Analytical modeling and sensitivity analysis for travel time estimation on signalized urban networks

This paper presents a model for estimation of average travel time and its variability on signalized urban networks using cumulative plots. The plots are generated based on the availability of data: a) case-D, for detector data only; b) case-DS, for detector data and signal timings; and c) case-DSS, for detector data, signal timings and saturation flow rate. The performance of the model for different degrees of saturation and different detector detection intervals is consistent for case-DSS and case-DS whereas, for case-D the performance is inconsistent. The sensitivity analysis of the model for case-D indicates that it is sensitive to detection interval and signal timings within the interval. When detection interval is integral multiple of signal cycle then it has low accuracy and low reliability. Whereas, for detection interval around 1.5 times signal cycle both accuracy and reliability are high.

Estimation of travel time on urban networks with midlink sources and sinks

This paper presents a methodology for estimation of average travel time on signalized urban networks by integrating cumulative plots and probe data. This integration aims to reduce the relative deviations in the cumulative plots due to midlink sources and sinks. During undersaturated traffic conditions, the concept of a virtual probe is introduced, and therefore, accurate travel time can be obtained when a real probe is unavailable. For oversaturated traffic conditions, only one probe per travel time estimation interval—360 s or 3% of vehicles traversing the link as a probe—has the potential to provide accurate travel time.

Voltage unbalance reduction in low voltage distribution networks with rooftop PVs

Voltage Unbalance (VU) is a power quality issue arising within the low voltage residential distribution networks due to the random location and rating of single-phase rooftop photovoltaic cells (PVs). In this paper, an analysis has been carried out to investigate how PV installations, their random location and power generation capacity can cause an increase in VU. Several efficient practical methods are discussed for VU reduction. Based on this analysis, it has been shown that the installation of a DSTATCOM can reduce VU. In this paper, the best possible location for DSTATCOM and its efficient control method to reduce VU will be presented. The results are verified through PSCAD/EMTDC and Monte Carlo simulations.

Social inclusion through community enterprise? Examining the available evidence

In recent years the concepts of social inclusion and exclusion have become part of the repertoire of third-way policy discourses that seek to respond to complex socioeconomic problems through processes of 'joined-up' and 'integrated' governance. As part of this approach, we are witnessing an increased focus on the role of the third sector in facilitating social inclusion. While the push towards governing through networks has gained moral legitimacy in some areas of social policy, the practical legitimacy - that is, whether these new approaches actually produce demonstrably better outcomes than more traditional policy approaches - remains largely unsubstantiated. This article contributes to the evidence base, by examining the social-inclusion impacts of eleven community enterprises operating in Victoria, and to the wider available evidence on the social, economic and civic effects of social enterprise.

The application of neural networks to induction machine control

Neural networks (NNs) are discussed in connection with their possible use in induction machine drives. The mathematical model of the NN as well as a commonly used learning algorithm is presented. Possible applications of NNs to induction machine control are discussed. A simulation of an NN successfully identifying the nonlinear multivariable model of an induction-machine stator transfer function is presented. Previously published applications are discussed, and some possible future applications are proposed.

Identification and control of induction machines using artificial neural networks

The use of artificial neural networks (ANNs) to identify and control induction machines is proposed. Two systems are presented: a system to adaptively control the stator currents via identification of the electrical dynamics, and a system to adaptively control the rotor speed via identification of the mechanical and current-fed system dynamics. Both systems are inherently adaptive as well as self-commissioning. The current controller is a completely general nonlinear controller which can be used together with any drive algorithm. Various advantages of these control schemes over conventional schemes are cited, and the combined speed and current control scheme is compared with the standard vector control scheme

Identification and control of induction machines using artificial neural networks

This paper proposes the use of artificial neural networks (ANNs) to identify and control an induction machine. Two systems are presented: a system to adaptively control the stator currents via identification of the electrical dynamics; and a system to adaptively control the rotor speed via identification of the mechanical and current-fed system dynamics. Various advantages of these control schemes over other conventional schemes are cited and the performance of the combined speed and current control scheme is compared with that of the standard vector control scheme

Assessment of the suitability of public mobile data networks for aircraft telemetry and control purposes

This paper provides a review of the state of the art relevant work on the use of public mobile data networks for aircraft telemetry and control proposes. Moreover, it describes the characterisation for airborne uses of the public mobile data communication systems known broadly as 3G. The motivation for this study was the explore how this mature public communication systems could be used for aviation purposes. An experimental system was fitted to a light aircraft to record communication latency, line speed, RF level, packet loss and cell tower identifier. Communications was established using internet protocols and connection was made to a local server. The aircraft was flown in both remote and populous areas at altitudes up to 8500 ft in a region located in South East Queensland, Australia. Results show that the average airborne RF levels are better than those on the ground by 21% and in the order of - 77dbm. Latencies were in the order of 500ms (1/2 the latency of Iridium), an average download speed of 0.48Mb/s, average uplink speed of 0.85Mb/s, a packet of information loss of 6.5%. The maximum communication range was also observed to be 70km from a single cell station. The paper also describes possible limitations and utility of using such communications architecture for both manned and unmanned aircraft systems.

Pockets of creativity in business processes

Creative processes, for instance, the development of visual effects or computer games, increasingly become part of the agenda of information systems researchers and practitioners. Such processes get their managerial challenges from the fact that they comprise both well-structured, transactional parts and creative parts. The latter can often not be precisely specified in terms of control flow, required resources, and outcome. The processes’ high uncertainty sets boundaries for the application of traditional business process management concepts, such as process automation, process modeling, process performance measurement, and risk management. Organizations must thus exercise caution when it comes to managing creative processes and supporting these with information technology. This, in turn, requires a profound understanding of the concept of creativity in business processes. In response to this, the present paper introduces a framework for conceptualizing creativity within business processes. The conceptual framework describes three types of uncertainty and constraints as well as the interrelationships among these. The study is grounded in the findings from three case studies that were conducted in the film and visual effects industry. Moreover, we provide initial evidence for the framework’s validity beyond this narrow focus. The framework is intended to serve as a sensitizing device that can guide further information systems research on creativity-related phenomena.

Communication patterns within social networks : a case study of Australian women

Based on the perception that “individual bonds to one another is the essence of society” (Fischer, 1982a, p. 2), this paper examines contemporary networks of friends: friendworks, of adult women in an Australian sea change community. Communication patterns are examined drawing on findings from a case study of 26 women aged 35-76 years. Among the case study participants, many have undertaken a ‘sea change’ as adults, which in most cases has led to a significant reconstruction of their friendworks. Location and lifestyle are identified as impacting factors on communication patterns with friends; face-to-face interactions are by far the most frequent and preferred method of communication among the participants. The landline telephone and internet are the main communication methods used to maintain friendships with distant loved ones, while the mobile phone is reported as the communication method employed the least. The infrequency of mobile phone use can be attributed to cost issues, highlighting a discrepancy between these women’s social and communication needs and the current Australian mobile phone policy.

Invention and business performance in the tissue-engineering industry

Tissue engineering is a young and interdisciplinary scientific discipline but it offers exciting opportunities to improve the quality of health care for hundreds of thousands of patients. Lured by its potential, several start-up companies, pharmaceutical corporations, and medical device enterprises alike are investing heavily in this sector. Invention is a key driver of competition in this sector. In this study, we aim to explain the variation in inventive output across the different firms in the sector. Our major premise is that firms that forge alliances will be able to tap into the expertise of their partners and thus improve their chances of inventive output. We further argue that alliances that enable technology acquisition or learning will enhance the inventive output of firms more than other kinds of alliances. We measure the inventive output of a company by the number of patents filed. On the basis of a preliminary analysis of seven companies, we find support for the hypotheses. We also argue that, to achieve commercial success, firms need to manage time to market (through alliances or otherwise), have a global outlook, nurture their financial resources, and attain critical mass through mergers.