A study on matching and multi-objective fuzzy control strategy of heavy truck suspension system

Matching method of heavy truck-rear air suspensions is discussed, and a fuzzy control strategy which improves both ride comfort and road friendliness of truck by adjusting damping coefficients of the suspension system is found. In the first place, a Dongfeng EQ1141G7DJ heavy truck’s ten DOF whole vehicle-road model was set up based on Matlab/Simulink and vehicle dynamics. Then appropriate passive air suspensions were chosen to replace the original rear leaf springs of the truck according to truck-suspension matching criterions, consequently, the stiffness of front leaf springs were adjusted too. Then the semi-active fuzzy controllers were designed for further enhancement of the truck’s ride comfort and the road friendliness. After the application of semi-active fuzzy control strategy through simulation, is was indicated that both ride comfort and road friendliness could be enhanced effectively under various road conditions. The strategy proposed may provide theory basis for design and development of truck suspension system in China.

Incorporating an economic model in the health impact assessment approach

The current policy decision making in Australia regarding non-health public investments (for example, transport/housing/social welfare programmes) does not quantify health benefits and costs systematically. To address this knowledge gap, this study proposes an economic model for quantifying health impacts of public policies in terms of dollar value. The intention is to enable policy-makers in conducting economic evaluation of health effects of non-health policies and in implementing policies those reduce health inequalities as well as enhance positive health gains of the target population. Health Impact Assessment (HIA) provides an appropriate framework for this study since HIA assesses the beneficial and adverse effects of a programme/policy on public health and on health inequalities through the distribution of those effects. However, HIA usually tries to influence the decision making process using its scientific findings, mostly epidemiological and toxicological evidence. In reality, this evidence can not establish causal links between policy and health impacts since it can not explain how an individual or a community reacts to changing circumstances. The proposed economic model addresses this health-policy linkage using a consumer choice approach that can explain changes in group and individual behaviour in a given economic set up. The economic model suggested in this paper links epidemiological findings with economic analysis to estimate the health costs and benefits of public investment policies. That is, estimating dollar impacts when health status of the exposed population group changes by public programmes – for example, transport initiatives to reduce congestion by building new roads/ highways/ tunnels etc. or by imposing congestion taxes. For policy evaluation purposes, the model is incorporated in the HIA framework by establishing association among identified factors, which drive changes in the behaviour of target population group and in turn, in the health outcomes. The economic variables identified to estimate the health inequality and health costs are levels of income, unemployment, education, age groups, disadvantaged population groups, mortality/morbidity etc. However, though the model validation using case studies and/or available database from Australian non-health policy (say, transport) arena is in the future tasks agenda, it is beyond the scope of this current paper.

Characterisation of soils with the use of instrumental techniques : a multivariate forensic study

The value of soil evidence in the forensic discipline is well known. However, it would be advantageous if an in-situ method was available that could record responses from tyre or shoe impressions in ground soil at the crime scene. The development of optical fibres and emerging portable NIR instruments has unveiled a potential methodology which could permit such a proposal. The NIR spectral region contains rich chemical information in the form of overtone and combination bands of the fundamental infrared absorptions and low-energy electronic transitions. This region has in the past, been perceived as being too complex for interpretation and consequently was scarcely utilized. The application of NIR in the forensic discipline is virtually non-existent creating a vacancy for research in this area. NIR spectroscopy has great potential in the forensic discipline as it is simple, nondestructive and capable of rapidly providing information relating to chemical composition. The objective of this study is to investigate the ability of NIR spectroscopy combined with Chemometrics to discriminate between individual soils. A further objective is to apply the NIR process to a simulated forensic scenario where soil transfer occurs. NIR spectra were recorded from twenty-seven soils sampled from the Logan region in South-East Queensland, Australia. A series of three high quartz soils were mixed with three different kaolinites in varying ratios and NIR spectra collected. Spectra were also collected from six soils as the temperature of the soils was ramped from room temperature up to 6000C. Finally, a forensic scenario was simulated where the transferral of ground soil to shoe soles was investigated. Chemometrics methods such as the commonly known Principal Component Analysis (PCA), the less well known fuzzy clustering (FC) and ranking by means of multicriteria decision making (MCDM) methodology were employed to interpret the spectral results. All soils were characterised using Inductively Coupled Plasma Optical Emission Spectroscopy and X-Ray Diffractometry. Results were promising revealing NIR combined with Chemometrics is capable of discriminating between the various soils. Peak assignments were established by comparing the spectra of known minerals with the spectra collected from the soil samples. The temperature dependent NIR analysis confirmed the assignments of the absorptions due to adsorbed and molecular bound water. The relative intensities of the identified NIR absorptions reflected the quantitative XRD and ICP characterisation results. PCA and FC analysis of the raw soils in the initial NIR investigation revealed that the soils were primarily distinguished on the basis of their relative quartz and kaolinte contents, and to a lesser extent on the horizon from which they originated. Furthermore, PCA could distinguish between the three kaolinites used in the study, suggesting that the NIR spectral region was sensitive enough to contain information describing variation within kaolinite itself. The forensic scenario simulation PCA successfully discriminated between the ‘Backyard Soil’ and ‘Melcann® Sand’, as well as the two sampling methods employed. Further PCA exploration revealed that it was possible to distinguish between the various shoes used in the simulation. In addition, it was possible to establish association between specific sampling sites on the shoe with the corresponding site remaining in the impression. The forensic application revealed some limitations of the process relating to moisture content and homogeneity of the soil. These limitations can both be overcome by simple sampling practices and maintaining the original integrity of the soil. The results from the forensic scenario simulation proved that the concept shows great promise in the forensic discipline.

Managing a portfolio of corporate venture units : challenges in achieving within-unit focus and between-unit coordination

Principal Topic: There is increasing recognition that the organizational configurations of corporate venture units should depend on the types of ventures the unit seeks to develop (Burgelman, 1984; Hill and Birkinshaw, 2008). Distinction have been made between internal and external as well as exploitative versus explorative ventures (Hill and Birkinshaw, 2008; Narayan et al., 2009; Schildt et al., 2005). Assuming that firms do not want to limit themselves to a single type of venture, but rather employ a portfolio of ventures, the logical consequence is that firms should employ multiple corporate venture units. Each venture unit tailor-made for the type of venture it seeks to develop. Surprisingly, there is limited attention in the literature for the challenges of managing multiple corporate venture units in a single firm. Maintaining multiple venture units within one firm provides easier access to funding for new ideas (Hamel, 1999). It allows for freedom and flexibility to tie the organizational systems (Rice et al., 2000), autonomy (Hill and Rothaermel, 2003), and involvement of management (Day, 1994; Wadwha and Kotha, 2006) to the requirements of the individual ventures. Yet, the strategic objectives of a venture may change when uncertainty around the venture is resolved (Burgelman, 1984). For example, firms may decide to spin-in external ventures (Chesbrough, 2002) or spun-out ventures that prove strategically unimportant (Burgelman, 1984). This suggests that ventures might need to be transferred between venture units, e.g. from a more internally-driven corporate venture division to a corporate venture capital unit. Several studies suggested that ventures require different managerial skills across their phase of development (Desouza et al., 2007; O'Connor and Ayers, 2005; Kazanjian and Drazin, 1990; Westerman et al., 2006). To facilitate effective transfer between venture units and manage the overall venturing process, it is important that firms set up and manage integrative linkages. Integrative linkages provide synergies and coordination between differentiated units (Lawrence and Lorsch, 1967). Prior findings pointed to the important role of senior management (Westerman et al., 2006; Gilbert, 2006) and a shared organizational vision (Burgers et al., 2009) to coordinate venture units with mainstream businesses. We will draw on these literatures to investigate the key question of how to integratively manage multiple venture units. ---------- Methodology/Key Propositions: In order to seek an answer to the research question, we employ a case study approach that provides unique insights into how firms can break up their venturing process. We selected three Fortune 500 companies that employ multiple venturing units, IBM, Royal Dutch/ Shell and Nokia, and investigated and compared their approaches. It was important that the case companies somewhat differed in the type of venture units they employed as well as the way they integrate and coordinate their venture units. The data are based on extensive interviews and a variety of internal and external company documents to triangulate our findings (Eisenhardt, 1989). The key proposition of the article is that firms can best manage their multiple venture units through an ambidextrous design of loosely coupled units. This provides venture units with sufficient flexibility to employ organizational configurations that best support the type of venture they seek to develop, as well as provides sufficient integration to facilitate smooth transfer of ventures between venture units. Based on the case findings, we develop a generic framework for a new way of managing the venturing process through multiple corporate venture units. ---------- Results and Implications: One of our main findings is that these firms tend to organize their venture units according to phases in the venture development process. That is, they tend to have venture units aimed at incubation of venture ideas as well as units aimed more at the commercialization of ventures into a new business unit for the firm or a start-up. The companies in our case studies tended to coordinate venture units through integrative management skills or a coordinative venture unit that spanned multiple phases. We believe this paper makes two significant contributions. First, we extend prior venturing literature by addressing how firms manage a portfolio of venture units, each achieving different strategic objectives. Second, our framework provides recommendations on how firms should manage such an approach towards venturing. This helps to increase the likelihood of success of their venturing programs.

Reflections on the Hong Kong CIRC report

The Government of the Hong Kong SAR sponsored a report investigating the Hong Kong construction inudstry and published the investigating committee's findings in 2001 (HK CIRC 2001). Since then the Provisional Construction Industry Coordination Board (PCICB), and its successor, the Construction Industry Council (CIC), also set up by the Government, has made progress with the necessary reforms. Now that seven years have passed, it is time for an independent evaluation of the impact of the CIRC initiative in order to assist the CIC and the Government decision-makers in refining the efforts to improve the industry's performance. This paper reports on the interim results of a study that seeks to provide such an evaluation.

Design and evaluation of a prototype tracking system

In this paper, we present the design and construction of a prototype target tracking system. The experimental set up consists of three main modules for moving the object, detecting the motion of the object and its tracking. The mechanism for moving the object includes an object and two stepper motors and their driving and control circuitry. The detection of the object’s motion is realized by photo switch array. The tracking mechanism consists of a laser beam and two DC servomotors and their associated circuitry. The control algorithm is a standard fuzzy logic controller. The system is designed to operate in two modes in such a way that the role of target and tracker can be interchanged. Experimental results indicate that the fuzzy controller is capable of controlling the system in both modes.

The record producer as nexus : creative inspiration, technology and the recording industry

What is a record producer? There is a degree of mystery and uncertainty about just what goes on behind the studio door. Some producers are seen as Svengali-like figures manipulating artists into mass consumer product. Producers are sometimes seen as mere technicians whose job is simply to set up a few microphones and press the record button. Close examination of the recording process will show how far this is from a complete picture. Artists are special—they come with an inspiration, and a talent, but also with a variety of complications, and in many ways a recording studio can seem the least likely place for creative expression and for an affective performance to happen. The task of the record producer is to engage with these artists and their songs and turn these potentials into form through the technology of the recording studio. The purpose of the exercise is to disseminate this fixed form to an imagined audience—generally in the hope that this audience will prove to be real. Finding an audience is the role of the record company. A record producer must also engage with the commercial expectations of the interests that underwrite a recording. This dissertation considers three fields of interest in the recording process: the performer and the song; the technology of the recording context; and the commercial ambitions of the record company—and positions the record producer as a nexus at the interface of all three. The author reports his structured recollection of five recordings, with three different artists, that all achieved substantial commercial success. The processes are considered from the author’s perspective as the record producer, and from inception of the project to completion of the recorded work. What were the processes of engagement? Do the actions reported conform to the template of nexus? This dissertation proposes that in all recordings the function of producer/nexus is present and necessary—it exists in the interaction of the artistry and the technology. The art of record production is to engage with these artists and the songs they bring and turn these potentials into form.

Using a siphon to drain floodwaters

This article describes how to use a siphon to drain floodwaters. A siphon is a tube that conveys water to a lower level via point above the upper water level by gravity. A siphon can be set up to drain existing floodwaters more quickly than they would naturally and can also prevent flooding. Siphons are particularly useful in situations where no pump is available, and a drainage point exists lower than the level of the floodwaters. Some case studies are presented.

When sparks fly : developing formal mentoring programs for the career development of young and emerging artists

Formal mentoring programs are accepted as a valuable strategy for developing young and emerging artists. This thesis presents the results of an evaluation of the SPARK National Young Artists Mentoring Program (SPARK). SPARK was a ten-month formal mentoring program managed by Youth Arts Queensland (YAQ) on behalf of the Australia Council for the Arts from 2003-2009. The program aimed to assist young and emerging Australian artists between the ages of 18-26 to establish a professional career in the arts. It was a highly successful formal arts mentoring program that facilitated 58 mentorships between young and emerging artists and professional artists from across Australia in five program rounds over its seven year lifespan. Interest from other cultural organisations looking to develop their own formal mentoring programs encouraged YAQ to commission this research to determine how the program works to achieve its effects. This study was conducted with young and emerging artists who participated in SPARK from 2003 to 2008. It took a theory-driven evaluation approach to examine SPARK as an example of what makes formal arts mentoring programs effective. It focused on understanding the program’s theory or how the program worked to achieve its desired outcomes. The program activities and assumed responses to program activities were mapped out in a theories of change model. This theoretical framework was then used to plan the points for data collection. Through the process of data collection, actual program developments were compared to the theoretical framework to see what occurred as expected and what did not. The findings were then generalised for knowledge and wider application. The findings demonstrated that SPARK was a successful and effective program and an exemplar model of a formal mentoring program preparing young and emerging artists for professional careers in the arts. They also indicate several ways in which this already strong program could be further improved, including: looking at the way mentoring relationships are set up and how the mentoring process is managed; considering the balance between artistic and professional development; developing career development competencies and networking skills; taking into account the needs of young and emerging artists to develop their professional identity and build confidence; and giving more thought to the desired program outcomes and considering the issue of timeliness and readiness for career transition. From these findings, together with principles outlined in the mentoring and career development literature, a number of necessary conditions have been identified for developing effective mentoring programs in the career development of young and emerging artists.

Striving to realise the European idea : judging the news media’s accounts of how the Berlin Wall gave impetus to a new order across Europe

The 1990 European Community was taken by surprise, by the urgency of demands from the newly-elected Eastern European governments to become member countries. Those governments were honouring the mass social movement of the streets, the year before, demanding free elections and a liberal economic system associated with “Europe”. The mass movement had actually been accompanied by much activity within institutional politics, in Western Europe, the former “satellite” states, the Soviet Union and the United States, to set up new structures – with German reunification and an expanded EC as the centre-piece. This paper draws on the writer’s doctoral dissertation on mass media in the collapse of the Eastern bloc, focused on the Berlin Wall – documenting both public protests and institutional negotiations. For example the writer as a correspondent in Europe from that time, recounts interventions of the German Chancellor, Helmut Kohl, at a European summit in Paris nine days after the “Wall”, and separate negotiations with the French President, Francois Mitterrand -- on the reunification, and EU monetary union after 1992. Through such processes, the “European idea” would receive fresh impetus, though the EU which eventuated, came with many altered expectations. It is argued here that as a result of the shock of 1989, a “social” Europe can be seen emerging, as a shared experience of daily life -- especially among people born during the last two decades of European consolidation. The paper draws on the author’s major research, in four parts: (1) Field observation from the strategic vantage point of a news correspondent. This includes a treatment of evidence at the time, of the wishes and intentions of the mass public (including the unexpected drive to join the European Community), and those of governments, (e.g. thoughts of a “Tienanmen Square solution” in East Berlin, versus the non-intervention policies of the Soviet leader, Mikhail Gorbachev). (2) A review of coverage of the crisis of 1989 by major news media outlets, treated as a history of the process. (3) As a comparison, and a test of accuracy and analysis; a review of conventional histories of the crisis appearing a decade later.(4) A further review, and test, provided by journalists responsible for the coverage of the time, as reflection on practice – obtained from semi-structured interviews.

Bubble rise velocity and trajectory in xanthan gum crystal suspension

An experimental set-up was used to visually observe the characteristics of bubbles as they moved up a column holding xanthan gum crystal suspensions. The bubble rise characteristics in xanthan gum solutions with crystal suspension are presented in this paper. The suspensions were made by using different concentrations of xanthan gum solutions with 0.23 mm mean diameter polystyrene crystal particles. The influence of the dimensionless quantities; namely the Reynolds number, Re, the Weber number, We, and the drag co-efficient, cd, are identified for the determination of the bubble rise velocity. The effect of these dimensionless groups together with the Eötvös number, Eo, the Froude number, Fr, and the bubble deformation parameter, D, on the bubble rise velocity and bubble trajectory are analysed. The experimental results show that the average bubble velocity increases with the increase in bubble volume for xanthan gum crystal suspensions. At high We, Eo and Re, bubbles are spherical-capped and their velocities are found to be very high. At low We and Eo, the surface tension force is significant compared to the inertia force. The viscous forces were shown to have no substantial effect on the bubble rise velocity for 45 < Re < 299. The results show that the drag co-efficient decreases with the increase in bubble velocity and Re. The trajectory analysis showed that small bubbles followed a zigzag motion while larger bubbles followed a spiral motion. The smaller bubbles experienced less horizontal motion in crystal suspended xanthan gum solutions while larger bubbles exhibited a greater degree of spiral motion than those seen in the previous studies on the bubble rise in xanthan gum solutions without crystal.

Assessment of commercial network RTK user positioning performance over long inter-station distances

The paper provides an assessment of the performance of commercial Real Time Kinematic (RTK) systems over longer than recommended inter-station distances. The experiments were set up to test and analyse solutions from the i-MAX, MAX and VRS systems being operated with three triangle shaped network cells, each having an average inter-station distance of 69km, 118km and 166km. The performance characteristics appraised included initialization success rate, initialization time, RTK position accuracy and availability, ambiguity resolution risk and RTK integrity risk in order to provide a wider perspective of the performance of the testing systems. ----- ----- The results showed that the performances of all network RTK solutions assessed were affected by the increase in the inter-station distances to similar degrees. The MAX solution achieved the highest initialization success rate of 96.6% on average, albeit with a longer initialisation time. Two VRS approaches achieved lower initialization success rate of 80% over the large triangle. In terms of RTK positioning accuracy after successful initialisation, the results indicated a good agreement between the actual error growth in both horizontal and vertical components and the accuracy specified in the RMS and part per million (ppm) values by the manufacturers. ----- ----- Additionally, the VRS approaches performed better than the MAX and i-MAX when being tested under the standard triangle network with a mean inter-station distance of 69km. However as the inter-station distance increases, the network RTK software may fail to generate VRS correction and then may turn to operate in the nearest single-base RTK (or RAW) mode. The position uncertainty reached beyond 2 meters occasionally, showing that the RTK rover software was using an incorrect ambiguity fixed solution to estimate the rover position rather than automatically dropping back to using an ambiguity float solution. Results identified that the risk of incorrectly resolving ambiguities reached 18%, 20%, 13% and 25% for i-MAX, MAX, Leica VRS and Trimble VRS respectively when operating over the large triangle network. Additionally, the Coordinate Quality indicator values given by the Leica GX1230 GG rover receiver tended to be over-optimistic and not functioning well with the identification of incorrectly fixed integer ambiguity solutions. In summary, this independent assessment has identified some problems and failures that can occur in all of the systems tested, especially when being pushed beyond the recommended limits. While such failures are expected, they can offer useful insights into where users should be wary and how manufacturers might improve their products. The results also demonstrate that integrity monitoring of RTK solutions is indeed necessary for precision applications, thus deserving serious attention from researchers and system providers.

Geometry‐specified troposphere decorrelation for subcentimeter real‐time kinematic solutions over long baselines

Real‐time kinematic (RTK) GPS techniques have been extensively developed for applications including surveying, structural monitoring, and machine automation. Limitations of the existing RTK techniques that hinder their applications for geodynamics purposes are twofold: (1) the achievable RTK accuracy is on the level of a few centimeters and the uncertainty of vertical component is 1.5–2 times worse than those of horizontal components and (2) the RTK position uncertainty grows in proportional to the base‐torover distances. The key limiting factor behind the problems is the significant effect of residual tropospheric errors on the positioning solutions, especially on the highly correlated height component. This paper develops the geometry‐specified troposphere decorrelation strategy to achieve the subcentimeter kinematic positioning accuracy in all three components. The key is to set up a relative zenith tropospheric delay (RZTD) parameter to absorb the residual tropospheric effects and to solve the established model as an ill‐posed problem using the regularization method. In order to compute a reasonable regularization parameter to obtain an optimal regularized solution, the covariance matrix of positional parameters estimated without the RZTD parameter, which is characterized by observation geometry, is used to replace the quadratic matrix of their “true” values. As a result, the regularization parameter is adaptively computed with variation of observation geometry. The experiment results show that new method can efficiently alleviate the model’s ill condition and stabilize the solution from a single data epoch. Compared to the results from the conventional least squares method, the new method can improve the longrange RTK solution precision from several centimeters to the subcentimeter in all components. More significantly, the precision of the height component is even higher. Several geosciences applications that require subcentimeter real‐time solutions can largely benefit from the proposed approach, such as monitoring of earthquakes and large dams in real‐time, high‐precision GPS leveling and refinement of the vertical datum. In addition, the high‐resolution RZTD solutions can contribute to effective recovery of tropospheric slant path delays in order to establish a 4‐D troposphere tomography.

Full Circle : a collection of prototypes

This exhibition engages with one of the key issues facing the fashion textiles industry in terms of future sustainability: that of the well being of fashion industry workers in Australia and New Zealand (people). This collection formed the basis of my honours dissertation (completed in New Zealand in 2008) which examines the contribution that design can make to sustainable manufacturing; particularly design for local production and consumption. An important aspect this work is the discussion of source, the work suggests that the made in China syndrome (in reference to the current state of over-consumerism in Australia and New Zealand) could be bought to a close through design to minimize waste and maximize opportunity for ‘people’: in this case both garment workers and the SMEs that employ them. The garments reflect the possibilities of focusing on a local approach that could be put into practice by a framework of SMEs that already exist. In addition the design process is highly transferrable and could be put into practice almost anywhere with minimal set up costs and a design ethos that progresses at the same pace as the skills of workers. This collection is a physical and conceptual embodiment of a source local/make local/sell local approach. The collection is an example of design that demonstrates that this is not an unrealistic ideal and is in fact possible through the development of a sustainable industry, in the sense of people, profit and planet, through adoption of a design process model that stops the waste at the source, by making better use of the raw materials and labour involved in making fashion garments. Although the focus of this research appears to centre on people and profit, this kind of source local/make local/sell local approach also has great benefits in terms of environmental sustainability.

A solid state Marx generator with a novel configuration

The new configuration proposed in this paper for Marx Generator (MG) aims to generate high voltage for pulsed power applications through reduced number of semiconductor components with a more efficient load supplying process. The main idea is to charge two groups of capacitors in parallel through an inductor and take advantage of resonant phenomenon in charging each capacitor up to a double input voltage level. In each resonant half a cycle, one of those capacitor groups are charged, and eventually the charged capacitors will be connected in series and the summation of the capacitor voltages can be appeared at the output of the topology. This topology can be considered as a modified Marx generator which works based on the resonant concept. Simulated models of this converter have been investigated in Matlab/SIMULINK platform and a prototype set up has been implemented in laboratory. The acquired results of either fully satisfy the anticipations in proper operation of the converter.