Fuel consumption and gas emissions of an automatic transmission vehicle following simple eco-driving instructions on urban roads

Following eco-driving instructions can reduce fuel consumption between 5 to 20% on urban roads with manual cars. The majority of Australian cars have an automatic transmission gear-box. It is therefore of interest to verify whether current eco-driving instructions are e cient for such vehicles. In this pilot study, participants (N=13) drove an instrumented vehicle (Toyota Camry 2007) with an automatic transmission. Fuel consumption of the participants was compared before and after they received simple eco-driving instructions. Participants drove the same vehicle on the same urban route under similar tra c conditions. We found that participants drove at similar speeds during their baseline and eco-friendly drives, and reduced the level of their accelerations and decelerations during eco-driving. Fuel consumption decreased for the complete drive by 7%, but not on the motorway and inclined sections of the study. Gas emissions were estimated with the VT-micro model, and emissions of the studied pollutants (CO2, CO, NOX and HC) were reduced, but no di erence was observed for CO2 on the motorway and inclined sections. The di erence for the complete lap is 3% for CO2. We have found evidence showing that simple eco-driving instructions are e cient in the case of automatic transmission in an urban environment, but towards the lowest values of the spectrum of fuel consumption reduction from the di erent eco-driving studies.

The effect of varied test instructions on neuropsychological performance following mild traumatic brain injury : an investigation of ‘diagnosis threat’

Diagnosis threat is a psychosocial factor that has been proposed to contribute to poor outcomes following mild traumatic brain injury (mTBI). This threat is thought to impair the cognitive test performance of individuals with mTBI because of negative injury stereotypes. University students (N= 45, 62.2% female) with a history of mTBI were randomly allocated to a diagnosis threat (DT, n=15), reduced threat (DT-reduced, n=15) or neutral (n=15) group. The reduced threat condition invoked a positive stereotype (i.e., that people with mTBI can perform well on cognitive tests). All participants were given neutral instructions before they completed baseline tests of: a) objective cognitive function across a number of domains; b) psychological symptoms; and, c) PCS symptoms, including self-reported cognitive and emotional difficulties. Participants then received either neutral, DT or DT-reduced instructions, before repeating the tests. Results were analyzed using separate mixed model ANOVAs; one for each dependent measure. The only significant result was for the 2 X 3 ANOVA on an objective test of attention/working memory, Digit Span, p<.05, such that the DT-reduced group performed better than the other groups, which were not different from each other. Although not consistent with predictions or earlier DT studies, the absence of group differences on most tests fits with several recent DT findings. The results of this study suggest that it is timely to reconsider the role of DT as a unique contributor to poor mTBI outcome.

Software watermarking resilient to debugging attacks

In 2006, Gaurav Gupta and Josef Pieprzyk presented an attack on the branch-based software watermarking scheme proposed by Ginger Myles and Hongxia Jin in 2005. The software watermarking model is based on replacing jump instructions or unconditional branch statements (UBS) by calls to a fingerprint branch function (FBF) that computes the correct target address of the UBS as a function of the generated fingerprint and integrity check. If the program is tampered with, the fingerprint and/or integrity checks change and the target address is not computed correctly. Gupta and Pieprzyk's attack uses debugger capabilities such as register and address lookup and breakpoints to minimize the requirement to manually inspect the software. Using these resources, the FBF and calls to the same is identified, correct displacement values are generated and calls to FBF are replaced by the original UBS transferring control of the attack to the correct target instruction. In this paper, we propose a watermarking model that provides security against such debugging attacks. Two primary measures taken are shifting the stack pointer modification operation from the FBF to the individual UBSs, and coding the stack pointer modification in the same language as that of the rest of the code rather than assembly language to avoid conspicuous contents. The manual component complexity increases from O(1) in the previous scheme to O(n) in our proposed scheme.

Deathbed instructions and the assessment of capacity: A practical perspective

The assessment of capacity in the context of wills and advance care planning is a challenging task for modern practitioners with the increase in mentally disabling conditions, such as acquired brain injury. This challenge is only heightened in the situation where the assessment occurs at the client’s deathbed as there are the added elements of urgency, and emotional upheaval at the impending death of a loved one. This situation poses a minefield of problems a legal practitioner should be aware of, involving not only the assessment process but also potential professional liability issues. This presentation will address the practical considerations a legal professional should take into account when in this situation. We will focus on two discrete situations and the issues arising from them: first, where there has been an acquired brain injury and legal capacity is in question; and second, where a spinal injury has occurred which does not affect capacity, rather results in the inability to use conventional forms of communication to communicate his/her instructions. We will examine these case studies with a view to proposing a best practice model for legal practitioners when assessing capacity in this context.

Effectiveness of on-line resources to enhance student learning and engagement

BACKGROUND For engineering graduates to be work-ready with marketable skills they must not only be well-versed with engineering science and its applications, but also able to adapt to using commercial software that is widely used in engineering practice. Hydrological/hydraulic modelling is one aspect of engineering practice which demands the ability to apply fundamentals into design and construction using software. The user manuals for such software are usually tailored for the experienced engineer but not for undergraduates who typically are novices to concepts of modelling and software tools. As the focus of a course such as Advanced Water Engineering is on the wider aspects of engineering application of hydrological and hydraulic concepts, it is ineffective for the lecturers to direct the students to user manuals as students have neither the time nor the desire to sift through numerous pages in a manual. An alternative and efficient way to demonstrate the use of the software is enabling students to develop a model to simulate real-world scenario using the tools of the software and directing them to make informed decisions based on outcomes. PURPOSE Past experience of the lecturer showed that the resources available for the students left a knowledge gap leading to numerous student queries outside contact hours. The purpose of this study is to assess how effective purpose-built video resources can be in supplementing the traditional learning resources to enhance student learning. APPROACH Short-length animated video clips comprising guided step-by-step instructions were prepared using screen capture software to capture screen activity and later edited to focus on specific features using pop-up annotations; Vocal narration was purposely excluded to avoid disturbances due to noise and allow different learning paces of individual students. The video clips were made available to the students alongside the traditional resources/approaches such as in-class demonstrations, guideline notes, and tips for efficient and error-free procedural descriptions. The number of queries the lecturer received from the student cohort outside the lecture times was recorded. An anonymous survey to assess the usefulness and adequacy of the courseware was conducted. OUTCOMES While a significant decline in the number of student queries was noted, an overwhelming majority of the survey respondents confirmed the usefulness of the purpose-developed courseware. CONCLUSIONS/RECOMMENDATIONS/SUMMARY The survey and lecturer’s experience indicated that animated demonstration video clips illustrating the various steps involved in developing hydrologic and hydraulic models and simulating design scenarios is an effective supplement for traditional learning resources. Among the many advantages of the custom-made video clips as a learning resource are that they (1) highlight the aspects that are important to undergraduate learning but not available in the software manuals as the latter are designed for more mature users/learners; (2) provide short, to-the point communication in a step-by-step manner; (3) allow students flexibility to self-learn at their own pace; (4) enhance student learning; and (5) enable time savings for the lecturer in the long term by avoiding queries of a repetitive nature. It is expected that these newly developed resources will be improved to incorporate students’ suggestions before being offered to future cohorts of students. The concept can also be expanded to other relevant courses where animated demonstrations of key modelling steps are beneficial to student learning.