HVAC system size – getting it right

There is evidence that many heating, ventilating & air conditioning (HVAC) systems, installed in larger buildings, have more capacity than is ever required to keep the occupants comfortable. This paper explores the reasons why this can occur, by examining a typical brief/design/documentation process. Over-sized HVAC systems cost more to install and operate and may not be able to control thermal comfort as well as a “right-sized” system. These impacts are evaluated, where data exists. Finally, some suggestions are developed to minimise both the extent of, and the negative impacts of, HVAC system over-sizing, for example: • Challenge “rules of thumb” and/or brief requirements which may be out of date. • Conduct an accurate load estimate, using AIRAH design data, specific to project location, and then resist the temptation to apply “safety factors • Use a load estimation program that accounts for thermal storage and diversification of peak loads for each zone and air handling system. • Select chiller sizes and staged or variable speed pumps and fans to ensure good part load performance. • Allow for unknown future tenancies by designing flexibility into the system, not by over-sizing. For example, generous sizing of distribution pipework and ductwork will allow available capacity to be redistributed. • Provide an auxiliary tenant condenser water loop to handle high load areas. • Consider using an Integrated Design Process, build an integrated load and energy use simulation model and test different operational scenarios • Use comprehensive Life Cycle Cost analysis for selection of the most optimal design solutions. This paper is an interim report on the findings of CRC-CI project 2002-051-B, Right-Sizing HVAC Systems, which is due for completion in January 2006.

Issues and concerns of microscopic calibration process at different network levels : case study of Pacific Motorway

Calibration process in micro-simulation is an extremely complicated phenomenon. The difficulties are more prevalent if the process encompasses fitting aggregate and disaggregate parameters e.g. travel time and headway. The current practice in calibration is more at aggregate level, for example travel time comparison. Such practices are popular to assess network performance. Though these applications are significant there is another stream of micro-simulated calibration, at disaggregate level. This study will focus on such microcalibration exercise-key to better comprehend motorway traffic risk level, management of variable speed limit (VSL) and ramp metering (RM) techniques. Selected section of Pacific Motorway in Brisbane will be used as a case study. The discussion will primarily incorporate the critical issues encountered during parameter adjustment exercise (e.g. vehicular, driving behaviour) with reference to key traffic performance indicators like speed, lane distribution and headway; at specific motorway points. The endeavour is to highlight the utility and implications of such disaggregate level simulation for improved traffic prediction studies. The aspects of calibrating for points in comparison to that for whole of the network will also be briefly addressed to examine the critical issues such as the suitability of local calibration at global scale. The paper will be of interest to transport professionals in Australia/New Zealand where micro-simulation in particular at point level, is still comparatively a less explored territory in motorway management.

Issues and concerns of microscopic calibration process at different network levels : case study of pacific motorway

Calibration process in micro-simulation is an extremely complicated phenomenon. The difficulties are more prevalent if the process encompasses fitting aggregate and disaggregate parameters e.g. travel time and headway. The current practice in calibration is more at aggregate level, for example travel time comparison. Such practices are popular to assess network performance. Though these applications are significant there is another stream of micro-simulated calibration, at disaggregate level. This study will focus on such micro-calibration exercise-key to better comprehend motorway traffic risk level, management of variable speed limit (VSL) and ramp metering (RM) techniques. Selected section of Pacific Motorway in Brisbane will be used as a case study. The discussion will primarily incorporate the critical issues encountered during parameter adjustment exercise (e.g. vehicular, driving behaviour) with reference to key traffic performance indicators like speed, land distribution and headway; at specific motorway points. The endeavour is to highlight the utility and implications of such disaggregate level simulation for improved traffic prediction studies. The aspects of calibrating for points in comparison to that for whole of the network will also be briefly addressed to examine the critical issues such as the suitability of local calibration at global scale. The paper will be of interest to transport professionals in Australia/New Zealand where micro-simulation in particular at point level, is still comparatively a less explored territory in motorway management.

The velocity synchronous discrete Fourier transform for order tracking in the field of rotating machinery

Diagnostics of rotating machinery has developed significantly in the last decades, and industrial applications are spreading in different sectors. Most applications are characterized by varying velocities of the shaft and in many cases transients are the most critical to monitor. In these variable speed conditions, fault symptoms are clearer in the angular/order domains than in the common time/frequency ones. In the past, this issue was often solved by synchronously sampling data by means of phase locked circuits governing the acquisition; however, thanks to the spread of cheap and powerful microprocessors, this procedure is nowadays rarer; sampling is usually performed at constant time intervals, and the conversion to the order domain is made by means of digital signal processing techniques. In the last decades different algorithms have been proposed for the extraction of an order spectrum from a signal sampled asynchronously with respect to the shaft rotational velocity; many of them (the so called computed order tracking family) use interpolation techniques to resample the signal at constant angular increments, followed by a common discrete Fourier transform to shift from the angular domain to the order domain. A less exploited family of techniques shifts directly from the time domain to the order spectrum, by means of modified Fourier transforms. This paper proposes a new transform, named velocity synchronous discrete Fourier transform, which takes advantage of the instantaneous velocity to improve the quality of its result, reaching performances that can challenge the computed order tracking.

Diagnostic of Rolling Element Bearings with Envelope Analysis in Non-Stationary Conditions

In the field of rolling element bearing diagnostics, envelope analysis has gained in the last years a leading role among the different digital signal processing techniques. The original constraint of constant operating speed has been relaxed thanks to the combination of this technique with the computed order tracking, able to resample signals at constant angular increments. In this way, the field of application of this technique has been extended to cases in which small speed fluctuations occur, maintaining high effectiveness and efficiency. In order to make this algorithm suitable to all industrial applications, the constraint on speed has to be removed completely. In fact, in many applications, the coincidence of high bearing loads, and therefore high diagnostic capability, with acceleration-deceleration phases represents a further incentive in this direction. This chapter presents a procedure for the application of envelope analysis to speed transients. The effect of load variation on the proposed technique will be also qualitatively addressed.

Drivers' ability to absorb information from co-located signs along motorways

The paper presents initial findings from an Austroads funded project NT1782 Ability to Absorb Information through Electronic and Static Signs. The paper aims to investigate how easily messages displayed on co-located signs can be absorbed, and if drivers can absorb messages and take appropriate action without any adverse impact on the safety and efficiency of driving. Co-location of three types of signs under motorway conditions was investigated: direction signs (DS), variable message signs (VMS) and variable speed limits/lane control signs (VSL/LCS). The authors reviewed global wide practices and research evidence on different types of sign co-locations. It was found that dual co-location of VSL/LCS, VMS and/or DS is a practical arrangement which has been widely practised overseas and in Australia. Triple co-location of VSL/LCS, VMS and DS is also practised overseas but is still new to the Australian driving community. The NT1782 project also employed an advanced driving simulator (ADS) to further investigate the possible impacts of sign co-location on drivers’ responses in an emergency situation and there were no obviously adverse impacts have been identified from the ADS study. The authors consolidated all findings and concluded that although there is no clear evidence showing that triple co-location gives rise to riskier behaviour, this proposition should be viewed with caution. Further evaluation of triple co-location in a real-life setting is called for.

How do other people influence your driving speed? Exploring the 'who' and the 'how' of social influences on speeding from a qualitative perspective

Using only legal sanctions to manage the speed at which people drive ignores the potential benefits of harnessing social factors such as the influence of others. Social influences on driver speeds were explored in this qualitative examination of 67 Australian drivers. Focus group interviews with 8 driver types (young, mid-age and older males and females, and self-identified Excessive and Rare speeders) were guided by Akers’ social learning theory (Akers, 1998). Findings revealed two types of influential others: people known to the driver (passengers and parents), and unknown other drivers. Passengers were generally described as having a slowing influence on drivers: responsibility for the safety of people in the car and consideration for passenger comfort were key themes. In contrast, all but the Rare speeders reported increasing their speed when driving alone. Parental role modelling was also described. In relation to other drivers, key themes included speeding to keep up with traffic flow and perceived pressure to drive faster. This ‘pressure’ from others to ‘speed up’ was expressed in all groups and reported strategies for managing this varied. Encouragingly, examples of actual or anticipated social rewards for speeding were less common than examples of social punishments. Three main themes relating to social punishments were embarrassment, breaching the trust of others, and presenting an image of a responsible driver. Impression management and self-presentation are discussed in light of these findings. Overall, our findings indicate scope to exploit the use of social sanctions for speeding and social praise for speed limit compliance to enhance speed management strategies.

Analysis of road potential and bottlenecks based on operating speed

Vehicle detectors have been installed at approximately every 300 meters on each lane on Tokyo metropolitan expressway. Various traffic data such as traffic volume, average speed and time occupancy are collected by vehicle detectors. We can understand traffic characteristics of every point by comparing traffic data collected at consecutive points. In this study, we focused on average speed, analyzed road potential by operating speed during free-flow conditions, and identified latent bottlenecks. Furthermore, we analyzed effects for road potential by the rainfall level and day of the week. It’s expected that this method of analysis will be utilized for installation of ITS such as drive assist, estimation of parameters for traffic simulation and feedback to road design as congestion measures.

System identification and control of an aerobot drive system

Fast thrust changes are important for authoritive control of VTOL micro air vehicles. Fixed-pitch rotors that alter thrust by varying rotor speed require high-bandwidth control systems to provide adequate performace. We develop a feedback compensator for a brushless hobby motor driving a custom rotor suitable for UAVs. The system plant is identified using step excitation experiments. The aerodynamic operating conditions of these rotors are unusual and so experiments are performed to characterise expected load disturbances. The plant and load models lead to a proportional controller design capable of significantly decreasing rise-time and propagation of disturbances, subject to bus voltage constraints.

Driving speed is altered by monocular Neutral Density filters : the Enright phenomenon

Introduction: An observer, looking sideways from a moving vehicle, while wearing a neutral density filter over one eye, can have a distorted perception of speed, known as the Enright phenomenon. The purpose of this study was to determine how the Enright phenomenon influences driving behaviour. Methods: A geometric model of the Enright phenomenon was developed. Ten young, visually normal, participants (mean age = 25.4 years) were tested on a straight section of a closed driving circuit and instructed to look out of the right side of the vehicle and drive at either 40 Km/h or 60 Km/h under the following binocular viewing conditions: with a 0.9 ND filter over the left eye (leading eye); 0.9 ND filter over the right eye (trailing eye); 0.9 ND filters over both eyes, and with no filters over either eye. The order of filter conditions was randomised and the speed driven recorded for each condition. Results: Speed judgments did not differ significantly between the two baseline conditions (no filters and both eyes filtered) for either speed tested. For the baseline conditions, when subjects were asked to drive at 60 Km/h they matched this speed well (61 ± 10.2 Km/h) but drove significantly faster than requested (51.6 ± 9.4 Km/h) when asked to drive at 40 Km/h. Subjects significantly exceeded baseline speeds by 8.7± 5.0 Km/h, when the trailing eye was filtered and travelled slower than baseline speeds by 3.7± 4.6 Km/h when the leading eye was filtered. Conclusions: This is the first quantitative study demonstrating how the Enright effect can influence perceptions of driving speed, and demonstrates that monocular filtering of an eye can significantly impact driving speeds, albeit to a lesser extent than predicted by geometric models of the phenomenon.

A review of the effectiveness of speed control measures in roadwork zones

Noncompliance with speed limits is one of the major safety concerns in roadwork zones. Although numerous studies have attempted to evaluate the effectiveness of safety measures on speed limit compliance, many report inconsistent findings. This paper aims to review the effectiveness of four categories of roadwork zone speed control measures: Informational, Physical, Enforcement, and Educational measures. While informational measures (static signage, variable message signage) evidently have small to moderate effects on speed reduction, physical measures (rumble strips, optical speed bars) are found ineffective for transient and moving work zones. Enforcement measures (speed camera, police presence) have the greatest effects, while educational measures also have significant potential to improve public awareness of roadworker safety and to encourage slower speeds in work zones. Inadequate public understanding of roadwork risks and hazards, failure to notice signs, and poor appreciation of safety measures are the major causes of noncompliance with speed limits.

The relationship between drivers’ perceptions toward police speed enforcement and self-reported speeding behaviour

Exceeding the speed limit and driving too fast for the conditions are regularly cited as significant contributing factors in traffic crashes, particularly fatal and serious injury crashes. Despite an extensive body of research highlighting the relationship between increased vehicle speeds and crash risk and severity, speeding remains a pervasive behaviour on Australian roads. The development of effective countermeasures designed to reduce the prevalence of speeding behaviour requires that this behaviour is well understood. The primary aim of this program of research was to develop a better understanding of the influence of drivers’ perceptions and attitudes toward police speed enforcement on speeding behaviour. Study 1 employed focus group discussions with 39 licensed drivers to explore the influence of perceptions relating to specific characteristics of speed enforcement policies and practices on drivers’ attitudes towards speed enforcement. Three primary factors were identified as being most influential: site selection; visibility; and automaticity (i.e., whether the enforcement approach is automated/camera-based or manually operated). Perceptions regarding these enforcement characteristics were found to influence attitudes regarding the perceived legitimacy and transparency of speed enforcement. Moreover, misperceptions regarding speed enforcement policies and practices appeared to also have a substantial impact on attitudes toward speed enforcement, typically in a negative direction. These findings have important implications for road safety given that prior research has suggested that the effectiveness of speed enforcement approaches may be reduced if efforts are perceived by drivers as being illegitimate, such that they do little to encourage voluntary compliance. Study 1 also examined the impact of speed enforcement approaches varying in the degree of visibility and automaticity on self-reported willingness to comply with speed limits. These discussions suggested that all of the examined speed enforcement approaches (see Section 1.5 for more details) generally showed potential to reduce vehicle speeds and encourage compliance with posted speed limits. Nonetheless, participant responses suggested a greater willingness to comply with approaches operated in a highly visible manner, irrespective of the corresponding level of automaticity of the approach. While less visible approaches were typically associated with poorer rates of driver acceptance (e.g., perceived as “sneaky” and “unfair”), participants reported that such approaches would likely encourage long-term and network-wide impacts on their own speeding behaviour, as a function of the increased unpredictability of operations and increased direct (specific deterrence) and vicarious (general deterrence) experiences with punishment. Participants in Study 1 suggested that automated approaches, particularly when operated in a highly visible manner, do little to encourage compliance with speed limits except in the immediate vicinity of the enforcement location. While speed cameras have been criticised on such grounds in the past, such approaches can still have substantial road safety benefits if implemented in high-risk settings. Moreover, site-learning effects associated with automated approaches can also be argued to be a beneficial by-product of enforcement, such that behavioural modifications are achieved even in the absence of actual enforcement. Conversely, manually operated approaches were reported to be associated with more network-wide impacts on behaviour. In addition, the reported acceptance of such methods was high, due to the increased swiftness of punishment, ability for additional illegal driving behaviours to be policed and the salutary influence associated with increased face-to-face contact with authority. Study 2 involved a quantitative survey conducted with 718 licensed Queensland drivers from metropolitan and regional areas. The survey sought to further examine the influence of the visibility and automaticity of operations on self-reported likelihood and duration of compliance. Overall, the results from Study 2 corroborated those of Study 1. All examined approaches were again found to encourage compliance with speed limits, such that all approaches could be considered to be “effective”. Nonetheless, significantly greater self-reported likelihood and duration of compliance was associated with visibly operated approaches, irrespective of the corresponding automaticity of the approach. In addition, the impact of automaticity was influenced by visibility; such that significantly greater self-reported likelihood of compliance was associated with manually operated approaches, but only when they are operated in a less visible fashion. Conversely, manually operated approaches were associated with significantly greater durations of self-reported compliance, but only when they are operated in a highly visible manner. Taken together, the findings from Studies 1 and 2 suggest that enforcement efforts, irrespective of their visibility or automaticity, generally encourage compliance with speed limits. However, the duration of these effects on behaviour upon removal of the enforcement efforts remains questionable and represents an area where current speed enforcement practices could possibly be improved. Overall, it appears that identifying the optimal mix of enforcement operations, implementing them at a sufficient intensity and increasing the unpredictability of enforcement efforts (e.g., greater use of less visible approaches, random scheduling) are critical elements of success. Hierarchical multiple regression analyses were also performed in Study 2 to investigate the punishment-related and attitudinal constructs that influence self-reported frequency of speeding behaviour. The research was based on the theoretical framework of expanded deterrence theory, augmented with three particular attitudinal constructs. Specifically, previous research examining the influence of attitudes on speeding behaviour has typically focussed on attitudes toward speeding behaviour in general only. This research sought to more comprehensively explore the influence of attitudes by also individually measuring and analysing attitudes toward speed enforcement and attitudes toward the appropriateness of speed limits on speeding behaviour. Consistent with previous research, a number of classical and expanded deterrence theory variables were found to significantly predict self-reported frequency of speeding behaviour. Significantly greater speeding behaviour was typically reported by those participants who perceived punishment associated with speeding to be less certain, who reported more frequent use of punishment avoidance strategies and who reported greater direct experiences with punishment. A number of interesting differences in the significant predictors among males and females, as well as younger and older drivers, were reported. Specifically, classical deterrence theory variables appeared most influential on the speeding behaviour of males and younger drivers, while expanded deterrence theory constructs appeared more influential for females. These findings have important implications for the development and implementation of speeding countermeasures. Of the attitudinal factors, significantly greater self-reported frequency of speeding behaviour was reported among participants who held more favourable attitudes toward speeding and who perceived speed limits to be set inappropriately low. Disappointingly, attitudes toward speed enforcement were found to have little influence on reported speeding behaviour, over and above the other deterrence theory and attitudinal constructs. Indeed, the relationship between attitudes toward speed enforcement and self-reported speeding behaviour was completely accounted for by attitudes toward speeding. Nonetheless, the complexity of attitudes toward speed enforcement are not yet fully understood and future research should more comprehensively explore the measurement of this construct. Finally, given the wealth of evidence (both in general and emerging from this program of research) highlighting the association between punishment avoidance and speeding behaviour, Study 2 also sought to investigate the factors that influence the self-reported propensity to use punishment avoidance strategies. A standard multiple regression analysis was conducted for exploratory purposes only. The results revealed that punishment-related and attitudinal factors significantly predicted approximately one fifth of the variance in the dependent variable. The perceived ability to avoid punishment, vicarious punishment experience, vicarious punishment avoidance and attitudes toward speeding were all significant predictors. Future research should examine these relationships more thoroughly and identify additional influential factors. In summary, the current program of research has a number of implications for road safety and speed enforcement policy and practice decision-making. The research highlights a number of potential avenues for the improvement of public education regarding enforcement efforts and provides a number of insights into punishment avoidance behaviours. In addition, the research adds strength to the argument that enforcement approaches should not only demonstrate effectiveness in achieving key road safety objectives, such as reduced vehicle speeds and associated crashes, but also strive to be transparent and legitimate, such that voluntary compliance is encouraged. A number of potential strategies are discussed (e.g., point-to-point speed cameras, intelligent speed adaptation. The correct mix and intensity of enforcement approaches appears critical for achieving optimum effectiveness from enforcement efforts, as well as enhancements in the unpredictability of operations and swiftness of punishment. Achievement of these goals should increase both the general and specific deterrent effects associated with enforcement through an increased perceived risk of detection and a more balanced exposure to punishment and punishment avoidance experiences.

Effects of speeding and headway related variable message signs on driver behaviour and attitudes

This research project examined objective measures of driver behaviour and road users' perceptions on the usefulness and effectiveness of three specific VMS (Variable Message Signs) interventions to improve speeding and headway behaviours. The interventions addressed speeding behaviour alone (intervention 1), headway behaviour alone (intervention 2) and a combination of speeding and headway behaviour (intervention 3). Six VMS were installed along a segment of the Bruce Highway, with a series of three signs for each of the northbound and southbound traffic. Speeds and headway distances were measured with loop detectors installed before and after each VMS. Messages addressing speeding and headway were devised for display on the VMS. A driver could receive a message if they were detected as exceeding the posted speed limit (of 90km/hr) or if the distance to the vehicle in front was less than 2.0s. In addition to the on-road objective measurement of speeding and headway behaviours, the research project elicited self-reported responses to the speeding and headway messages from a sample of drivers via a community-based survey. The survey sought to examine the drivers' beliefs about the effectiveness of the signs and messages, and their views about the role, use, and effectiveness of VMS more generally.