Integrated plasma-aided nanofabrication facility: Operation, parameters, and assembly of quantum structures and functional nanomaterials

The development, operation, and applications of two configurations of an integrated plasma-aided nanofabrication facility (IPANF) comprising low-frequency inductively coupled plasma-assisted, low-pressure, multiple-target RF magnetron sputtering plasma source, are reported. The two configurations of the plasma source have different arrangements of the RF inductive coil: a conventional external flat spiral "pancake" coil and an in-house developed internal antenna comprising two orthogonal RF current sheets. The internal antenna configuration generates a "unidirectional" RF current that deeply penetrates into the plasma bulk and results in an excellent uniformity of the plasma over large areas and volumes. The IPANF has been employed for various applications, including low-temperature plasma-enhanced chemical vapor deposition of vertically aligned single-crystalline carbon nanotips, growth of ultra-high aspect ratio semiconductor nanowires, assembly of optoelectronically important Si, SiC, and Al1-xInxN quantum dots, and plasma-based synthesis of bioactive hydroxyapatite for orthopedic implants.

Microscopic ion fluxes in plasma-aided nanofabrication of ordered carbon nanotip structures

Three-dimensional topography of microscopic ion fluxes in the reactive hydrocarbon-based plasma-aided nanofabrication of ordered arrays of vertically aligned single-crystalline carbon nanotip microemitter structures is simulated by using a Monte Carlo technique. The individual ion trajectories are computed by integrating the ion equations of motion in the electrostatic field created by a biased nanostructured substrate. It is shown that the ion flux focusing onto carbon nanotips is more efficient under the conditions of low potential drop Us across the near-substrate plasma sheath. Under low- Us conditions, the ion current density onto the surface of individual nanotips is higher for higher-aspect-ratio nanotips and can exceed the mean ion current density onto the entire nanopattern in up to approximately five times. This effect becomes less pronounced with increasing the substrate bias, with the mean relative enhancement of the ion current density ξi not exceeding ∼1.7. The value of ξi is higher in denser plasmas and behaves differently with the electron temperature Te depending on the substrate bias. When the substrate bias is low, ξi decreases with Te, with the opposite tendency under higher- Us conditions. The results are relevant to the plasma-enhanced chemical-vapor deposition of ordered large-area nanopatterns of vertically aligned carbon nanotips, nanofibers, and nanopyramidal microemitter structures for flat-panel display applications. © 2005 American Institute of Physics.

Electron transport across magnetic field in low-temperature plasmas : an alternative approach for obtaining evidence of Bohm mechanism

A comparative study involving both experimental and numerical investigations was made to resolve a long-standing problem of understanding electron conductivity mechanism across magnetic field in low-temperature plasmas. We have calculated the plasma parameters from experimentally obtained electric field distribution, and then made a 'back' comparison with the distributions of electron energy and plasma density obtained in the experiment. This approach significantly reduces an influence of the assumption about particular phenomenology of the electron conductivity in plasma. The results of the experiment and calculations made by this technique have showed that the classical conductivity is not capable of providing realistic total current and electron energy, whereas the phenomenological anomalous Bohm mobility has demonstrated a very good agreement with the experiment. These results provide an evidence in favor of the Bohm conductivity, thus making it possible to clarify this pressing long-living question about the main driving mechanism responsible for the electron transport in low-temperature plasmas.

Unconventional Ni–P alloy-catalyzed CVD of carbon coil-like micro- and nano-structures

Conventional catalyzed thermal CVD of carbon microcoils commonly suffers from poor control of the coil shape and morphology and rarely reaches the nanoscale size range. This article reports on an unconventional Ni-P alloy-catalyzed, high-throughput, highly reproducible CVD of ultra-long carbon coil-like micro- and nano-structures using acetylene precursor at relatively low process temperatures. Helical carbon microcoils with consistently uniform, circular cross-sections and a high degree of crystallinity have been synthesized at 750 °C. A further reduction of the temperature to 650 °C led to the growth of ultra-long (up to several mm) wave-like carbon nanofibers made of two nanowires with the diameters in the 100-200 nm range. The results of the XRD and Raman analysis reveal that the nanofibers feature only a slightly more disordered structure compared to the microcoils. Our results suggest that morphology and structure of the carbon coil-like micro- and nano-structures can be tailored by the appropriate alloying of the catalyst and the choice of the CVD process parameters.

Nanopowder management and plasma parameters in nanofabrication of low-dimensional quantum structures in reactive silane-based plasmas

Management of nanopowder and reactive plasma parameters in a low-pressure RF glow discharge in silane is studied. It is shown that the discharge control parameters and reactor volume can be adjusted to ensure lower abundance of nanopowders, which is one of the requirements of the plasma-assisted fabrication of low-dimensional quantum nanostructures. The results are relevant to micro- and nanomanufacturing technologies employing low-pressure glow discharge plasmas of silane-based gas mixtures.

Growth kinetics of carbon nanowall-like structures in low-temperature plasmas

The results of a hybrid numerical simulation of the growth kinetics of carbon nanowall-like nanostructures in the plasma and neutral gas synthesis processes are presented. The low-temperature plasma-based process was found to have a significant advantage over the purely neutral flux deposition in providing the uniform size distribution of the nanostructures. It is shown that the nanowall width uniformity is the best (square deviations not exceeding 1.05) in high-density plasmas of 3.0× 1018 m-3, worsens in lower-density plasmas (up to 1.5 in 1.0× 1017 m-3 plasmas), and is the worst (up to 1.9) in the neutral gas-based process. This effect has been attributed to the focusing of ion fluxes by irregular electric field in the vicinity of plasma-grown nanostructures on substrate biased with -20 V potential, and differences in the two-dimensional adatom diffusion fluxes in the plasma and neutral gas-based processes. The results of our numerical simulations are consistent with the available experimental reports on the effect of the plasma process parameters on the sizes and shapes of relevant nanostructures.

Self-assembly of uniform carbon nanotip structures in chemically active inductively coupled plasmas

Self-assembly of carbon nanotip (CNTP) structures on Ni-based catalyst in chemically active inductively coupled plasmas of CH 4 + H 2 + Ar gas mixtures is reported. By varying the process conditions, it appears possible to control the shape, size, and density of CNTPs, content of the nanocrystalline phase in the films, as well as to achieve excellent crystallinity, graphitization, uniformity and vertical alignment of the resulting nanostructures at substrate temperatures 300-500°C and low gas pressures (below 13.2 Pa). This study provides a simple and efficient plasma-enhanced chemical vapor deposition (PECVD) technique for the fabrication of vertically aligned CNTP arrays for electron field emitters.

Shear capacities of rivet fastened Rectangular Hollow Flange Channel Beams

The intermittently rivet fastened Rectangular Hollow Flange Channel Beam (RHFCB) is a new cold-formed hollow section proposed as an alternative to welded hollow flange beams. It is a monosymmetric channel section made by intermittently rivet fastening two torsionally rigid rectangular hollow flanges to a web plate. This method will allow the development of optimum sections by choosing appropriate combinations of web and flange plate widths and thicknesses. RHFCBs can be commonly used as flexural members in buildings. Many experimental and numerical studies have been carried out in the past to investigate the shear behaviour of lipped channel beams. However, no research has been undertaken on the shear behaviour of rivet fastened RHFCBs. Therefore a detailed experimental study involving 19 shear tests was undertaken to investigate the shear behaviour and capacities of rivet fastened RHFCBs. Simply supported test specimens of RHFCB with aspect ratios of 1.0 and 1.5 were loaded at mid-span until failure. Comparison of experimental results with corresponding predictions from the current Australian cold-formed steel design rules showed that the current design rules are very conservative for the shear design of rivet fastened RHFCBs. Significant improvements to web shear buckling occurred due to the presence of rectangular hollow flanges while considerable post-buckling strength was also observed. Appropriate improvements have been proposed for the design rules of shear strength of rivet fastened RHFCBs within the Direct Strength Method format. This paper presents the details of this study and the results.

Delivery of therapeutic molecules using electrosprayed polymeric particles for applications in tissue engineering

This thesis has developed an innovative technology, electrospraying, that allows biodegradable microparticles to deliver pharmaceuticals that aid bone regeneration. The establishment, characterisation and optimisation of the technique are a step forward in developing an affordable and safe alternative to the products used currently in the clinical setting for the treatment of musculoskeletal disorders. The researcher has also investigated electrospraying as a coating technique on biodegradable structures that are used to replace damaged tissues, in order to provide localised and efficient drug delivery in the site of the defect to help tissue reconstruction.

Harvesting as an alternative to burning for managing Spinifex Grasslands in Australia

Sustainable harvesting of grasslands can buffer large scale wildfires and the harvested biomass can be used for various products. Spinifex (Triodia spp.) grasslands cover ≈30% of the Australian continent and form the dominant vegetation in the driest regions. Harvesting near settlements is being considered as a means to reduce the occurrence and intensity of wildfires and to source biomaterials for sustainable desert living. However, it is unknown if harvesting spinifex grasslands can be done sustainably without loss of biodiversity and ecosystem function. We examined the trajectory of plant regeneration of burned and harvested spinifex grassland, floristic diversity, nutrient concentrations in soil and plants, and seed germination in controlled ex situ conditions. After two to three years of burning or harvesting in dry or wet seasons, species richness, diversity, and concentrations of most nutrients in soil and leaves of regenerating spinifex plants were overall similar in burned and harvested plots. Germination tests showed that 20% of species require fire-related cues to trigger germination, indicating that fire is essential for the regeneration of some species. Further experimentation should evaluate these findings and explore if harvesting and intervention, such as sowing of fire-cued seeds, allow sustainable, localised harvesting of spinifex grasslands.

Willingness-to-pay for infrastructure investments for alternative fuel vehicles

This study investigates potential demand for infrastructure investment for alternative fuel vehicles by applying stated preference methods to a Japanese sample. The potential demand is estimated on the basis of how much people are willing to pay for alternative fuel vehicles under various refueling scenarios. Using the estimated parameters, the economic efficiency of establishing battery-exchange stations for electric vehicles is examined. The results indicate that infrastructural development of battery-exchange stations can be efficient when electric vehicle sales exceed 5.63% of all new vehicle sales. Further, we find a complementary relationship between the cruising ranges of alternative fuel vehicles and the infrastructure established.

An alternative theory of legacy information systems

Organisational dependence upon IT continues to grow yet experiences of satisfaction vary widely. Problematic, aged IT is often cited as being a fundamental problem in this respect and this is commonly termed legacy information systems. However, in this paper the author offers an alternative, and arguably more comprehensive, theory of legacy information systems that accommodates multiple viewpoints and recognises its inherent dynamism. The paper suggests a theory of legacy information systems that comprises of the concepts of temporal effects, interpretations and characteristics. It is argued that legacy information systems are constructed of many ‘legacies’ that are handed down continuously, forming an amorphous set of sociotechnical interdependencies and relationships.

Best of breed IT strategy: an alternative to enterprise resource planning systems

Abstract - Enterprise Resource Planning (ERP) software has become the dominant strategic platform for supporting enterprise-wide business processes. However, single vendor ERP software systems have been criticised for not meeting specific organisation and industry requirements. An alternative approach ‘Best of Breed (BoB)’, integrates components of software from multiple standard package vendors, and in some cases custom components. The objective is to develop enterprise systems that are more closely aligned with the requirements of an organisation. Although this approach may not be common at present it is likely to grow in importance due to business needs and technology advances such as the componentisation of ERP software. A case study analysis of a BoB implementation at a global entertainment's company is used as a platform for the discussion of the issues associated with this strategy and a comparison is made with the single vendor ERP alternative. The analysis centres on the complexity of implementation, the differences in the levels of functionality and business fit and the maintenance requirements.

Bayesian hierarchical models for analysing spatial point-based data at a grid level: A comparison of approaches

Spatial data are now prevalent in a wide range of fields including environmental and health science. This has led to the development of a range of approaches for analysing patterns in these data. In this paper, we compare several Bayesian hierarchical models for analysing point-based data based on the discretization of the study region, resulting in grid-based spatial data. The approaches considered include two parametric models and a semiparametric model. We highlight the methodology and computation for each approach. Two simulation studies are undertaken to compare the performance of these models for various structures of simulated point-based data which resemble environmental data. A case study of a real dataset is also conducted to demonstrate a practical application of the modelling approaches. Goodness-of-fit statistics are computed to compare estimates of the intensity functions. The deviance information criterion is also considered as an alternative model evaluation criterion. The results suggest that the adaptive Gaussian Markov random field model performs well for highly sparse point-based data where there are large variations or clustering across the space; whereas the discretized log Gaussian Cox process produces good fit in dense and clustered point-based data. One should generally consider the nature and structure of the point-based data in order to choose the appropriate method in modelling a discretized spatial point-based data.