Solid-state nanocrystalline dye-sensitized solar cell using 2-mercapto benzimidazole doped poly(ethylene oxide) as a new polymer electrolyte

New composite doped poly (ethylene oxide) polymer electrolyte was developed using 2-mercapto benzimidazole as plasticizer and iodide/triiodide as redox couple. The fabrication of the cell involves Poly(ethylene oxide)/ 2-mercapto benzimidazole / iodide/triiodide as polymer electrolyte in dye-sensitized solar cell fabricated with N3 dye and TiO2 nanoparticles as the photoanode and Platinum coated FTO (fluorine doped SnO2) as counter electrode. The current-volatage characteristics under simulated sunlight AM1.5 shows a short circuit current Isc of 8.7mA and open circuit photovoltage 508 mV. The conductivity measurements for the new polymer electrolyte and the photoelectrochemical measurments were carried out systematically. In 2-mercapto benzimidazole the electron rich sulphur and nitrogen atoms, act as pi-electron donors that form good interaction with iodine which plays a vital role in the performance of the fabricated dye-sensitized solar cells. The resonance effect increases the stability of the cell to a considerable extent. These results suggest that the new composite polymer electrolyte performs as a promising new doped polymer-electrolyte.

Kinetics of electron recombination of dye-senitized solar cells based on TiO2 nanorod arrays sensitized with different dyes

The performance and electron recombination kinetics of dye-sensitized solar cells based on TiO2 films consisting of one-dimensional nanorod arrays (NR-DSSCs) which are sensitized with dye N719, C218 and D205 respectively have been studied. It has been found that the best efficiency is obtained with the dye C218 based NR-DSSCs, benefiting from a 40% higher short-circuit photocurrent density. However, the open circuit photovoltage of the N719 based cell is 40 mV higher than that of the organic dye C218 and D205 based devices. Investigation of the electron recombination kinetics of the NR-DSSCs has revealed that the effective electron lifetime, τn, of the N719 based NR-DSSC is the lowest whereas the τn of the C218 based NR-DSSC is the highest among the three dyes. The higher Voc with the N719 based NR-DSSC is originated from the more negative energy level of the conduction band of the TiO2 film. In addition, in comparison to the DSSCs with conventional nanocrystalline particles based TiO2 films, the NR-DSSCs have shown over two orders of magnitude higher τn when employing N719 as the sensitizer. Nevertheless, the τn of the DSSCs with the C218 based nanorod arrays is only ten-fold higher than the that of the nanoparticles based devices. The remarkable characteristic of the dye C218 in suppressing the electron recombination of DSSCs is discussed.

Malnutrition in Parkinson's disease and an individualised approach to its management

It has been reported that poor nutritional status, in the form of weight loss and resulting body mass index (BMI) changes, is an issue in people with Parkinson's disease (PWP). The symptoms resulting from Parkinson's disease (PD) and the side effects of PD medication have been implicated in the aetiology of nutritional decline. However, the evidence on which these claims are based is, on one hand, contradictory, and on the other, restricted primarily to otherwise healthy PWP. Despite the claims that PWP suffer from poor nutritional status, evidence is lacking to inform nutrition-related care for the management of malnutrition in PWP. The aims of this thesis were to better quantify the extent of poor nutritional status in PWP, determine the important factors differentiating the well-nourished from the malnourished and evaluate the effectiveness of an individualised nutrition intervention on nutritional status. Phase DBS: Nutritional status in people with Parkinson's disease scheduled for deep-brain stimulation surgery The pre-operative rate of malnutrition in a convenience sample of people with Parkinson's disease (PWP) scheduled for deep-brain stimulation (DBS) surgery was determined. Poorly controlled PD symptoms may result in a higher risk of malnutrition in this sub-group of PWP. Fifteen patients (11 male, median age 68.0 (42.0 – 78.0) years, median PD duration 6.75 (0.5 – 24.0) years) participated and data were collected during hospital admission for the DBS surgery. The scored PG-SGA was used to assess nutritional status, anthropometric measures (weight, height, mid-arm circumference, waist circumference, body mass index (BMI)) were taken, and body composition was measured using bioelectrical impedance spectroscopy (BIS). Six (40%) of the participants were malnourished (SGA-B) while 53% reported significant weight loss following diagnosis. BMI was significantly different between SGA-A and SGA-B (25.6 vs 23.0kg/m 2, p<.05). There were no differences in any other variables, including PG-SGA score and the presence of non-motor symptoms. The conclusion was that malnutrition in this group is higher than that in other studies reporting malnutrition in PWP, and it is under-recognised. As poorer surgical outcomes are associated with poorer pre-operative nutritional status in other surgeries, it might be beneficial to identify patients at nutritional risk prior to surgery so that appropriate nutrition interventions can be implemented. Phase I: Nutritional status in community-dwelling adults with Parkinson's disease The rate of malnutrition in community-dwelling adults (>18 years) with Parkinson's disease was determined. One hundred twenty-five PWP (74 male, median age 70.0 (35.0 – 92.0) years, median PD duration 6.0 (0.0 – 31.0) years) participated. The scored PG-SGA was used to assess nutritional status, anthropometric measures (weight, height, mid-arm circumference (MAC), calf circumference, waist circumference, body mass index (BMI)) were taken. Nineteen (15%) of the participants were malnourished (SGA-B). All anthropometric indices were significantly different between SGA-A and SGA-B (BMI 25.9 vs 20.0kg/m2; MAC 29.1 – 25.5cm; waist circumference 95.5 vs 82.5cm; calf circumference 36.5 vs 32.5cm; all p<.05). The PG-SGA score was also significantly lower in the malnourished (2 vs 8, p<.05). The nutrition impact symptoms which differentiated between well-nourished and malnourished were no appetite, constipation, diarrhoea, problems swallowing and feel full quickly. This study concluded that malnutrition in community-dwelling PWP is higher than that documented in community-dwelling elderly (2 – 11%), yet is likely to be under-recognised. Nutrition impact symptoms play a role in reduced intake. Appropriate screening and referral processes should be established for early detection of those at risk. Phase I: Nutrition assessment tools in people with Parkinson's disease There are a number of validated and reliable nutrition screening and assessment tools available for use. None of these tools have been evaluated in PWP. In the sample described above, the use of the World Health Organisation (WHO) cut-off (≤18.5kg/m2), age-specific BMI cut-offs (≤18.5kg/m2 for under 65 years, ≤23.5kg/m2 for 65 years and older) and the revised Mini-Nutritional Assessment short form (MNA-SF) were evaluated as nutrition screening tools. The PG-SGA (including the SGA classification) and the MNA full form were evaluated as nutrition assessment tools using the SGA classification as the gold standard. For screening, the MNA-SF performed the best with sensitivity (Sn) of 94.7% and specificity (Sp) of 78.3%. For assessment, the PG-SGA with a cut-off score of 4 (Sn 100%, Sp 69.8%) performed better than the MNA (Sn 84.2%, Sp 87.7%). As the MNA has been recommended more for use as a nutrition screening tool, the MNA-SF might be more appropriate and take less time to complete. The PG-SGA might be useful to inform and monitor nutrition interventions. Phase I: Predictors of poor nutritional status in people with Parkinson's disease A number of assessments were conducted as part of the Phase I research, including those for the severity of PD motor symptoms, cognitive function, depression, anxiety, non-motor symptoms, constipation, freezing of gait and the ability to carry out activities of daily living. A higher score in all of these assessments indicates greater impairment. In addition, information about medical conditions, medications, age, age at PD diagnosis and living situation was collected. These were compared between those classified as SGA-A and as SGA-B. Regression analysis was used to identify which factors were predictive of malnutrition (SGA-B). Differences between the groups included disease severity (4% more severe SGA-A vs 21% SGA-B, p<.05), activities of daily living score (13 SGA-A vs 18 SGA-B, p<.05), depressive symptom score (8 SGA-A vs 14 SGA-B, p<.05) and gastrointestinal symptoms (4 SGA-A vs 6 SGA-B, p<.05). Significant predictors of malnutrition according to SGA were age at diagnosis (OR 1.09, 95% CI 1.01 – 1.18), amount of dopaminergic medication per kg body weight (mg/kg) (OR 1.17, 95% CI 1.04 – 1.31), more severe motor symptoms (OR 1.10, 95% CI 1.02 – 1.19), less anxiety (OR 0.90, 95% CI 0.82 – 0.98) and more depressive symptoms (OR 1.23, 95% CI 1.07 – 1.41). Significant predictors of a higher PG-SGA score included living alone (β=0.14, 95% CI 0.01 – 0.26), more depressive symptoms (β=0.02, 95% CI 0.01 – 0.02) and more severe motor symptoms (OR 0.01, 95% CI 0.01 – 0.02). More severe disease is associated with malnutrition, and this may be compounded by lack of social support. Phase II: Nutrition intervention Nineteen of the people identified in Phase I as requiring nutrition support were included in Phase II, in which a nutrition intervention was conducted. Nine participants were in the standard care group (SC), which received an information sheet only, and the other 10 participants were in the intervention group (INT), which received individualised nutrition information and weekly follow-up. INT gained 2.2% of starting body weight over the 12 week intervention period resulting in significant increases in weight, BMI, mid-arm circumference and waist circumference. The SC group gained 1% of starting weight over the 12 weeks which did not result in any significant changes in anthropometric indices. Energy and protein intake (18.3kJ/kg vs 3.8kJ/kg and 0.3g/kg vs 0.15g/kg) increased in both groups. The increase in protein intake was only significant in the SC group. The changes in intake, when compared between the groups, were no different. There were no significant changes in any motor or non-motor symptoms or in "off" times or dyskinesias in either group. Aspects of quality of life improved over the 12 weeks as well, especially emotional well-being. This thesis makes a significant contribution to the evidence base for the presence of malnutrition in Parkinson's disease as well as for the identification of those who would potentially benefit from nutrition screening and assessment. The nutrition intervention demonstrated that a traditional high protein, high energy approach to the management of malnutrition resulted in improved nutritional status and anthropometric indices with no effect on the presence of Parkinson's disease symptoms and a positive effect on quality of life.

Charge transport studies in donor-acceptor block copolymer PDPP-TNT and PC71BM based inverted organic photovoltaic devices processed in room conditions

Diketopyrrolopyrole-naphthalene polymer (PDPP-TNT), a donor-acceptor co-polymer, has shown versatile behavior demonstrating high performances in organic field-effect transistors (OFETs) and organic photovoltaic (OPV) devices. In this paper we report investigation of charge carrier dynamics in PDPP-TNT, and [6,6]-phenyl C71 butyric acid methyl ester (PC71BM) bulk-heterojunction based inverted OPV devices using current density-voltage (J-V) characteristics, space charge limited current (SCLC) measurements, capacitance-voltage (C-V) characteristics, and impedance spectroscopy (IS). OPV devices in inverted architecture, ITO/ZnO/PDPP-TNT:PC71BM/MoO3/Ag, are processed and characterized at room conditions. The power conversion efficiency (PCE) of these devices are measured ∼3.8%, with reasonably good fill-factor 54.6%. The analysis of impedance spectra exhibits electron’s mobility ∼2 × 10−3 cm2V−1s−1, and lifetime in the range of 0.03-0.23 ms. SCLC measurements give hole mobility of 1.12 × 10−5 cm2V−1s−1, and electron mobility of 8.7 × 10−4 cm2V−1s−1.

Direct electrochemical formation of alloyed AuPt nanostructured electrocatalysts for the oxidation of formic acid

The formation of highly anisotropic AuPt alloys has been achieved via a simple electrochemical approach without the need for organic surfactants to direct the growth process. The surface and bulk properties of these materials were characterised by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX) and electrochemically by cyclic voltammetry to confirm alloy formation. It was found that AuPt materials are highly active for both the model hydrogen evolution reaction and the fuel cell relevant formic acid oxidation reaction. In particular for the latter case the preferred dehydrogenation pathway was observed at AuPt compared to nanostructured Pt prepared under identical electrochemical conditions which demonstrated the less preferred dehydration pathway. The enhanced performance is attributed to both the ensemble effect which facilitates CO(ads) removal from the surface as well as the highly anisotropic nanostructure of AuPt.

Electrochemical formation of Cu/Ag surfaces and their applicability as heterogeneous catalysts

In this work the electrochemical formation of porous Cu/Ag materials is reported via the simple and quick method of hydrogen bubble templating. The bulk and surface composition ratio between Ag and Cu was varied in a systematic manner and was readily controlled by the concentration of precursor metal salts in the electrolyte. The incorporation of Ag within the Cu scaffold only affected the formation of well-defined pores at high Ag loading whereas the internal pore wall structure gradually transformed from dendritic to cube like and finally needle like structures, which was due to the concomitant formation of Cu2O within the structure. The materials were characterised by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Their surface properties were further investigated by surface enhanced Raman spectroscopy (SERS) and electrochemically probed by recording the hydrogen evolution reaction (HER) which is highly sensitive to the nature of the surface. The effect of surface composition was then investigated for its influence on two catalytic reactions namely the reduction of ferricyanide ions with thiosulphate ions and the reduction of 4-nitrophenol with NaBH4 in aqueous solution where it was found that the presence of Ag had a beneficial effect in both cases but more so in the case of nitrophenol reduction. It is believed that this material may have many more potential applications in the area of catalysis, electrocatalysis and photocatalysis.

Electrochemical and spectral studies of self-assembled monolayer of 1,8,15,22-tetraaminophthalocyanatocobalt(II) on indium tin oxide surface

Self-assembled monolayer (SAM) of 1,8,15,22-tetraaminophthalocyanatocobalt(II) (4α-CoIITAPc) was prepared on indium tin oxide (ITO) electrode by spontaneous adsorption from dimethylformamide (DMF) solution containing 4α-CoIITAPc. The SAM of 4α-CoIITAPc formed on ITO electrode was characterized by cyclic voltammetry, Raman and UV–visible spectroscopic techniques. The cyclic voltammogram (CV) of 4α-CoIITAPc SAM shows two pairs of well-defined redox peaks corresponding to CoIII/CoII and CoIIIPc−1/CoIIIPc−2. The surface coverage (Γ) was calculated by integrating the charge under the anodic wave corresponding to CoII oxidation and it was found to be 2.25 × 10−10 mol cm−2. Raman spectrum obtained for the SAM of 4α-CoIITAPc on ITO surface shows strong stretching and breathing bands of Pc macrocycle, pyrrole ring and isoindole ring. Further, the –NH2 bending mode of vibration was absent for the SAM of 4α-CoIITAPc on ITO surface which indirectly confirmed that all the amino groups of 4α-CoIITAPc are involved in bonding with ITO surface. UV–visible spectrum for the SAM of 4α-CoIITAPc on ITO surface shows an intense B-band, Q-band and n–π∗ transition with slight broadening when compared to that of 4α-CoIITAPc in DMF.

Effect of hydrodynamics and surface roughness on the electrochemical behaviour of carbon steel in CSG produced water

The influence of fluid flow, surface roughness and immersion time on the electrochemical behaviour of carbon steel in coal seam gas produced water under static and hydrodynamic conditions has been studied. The disc electrode surface morphology before and after the corrosion test was characterized using scanning electron microscopy (SEM). The corrosion product was examined using X-ray photoelectron spectroscopy (XPS) and X-ray diffractometry (XRD).The results show that the anodic current density increased with increasing surface roughness and consequently a decrease in corrosion surface resistance. Under dynamic flow conditions, the corrosion rate increased with increasing rotating speed due to the high mass transfer coefficient and formation of non-protective akaganeite β- FeO(OH) and goethite α- FeO(OH) corrosion scale at the electrode surface.The corrosion rate was lowest at 0 rpm.The corrosion rate decreased in both static and dynamic conditions with increasing immersion time. The decrease in corrosion rate is attributed to the deposition of corrosion products on the electrode surface. SEM results revealed that the rougher surface exhibited a great tendency toward pitting corrosion.