Particle and gaseous emissions from commercial aircraft at each stage of the landing and takeoff cycle

A novel technique was used to measure emission factors for commonly used commercial aircraft including a range of Boeing and Airbus airframes under real world conditions. Engine exhaust emission factors for particles in terms of particle number and mass (PM2.5), along with those for CO2, and NOx were measured for over 280 individual aircraft during the various modes of landing/takeoff (LTO) cycle. Results from this study show that particle number, and NOx emission factors are dependant on aircraft engine thrust level. Minimum and maximum emissions factors for particle number, PM2.5, and NOx emissions were found to be in the range of 4.16×1015-5.42×1016 kg-1, 0.03-0.72 g.kg-1, and 3.25-37.94 g.kg-1 respectively for all measured airframes and LTO cycle modes. Number size distributions of emitted particles for the naturally diluted aircraft plumes in each mode of LTO cycle showed that particles were predominantly in the range of 4 to 100 nm in diameter in all cases. In general, size distributions exhibit similar modality during all phases of the LTO cycle. A very distinct nucleation mode was observed in all particle size distributions, except for taxiing and landing of A320 aircraft. Accumulation modes were also observed in all particle size distributions. Analysis of aircraft engine emissions during LTO cycle showed that aircraft thrust level is considerably higher during taxiing than idling suggesting that International Civil Aviation Organization (ICAO) standards need to be modified as the thrust levels for taxi and idle are considered to be the same (7% of total thrust) [1].

Particle and gaseous emissions from compressed natural gas and ultralow sulphur diesel-fuelled buses at four steady engine loads

Exhaust emissions from thirteen compressed natural gas (CNG) and nine ultralow sulphur diesel in-service transport buses were monitored on a chassis dynamometer. Measurements were carried out at idle and at three steady engine loads of 25%, 50% and 100% of maximum power at a fixed speed of 60 kmph. Emission factors were estimated for particle mass and number, carbon dioxide and oxides of nitrogen for two types of CNG buses (Scania and MAN, compatible with Euro 2 and 3 emission standards, respectively) and two types of diesel buses (Volvo Pre-Euro/Euro1 and Mercedez OC500 Euro3). All emission factors increased with load. The median particle mass emission factor for the CNG buses was less than 1% of that from the diesel buses at all loads. However, the particle number emission factors did not show a statistically significant difference between buses operating on the two types of fuel. In this paper, for the very first time, particle number emission factors are presented at four steady state engine loads for CNG buses. Median values ranged from the order of 1012 particles min-1 at idle to 1015 particles km-1 at full power. Most of the particles observed in the CNG emissions were in the nanoparticle size range and likely to be composed of volatile organic compounds The CO2 emission factors were about 20% to 30% greater for the diesel buses over the CNG buses, while the oxides of nitrogen emission factors did not show any difference due to the large variation between buses.

Long-term trends in fine particle number concentrations in the urban atmosphere of Brisbane : the relevance of traffic emissions and new particle formation

The measurement of submicrometre (< 1.0 m) and ultrafine particles (diameter < 0.1 m) number concentration have attracted attention since the last decade because the potential health impacts associated with exposure to these particles can be more significant than those due to exposure to larger particles. At present, ultrafine particles are not regularly monitored and they are yet to be incorporated into air quality monitoring programs. As a result, very few studies have analysed their long-term and spatial variations in ultrafine particle concentration, and none have been in Australia. To address this gap in scientific knowledge, the aim of this research was to investigate the long-term trends and seasonal variations in particle number concentrations in Brisbane, Australia. Data collected over a five-year period were analysed using weighted regression models. Monthly mean concentrations in the morning (6:00-10:00) and the afternoon (16:00-19:00) were plotted against time in months, using the monthly variance as the weights. During the five-year period, submicrometre and ultrafine particle concentrations increased in the morning by 105.7% and 81.5% respectively whereas in the afternoon there was no significant trend. The morning concentrations were associated with fresh traffic emissions and the afternoon concentrations with the background. The statistical tests applied to the seasonal models, on the other hand, indicated that there was no seasonal component. The spatial variation in size distribution in a large urban area was investigated using particle number size distribution data collected at nine different locations during different campaigns. The size distributions were represented by the modal structures and cumulative size distributions. Particle number peaked at around 30 nm, except at an isolated site dominated by diesel trucks, where the particle number peaked at around 60 nm. It was found that ultrafine particles contributed to 82%-90% of the total particle number. At the sites dominated by petrol vehicles, nanoparticles (< 50 nm) contributed 60%-70% of the total particle number, and at the site dominated by diesel trucks they contributed 50%. Although the sampling campaigns took place during different seasons and were of varying duration these variations did not have an effect on the particle size distributions. The results suggested that the distributions were rather affected by differences in traffic composition and distance to the road. To investigate the occurrence of nucleation events, that is, secondary particle formation from gaseous precursors, particle size distribution data collected over a 13 month period during 5 different campaigns were analysed. The study area was a complex urban environment influenced by anthropogenic and natural sources. The study introduced a new application of time series differencing for the identification of nucleation events. To evaluate the conditions favourable to nucleation, the meteorological conditions and gaseous concentrations prior to and during nucleation events were recorded. Gaseous concentrations did not exhibit a clear pattern of change in concentration. It was also found that nucleation was associated with sea breeze and long-range transport. The implications of this finding are that whilst vehicles are the most important source of ultrafine particles, sea breeze and aged gaseous emissions play a more important role in secondary particle formation in the study area.

Construction defect reporting using mobile and digital workbench technologies

Sending data between the construction site and an off-site design office is one of the more problematic areas in information technology for construction automation, particularly for construction defect management. The aim of this research is to investigate how mobile computing and new forms of human-computer interaction can be brought to bear on specific problems in construction management. The construction defect reporting system is one such application. Combining mobile and wireless computing technologies with a digital workbench, we have developed a system to facilitate remote telecollaboration between a construction site and an off-site engineering office. The application reported in this paper demonstrates how construction defect reporting can be streamlined by field collection of construction defect information using a mobile device and visualising the defect in a CAD model on a digital workbench in an engineering office. This paper reports on the design of the system and our tests of sending images from the construction site to the engineer’s office and positional accuracy of GPS for localization of the defect.

Citizen journalism as social networking : reporting the 2007 Australian Federal Election

One of the perceived Achilles heels of online citizen journalism is its perceived inability to conduct investigative and first-hand reporting. A number of projects have recently addressed this problem, with varying success: the U.S.-based Assignment Zero was described as "a highly satisfying failure" (Howe 2007), while the German MyHeimat.de appears to have been thoroughly successful in attracting a strong community of contributors, even to the point of being able to generate print versions of its content, distributed free of charge to households in selected German cities. In Australia, citizen journalism played a prominent part in covering the federal elections held on 24 November 2007; news bloggers and public opinion Websites provided a strong counterpoint to the mainstream media coverage of the election campaign (Bruns et al., 2007). Youdecide2007.org, a collaboration between researchers at Queensland University of Technology and media practitioners at the public service broadcaster SBS, the public opinion site On Line Opinion, and technology company Cisco Systems, was developed as a dedicated space for a specifically hyperlocal coverage of the election campaign in each of Australia's 150 electorates from the urban sprawls of Sydney and Brisbane to the sparsely populated remote regions of outback Australia. YD07 provided training materials for would-be citizen journalists and encouraged them to contribute electorate profiles, interview candidates, and conduct vox-pops with citizens in their local area. The site developed a strong following especially in its home state of Queensland, and its interviewers influenced national public debate by uncovering the sometimes controversial personal views of mainstream and fringe candidates. At the same time, the success of YD07 was limited by external constraints determined by campaign timing and institutional frameworks. As part of a continuing action research cycle, lessons learnt from Youdecide2007.org are going to be translated into further iterations of the project, which will cover the local government elections in the Australian state of Queensland, to be held in March 2008, and developments subsequent to these elections. This paper will present research outcomes from the Youdecide2007.org project. In particular, it will examine the roles of staff contributors and citizen journalists in attracting members, providing information, promoting discussion, and fostering community on the site: early indications from a study of interaction data on the site indicate notably different contribution patterns and effects for staff and citizen participants, which may point towards the possibility of developing more explicit pro-am collaboration models in line with the Pro-Am phenomenon outlined by Leadbeater & Miller (2004). The paper will outline strengths and weaknesses of the Youdecide model and highlight requirements for the successful development of active citizen journalism communities. In doing so, it will also evaluate the feasibility of hyperlocal citizen journalism approaches, and their interrelationship with broader regional, state, and national journalism in both its citizen and industrial forms.

Development of a particle number and particle mass vehicle emissions inventory for an urban fleet

Motor vehicles are major emitters of gaseous and particulate pollution in urban areas, and exposure to particulate pollution can have serious health effects, ranging from respiratory and cardiovascular disease to mortality. Motor vehicle tailpipe particle emissions span a broad size range from 0.003-10µm, and are measured as different subsets of particle mass concentrations or particle number count. However, no comprehensive inventories currently exist in the international published literature covering this wide size range. This paper presents the first published comprehensive inventory of motor vehicle tailpipe particle emissions covering the full size range of particles emitted. The inventory was developed for urban South-East Queensland by combining two techniques from distinctly different disciplines, from aerosol science and transport modelling. A comprehensive set of particle emission factors were combined with traffic modelling, and tailpipe particle emissions were quantified for particle number (ultrafine particles), PM1, PM2.5 and PM10 for light and heavy duty vehicles and buses. A second aim of the paper involved using the data derived in this inventory for scenario analyses, to model the particle emission implications of different proportions of passengers travelling in light duty vehicles and buses in the study region, and to derive an estimate of fleet particle emissions in 2026. It was found that heavy duty vehicles (HDVs) in the study region were major emitters of particulate matter pollution, and although they contributed only around 6% of total regional vehicle kilometres travelled, they contributed more than 50% of the region’s particle number (ultrafine particles) and PM1 emissions. With the freight task in the region predicted to double over the next 20 years, this suggests that HDVs need to be a major focus of mitigation efforts. HDVs dominated particle number (ultrafine particles) and PM1 emissions; and LDV PM2.5 and PM10 emissions. Buses contributed approximately 1-2% of regional particle emissions.

Increase in particle number emissions from motor vehicles due to interruption of steady traffic flow

We assess the increase in particle number emissions from motor vehicles driving at steady speed when forced to stop and accelerate from rest. Considering the example of a signalized pedestrian crossing on a two-way single-lane urban road, we use a complex line source method to calculate the total emissions produced by a specific number and mix of light petrol cars and diesel passenger buses and show that the total emissions during a red light is significantly higher than during the time when the light remains green. Replacing two cars with one bus increased the emissions by over an order of magnitude. Considering these large differences, we conclude that the importance attached to particle number emissions in traffic management policies be reassessed in the future.

Differential reporting and the effect on loan evaluations : an experimental study

This study utilises a mexed design laboratory experiment to test the impact of differential reporting on one group of external financial report users-lenders. The results indicate that the judgments of bank loan officers' assessment of the ability of a borrower to repay, are not significantly affected by differential reporting (in this case, presentation on non-GAAP financial reports compared to GAAP financial reports). However, bankers request additional information from borrowers when non-GAAP financial reports are presented.

Teacher Reporting Questionnaire - Western Australia Government Schools

This instrument was used in the project named Teachers Reporting Child Sexual Abuse: Towards Evidence-based Reform of Law, Policy and Practice (ARC DP0664847)

Teacher Reporting Questionnaire : Western Australia Non-Government Schools

This instrument was used in the project named Teachers Reporting Child Sexual Abuse: Towards Evidence-based Reform of Law, Policy and Practice (ARC DP0664847)

Teachers reporting suspected child sexual abuse : results of a three-state study

Over 3000 cases of child sexual abuse are identified every year in Australia, but the real incidence is higher still. As a strategy to identify child sexual abuse, Australian States and Territories have enacted legislation requiring members of selected professions, including teachers, to report suspected cases. In addition, policy-based reporting obligations have been developed by professions, including the teaching profession. These legislative and industry-based developments have occurred in a context of growing awareness of the incidence and consequences of child sexual abuse. Teachers have frequent contact and close relationships with children, and possess expertise in monitoring changes in children’s behaviour. Accordingly, teachers are seen as being well-placed to detect and report suspected child sexual abuse. To date, however, there has been little empirical research into the operation of these reporting duties. The extent of teachers’ awareness of their duties to report child sexual abuse is unknown. Further, there is little evidence about teachers’ past reporting practice. Teachers’ duties to report sexual abuse, especially those in legislation, differ between States, and it is not known whether or how these differences affect reporting practice. This article presents results from the first large-scale Australian survey of teachers in three States with different reporting laws: New South Wales, Queensland, and Western Australia. The results indicate levels of teacher knowledge of reporting duties, reveal evidence about past reporting practice, and provide insights into anticipated future reporting practice and legal compliance. The findings have implications for reform of legislation and policy, training of teachers about the reporting of child sexual abuse, and enhancement of child protection.

Investigation into submicrometer particle and gaseous emissions from airport ground running procedures

Emissions from airport operations are of significant concern because of their potential impact on local air quality and human health. The currently limited scientific knowledge of aircraft emissions is an important issue worldwide, when considering air pollution associated with airport operation, and this is especially so for ultrafine particles. This limited knowledge is due to scientific complexities associated with measuring aircraft emissions during normal operations on the ground. In particular this type of research has required the development of novel sampling techniques which must take into account aircraft plume dispersion and dilution as well as the various particle dynamics that can affect the measurements of the aircraft engine plume from an operational aircraft. In order to address this scientific problem, a novel mobile emission measurement method called the Plume Capture and Analysis System (PCAS), was developed and tested. The PCAS permits the capture and analysis of aircraft exhaust during ground level operations including landing, taxiing, takeoff and idle. The PCAS uses a sampling bag to temporarily store a sample, providing sufficient time to utilize sensitive but slow instrumental techniques to be employed to measure gas and particle emissions simultaneously and to record detailed particle size distributions. The challenges in relation to the development of the technique include complexities associated with the assessment of the various particle loss and deposition mechanisms which are active during storage in the PCAS. Laboratory based assessment of the method showed that the bag sampling technique can be used to accurately measure particle emissions (e.g. particle number, mass and size distribution) from a moving aircraft or vehicle. Further assessment of the sensitivity of PCAS results to distance from the source and plume concentration was conducted in the airfield with taxiing aircraft. The results showed that the PCAS is a robust method capable of capturing the plume in only 10 seconds. The PCAS is able to account for aircraft plume dispersion and dilution at distances of 60 to 180 meters downwind of moving a aircraft along with particle deposition loss mechanisms during the measurements. Characterization of the plume in terms of particle number, mass (PM2.5), gaseous emissions and particle size distribution takes only 5 minutes allowing large numbers of tests to be completed in a short time. The results were broadly consistent and compared well with the available data. Comprehensive measurements and analyses of the aircraft plumes during various modes of the landing and takeoff (LTO) cycle (e.g. idle, taxi, landing and takeoff) were conducted at Brisbane Airport (BNE). Gaseous (NOx, CO2) emission factors, particle number and mass (PM2.5) emission factors and size distributions were determined for a range of Boeing and Airbus aircraft, as a function of aircraft type and engine thrust level. The scientific complexities including the analysis of the often multimodal particle size distributions to describe the contributions of different particle source processes during the various stages of aircraft operation were addressed through comprehensive data analysis and interpretation. The measurement results were used to develop an inventory of aircraft emissions at BNE, including all modes of the aircraft LTO cycle and ground running procedures (GRP). Measurements of the actual duration of aircraft activity in each mode of operation (time-in-mode) and compiling a comprehensive matrix of gas and particle emission rates as a function of aircraft type and engine thrust level for real world situations was crucial for developing the inventory. The significance of the resulting matrix of emission rates in this study lies in the estimate it provides of the annual particle emissions due to aircraft operations, especially in terms of particle number. In summary, this PhD thesis presents for the first time a comprehensive study of the particle and NOx emission factors and rates along with the particle size distributions from aircraft operations and provides a basis for estimating such emissions at other airports. This is a significant addition to the scientific knowledge in terms of particle emissions from aircraft operations, since the standard particle number emissions rates are not currently available for aircraft activities.

Patterns of reporting to child protection services in Canada by healthcare and nonhealthcare professionals

Background: All Canadian jurisdictions require certain professionals to report suspected or observed child maltreatment. This study examined the types of maltreatment, level of harm and child functioning issues, controlling for family socioeconomic status, age and gender of the child reported by healthcare and non-healthcare professionals. Methods: We conducted chi-square analyses and logistic regression on a national child welfare sample from the 2003 Canadian Incidence Study of Reported Child Abuse and Neglect (CIS-2003) and compared the differences in professional reporting with its previous cycle (CIS-1998) using Bonferroni-corrected confidence intervals. Results: Our analysis of CIS-2003 data revealed that the majority of substantiated child maltreatment is reported to service agencies by non-healthcare professionals (57%), followed by non-professionals (33%) and healthcare professionals (10%). The number of professional reports increased 2.5 times between CIS-1998 and CIS-2003, while non-professionals’ increased 1.7 times. Of the total investigations, professional reports represented 59% in CIS-1998 and 67% in CIS-2003 (p<0.001). Compared to non-healthcare professionals, healthcare professionals more often reported younger children, children who experienced neglect and emotional maltreatment and those assessed as suffering harm and child functioning issues, but less often exposure to domestic violence. Conclusion: The results indicate that healthcare professionals played an important role in identifying children in need of protection considering harm and other child functioning issues. The authors discuss the reasons why underreporting is likely to remain an issue.

Particle emissions, volatility, and toxicity from an ethanol fumigated compression ignition engine

Particle emissions, volatility, and the concentration of reactive oxygen species (ROS) were investigated for a pre-Euro I compression ignition engine to study the potential health impacts of employing ethanol fumigation technology. Engine testing was performed in two separate experimental campaigns with most testing performed at intermediate speed with four different load settings and various ethanol substitutions. A scanning mobility particle sizer (SMPS) was used to determine particle size distributions, a volatilization tandem differential mobility analyzer (V-TDMA) was used to explore particle volatility, and a new profluorescent nitroxide probe, BPEAnit, was used to investigate the potential toxicity of particles. The greatest particulate mass reduction was achieved with ethanol fumigation at full load, which contributed to the formation of a nucleation mode. Ethanol fumigation increased the volatility of particles by coating the particles with organic material or by making extra organic material available as an external mixture. In addition, the particle-related ROS concentrations increased with ethanol fumigation and were associated with the formation of a nucleation mode. The smaller particles, the increased volatility, and the increase in potential particle toxicity with ethanol fumigation may provide a substantial barrier for the uptake of fumigation technology using ethanol as a supplementary fuel.