fluvial processes: The concept and method

Modelling fluvial processes is an effective way to reproduce basin evolution and to recreate riverbed morphology. However, due to the complexity of alluvial environments, deterministic modelling of fluvial processes is often impossible. To address the related uncertainties, we derive a stochastic fluvial process model on the basis of the convective Exner equation that uses the statistics (mean and variance) of river velocity as input parameters. These statistics allow for quantifying the uncertainty in riverbed topography, river discharge and position of the river channel. In order to couple the velocity statistics and the fluvial process model, the perturbation method is employed with a non-stationary spectral approach to develop the Exner equation as two separate equations: the first one is the mean equation, which yields the mean sediment thickness, and the second one is the perturbation equation, which yields the variance of sediment thickness. The resulting solutions offer an effective tool to characterize alluvial aquifers resulting from fluvial processes, which allows incorporating the stochasticity of the paleoflow velocity.

Agent-based simulation as a component of mixed methods in entrepreneurship research

As a new research method supplementing the existing qualitative and quantitative approaches, agent-based modelling and simulation (ABMS) may fit well within the entrepreneurship field because the core concepts and basic premises of entrepreneurship coincide with the characteristics of ABMS (McKelvey, 2004; Yang & Chandra, 2013). Agent-based simulation is a simulation method based on agent-based models. The agentbased models are composed of heterogeneous agents and their behavioural rules. By repeatedly carrying out agent-based simulations on a computer, the simulations reproduce each agent’s behaviour, their interactive process, and the emerging macroscopic phenomenon according to the flow of time. Using agent-based simulations, researchers may investigate temporal or dynamic effects of each agent’s behaviours.

An Uber for apartments could solve some common housing problems

Speculative property developers, criticised for building dog boxes and the slums of tomorrow, are generally hated by urban planners and the public alike. But the doors of state governments are seemingly always open to developers and their lobbyists. Politicians find it hard to say no to the demands of the development industry for concessions because of the contribution housing construction makes to the economic bottom line and because there is a need for well located housing. New supply is also seen as a solution to declining housing affordability. Classical economic theory however is too simplistic for housing supply. Instead, an offshoot of Game Theory - Market Design – not only offers greater insight into apartment supply but also can simultaneously address price, design and quality issues. New research reveals the most significant risk in residential development is settlement risk – when buyers fail to proceed with their purchase despite there being a pre-sale contract. At the point of settlement, the developer has expended all the project funds only to see forecast revenue evaporate. While new buyers may be found, this process is likely to strip the profitability out of the project. As the global financial crisis exposed, buyers are inclined to walk if property values slide. This settlement problem reflects a poor legal mechanism (the pre-sale contract), and a lack of incentive for truthfulness. A second problem is the search costs of finding buyers. At around 10% of project costs, pre-sales are more expensive to developers than finance. This is where Market Design comes in.