Test and evaluation system for multi-protocol sampled value protection schemes

Proposed transmission smart grids will use a digital platform for the automation of substations operating at voltage levels of 110 kV and above. The IEC 61850 series of standards, released in parts over the last ten years, provide a specification for substation communications networks and systems. These standards, along with IEEE Std 1588-2008 Precision Time Protocol version 2 (PTPv2) for precision timing, are recommended by the both IEC Smart Grid Strategy Group and the NIST Framework and Roadmap for Smart Grid Interoperability Standards for substation automation. IEC 61850-8-1 and IEC 61850-9-2 provide an inter-operable solution to support multi-vendor digital process bus solutions, allowing for the removal of potentially lethal voltages and damaging currents from substation control rooms, a reduction in the amount of cabling required in substations, and facilitates the adoption of non-conventional instrument transformers (NCITs). IEC 61850, PTPv2 and Ethernet are three complementary protocol families that together define the future of sampled value digital process connections for smart substation automation. This paper describes a specific test and evaluation system that uses real time simulation, protection relays, PTPv2 time clocks and artificial network impairment that is being used to investigate technical impediments to the adoption of SV process bus systems by transmission utilities. Knowing the limits of a digital process bus, especially when sampled values and NCITs are included, will enable utilities to make informed decisions regarding the adoption of this technology.

Injuries across adolescence : an investigation using the Extended Adolescent Injury Checklist (E-AIC)

Injury is the leading cause of death among adolescents, and in many countries, accounts for more deaths than all other causes combined. Rates of death due to injury also increase dramatically across adolescence. The Australian Institute of Health and Welfare reported that, in 2005, there were 954 deaths of young Australians due to injury, which is a rate of 26 deaths per 100,000 young people. Of these deaths, 4% were adolescents aged 12-14, 17% were aged 15-17, and 80% were aged 18-24 years. Issues addressed: Injuries are the leading cause of death among adolescents. The current research examined a measure of adolescent injury in terms of whether it encompasses the diverse injury experiences of Australian adolescents, including high-risk and normative adolescents, and thus determine its utility as a tool for health promotion research. Grade 9 students from two Brisbane high schools (n=202, aged 13-14 years) and adolescents recruited from the Emergency Department waiting rooms of four Brisbane hospitals (n=98, aged 16-18 years) completed the Extended Adolescent Injury Checklist (E-AIC). The most common cause of injury among adolescents was a sports activity, followed by fights for all participants except schoolbased males, who experienced more bicycle injuries. Alcohol use was most frequently reported in association with interpersonal violence injuries. A broad variety of injuries, occurring in context of multiple risk as well as normative behaviours, were reported by adolescents in both school and ED settings, and were captured by the E-AIC. Findings suggest that the E-AIC is a useful measure that captures the injury experiences of adolescents in different contexts. The high occurrence of injuries that do not result in formal medical treatment also indicates scope for interventions to be based around lessons in first aid, while also incorporating injury prevention components.

Reality bytes : technology in real world legal education

The use of technology for purposes such as communication and document management has become essential to legal practice with practitioners and courts increasingly relying on various forms of technology. Accordingly, legal practitioners need to be able to understand, communicate with, and persuade their audience using this technology. Technology skills are therefore an essential and integral part of undergraduate legal education, and given the widening participation agenda in Australia and consequent increasing diversity of law students, it must also be available to all students. To neglect this most crucial part of modern legal education is to fail in a fundamental aspect of a University’s obligation not just to its students, but ultimately to our students’ potential employers and their future clients. This paper will consider how law schools can facilitate the development of technology skills by using technology to facilitate mooting in settings that replicate legal practice. In order to assess the facilities at the disposal of universities, the authors surveyed the law schools in Australia about their equipment in and use of electronic moot court rooms. The authors also conducted and evaluated an internal mooting competition using Elluminate, an online communication platform available to students through Blackboard. Students were able to participate wherever they were located without the need to attend a moot court room. The results of the survey and evaluation of the Elluminate competition will be discussed. The paper will conclude that while it is essential to teach technology skills as part of legal education, it is important that the benefits and importance of using technology be made clear in order for it to be accepted and embraced by the students. Technology must also be available to all students considering the widening participation in higher education and consequent increasing diversity of law students.

Spatial/surveying programs repositioning within new STEM Faculty at QUT

Many of the undergraduate and postgraduate programs of the former Faculty of Built Environment and Engineering PLUS Faculty of Sciences and Technology are changing as a result of merging these two large organisations, with some disciplines relocating to faculties of Creative Industries and Health respectively. The new STEM precinct under construction has begun rising from the proverbial hole-in-the-ground. Existing Surveying and Spatial Sciences programs, assets and staff are being repositioned with the newly formed School of Earth, Environment and Biological Sciences.2011. Golden graduates morning tea organised by QUT Alumni. Technology upgrades to the Mapping Sciences lab benefits 3-D learning experiences. Second and third-year students are undertaking Work Integrated Learning (WIL) over the summer vacation period. Final year students recently presented capstone project presentations at mini-conference in the Gibson Rooms overlooking a vibrant Southbank and sparkling Brisbane River. Discussion on end of year graduation ceremony held at QPAC.

Room ventilation and the risk of airborne infection transmission in three health care settings within a large teaching hospital

Background: Room ventilation is a key determinant of airborne disease transmission. Despite this, ventilation guidelines in hospitals are not founded on robust scientific evidence related to prevention of airborne transmission. Methods: We sought to assess the effect of ventilation rates on influenza, tuberculosis (TB) and rhinovirus infection risk within three distinct rooms in a major urban hospital; a Lung Function Laboratory, Emergency Department (ED) Negative-pressure Isolation Room and an Outpatient Consultation Room were investigated. Air exchange rate measurements were performed in each room using CO2 as a tracer. Gammaitoni and Nucci’s model was employed to estimate infection risk. Results: Current outdoor air exchange rates in the Lung Function Laboratory and ED Isolation Room limited infection risks to between 0.1 and 3.6%. Influenza risk for individuals entering an Outpatient Consultation Room after an infectious individual departed ranged from 3.6 to 20.7%, depending on the duration for which each person occupied the room. Conclusions: Given the absence of definitive ventilation guidelines for hospitals, air exchange measurements combined with modelling afford a useful means of assessing, on a case-by-case basis, the suitability of room ventilation at preventing airborne disease transmission.

O'Neill Building Nudgee College

This project involved the complete refurbishment and extension of a 1980’s two-storey domestic brick building, previously used as a Boarding House (Class 3), into Middle School facilities (Class 9b) on a heritage listed site at Nudgee College secondary school, Brisbane. The building now accommodates 12 technologically advanced classrooms, computer lab and learning support rooms, tuckshop, art room, mini library/reading/stage area, dedicated work areas for science and large projects with access to water on both floors, staff facilities and an undercover play area suitable for assemblies and presentations. The project was based on a Reggio Emilia approach, in which the organisation of the physical environment is referred to as the child’s third teacher, creating opportunities for complex, varied, sustained and changing relationships between people and ideas. Classrooms open to a communal centre piazza and are integrated with the rest of the school and the school with the surrounding community. In order to achieve this linkage of the building with the overall masterplan of the site, a key strategy of the internal planning was to orientate teaching areas around a well defined active circulation space that breaks out of the building form to legibly define the new access points to the building and connect up to the pathway network of the campus. The width of the building allowed for classrooms and a generous corridor that has become ‘breakout’ teaching areas for art, IT, and small group activities. Large sliding glass walls allow teachers to maintain supervision of students across all areas and allow maximum light penetration through small domestic window openings into the deep and low-height spaces. The building was also designed with an effort to uphold cultural characteristics from the Edmund Rice Education Charter (2004). Coherent planning is accompanied by a quality fit-out, creating a vibrant and memorable environment in which to deliver the upper primary curriculum. Consistent with the Reggio Emilia approach, materials, expressive of the school’s colours, are used in a contemporary, adventurous manner to create panels of colour useful for massing and defining the ‘breakout’ teaching areas and paths of travel, and storage elements are detailed and arranged to draw attention to their aesthetic features. Modifications were difficult due to the random placement of load bearing walls, minimum ceiling heights, the general standard of finishes and new fire and energy requirements, however the reuse of this building was assessed to be up to 30% cheaper than an equivalent new building, The fit out integrates information technology and services at a level not usually found in primary school facilities. This has been achieved within the existing building fabric through thoughtful detailing and co-ordination with allied disciplines.

Opinions, attitudes and driving experiences of car and racing "enthusiasts" : results of the Ontario Car and Racing Club Survey

In recent years, car club and racing websites and forums have become an increasingly popular way for car enthusiasts to access racing and car club news, chat-rooms and message boards. However, no North American research has been found that has examined opinions and driving experiences of car and racing enthusiasts. The purpose of this study was to examine car club members’ opinions about and experiences with various aspects of driving, road safety and traffic legislation, with a particular focus on street racing. A web-based questionnaire (Survey Monkey) was developed using the expert panel method and was primarily based on validated instruments or questions that were developed from other surveys. The questionnaire included: 1) driver concerns regarding traffic safety issues and legislation; 2) attitudes regarding various driving activities; 3) leisure-time activities, including club activities; 4) driving experiences, including offences and collisions; and 5) socio-demographic questions. The survey was pre- tested and piloted. Electronic information letters were sent out to an identified list of car clubs and forums situated in southern Ontario. Car club participants were invited to fill out the questionnaire. This survey found that members of car clubs share similar concerns regarding various road safety issues with samples of Canadian drivers, although a smaller percentage of car club members are concerned about speeding-related driving. Car club members had varied opinions regarding Ontario’s Street Racers, Stunt and Aggressive Drivers Legislation. The respondents agreed the most with the new offences regarding not sitting in the driver’s seat, having a person in the trunk, or driving as close as possible to another vehicle, pedestrian or object on or near the highway without a reason. The majority disagreed with police powers of impoundment and on-the-spot licence suspensions. About three quarters of respondents reported no collisions or police stops for traffic offences in the past five years. Of those who had been stopped, the most common offence was reported as speeding. This study is the first in Canada to examine car club members’ opinions about and experiences with various aspects of driving, road safety and traffic legislation. Given the ubiquity of car clubs and fora in Canada, insights on members’ opinions and practices provide important information to road safety researchers.

Falling through the web : implications for internet introverts

Is the brain evolving and adapting to new technological environments such as that of Silicon Valley? This paper examines changes that are being observed and studied relating to a possible correlation between ‘excessive’ focus on technology and the emergence of diagnosable social, physical and mental health dysfunction. The author explores the possible role of university staff and student services in the duty of care toward students. Would it not be more ethical to provide education on healthy technology use and to provide evidence based therapy for those students who fall through the web? Currently students end up being excluded from their courses. Many suffer from social anxiety and depression and lack confidence and social skills to find or hold down a job. Currently many “hibernate” in their rooms for months or years frequently in a state of despair.

Evaluation of the cost-effectiveness of strategies claiming to reduce the risk of surgical site infections following primary total hip arthroplasty

Background Total hip arthroplasty (THA) is a commonly performed procedure and numbers are increasing with ageing populations. One of the most serious complications in THA are surgical site infections (SSIs), caused by pathogens entering the wound during the procedure. SSIs are associated with a substantial burden for health services, increased mortality and reduced functional outcomes in patients. Numerous approaches to preventing these infections exist but there is no gold standard in practice and the cost-effectiveness of alternate strategies is largely unknown. Objectives The aim of this project was to evaluate the cost-effectiveness of strategies claiming to reduce deep surgical site infections following total hip arthroplasty in Australia. The objectives were: 1. Identification of competing strategies or combinations of strategies that are clinically relevant to the control of SSI related to hip arthroplasty 2. Evidence synthesis and pooling of results to assess the volume and quality of evidence claiming to reduce the risk of SSI following total hip arthroplasty 3. Construction of an economic decision model incorporating cost and health outcomes for each of the identified strategies 4. Quantification of the effect of uncertainty in the model 5. Assessment of the value of perfect information among model parameters to inform future data collection Methods The literature relating to SSI in THA was reviewed, in particular to establish definitions of these concepts, understand mechanisms of aetiology and microbiology, risk factors, diagnosis and consequences as well as to give an overview of existing infection prevention measures. Published economic evaluations on this topic were also reviewed and limitations for Australian decision-makers identified. A Markov state-transition model was developed for the Australian context and subsequently validated by clinicians. The model was designed to capture key events related to deep SSI occurring within the first 12 months following primary THA. Relevant infection prevention measures were selected by reviewing clinical guideline recommendations combined with expert elicitation. Strategies selected for evaluation were the routine use of pre-operative antibiotic prophylaxis (AP) versus no use of antibiotic prophylaxis (No AP) or in combination with antibiotic-impregnated cement (AP & ABC) or laminar air operating rooms (AP & LOR). The best available evidence for clinical effect size and utility parameters was harvested from the medical literature using reproducible methods. Queensland hospital data were extracted to inform patients’ transitions between model health states and related costs captured in assigned treatment codes. Costs related to infection prevention were derived from reliable hospital records and expert opinion. Uncertainty of model input parameters was explored in probabilistic sensitivity analyses and scenario analyses and the value of perfect information was estimated. Results The cost-effectiveness analysis was performed from a health services perspective using a hypothetical cohort of 30,000 THA patients aged 65 years. The baseline rate of deep SSI was 0.96% within one year of a primary THA. The routine use of antibiotic prophylaxis (AP) was highly cost-effective and resulted in cost savings of over $1.6m whilst generating an extra 163 QALYs (without consideration of uncertainty). Deterministic and probabilistic analysis (considering uncertainty) identified antibiotic prophylaxis combined with antibiotic-impregnated cement (AP & ABC) to be the most cost-effective strategy. Using AP & ABC generated the highest net monetary benefit (NMB) and an incremental $3.1m NMB compared to only using antibiotic prophylaxis. There was a very low error probability that this strategy might not have the largest NMB (<5%). Not using antibiotic prophylaxis (No AP) or using both antibiotic prophylaxis combined with laminar air operating rooms (AP & LOR) resulted in worse health outcomes and higher costs. Sensitivity analyses showed that the model was sensitive to the initial cohort starting age and the additional costs of ABC but the best strategy did not change, even for extreme values. The cost-effectiveness improved for a higher proportion of cemented primary THAs and higher baseline rates of deep SSI. The value of perfect information indicated that no additional research is required to support the model conclusions. Conclusions Preventing deep SSI with antibiotic prophylaxis and antibiotic-impregnated cement has shown to improve health outcomes among hospitalised patients, save lives and enhance resource allocation. By implementing a more beneficial infection control strategy, scarce health care resources can be used more efficiently to the benefit of all members of society. The results of this project provide Australian policy makers with key information about how to efficiently manage risks of infection in THA.

Performance analysis of IEC 61850 sampled value process bus networks

Process bus networks are the next stage in the evolution of substation design, bringing digital technology to the high voltage switchyard. Benefits of process buses include facilitating the use of Non-Conventional Instrument Transformers, improved disturbance recording and phasor measurement and the removal of costly, and potentially hazardous, copper cabling from substation switchyards and control rooms. This paper examines the role a process bus plays in an IEC 61850 based Substation Automation System. Measurements taken from a process bus substation are used to develop an understanding of the network characteristics of "whole of substation" process buses. The concept of "coherent transmission" is presented and the impact of this on Ethernet switches is examined. Experiments based on substation observations are used to investigate in detail the behavior of Ethernet switches with sampled value traffic. Test methods that can be used to assess the adequacy of a network are proposed, and examples of the application and interpretation of these tests are provided. Once sampled value frames are queued by an Ethernet switch the additional delay incurred by subsequent switches is minimal, and this allows their use in switchyards to further reduce communications cabling, without significantly impacting operation. The performance and reliability of a process bus network operating with close to the theoretical maximum number of digital sampling units (merging units or electronic instrument transformers) was investigated with networking equipment from several vendors, and has been demonstrated to be acceptable.

What information-related activities do people with ESKD use?

Background Information practice is an emerging area of research that seeks to reveal how people learn to connect with the complex multimodal information landscapes that informs their ability to make decisions. Previous research has identified that people with end stage kidney disease (ESKD) tend to adopt a ‘received’ or ‘engaged’ view of information but little is known about the activities of information practice. Objectives This research project sought to identify the: i) information-related activities; and ii) how information is used. Methods Using a constructivist qualitative methodology, ten people with ESKD living in a large metropolitan city were purposively selected and interviewed. Data was subject to thematic analysis by researchers from nursing and information science. Saturation of themes was achieved. Results Participants were between 38 and 72 years, had been receiving kidney replacement therapy from 2 weeks to 31 years. Eight participants reported having access to the internet but none participated in chat rooms. The activities were conceptualized into themes as listening, seeking, searching, sharing and observing. These activities enabled people to create, reflect on and evaluate the information needed to inform their decision-making Conclusion/Application to Clinical Practice The information practice research approach will enable a better understanding of the underlying relationship between information, knowledge and experience to be better understood. For renal nurses who are involved in patient education being able to recognise the way people use information will assist in individualizing educational sessions and tailoring teaching strategies to make it more meaningful.

The development of a virtual reality environment to model the experience of schizophrenia

Virtual Reality (VR) techniques are increasingly being used for education about and in the treatment of certain types of mental illness. Research indicates that VR is delivering on its promised potential to provide enhanced training and treatment outcomes through incorporation of this high-end technology. Schizophrenia is a mental disorder affecting 1-2% of the population, and it is estimated 12-16% of hospital beds in Australia are occupied by patients with psychosis. Tragically, there is also an increased risk of suicide associated with this diagnosis. A significant research project being undertaken across the University of Queensland faculties of Health Sciences and EPSA (Engineering, Physical Sciences and Architecture) has constructed a number of virtual environments that reproduce the phenomena experienced by patients who have psychosis. Symptoms of psychosis include delusions, hallucinations and thought disorder. The VR environment will allow behavioral, exposure therapies to be conducted with exactly controlled exposure stimuli and an expected reduction in risk of harm. This paper reports on the current work of the project, previous stages of software development and the final goal to introduce VR to medical consulting rooms.

Network interactions and performance of a multi-function IEC 61850 process bus

New substation technology, such as non-conventional instrument transformers,and a need to reduce design and construction costs, are driving the adoption of Ethernet based digital process bus networks for high voltage substations. Protection and control applications can share a process bus, making more efficient use of the network infrastructure. This paper classifies and defines performance requirements for the protocols used in a process bus on the basis of application. These include GOOSE, SNMP and IEC 61850-9-2 sampled values. A method, based on the Multiple Spanning Tree Protocol (MSTP) and virtual local area networks, is presented that separates management and monitoring traffic from the rest of the process bus. A quantitative investigation of the interaction between various protocols used in a process bus is described. These tests also validate the effectiveness of the MSTP based traffic segregation method. While this paper focusses on a substation automation network, the results are applicable to other real-time industrial networks that implement multiple protocols. High volume sampled value data and time-critical circuit breaker tripping commands do not interact on a full duplex switched Ethernet network, even under very high network load conditions. This enables an efficient digital network to replace a large number of conventional analog connections between control rooms and high voltage switchyards.

Learning landscapes 2.0 : warning - assembly required

Twenty first century learners operate in organic, immersive environments. A pedagogy of student-centred learning is not a recipe for rooms. A contemporary learning environment is like a landscape that grows, morphs, and responds to the pressures of the context and micro-culture. There is no single adaptable solution, nor a suite of off-the-shelf answers; propositions must be customisable and infinitely variable. They must be indeterminate and changeable; based on the creation of learning places, not restrictive or constraining spaces. A sustainable solution will be un-fixed, responsive to the life cycle of the components and materials, able to be manipulated by the users; it will create and construct its own history. Learning occurs as formal education with situational knowledge structures, but also as informal learning, active learning, blended learning social learning, incidental learning, and unintended learning. These are not spatial concepts but socio-cultural patterns of discovery. Individual learning requirements must run free and need to be accommodated as the learner sees fit. The spatial solution must accommodate and enable a full array of learning situations. It is a system not an object. Three major components: 1. The determinate landscape: in-situ concrete 'plate' that is permanent. It predates the other components of the system and remains as a remnant/imprint/fossil after the other components of the system have been relocated. It is a functional learning landscape in its own right; enabling a variety of experiences and activities. 2. The indeterminate landscape: a kit of pre-fabricated 2-D panels assembled in a unique manner at each site to suit the client and context. Manufactured to the principles of design-for-disassembly. A symbiotic barnacle like system that attaches itself to the existing infrastructure through the determinate landscape which acts as a fast growth rhizome. A carapace of protective panels, infinitely variable to create enclosed, semi-enclosed, and open learning places. 3. The stations: pre-fabricated packages of highly-serviced space connected through the determinate landscape. Four main types of stations; wet-room learning centres, dry-room learning centres, ablutions, and low-impact building services. Entirely customised at the factory and delivered to site. The stations can be retro-fitted to suit a new context during relocation. Principles of design for disassembly: material principles • use recycled and recyclable materials • minimise the number of types of materials • no toxic materials • use lightweight materials • avoid secondary finishes • provide identification of material types component principles • minimise/standardise the number of types of components • use mechanical not chemical connections • design for use of common tools and equipment • provide easy access to all components • make component size to suite means of handling • provide built in means of handling • design to realistic tolerances • use a minimum number of connectors and a minimum number of types system principles • design for durability and repeated use • use prefabrication and mass production • provide spare components on site • sustain all assembly and material information

Building shared situational awareness in surgery through distributed dialogue

Background Failure to convey time-critical information to team members during surgery diminishes members’ perception of the dynamic information relevant to their task, and compromises shared situational awareness. This research reports the dialog around clinical decisions made by team members in the time-pressured and high-risk context of surgery, and the impact of these communications on shared situational awareness. Methods Fieldwork methods were used to capture the dynamic integration of individual and situational elements in surgery that provided the backdrop for clinical decisions. Nineteen semi structured interviews were performed with 24 participants from anaesthesia, surgery, and nursing in the operating rooms of a large metropolitan hospital in Queensland, Australia. Thematic analysis was used. Results: The domain “coordinating decisions in surgery” was generated from textual data. Within this domain, three themes illustrated the dialog of clinical decisions, i.e., synchronizing and strategizing actions, sharing local knowledge, and planning contingency decisions based on priority. Conclusion Strategies used to convey decisions that enhanced shared situational awareness included the use of “self-talk”, closed-loop communications, and “overhearing” conversations that occurred at the operating table. Behaviours’ that compromised a team’s shared situational awareness included tunnelling and fixating on one aspect of the situation.