Mathematical modelling of controlled drug release from polymer micro-spheres : incorporating the effects of swelling, diffusion and dissolution via moving boundary problems

Controlled drug delivery is a key topic in modern pharmacotherapy, where controlled drug delivery devices are required to prolong the period of release, maintain a constant release rate, or release the drug with a predetermined release profile. In the pharmaceutical industry, the development process of a controlled drug delivery device may be facilitated enormously by the mathematical modelling of drug release mechanisms, directly decreasing the number of necessary experiments. Such mathematical modelling is difficult because several mechanisms are involved during the drug release process. The main drug release mechanisms of a controlled release device are based on the device’s physiochemical properties, and include diffusion, swelling and erosion. In this thesis, four controlled drug delivery models are investigated. These four models selectively involve the solvent penetration into the polymeric device, the swelling of the polymer, the polymer erosion and the drug diffusion out of the device but all share two common key features. The first is that the solvent penetration into the polymer causes the transition of the polymer from a glassy state into a rubbery state. The interface between the two states of the polymer is modelled as a moving boundary and the speed of this interface is governed by a kinetic law. The second feature is that drug diffusion only happens in the rubbery region of the polymer, with a nonlinear diffusion coefficient which is dependent on the concentration of solvent. These models are analysed by using both formal asymptotics and numerical computation, where front-fixing methods and the method of lines with finite difference approximations are used to solve these models numerically. This numerical scheme is conservative, accurate and easily implemented to the moving boundary problems and is thoroughly explained in Section 3.2. From the small time asymptotic analysis in Sections 5.3.1, 6.3.1 and 7.2.1, these models exhibit the non-Fickian behaviour referred to as Case II diffusion, and an initial constant rate of drug release which is appealing to the pharmaceutical industry because this indicates zeroorder release. The numerical results of the models qualitatively confirms the experimental behaviour identified in the literature. The knowledge obtained from investigating these models can help to develop more complex multi-layered drug delivery devices in order to achieve sophisticated drug release profiles. A multi-layer matrix tablet, which consists of a number of polymer layers designed to provide sustainable and constant drug release or bimodal drug release, is also discussed in this research. The moving boundary problem describing the solvent penetration into the polymer also arises in melting and freezing problems which have been modelled as the classical onephase Stefan problem. The classical one-phase Stefan problem has unrealistic singularities existed in the problem at the complete melting time. Hence we investigate the effect of including the kinetic undercooling to the melting problem and this problem is called the one-phase Stefan problem with kinetic undercooling. Interestingly we discover the unrealistic singularities existed in the classical one-phase Stefan problem at the complete melting time are regularised and also find out the small time behaviour of the one-phase Stefan problem with kinetic undercooling is different to the classical one-phase Stefan problem from the small time asymptotic analysis in Section 3.3. In the case of melting very small particles, it is known that surface tension effects are important. The effect of including the surface tension to the melting problem for nanoparticles (no kinetic undercooling) has been investigated in the past, however the one-phase Stefan problem with surface tension exhibits finite-time blow-up. Therefore we investigate the effect of including both the surface tension and kinetic undercooling to the melting problem for nanoparticles and find out the the solution continues to exist until complete melting. The investigation of including kinetic undercooling and surface tension to the melting problems reveals more insight into the regularisations of unphysical singularities in the classical one-phase Stefan problem. This investigation gives a better understanding of melting a particle, and contributes to the current body of knowledge related to melting and freezing due to heat conduction.

Effect of CT electron density identification on Monte Carlo simulations of radiotherapeutic treatments

Introduction: The accurate identification of tissue electron densities is of great importance for Monte Carlo (MC) dose calculations. When converting patient CT data into a voxelised format suitable for MC simulations, however, it is common to simplify the assignment of electron densities so that the complex tissues existing in the human body are categorized into a few basic types. This study examines the effects that the assignment of tissue types and the calculation of densities can have on the results of MC simulations, for the particular case of a Siemen’s Sensation 4 CT scanner located in a radiotherapy centre where QA measurements are routinely made using 11 tissue types (plus air). Methods: DOSXYZnrc phantoms are generated from CT data, using the CTCREATE user code, with the relationship between Hounsfield units (HU) and density determined via linear interpolation between a series of specified points on the ‘CT-density ramp’ (see Figure 1(a)). Tissue types are assigned according to HU ranges. Each voxel in the DOSXYZnrc phantom therefore has an electron density (electrons/cm3) defined by the product of the mass density (from the HU conversion) and the intrinsic electron density (electrons /gram) (from the material assignment), in that voxel. In this study, we consider the problems of density conversion and material identification separately: the CT-density ramp is simplified by decreasing the number of points which define it from 12 down to 8, 3 and 2; and the material-type-assignment is varied by defining the materials which comprise our test phantom (a Supertech head) as two tissues and bone, two plastics and bone, water only and (as an extreme case) lead only. The effect of these parameters on radiological thickness maps derived from simulated portal images is investigated. Results & Discussion: Increasing the degree of simplification of the CT-density ramp results in an increasing effect on the resulting radiological thickness calculated for the Supertech head phantom. For instance, defining the CT-density ramp using 8 points, instead of 12, results in a maximum radiological thickness change of 0.2 cm, whereas defining the CT-density ramp using only 2 points results in a maximum radiological thickness change of 11.2 cm. Changing the definition of the materials comprising the phantom between water and plastic and tissue results in millimetre-scale changes to the resulting radiological thickness. When the entire phantom is defined as lead, this alteration changes the calculated radiological thickness by a maximum of 9.7 cm. Evidently, the simplification of the CT-density ramp has a greater effect on the resulting radiological thickness map than does the alteration of the assignment of tissue types. Conclusions: It is possible to alter the definitions of the tissue types comprising the phantom (or patient) without substantially altering the results of simulated portal images. However, these images are very sensitive to the accurate identification of the HU-density relationship. When converting data from a patient’s CT into a MC simulation phantom, therefore, all possible care should be taken to accurately reproduce the conversion between HU and mass density, for the specific CT scanner used. Acknowledgements: This work is funded by the NHMRC, through a project grant, and supported by the Queensland University of Technology (QUT) and the Royal Brisbane and Women's Hospital (RBWH), Brisbane, Australia. The authors are grateful to the staff of the RBWH, especially Darren Cassidy, for assistance in obtaining the phantom CT data used in this study. The authors also wish to thank Cathy Hargrave, of QUT, for assistance in formatting the CT data, using the Pinnacle TPS. Computational resources and services used in this work were provided by the HPC and Research Support Group, QUT, Brisbane, Australia.

Critical reflection on the SIA’s professional project and the body of knowledge

Over the last few years the Safety Institute of Australia (SIA) has developed and implemented a number of strategies to gain professional status for the ‘generalist occupational health and safety professional’. Two of the most significant developments have been the publication of the ‘Core Body of Knowledge for the Generalist OHS Professional.’ and the accreditation of university OHS courses. Despite a considerable amount of work aimed at gaining professional status there has not been any public debate or reflection about how the professionalisation project may impact on OHS and how the project is being conducted. Professionalisation has been vigorously promoted as a sign of maturity for the SIA and which will provide unmitigated benefits for workplace health and safety. The aim of this paper is to critically reflect on the processes of professionalisation (the professional project) and discuss some of the ways in which this project may shape the field of occupational health and safety. The implications for the role of universities will also be discussed.

Screening in early childhood for risk of later mental health problems : a longitudinal study

Depression in childhood or adolescence is associated with increased rates of depression in adulthood. Does this justify efforts to detect (and treat) those with symptoms of depression in early childhood or adolescence? The aim of this study was to determine how well symptoms of anxiety/depression (A-D) in early childhood and adolescence predict adult mental health. The study sample is taken from a population-based prospective birth cohort study. Of the 8556 mothers initially approached to participate 8458 agreed, of whom 7223 mothers gave birth to a live singleton baby. Children were screened using modified Child Behaviour Checklist (CBCL) scales for internalizing and total problems (T-P) at age 5 and the CBCL and Youth Self Report (YSR) A-D subscale and T-P scale at age 14. At age 21, a sub-sample of 2563 young adults in this cohort were administered the CIDI-Auto. Results indicated that screening at age 5 would detect few later cases of significant mental ill-health. Using a cut-point of 20% for internalizing at child age 5 years the CBCL had sensitivities of only 25% and 18% for major depression and anxiety disorders at 21 years, respectively. At age 14, the YSR generally performed a little better than the CBCL as a screening instrument, but neither performed at a satisfactory level. Of the children who were categorised as having YSR A-D at 14 years 30% and 37% met DSM-IV criteria for major depression and anxiety disorders, respectively, at age 21. Our findings challenge an existing movement encouraging the detection and treatment of those with symptoms of mental illness in early childhood.

Food and Brisbane households : dietary, social and health consequences of food insecurity

Background & Aims: Access to sufficient amounts of safe and culturally-acceptable foods is a fundamental human right. Food security exists when all people, at all times, have physical, social, and economic access to sufficient, safe and nutritious food to meet their dietary needs and food preferences for an active and healthy life. Food insecurity therefore occurs when the availability or access to sufficient amounts of nutritionally-adequate, culturally-appropriate and safe foods, or, the ability to acquire such foods in socially-acceptable ways, is limited. Food insecurity may result in significant adverse effects for the individual and these outcomes may vary between adults and children. Among adults, food insecurity may be associated with overweight or obesity, poorer self-rated general health, depression, increased health-care utilisation and dietary intakes less consistent with national recommendations. Among children, food insecurity may result in poorer self or parent-reported general health, behavioural problems, lower levels of academic achievement and poor social outcomes. The majority of research investigating the potential correlates of food insecurity has been undertaken in the United States (US), where regular national screening for food insecurity is undertaken using a comprehensive multi-item measurement. In Australia, screening for food insecurity takes place on a three yearly basis via the use of a crude, single-item included in the National Health Survey (NHS). This measure has been shown to underestimate the prevalence of food insecurity by 5%. From 1995 – 2004, the prevalence of food insecurity among the Australian population remained stable at 5%. Due to the perceived low prevalence of this issue, screening for food insecurity was not undertaken in the most recent NHS. Furthermore, there are few Australian studies investigating the potential determinants of food insecurity and none investigating potential outcomes among adults and children. This study aimed to examine these issues by a) investigating the prevalence of food insecurity among households residing in disadvantaged urban areas and comparing prevalence rates estimated by the more comprehensive 18-item and 6-item United States Department of Agriculture (USDA) Food Security Survey Module (FSSM) to those estimated by the current single-item measure used for surveillance in Australia and b) investigating the potential determinants and outcomes of food insecurity, Methods: A comprehensive literature review was undertaken to investigate the potential determinants and consequences of food insecurity among developed countries. This was followed by a cross-sectional study in which 1000 households from the most disadvantaged 5% of Brisbane areas were sampled and data collected via mail-based survey (final response rate = 53%, n = 505). Data were collected for food security status, sociodemographic characteristics (household income, education, age, gender, employment status, housing tenure and living arrangements), fruit and vegetable intakes, meat and take-away consumption, presence of depressive symptoms, presence of chronic disease and body mass index (BMI) among adults. Among children, data pertaining to BMI, parent-reported general health, days away from school and activities and behavioural problems were collected. Rasch analysis was used to investigate the psychometric properties of the 18-, 10- and 6-item adaptations of the USDA-FSSM, and McNemar's test was used to investigate the difference in the prevalence of food insecurity as measured by these three adaptations compared to the current single-item measure used in Australia. Chi square and logistic regression were used to investigate the differences in dietary and health outcomes among adults and health and behavioural outcomes among children. Results were adjusted for equivalised household income and, where necessary, for indigenous status, education and family type. Results: Overall, 25% of households in these urbanised-disadvantaged areas reported experiencing food insecurity; this increased to 34% when only households with children were analysed. The current reliance on a single-item measure to screen for food insecurity may underestimate the true burden among the Australian population, as this measure was shown to significantly underestimate the prevalence of food insecurity by five percentage points. Internationally, major potential determinants of food insecurity included poverty and indicators of poverty, such as low-income, unemployment and lower levels of education. Ethnicity, age, transportation and cooking and financial skills were also found to be potential determinants of food insecurity. Among Australian adults in disadvantaged urban areas, food insecurity was associated with a three-fold increase in experiencing poorer self-rated general health and a two-to-five-fold increase in the risk of depression. Furthermore, adults from food insecure households were twoto- three times more likely to have seen a general practitioner and/or been admitted to hospital within the previous six months, compared to their food secure counterparts. Weight status and intakes of fruits, vegetables and meat were not associated with food insecurity. Among Australian households with children, those in the lowest tertile were over 16 times more likely to experience food insecurity compared to those in the highest tertile for income. After adjustment for equivalised household income, children from food insecure households were three times more likely to have missed days away from school or other activities. Furthermore, children from food insecure households displayed a two-fold increase in atypical emotions and behavioural difficulties. Conclusions: Food insecurity is an important public health issue and may contribute to the burden on the health care system through its associations with depression and increased health care utilisation among adults and behavioural and emotional problems among children. Current efforts to monitor food insecurity in Australia do not occur frequently and use a tool that may underestimate the prevalence of food insecurity. Efforts should be made to improve the regularity of screening for food insecurity via the use of a more accurate screening measure. Most of the current strategies that aim to alleviate food insecurity do not sufficiently address the issue of insufficient financial resources for acquiring food; a factor which is an important determinant of food insecurity. Programs to address this issue should be developed in collaboration with groups at higher risk of developing food insecurity and should incorporate strategies to address the issue of low income as a barrier to food acquisition.

Screening for risk of later mental health problems : a longitudinal study

Purpose: This is one of the first studies to report that the Achenbach internalising scales were much more effective at identifying those with current comorbid depression and anxiety, rather than individual mood disorder. Introduction: The Achenbach behaviour checklists (YSR,YASR) are widely used, low cost screening tools used to assess problem behaviour. Several studies report good association between the checklists and psychiatric diagnoses; although with varying degrees of agreement. Most are cross-sectional studies involving adolescents referred to mental health services; few are in large community-based studies. This study examined the usefulness of the Achenbach internalising scales in the primary screening (both predictive and concurrent)for depression and anxiety. Methods: The sample was 2400 young adults from an Australian population-based prospective birth cohort study. The association between the empirical anxiety and depression scales were individually assessed against DSM-IV depression and anxiety diagnoses. Odds ratios and diagnostic efficiency tests report the findings. Results: Adolescents with internalising symptoms were twice (OR 2.3, 95%CI 1.7 to 3.1) as likely to be diagnosed with later DSM-IV depression. YASR internalising scale predicted DSM-IV mood disorders (depression OR = 6.9, 95% CI 5.0–9.5; anxiety OR = 5.1, 95% CI 3.8–6.7) in the previous 12 months. The internalising scales were much more effective at identifying those with comorbid depression and anxiety. Conclusions: Adolescence and early adulthood are key risk periods for the onset of anxiety and depression. This study found that young people with internalising behaviour problems were more likely to have comorbid depression and anxiety DSM-IV disorder.

A preliminary study on assessing body burden of persistent organic pollutants (POPs) in infants through analysis of faeces

Most persistent organic pollutants (POPs) like polychlorinated biphenyls (PCBs), a range of polybrominated diphenyl ethers (PBDEs) and organochlorine pesticides (OCPs) are readily absorbed (via the ingestion and inhalation) and accumulate in fatty tissue, including adipose tissue and human milk [1]. Health effects related to exposure to these chemicals may include neurological effects, altered functioning of the nervous system and/or endocrine disruption [2-4]. The burden of environmental disease is recognized as much higher for children than adults, especially in young children under 5 years of age worldwide [5]. There is increased concern regarding the environmental impact on the health of children who have been disproportionately affected by environmental problems. For example they may be subjected to relatively higher exposure, have greater physiological susceptibility and/or suffer more extreme consequences due to growth [6-9]. It is therefore worthwhile to assess the correlation between burden of disease and exposure to xenobiotic chemical pollutants like POPs. Such assessment may provide guidance for legislative changes regarding chemical bans and give reliable advice to parents including lactating mothers.

New criterion for the stability of a human body in floodwaters

The authors must be congratulated for their original and important study. The flooding of urbanised areas constitutes a hazard to the population and infrastructure. Floods through inundated urban environments have been studied only recently and few considered the potential impact of flowing waters on pedestrians...

Assessment of body composition in Indian adults: comparison between dual-energy X-ray absorptiometry and isotope dilution technique

Dual-energy X-ray absorptiometry (DXA) and isotope dilution technique have been used as reference methods to validate the estimates of body composition by simple field techniques; however, very few studies have compared these two methods. We compared the estimates of body composition by DXA and isotope dilution (18O) technique in apparently healthy Indian men and women (aged 19–70 years, n 152, 48 % men) with a wide range of BMI (14–40 kg/m2). Isotopic enrichment was assessed by isotope ratio mass spectroscopy. The agreement between the estimates of body composition measured by the two techniques was assessed by the Bland–Altman method. The mean age and BMI were 37 (SD 15) years and 23·3 (SD 5·1) kg/m2, respectively, for men and 37 (SD 14) years and 24·1 (SD 5·8) kg/m2, respectively, for women. The estimates of fat-free mass were higher by about 7 (95 % CI 6, 9) %, those of fat mass were lower by about 21 (95 % CI 218,223) %, and those of body fat percentage (BF%) were lower by about 7·4 (95 % CI 28·2, 26·6) % as obtained by DXA compared with the isotope dilution technique. The Bland–Altman analysis showed wide limits of agreement that indicated poor agreement between the methods. The bias in the estimates of BF% was higher at the lower values of BF%. Thus, the two commonly used reference methods showed substantial differences in the estimates of body composition with wide limits of agreement. As the estimates of body composition are method-dependent, the two methods cannot be used interchangeably

Regulating supply-chains to address the occupational health and safety problems associated with precarious employment: The case of home-based clothing workers in Australia

Over the past 20 years the labour market, workforce and work organisation of most if not all industrialised countries have been significantly refashioned by the increased use of more flexible work arrangements, variously labelled as precarious employment or contingent work. There is now a substantial and growing body of international evidence that many of these arrangements are associated with a significant deterioration in occupational health and safety (OHS), using a range of measures such as injury rates, disease, hazard exposures and work-related stress. Moreover, there is an emerging body of evidence that these arrangements pose particular problems for conventional regulatory regimes. Recognition of these problems has aroused the concern of policy makers - especially in Europe, North America and Australia - and a number of responses have been adopted in terms of modifying legislation, producing new guidance material and codes of practice and revised enforcement practices. This article describes one such in itiative in Australia with regard to home-based clothing workers. The regulatory strategy developed in one Australian jurisdiction (and now being ‘exported’ into others) seeks to counter this process via contractual tracking mechanisms to follow the work, tie in liability and shift overarching legal responsibility to the top of the supply chain. The process also entails the integration of minimum standards relating to wages, hours and working conditions; OHS and access to workers’ compensation. While home-based clothing manufacture represents a very old type of ‘flexible’ work arrangement, it is one that regulators have found especially difficult to address. Further, the elaborate multi-tiered subcont racting and diffuse work locations found in this industry are also characteristic of newer forms of contingent work in other industries (such as some telework) and the regulatory challenges they pose (such as the tendency of elaborate supply chains to attenuate and fracture statutory responsibilities, at least in terms of the attitudes and behaviour of those involved).

Some major problems with existing models and terminology associated with kimberlite pipes from a volcanological perspective, and some suggestions

Five significant problems hinder advances in understanding of the volcanology of kimberlites: (1) kimberlite geology is very model driven; (2) a highly genetic terminology drives deposit or facies interpretation; (3) the effects of alteration on preserved depositional textures have been grossly underestimated; (4) the level of understanding of the physical process significance of preserved textures is limited; and, (5) some inferred processes and deposits are not based on actual, modern volcanological processes. These issues need to be addressed in order to advance understanding of kimberlite volcanological pipe forming processes and deposits. The traditional, steep-sided southern African pipe model (Class I) consists of a steep tapering pipe with a deep root zone, a middle diatreme zone and an upper crater zone (if preserved). Each zone is thought to be dominated by distinctive facies, respectively: hypabyssal kimberlite (HK, descriptively called here massive coherent porphyritic kimberlite), tuffisitic kimberlite breccia (TKB, descriptively here called massive, poorly sorted lapilli tuff) and crater zone facies, which include variably bedded pyroclastic kimberlite and resedimented and reworked volcaniclastic kimberlite (RVK). Porphyritic coherent kimberlite may, however, also be emplaced at different levels in the pipe, as later stage intrusions, as well as dykes in the surrounding country rock. The relationship between HK and TKB is not always clear. Sub-terranean fluidisation as an emplacement process is a largely unsubstantiated hypothesis; modern in-vent volcanological processes should initially be considered to explain observed deposits. Crater zone volcaniclastic deposits can occur within the diatreme zone of some pipes, indicating that the pipe was largely empty at the end of the eruption, and subsequently began to fill-in largely through resedimentation and sourcing of pyroclastic deposits from nearby vents. Classes II and III Canadian kimberlite models have a more factual, descriptive basis, but are still inadequately documented given the recency of their discovery. The diversity amongst kimberlite bodies suggests that a three-model classification is an over-simplification. Every kimberlite is altered to varying degrees, which is an intrinsic consequence of the ultrabasic composition of kimberlite and the in-vent context; few preserve original textures. The effects of syn- to post-emplacement alteration on original textures have not been adequately considered to date, and should be back-stripped to identify original textural elements and configurations. Applying sedimentological textural configurations as a guide to emplacement processes would be useful. The traditional terminology has many connotations about spatial position in pipe and of process. Perhaps the traditional terminology can be retained in the industrial situation as a general lithofacies-mining terminological scheme because it is so entrenched. However, for research purposes a more descriptive lithofacies terminology should be adopted to facilitate detailed understanding of deposit characteristics, important variations in these, and the process origins. For example every deposit of TKB is different in componentry, texture, or depositional structure. However, because so many deposits in many different pipes are called TKB, there is an implication that they are all similar and that similar processes were involved, which is far from clear.

Genomic architecture of ecologically divergent body shape in a pair of sympatric crater lake cichlid fishes

Determining the genetic bases of adaptations and their roles in speciation is a prominent issue in evolutionary biology. Cichlid fish species flocks are a prime example of recent rapid radiations, often associated with adaptive phenotypic divergence from a common ancestor within a short period of time. In several radiations of freshwater fishes, divergence in ecomorphological traits - including body shape, colour, lips and jaws - is thought to underlie their ecological differentiation, specialization and, ultimately, speciation. The Midas cichlid species complex (Amphilophus spp.) of Nicaragua provides one of the few known examples of sympatric speciation where species have rapidly evolved different but parallel morphologies in young crater lakes. This study identified significant QTL for body shape using SNPs generated via ddRAD sequencing and geometric morphometric analyses of a cross between two ecologically and morphologically divergent, sympatric cichlid species endemic to crater Lake Apoyo: an elongated limnetic species (Amphilophus zaliosus) and a high-bodied benthic species (Amphilophus astorquii). A total of 453 genome-wide informative SNPs were identified in 240 F-2 hybrids. These markers were used to construct a genetic map in which 25 linkage groups were resolved. Seventy-two segregating SNPs were linked to 11 QTL. By annotating the two most highly supported QTL-linked genomic regions, genes that might contribute to divergence in body shape along the benthic-limnetic axis in Midas cichlid sympatric adaptive radiations were identified. These results suggest that few genomic regions of large effect contribute to early stage divergence in Midas cichlids.

Prevalence and risk factors for foot and ankle musculoskeletal disorders experienced by nurses

Background Nurses are at high risk of musculoskeletal disorders (MSDs). Although the prevalence of MSDs of the lower back, upper limbs, neck and shoulders have been reported previously in nursing, few studies have evaluated MSDs of the foot and ankle. This study evaluated the prevalence of foot and ankle MSDs in nurses and their relation to individual and workplace risk factors. Methods A self-administered survey incorporating the Nordic Musculoskeletal Questionnaire (NMQ) was distributed, over a nine-week period, to all eligible nurses (n = 416) working in a paediatric hospital in Brisbane, Australia. The prevalence of MSDs for each of the NMQ body regions was determined. Bivariate and multivariable logistic regression analyses were conducted to examine the relationships between activity-limiting foot/ankle MSDs and risk factors related to the individual (age, body mass index, number of existing foot conditions, smoking history, general physical health [SF36 Physical Component Scale], footwear features) or the workplace (level of nursing position, work location, average hours worked, hours worked in previous week, time since last break from work). Results A 73% response rate was achieved with 304 nurses completing surveys, of whom 276 were females (91%). Mean age of the nurses was 37 years (±10), younger than the state average of 43 years. Foot/ankle MSDs were the most prevalent conditions experienced by nurses during the preceding seven days (43.8%, 95% CI 38.2-49.4%), the second most prevalent MSDs to impair physical activity (16.7%, 95% CI 13.0-21.3%), and the third most prevalent MSD, after lower-back and neck problems, during the preceding 12 months (55.3%, 95% CI 49.6-60.7%). Of the nurse and work characteristics investigated, obesity, poor general physical health, existing foot conditions and working in the intensive care unit emerged as statistically significant (p < 0.05) independent risk factors for activity-limiting foot/ankle MSDs. Conclusions Foot/ankle MSDs are common in paediatric hospital nurses and resulted in physical activity limitations in one out of every six nurses. We recommend targeted education programs regarding the prevention, self-management and treatment strategies for foot/ankle MSDs. Further research is needed into the impact of work location and extended shift durations on foot/ankle MSDs.

IASDR 2015 Interplay Exhibition 2-5 NOV 2015

It has been said that we are living in a golden age of innovation. New products, systems and services aimed to enable a better future, have emerged from novel interconnections between design and design research with science, technology and the arts. These intersections are now, more than ever, catalysts that enrich daily activities for health and safety, education, personal computing, entertainment and sustainability, to name a few. Interactive functions made possible by new materials, technology, and emerging manufacturing solutions demonstrate an ongoing interplay between cross-disciplinary knowledge and research. Such interactive interplay bring up questions concerning: (i) how art and design provide a focus for developing design solutions and research in technology; (ii) how theories emerging from the interactions of cross-disciplinary knowledge inform both the practice and research of design and (iii) how research and design work together in a mutually beneficial way. The IASDR2015 INTERPLAY EXHIBITION provides some examples of these interconnections of design research with science, technology and the arts. This is done through the presentation of objects, artefacts and demonstrations that are contextualised into everyday activities across various areas including health, education, safety, furniture, fashion and wearable design. The exhibits provide a setting to explore the various ways in which design research interacts across discipline knowledge and approaches to stimulate innovation. In education, Designing South African Children’s Health Education as Generative Play (A Bennett, F Cassim, M van der Merwe, K van Zijil, and M Ribbens) presents a set of toolkits that resulted from design research entailing generative play. The toolkits are systems that engender pleasure and responsibility, and are aimed at cultivating South African’s youth awareness of nutrition, hygiene, disease awareness and prevention, and social health. In safety, AVAnav: Avalanche Rescue Helmet (Jason Germany) delivers an interactive system as a tool to contribute to reduce the time to locate buried avalanche victims. Helmet-mounted this system responds to the contextual needs of rescuers and has since led to further design research on the interface design of rescuing devices. In apparel design and manufacturing, Shrinking Violets: Fashion design for disassembly (Alice Payne) proposes a design for disassembly through the use of beautiful reversible mono-material garments that interactively responds to the challenges of garment construction in the fashion industry, capturing the metaphor for the interplay between technology and craft in the fashion manufacturing industry. Harvest: A biotextile future (Dean Brough and Alice Payne), explores the interplay of biotechnology, materiality and textile design in the creation of sustainable, biodegradable vegan textile through the process of a symbiotic culture of bacteria and yeast (SCOBY). SCOBY is a pellicle curd that can be harvested, machine washed, dried and cut into a variety of designs and texture combinations. The exploration of smart materials, wearable design and micro-electronics led to creative and aesthetically coherent stimulus-reactive jewellery; Symbiotic Microcosms: Crafting Digital Interaction (K Vones). This creation aims to bridge the gap between craft practitioner and scientific discovery, proposing a move towards the notion of a post-human body, where wearable design is seen as potential ground for new human-computer interactions, affording the development of visually engaging multifunctional enhancements. In furniture design, Smart Assistive chair for older adults (Chao Zhao) demonstrates how cross-disciplinary knowledge interacting with design strategies provide solution that employed new technological developments in older aged care, and the participation of multiple stakeholders: designers, health care system and community based health systems. In health, Molecular diagnosis system for newborns deafness genetic screening (Chao Zhao) presents an ambitious and complex project that includes a medical device aimed at resolving a number of challenges: technical feasibility for city and rural contexts, compatibility with standard laboratory and hospital systems, access to health system, and support the work of different hospital specialists. The interplay between cross-disciplines is evident in this work, demonstrating how design research moves forward through technology developments. These works exemplify the intersection between domains as a means to innovation. Novel design problems are identified as design intersects with the various areas. Research informs this process, and in different ways. We see the background investigation into the contextualising domain (e.g. on-snow studies, garment recycling, South African health concerns, the post human body) to identify gaps in the area and design criteria; the technologies and materials reviews (e.g. AR, biotextiles) to offer plausible technical means to solve these, as well as design criteria. Theoretical reviews can also inform the design (e.g. play, flow). These work together to equip the design practitioner with a robust set of ‘tools’ for design innovation – tools that are based in research. The process identifies innovative opportunity and criteria for design and this, in turn, provides a means for evaluating the success of the design outcomes. Such an approach has the potential to come full circle between research and design – where the design can function as an exemplar, evidencing how the research-articulated problems can be solved. Core to this, however, is the evaluation of the design outcome itself and identifying knowledge outcomes. In some cases, this is fairly straightforward that is, easily measurable. For example the efficacy of Jason Germany’s helmet can be determined by measuring the reduced response time in the rescuer. Similarly the improved ability to recycle Payne’s panel garments can be clearly determined by comparing it to those recycling processes (and her identified criteria of separating textile elements!); while the sustainability and durability of the Brough & Payne’s biotextile can be assessed by documenting the growth and decay processes, or comparative strength studies. There are however situations where knowledge outcomes and insights are not so easily determined. Many of the works here are open-ended in their nature, as they emphasise the holistic experience of one or more designs, in context: “the end result of the art activity that provides the health benefit or outcome but rather, the value lies in the delivery and experience of the activity” (Bennet et al.) Similarly, reconfiguring layers of laser cut silk in Payne’s Shrinking Violets constitutes a customisable, creative process of clothing oneself since it “could be layered to create multiple visual effects”. Symbiotic Microcosms also has room for facilitating experience, as the work is described to facilitate “serendipitous discovery”. These examples show the diverse emphasis of enquiry as on the experience versus the product. Open-ended experiences are ambiguous, multifaceted and differ from person to person and moment to moment (Eco 1962). Determining the success is not always clear or immediately discernible; it may also not be the most useful question to ask. Rather, research that seeks to understand the nature of the experience afforded by the artefact is most useful in these situations. It can inform the design practitioner by helping them with subsequent re-design as well as potentially being generalizable to other designers and design contexts. Bennett et. al exemplify how this may be approached from a theoretical perspective. This work is concerned with facilitating engaging experiences to educate and, ultimately impact on that community. The research is concerned with the nature of that experience as well, and in order to do so the authors have employed theoretical lenses – here these are of flow, pleasure, play. An alternative or complementary approach to using theory, is using qualitative studies such as interviews with users to ask them about what they experienced? Here the user insights become evidence for generalising across, potentially revealing insight into relevant concerns – such as the range of possible ‘playful’ or experiences that may be afforded, or the situation that preceded a ‘serendipitous discovery’. As shown, IASDR2015 INTERPLAY EXHIBITION provides a platform for exploration, discussion and interrogation around the interplay of design research across diverse domains. We look forward with excitement as IASDR continues to bring research and design together, and as our communities of practitioners continue to push the envelope of what is design and how this can be expanded and better understood with research to foster new work and ultimately, stimulate innovation.