Inter-vertebral rotational deformity after endoscopic anterior scoliosis correction may contribute to rib hump recurrence after two years

Introduction. Endoscopic anterior scoliosis correction has been employed recently as a less invasive and level-sparing approach compared with open surgical techniques. We have previously demonstrated that during the two-year post-operative period, there was a mean loss of rib hump correction by 1.4 degrees. The purpose of this study was to determine whether intra- or inter-vertebral rotational deformity during the post-operative period could account for the loss of rib hump correction. Materials and Methods. Ten consecutive patients diagnosed with adolescent idiopathic scoliosis were treated with an endoscopic anterior scoliosis correction. Low-dose computed tomography scans of the instrumented segment were obtained post-operatively at 6 and 24 months following institutional ethical approval and patient consent. Three-dimensional multi-planar reconstruction software (Osirix Imaging Software, Pixmeo, Switzerland) was used to create axial slices of each vertebral level, corrected in both coronal and sagittal planes. Vertebral rotation was measured using Ho’s method for every available superior and inferior endplate at 6 and 24 months. Positive changes in rotation indicate a reduction and improvement in vertebral rotation. Intra-observer variability analysis was performed on a subgroup of images. Results. Mean change in rotation for vertebral endplates between 6 and 24 months post-operatively was -0.26˚ (range -3.5 to 4.9˚) within the fused segment and +1.26˚ (range -7.2 to 15.1˚) for the un-instrumented vertebrae above and below the fusion. Mean change in clinically measured rib hump for the 10 patients was -1.6˚ (range -3 to 0˚). The small change in rotation within the fused segment accounts for only 16.5% of the change in rib hump measured clinically whereas the change in rotation between the un-instrumented vertebrae above and below the construct accounts for 78.8%. There was no clear association between rib hump recurrence and intra- or inter-vertebral rotation in individual patients. Intra-rater variability was ± 3˚. Conclusions. Intra- and inter-vertebral rotation continues post-operatively both within the instrumented and un-instrumented segments of the immature spine. Rotation between the un-instrumented vertebrae above and below the fusion was +1.26˚, suggesting that the un-instrumented vertebrae improved and de-rotated slightly after surgery. This may play a role in rib hump recurrence, however this remains clinically insignificant.

Creep and shrinkage of ultra lightweight cement composite

Creep and shrinkage behaviour of an ultra lightweight cement composite (ULCC) up to 450 days was evaluated in comparison with those of a normal weight aggregate concrete (NWAC) and a lightweight aggregate concrete (LWAC) with similar 28-day compressive strength. The ULCC is characterized by low density < 1500 kg/m3 and high compressive strength about 60 MPa. Autogenous shrinkage increased rapidly in the ULCC at early-age and almost 95% occurred prior to the start of creep test at 28 days. Hence, majority of shrinkage of the ULCC during creep test was drying shrinkage. Total shrinkage of the ULCC during the 450-day creep test was the lowest compared to the NWAC and LWAC. However, corresponding total creep in the ULCC was the highest with high proportion attributed to basic creep (≥ ~90%) and limited drying creep. The high creep of the ULCC is likely due to its low E-modulus. Specific creep of the ULCC was similar to that of the NWAC, but more than 80% higher than the LWAC. Creep coefficient of the ULCC was about 47% lower than that of the NWAC but about 18% higher than that of the LWAC. Among five creep models evaluated which tend to over-estimate the creep coefficient of the ULCC, EC2 model gives acceptable prediction within +25% deviations.

Communication and the casualisation of nursing : a critical ethnography

The contemporary working environment is being rapidly reshaped by technological, industrial and political forces. Increased global competitiveness and an emphasis on productivity have led to the appearance of alternative methods of employment, such as part-time, casual and itinerant work, allowing greater flexibility. This allows for the development of a core permanent staff and the simultaneous utilisation of casual staff according to business needs. Flexible workers across industries are generally referred to as the non-standard workforce and full-time permanent workers as the standard workforce. Even though labour flexibility favours the employer, increased opportunity for flexible work has been embraced by women for many reasons, including the gender struggle for greater economic independence and social equality. Consequently, the largely female nursing industry, both nationally and internationally, has been caught up in this wave of change. This ageing workforce has been at the forefront of the push for flexibility with recent figures showing almost half the nursing workforce is employed in non-standard capacity. In part, this has allowed women to fulfil caring roles outside their work, to ease off nearing retirement and to supplement the family income. More significantly, however, flexibility has developed as an economic management initiative, as a strategy for cost constraint. The result has been the development of a dual workforce and as suggested by Pocock, Buchanan and Campbell (2004), associated deep-seated resentment and the marginalisation of part-time and casual workers by their full-time colleagues and managers. Additionally, as nursing currently faces serious recruitment and retention problems there is urgent need to understand the factors which are underlying present discontent in the nursing profession. There is an identified gap in nursing knowledge surrounding the issues relating to recruitment and retention. Communication involves speaking, listening, reading and writing and is an interactive process which is central to the lives of humans. Workplace communication refers to human interaction, information technology, and multimedia and print. It is the means to relationship building between workers, management, and their external environment and is critical to organisational effectiveness. Communication and language are integral to nursing performance (Hall, 2005), in twenty-four hour service however increasing fragmentation due to part-time and casual work in the nursing industry means that effective communication management has become increasingly difficult. More broadly it is known that disruption to communication systems impacts negatively on consumer outcomes. Because of this gap in understanding how nurses view their contemporary nursing world, an interpretative ethnographic study which progressed to a critical ethnographic study, based on the conceptual framework of constructionism and interpretativism was used. The study site was a division within an acute health care facility, and the relationship between increasing casualisation of the nursing workforce and the experiences of communication of standard and non-standard nurses was explored. For this study, full-time standard nurses were those employed to work in a specific unit for forty hours per week. Non-standard nurses were those employed part-time in specific units or those nurses employed to work as relief pool nurses for shift short falls where needed. Nurses employed by external agencies, but required to fill in for shifts at the facility were excluded from this research. This study involved an analysis of observational, interview and focus group data of standard and non-standard nurses within this facility. Three analytical findings - the organisation of nursing work; constructing the casual nurse as other; and the function of space, situate communication within a broader discussion about non-standard work and organisational culture. The study results suggest that a significant culture of marginalisation exists for nurses who work in a non-standard capacity and that this affects communication for nurses and has implications for the quality of patient care. The discussion draws on the seven elements of marginalisation described by Hall, Stephen and Melius (1994). The arguments propose that these elements underpin a culture which supports remnants of the historically gendered stereotype "the good nurse" and these cultural values contribute to practices and behaviour which marginalise all nurses, particularly those who work less than full-time. Gender inequality is argued to be at the heart of marginalising practices because of long standing subordination of nurses by the powerful medical profession, paralleling historical subordination of women in society. This has denied nurses adequate representation and voice in decision making. The new knowledge emanating from this study extends current knowledge of factors surrounding recruitment and retention and as such contributes to an understanding of the current and complex nursing environment.

A public asset management framework for Indonesian local governments

The decentralisation reform in Indonesia has mandated the Central Government to transfer some functions and responsibilities to local governments including the transfer of human resources, assets and budgets. Local governments became giant asset holders almost overnight and most were ill prepared to handle these transformations. Assets were transferred without analysing local government need, ability or capability to manage the assets and no local government was provided with an asset management framework. Therefore, the aim of this research is to develop a Public Asset Management Framework for provincial governments in Indonesia, especially for infrastructure and real property assets. This framework will enable provincial governments to develop integrated asset management procedures throughout asset‘s lifecycle. Achieving the research aim means answering the following three research questions; 1) How do provincial governments in Indonesia currently manage their public assets? 2) What factors influence the provincial governments in managing these public assets? 3) How is a Public Asset Management Framework developed that is specific for the Indonesian provincial governments‘ situation? This research applied case studies approach after a literature review; document retrieval, interviews and observations were collated. Data was collected in June 2009 (preliminary data collection) and January to July 2010 in the major eastern Indonesian provinces. Once the public asset management framework was developed, a focus group was used to verify the framework. Results are threefold and indicate that Indonesian provincial governments need to improve the effectiveness and efficiency of current practice of public asset management in order to improve public service quality. The second result shows that the 5 major concerns that influence the local government public asset management processes are asset identification and inventory systems, public asset holding, asset guidance and legal arrangements, asset management efficiency and effectiveness, and, human resources and their organisational arrangements. The framework was then applied to assets already transferred to local governments and so included a system of asset identification and a needs analysis to classify the importance of these assets to local governments, their functions and responsibilities in delivering public services. Assets that support local government functions and responsibilities will then be managed using suitable asset lifecycle processes. Those categorised as surplus assets should be disposed. Additionally functions and responsibilities that do not need an asset solution should be performed directly by local governments. These processes must be measured using performance measurement indicators. All these stages should be guided and regulated with sufficient laws and regulations. Constant improvements to the quality and quantity of human resources hold an important role in successful public asset management processes. This research focuses on developing countries, and contributes toward the knowledge of a Public Asset Management Framework at local government level, particularly Indonesia. The framework provides local governments a foundation to improve their effectiveness and efficiency in managing public assets, which could lead to improved public service quality. This framework will ensure that the best decisions are made throughout asset decision ownership and provide a better asset life cycle process, leading to selection of the most appropriate asset, improve its acquisition and delivery process, optimise asset performance, and provide an appropriate disposal program.

Retaining female postgraduates in academia : the role of gender and prospective parenthood

Women remain under-represented in almost all academic levels at universities internationally, and previous evidence has suggested that women move out of the university system in increasing numbers as they progress from postgraduate study to an academic career. The current study aimed to explore the role of gender in the reports of study experiences and future career plans of Australian postgraduate research students (n = 249). Questionnaire data indicated women were significantly less likely than men to rate an academic career as appealing. In particular, female postgraduate students without dependent children were least likely to want to pursue an academic career. On the basis of qualitative analysis, we attribute this finding, at least in part, to a perceived incompatibility between motherhood and an academic career and discuss the implications for gender equity in higher education.

Primary classroom teachers' use of social and emotional wellbeing programs and the factors influencing program use

There has been a rapid escalation in the development and evaluation of social and emotional well-being (SEW) programs in primary schools over the last few decades. Despite the plethora of programs available, primary teachers’ use of SEW programs is not well documented in Australian schools, with even less consideration of the factors influencing program use. A cross-sectional survey was undertaken with primary classroom teachers across twelve schools in the Brisbane and Sunshine Coast Education Districts in Queensland, Australia, during 2005. A checklist of SEW programs and an audit of SEW practices in schools were employed to investigate the number, range and types of SEW programs used by primary classroom teachers and the contextual factors influencing program use. Whilst the majority of implementation studies have been conducted under intervention conditions, this study was designed to capture primary classroom teachers’ day-to-day use of SEW programs and the factors influencing program use under real-world conditions. The findings of this research indicate that almost three quarters of the primary classroom teachers involved in the study reported using at least one SEW program during 2005. Wide variation in the number and range of programs used was evident, suggesting that teachers are autonomous in their use of SEW programs. Evidence-based SEW programs were used by a similar proportion of teachers to non-evidence-based programs. However, irrespective of the type of program used, primary teachers overwhelmingly reported using part of a SEW program rather than the whole program. This raises some issues about the quality of teachers’ program implementation in real-world practice, especially with respect to programs that are evidence-based. A content analysis revealed that a wide range of factors have been examined as potential influences on teachers’ implementation of health promotion programs in schools, including SEW programs, despite the limited number of studies undertaken to date. However, variation in the factors examined and study designs employed both within and across health promotion fields limited the extent to which studies could be compared. A methodological and statistical review also revealed substantial variation in the quality of reporting of studies. A variety of factors were examined as potential influences on primary classroom teachers’ use of SEW programs across multiple social-ecological levels of influence (ranging from community to school and individual levels). In this study, parent or caregiver involvement in class activities and the availability of wellbeing-related policies in primary schools were found to be influential in primary classroom teachers’ use of SEW programs. Teachers who often or always involve parents or caregivers in class activities were at a higher odds of program use relative to teachers who never or rarely involved parents or caregivers in class activities. However, teachers employed in schools with the highest number of wellbeing-related policies available were at a lower odds of program use relative to teachers employed in schools with fewer wellbeing-related policies available. Future research should investigate primary classroom teachers’ autonomy and motivations for using SEW programs and the reasons behind the selection and use of particular types of programs. A larger emphasis should also be placed upon teachers not using SEW programs to identify valid reasons for non-use. This would provide another step towards bridging the gap between the expectations of program developers and the needs of teachers who implement programs in practice. Additionally, the availability of wellbeing-related school policies and the types of activities that parents and caregivers are involved with in the classroom warrant more in-depth investigation. This will help to ascertain how and why these factors influence primary classroom teachers’ use of SEW programs on a day-to-day basis in schools.

Improving ultrasound excitation systems using a flexible power supply with adjustable voltage and frequency to drive piezoelectric transducers

The ability of a piezoelectric transducer in energy conversion is rapidly expanding in several applications. Some of the industrial applications for which a high power ultrasound transducer can be used are surface cleaning, water treatment, plastic welding and food sterilization. Also, a high power ultrasound transducer plays a great role in biomedical applications such as diagnostic and therapeutic applications. An ultrasound transducer is usually applied to convert electrical energy to mechanical energy and vice versa. In some high power ultrasound system, ultrasound transducers are applied as a transmitter, as a receiver or both. As a transmitter, it converts electrical energy to mechanical energy while a receiver converts mechanical energy to electrical energy as a sensor for control system. Once a piezoelectric transducer is excited by electrical signal, piezoelectric material starts to vibrate and generates ultrasound waves. A portion of the ultrasound waves which passes through the medium will be sensed by the receiver and converted to electrical energy. To drive an ultrasound transducer, an excitation signal should be properly designed otherwise undesired signal (low quality) can deteriorate the performance of the transducer (energy conversion) and increase power consumption in the system. For instance, some portion of generated power may be delivered in unwanted frequency which is not acceptable for some applications especially for biomedical applications. To achieve better performance of the transducer, along with the quality of the excitation signal, the characteristics of the high power ultrasound transducer should be taken into consideration as well. In this regard, several simulation and experimental tests are carried out in this research to model high power ultrasound transducers and systems. During these experiments, high power ultrasound transducers are excited by several excitation signals with different amplitudes and frequencies, using a network analyser, a signal generator, a high power amplifier and a multilevel converter. Also, to analyse the behaviour of the ultrasound system, the voltage ratio of the system is measured in different tests. The voltage across transmitter is measured as an input voltage then divided by the output voltage which is measured across receiver. The results of the transducer characteristics and the ultrasound system behaviour are discussed in chapter 4 and 5 of this thesis. Each piezoelectric transducer has several resonance frequencies in which its impedance has lower magnitude as compared to non-resonance frequencies. Among these resonance frequencies, just at one of those frequencies, the magnitude of the impedance is minimum. This resonance frequency is known as the main resonance frequency of the transducer. To attain higher efficiency and deliver more power to the ultrasound system, the transducer is usually excited at the main resonance frequency. Therefore, it is important to find out this frequency and other resonance frequencies. Hereof, a frequency detection method is proposed in this research which is discussed in chapter 2. An extended electrical model of the ultrasound transducer with multiple resonance frequencies consists of several RLC legs in parallel with a capacitor. Each RLC leg represents one of the resonance frequencies of the ultrasound transducer. At resonance frequency the inductor reactance and capacitor reactance cancel out each other and the resistor of this leg represents power conversion of the system at that frequency. This concept is shown in simulation and test results presented in chapter 4. To excite a high power ultrasound transducer, a high power signal is required. Multilevel converters are usually applied to generate a high power signal but the drawback of this signal is low quality in comparison with a sinusoidal signal. In some applications like ultrasound, it is extensively important to generate a high quality signal. Several control and modulation techniques are introduced in different papers to control the output voltage of the multilevel converters. One of those techniques is harmonic elimination technique. In this technique, switching angles are chosen in such way to reduce harmonic contents in the output side. It is undeniable that increasing the number of the switching angles results in more harmonic reduction. But to have more switching angles, more output voltage levels are required which increase the number of components and cost of the converter. To improve the quality of the output voltage signal with no more components, a new harmonic elimination technique is proposed in this research. Based on this new technique, more variables (DC voltage levels and switching angles) are chosen to eliminate more low order harmonics compared to conventional harmonic elimination techniques. In conventional harmonic elimination method, DC voltage levels are same and only switching angles are calculated to eliminate harmonics. Therefore, the number of eliminated harmonic is limited by the number of switching cycles. In the proposed modulation technique, the switching angles and the DC voltage levels are calculated off-line to eliminate more harmonics. Therefore, the DC voltage levels are not equal and should be regulated. To achieve this aim, a DC/DC converter is applied to adjust the DC link voltages with several capacitors. The effect of the new harmonic elimination technique on the output quality of several single phase multilevel converters is explained in chapter 3 and 6 of this thesis. According to the electrical model of high power ultrasound transducer, this device can be modelled as parallel combinations of RLC legs with a main capacitor. The impedance diagram of the transducer in frequency domain shows it has capacitive characteristics in almost all frequencies. Therefore, using a voltage source converter to drive a high power ultrasound transducer can create significant leakage current through the transducer. It happens due to significant voltage stress (dv/dt) across the transducer. To remedy this problem, LC filters are applied in some applications. For some applications such as ultrasound, using a LC filter can deteriorate the performance of the transducer by changing its characteristics and displacing the resonance frequency of the transducer. For such a case a current source converter could be a suitable choice to overcome this problem. In this regard, a current source converter is implemented and applied to excite the high power ultrasound transducer. To control the output current and voltage, a hysteresis control and unipolar modulation are used respectively. The results of this test are explained in chapter 7.

First principle study of hydrogenation of MgB2 : an important step toward reversible hydrogen storage in the coupled LiBH4/MgH2 system

Recent experiments [F. E. Pinkerton, M. S. Meyer, G. P. Meisner, M. P. Balogh, and J. J. Vajo, J. Phys. Chem. C 111, 12881 (2007) and J. J. Vajo and G. L. Olson, Scripta Mater. 56, 829 (2007)] demonstrated that the recycling of hydrogen in the coupled LiBH4/MgH2 system is fully reversible. The rehydrogenation of MgB2 is an important step toward the reversibility. By using ab initio density functional theory calculations, we found that the activation barrier for the dissociation of H2 are 0.49 and 0.58 eV for the B and Mg-terminated MgB2(0001) surface, respectively. This implies that the dissociation kinetics of H2 on a MgB2 (0001) surface should be greatly improved compared to that in pure Mg materials. Additionally, the diffusion of dissociated H atom on the Mg-terminated MgB2(0001) surface is almost barrier-less. Our results shed light on the experimentally-observed reversibility and improved kinetics for the coupled LiBH4/MgH2 system.

Social Media Sites as Online Information Grounds : An exploratory study of the ways in which Information Technology (IT) professionals experience social media

Social media tools are often the result of innovations in Information Technology and developed by IT professionals and innovators. Nevertheless, IT professionals, many of whom are responsible for designing and building social media technologies, have not been investigated on how they themselves use or experience social media for professional purposes. This study will use Information Grounds Theory (Pettigrew, 1998) as a framework to study IT professionals’ experience in using social media for professional purposes. Information grounds facilitates the opportunistic discovery of information within social settings created temporarily at a place where people gather for a specific purpose (e.g., doctors’ waiting rooms, office tea rooms etc.), but the social atmosphere stimulates spontaneous sharing of information (Pettigrew, 1999). This study proposes that social media has the qualities that make it a rich information grounds; people participate from separate “places” in cyberspace in a synchronous manner in real-time, making it almost as dynamic and unplanned as physical information grounds. There is limited research on how social media platforms are perceived as a “place,” (a place to go to, a place to gather, or a place to be seen in) that is comparable to physical spaces. There is also no empirical study on how IT professionals use or “experience” social media. The data for this study is being collected through a study of IT professionals who currently use Twitter. A digital ethnography approach is being taken wherein the researcher uses online observations and “follows” the participants online and observes their behaviours and interactions on social media. Next, a sub-set of participants will be interviewed on their experiences with and within social media and how social media compares with traditional methods of information grounds, information communication, and collaborative environments. An Evolved Grounded Theory (Glaser, 1992) approach will be used to analyse tweets data and interviews and to map the findings against the Information Ground Theory. Findings from this study will provide foundational understanding of IT professionals’ experiences within social media, and can help both professionals and researchers understand this fast-evolving method of communications.

Inflow cannula design for biventricular assist devices

Cardiovascular diseases are a leading cause of death throughout the developed world. With the demand for donor hearts far exceeding the supply, a bridge-to-transplant or permanent solution is required. This is currently achieved with ventricular assist devices (VADs), which can be used to assist the left ventricle (LVAD), right ventricle (RVAD), or both ventricles simultaneously (BiVAD). Earlier generation VADs were large, volume-displacement devices designed for temporary support until a donor heart was found. The latest generation of VADs use rotary blood pump technology which improves device lifetime and the quality of life for end stage heart failure patients. VADs are connected to the heart and greater vessels of the patient through specially designed tubes called cannulae. The inflow cannulae, which supply blood to the VAD, are usually attached to the left atrium or ventricle for LVAD support, and the right atrium or ventricle for RVAD support. Few studies have characterized the haemodynamic difference between the two cannulation sites, particularly with respect to rotary RVAD support. Inflow cannulae are usually made of metal or a semi-rigid polymer to prevent collapse with negative pressures. However suction, and subsequent collapse, of the cannulated heart chamber can be a frequent occurrence, particularly with the relatively preload insensitive rotary blood pumps. Suction events may be associated with endocardial damage, pump flow stoppages and ventricular arrhythmias. While several VAD control strategies are under development, these usually rely on potentially inaccurate sensors or somewhat unreliable inferred data to estimate preload. Fixation of the inflow cannula is usually achieved through suturing the cannula, often via a felt sewing ring, to the cannulated chamber. This technique extends the time on cardiopulmonary bypass which is associated with several postoperative complications. The overall objective of this thesis was to improve the placement and design of rotary LVAD and RVAD inflow cannulae to achieve enhanced haemodynamic performance, reduced incidence of suction events, reduced levels of postoperative bleeding and a faster implantation procedure. Specific objectives were: * in-vitro evaluation of LVAD and RVAD inflow cannula placement, * design and in-vitro evaluation of a passive mechanism to reduce the potential for heart chamber suction, * design and in-vitro evaluation of a novel suture-less cannula fixation device. In order to complete in-vitro evaluation of VAD inflow cannulae, a mock circulation loop (MCL) was developed to accurately replicate the haemodynamics in the human systemic and pulmonary circulations. Validation of the MCL’s haemodynamic performance, including the form and magnitude of pressure, flow and volume traces was completed through comparisons of patient data and the literature. The MCL was capable of reproducing almost any healthy or pathological condition, and provided a useful tool to evaluate VAD cannulation and other cardiovascular devices. The MCL was used to evaluate inflow cannula placement for rotary VAD support. Left and right atrial and ventricular cannulation sites were evaluated under conditions of mild and severe heart failure. With a view to long term LVAD support in the severe left heart failure condition, left ventricular inflow cannulation was preferred due to improved LVAD efficiency and reduced potential for thrombus formation. In the mild left heart failure condition, left atrial cannulation was preferred to provide an improved platform for myocardial recovery. Similar trends were observed with RVAD support, however to a lesser degree due to a smaller difference in right atrial and ventricular pressures. A compliant inflow cannula to prevent suction events was then developed and evaluated in the MCL. As rotary LVAD or RVAD preload was reduced, suction events occurred in all instances with a rigid inflow cannula. Addition of the compliant segment eliminated suction events in all instances. This was due to passive restriction of the compliant segment as preload dropped, thus increasing the VAD circuit resistance and decreasing the VAD flow rate. Therefore, the compliant inflow cannula acted as a passive flow control / anti-suction system in LVAD and RVAD support. A novel suture-less inflow cannula fixation device was then developed to reduce implantation time and postoperative bleeding. The fixation device was evaluated for LVAD and RVAD support in cadaveric animal and human hearts attached to a MCL. LVAD inflow cannulation was achieved in under two minutes with the suture-less fixation device. No leakage through the suture-less fixation device – myocardial interface was noted. Continued development and in-vivo evaluation of this device may result in an improved inflow cannulation technique with the potential for off-bypass insertion. Continued development of this research, in particular the compliant inflow cannula and suture-less inflow cannulation device, will result in improved postoperative outcomes, life span and quality of life for end-stage heart failure patients.

Lessons from media reporting of natural disasters : a case study of the 2011 flash floods in Toowoomba and the Lockyer Valley

Practice-led journalism research techniques were used in this study to produce a ‘first draft of history’ recording the human experience of survivors and rescuers during the January 2011 flash flood disaster in Toowoomba and the Lockyer Valley in Queensland, Australia. The study aimed to discover what can be learnt from engaging in journalistic reporting of natural disasters. This exegesis demonstrates that journalism can be both a creative practice and a research methodology. About 120 survivors, rescuers and family members of victims participated in extended interviews about what happened to them and how they survived. Their stories are the basis for two creative outputs of the study: a radio documentary and a non-fiction book, that document how and why people died, or survived, or were rescued. Listeners and readers are taken "into the flood" where they feel anxious for those in peril, relief when people are saved, and devastated when babies, children and adults are swept away to their deaths. In undertaking reporting about the human experience of the floods, several significant elements about journalistic reportage of disasters were exposed. The first related to the vital role that the online social media played during the disaster for individuals, citizen reporters, journalists and emergency services organisations. Online social media offer reporters powerful new reporting tools for both gathering and disseminating news. The second related to the performance of journalists in covering events involving traumatic experiences. Journalists are often required to cover trauma and are often amongst the first-responders to disasters. This study found that almost all of the disaster survivors who were approached were willing to talk in detail about their traumatic experiences. A finding of this project is that journalists who interview trauma survivors can develop techniques for improving their ability to interview people who have experienced traumatic events. These include being flexible with interview timing and selecting a location; empowering interviewees to understand they don’t have to answer every question they are asked; providing emotional security for interviewees; and by being committed to accuracy. Survivors may exhibit posttraumatic stress symptoms but some exhibit and report posttraumatic growth. The willingness of a high proportion of the flood survivors to participate in the flood research made it possible to document a relatively unstudied question within the literature about journalism and trauma – when and why disaster survivors will want to speak to reporters. The study sheds light on the reasons why a group of traumatised people chose to speak about their experiences. Their reasons fell into six categories: lessons need to be learned from the disaster; a desire for the public to know what had happened; a sense of duty to make sure warning systems and disaster responses to be improved in future; personal recovery; the financial disinterest of reporters in listening to survivors; and the timing of the request for an interview. Feedback to the creative-practice component of this thesis - the book and radio documentary - shows that these issues are not purely matters of ethics. By following appropriate protocols, it is possible to produce stories that engender strong audience responses such as that the program was "amazing and deeply emotional" and "community storytelling at its most important". Participants reported that the experience of the interview process was "healing" and that the creative outcome resulted in "a very precious record of an afternoon of tragedy and triumph and the bitter-sweetness of survival".

Methyl ester preparation from peanut oil and its effect on DI diesel engine combustion

This study investigated the preparation of methyl ester (Biodiesel) from peanut oil by transesterification method and its effect on DI diesel engine. Two parameters were measured during the engine operation: one is engine performance (brake thermal efficiency and brake specific fuel consumption), and the other is the exhaust emissions (NOx and CO). The result showed that, when compared with neat diesel fuel, the brake thermal efficiency of biodiesel blend was almost similar or a slight lower. However, brake specific fuel consumption (bsfc) was a little higher than neat diesel. CO was lower and NOx was little higher with biodiesel blend than that of diesel. The engine performance for B10 and B20 was very similar. At medium and high load conditions the engine emissions for B10 and B20 has no significant variation. Hence, B20 can safely be used in diesel engine without any significant penalty in engine performance and emissions.

Differences in the symptom experience of older versus younger oncology outpatients : a cross-sectional study

Background: Mortality rates for cancer are decreasing in patients under 60 and increasing in those over 60 years of age. The reasons for these differences in mortality rates remain poorly understood. One explanation may be that older patients received substandard treatment because of concerns about adverse effects. Given the paucity of research on the multiple dimensions of the symptom experience in older oncology patients, the purpose of this study was to evaluate for differences in ratings of symptom occurrence, severity, frequency, and distress between younger (< 60 years) and older ( ≥ 60 years) adults undergoing cancer treatment. We hypothesized that older patients would have significantly lower ratings on four symptom dimensions. Methods: Data from two studies in the United States and one study in Australia were combined to conduct this analysis. All three studies used the MSAS to evaluate the occurrence, severity, frequency, and distress of 32 symptoms. Results: Data from 593 oncology outpatients receiving active treatment for their cancer (i.e., 44.4% were < 60 years and 55.6% were ≥ 60 years of age) were evaluated. Of the 32 MSAS symptoms, after controlling for significant covariates, older patients reported significantly lower occurrence rates for 15 (46.9%) symptoms, lower severity ratings for 6 (18.9%) symptoms, lower frequency ratings for 4 (12.5%) symptoms, and lower distress ratings for 14 (43.8%) symptoms. Conclusions: This study is the first to evaluate for differences in multiple dimensions of symptom experience in older oncology patients. For almost 50% of the MSAS symptoms, older patients reported significantly lower occurrence rates. While fewer age-related differences were found in ratings of symptom severity, frequency, and distress, a similar pattern was found across all three dimensions. Future research needs to focus on a detailed evaluation of patient and clinical characteristics (i.e., type and dose of treatment) that explain the differences in symptom experience identified in this study.

Raman and infrared spectroscopic study of the mineral goyazite SrAl3(PO4)2(OH)5·H2O

We have studied the mineral goyazite using Raman and infrared spectroscopy. Goyazite is a member of the crandallite subgroup of the alunite supergroup. The crystal structure is of the alunite-type and consists of sheets of corner-sharing AlO6 octahedra parallel to (0001). The octahedrally coordinated Sr2+ cations occupy cavities between pairs of octahedral sheets and are surrounded by six oxygen atoms from the (Al3+)O6 octahedra. The very intense sharp band at 983 cm-1 is assigned to the ν1 PO43- symmetric stretching mode. The observation of a single band supports the concept that all the phosphate units are equivalent in the structure of goyazite. Raman bands observed at 1029 cm-1 and 1037 cm-1 are assigned to the to the ν3 PO43- antisymmetric stretching vibrations. Two Raman bands at 895 and 927 cm-1 are attributed to the stretching vibrations of H2PO4; thus indicating some hydrogen phosphate units in the structure of goyazite. Raman bands at 556, 581, 596 and 612 cm-1 are assigned to the ν4 PO43- bending modes, suggesting a reduction of symmetry of phosphate units. Two sharp Raman bands at 3609 and 3631 cm-1 are attributed to OH stretching vibrations from the goyazite hydroxyl units. Broad Raman bands at 2924, 3043, 3210, 3429 and 3511 cm-1 are assigned to water stretching vibrations. Vibrational spectroscopy enables subtle details of the molecular structure of goyazite to be determined.

Caught on camera

The emergence of shopping malls in Europe, the UK and Australia over the last thirty years or so, raises questions about the disruptive effects of such capital intensive developments on local area shopping facilities, transport and other infrastructures and the maintenance of artificially high prices for goods, whereby the promised greater choice of shops and prices is rarely a genuine free market of competition leading to lower prices. A central question to be addressed is whom these centres represent and belong to. While many claim to exist to ‘serve the community’ almost all malls and centres are private property and the community of shoppers has few, if any rights compared with the conventional high street, which is a public thoroughfare. This permits the management of the centres through their own private security staff, to observe, follow, eject and refuse further admission to anyone considered to be ‘undesirable’. What is different about the newest shopping centres is the routine use of increasingly sophisticated CCTV surveillance equipment to observe and record, for later evidential and entry restriction use, the movements of centre visitors.