CFD simulations of flow and heat transfer through the porous interface of a metal foam heat exchanger

This paper offers numerical modelling of a waste heat recovery system. A thin layer of metal foam is attached to a cold plate to absorb heat from hot gases leaving the system. The heat transferred from the exhaust gas is then transferred to a cold liquid flowing in a secondary loop. Two different foam PPI (Pores Per Inch) values are examined over a range of fluid velocities. Numerical results are then compared to both experimental data and theoretical results available in the literature. Challenges in getting the simulation results to match those of the experiments are addressed and discussed in detail. In particular, interface boundary conditions specified between a porous layer and a fluid layer are investigated. While physically one expects much lower fluid velocity in the pores compared to that of free flow, capturing this sharp gradient at the interface can add to the difficulties of numerical simulation. The existing models in the literature are modified by considering the pressure gradient inside and outside the foam. Comparisons against the numerical modelling are presented. Finally, based on experimentally-validated numerical results, thermo-hydraulic performance of foam heat exchangers as waste heat recovery units is discussed with the main goal of reducing the excess pressure drop and maximising the amount of heat that can be recovered from the hot gas stream.

A review on solar assisted heat pump systems in Singapore

A solar assisted heat pump is used for different applications, such as, water heating, drying and air conditioning. The unglazed evaporator-collector enables to absorb both solar energy and ambient energy due to low operating temperature. Three different systems are described: solar assisted heat pump system for hot water using an unglazed evaporator collector; solar assisted heat pump for hot water and drying, where evaporator collector and air collector are used; an integrated solar heat pump system making use of solar and ambient energy, and air-con waste heat. Unlike conventional collector, evaporator collector was found to have higher efficiency, 80% to 90%, and the coefficient of performance attained a value as high as 8.0. The integrated system leads to a reduction of global warming, as it uses solar energy, ambient energy and air-con waste heat.

Desalination of seawater using solar, ambient energy and waste heat from air conditioning

Desalination is considered one of the most suitable areas for the utilization of solar energy, as there are many places in the world where abundant supply of solar energy is available and also there is a great demand for fresh water. An integrated solar heat pump desalination system has been developed at the National University of Singapore. The system also offers the opportunity of water heating and drying utilizing solar, ambient energy and waste heat from air conditioning system, which is conventionally dumped into the environment causing global warming. Desalination is carried out by making use of a single effect of Multi-Effect Distillation (MED) system. Within the desalination chamber, both fl ashing and evaporation of saline water take place. The maximum Coefficient of Performance (COP) of the heat pump system was around 5.8. In the integrated system, the maximum fresh water production rate was 9.6 l h−1 and a Performance Ratio (PR) of 1.2. For only desalination, the system has the potential to produce a maximum of 30 l h−1 of fresh water.

Water heating and dehumidification with heat pump utilizing solar, ambient and waste heat

The low temperature operation of a heat pump makes it an excellent match for the use of solar energy. At the National University of Singapore, a solar assisted heat pump system has been designed, fabricated and installed to provide water heating and drying. The system also utilizes the air con waste heat, which would normally be released to atmosphere adding to global warming. Experimental results show that the twophase unglazed solar evaporator-collector, instead of losing energy to the ambient, gained a significant amount due to low operating temperature of the collector. As a result, the collector efficiency attains a value greater than 1, when conventional collector equations are used. With this evaporator-collector, the system can be operated even in the absence of solar irradiation. The waste heat was collected from an air-con system, which maintained a room at 20-22 oC. In the condenser side, water at 60 oC was produced at a rate of 3 liter/minute and the drying capacity was 2.2kg/hour. Maximum COP of the system was found to be about 5.5.

Hand, foot and mouth disease in China: Evaluating an automated system for the detection of outbreaks

Objective To evaluate the performance of China’s infectious disease automated alert and response system in the detection of outbreaks of hand, foot and mouth (HFM) disease. Methods We estimated size, duration and delay in reporting HFM disease outbreaks from cases notified between 1 May 2008 and 30 April 2010 and between 1 May 2010 and 30 April 2012, before and after automatic alert and response included HFM disease. Sensitivity, specificity and timeliness of detection of aberrations in the incidence of HFM disease outbreaks were estimated by comparing automated detections to observations of public health staff. Findings The alert and response system recorded 106 005 aberrations in the incidence of HFM disease between 1 May 2010 and 30 April 2012 – a mean of 5.6 aberrations per 100 days in each county that reported HFM disease. The response system had a sensitivity of 92.7% and a specificity of 95.0%. The mean delay between the reporting of the first case of an outbreak and detection of that outbreak by the response system was 2.1 days. Between the first and second study periods, the mean size of an HFM disease outbreak decreased from 19.4 to 15.8 cases and the mean interval between the onset and initial reporting of such an outbreak to the public health emergency reporting system decreased from 10.0 to 9.1 days. Conclusion The automated alert and response system shows good sensitivity in the detection of HFM disease outbreaks and appears to be relatively rapid. Continued use of this system should allow more effective prevention and limitation of such outbreaks in China.

A nationwide web-based automated system for early outbreak detection and rapid response in China

Timely reporting, effective analyses and rapid distribution of surveillance data can assist in detecting the aberration of disease occurrence and further facilitate a timely response. In China, a new nationwide web-based automated system for outbreak detection and rapid response was developed in 2008. The China Infectious Disease Automated-alert and Response System (CIDARS) was developed by the Chinese Center for Disease Control and Prevention based on the surveillance data from the existing electronic National Notifiable Infectious Diseases Reporting Information System (NIDRIS) started in 2004. NIDRIS greatly improved the timeliness and completeness of data reporting with real time reporting information via the Internet. CIDARS further facilitates the data analysis, aberration detection, signal dissemination, signal response and information communication needed by public health departments across the country. In CIDARS, three aberration detection methods are used to detect the unusual occurrence of 28 notifiable infectious diseases at the county level and to transmit that information either in real-time or on a daily basis. The Internet, computers and mobile phones are used to accomplish rapid signal generation and dissemination, timely reporting and reviewing of the signal response results. CIDARS has been used nationwide since 2008; all Centers for Disease Control and Prevention (CDC) in China at the county, prefecture, provincial and national levels are involved in the system. It assists with early outbreak detection at the local level and prompts reporting of unusual disease occurrences or potential outbreaks to CDCs throughout the country.

Project Diagnostics : Providing Successful Project Outcomes

Project Diagnostics is a tool for construction industry stakeholders wishing to improve project delivery and outcomes. This software identifies areas of poor project health, then establishes probable root causes and provides suggested remedial measures. Its focus is to act as an advanced warning system for construction projects that are failing to meet predetermined objectives based on the critical success factors (CSFs) of cost, time, quality, safety, relationships, environment and stakeholder value.

Socio-environmental factors and suicide in Queensland, Australia

Suicide has drawn much attention from both the scientific community and the public. Examining the impact of socio-environmental factors on suicide is essential in developing suicide prevention strategies and interventions, because it will provide health authorities with important information for their decision-making. However, previous studies did not examine the impact of socio-environmental factors on suicide using a spatial analysis approach. The purpose of this study was to identify the patterns of suicide and to examine how socio-environmental factors impact on suicide over time and space at the Local Governmental Area (LGA) level in Queensland. The suicide data between 1999 and 2003 were collected from the Australian Bureau of Statistics (ABS). Socio-environmental variables at the LGA level included climate (rainfall, maximum and minimum temperature), Socioeconomic Indexes for Areas (SEIFA) and demographic variables (proportion of Indigenous population, unemployment rate, proportion of population with low income and low education level). Climate data were obtained from Australian Bureau of Meteorology. SEIFA and demographic variables were acquired from ABS. A series of statistical and geographical information system (GIS) approaches were applied in the analysis. This study included two stages. The first stage used average annual data to view the spatial pattern of suicide and to examine the association between socio-environmental factors and suicide over space. The second stage examined the spatiotemporal pattern of suicide and assessed the socio-environmental determinants of suicide, using more detailed seasonal data. In this research, 2,445 suicide cases were included, with 1,957 males (80.0%) and 488 females (20.0%). In the first stage, we examined the spatial pattern and the determinants of suicide using 5-year aggregated data. Spearman correlations were used to assess associations between variables. Then a Poisson regression model was applied in the multivariable analysis, as the occurrence of suicide is a small probability event and this model fitted the data quite well. Suicide mortality varied across LGAs and was associated with a range of socio-environmental factors. The multivariable analysis showed that maximum temperature was significantly and positively associated with male suicide (relative risk [RR] = 1.03, 95% CI: 1.00 to 1.07). Higher proportion of Indigenous population was accompanied with more suicide in male population (male: RR = 1.02, 95% CI: 1.01 to 1.03). There was a positive association between unemployment rate and suicide in both genders (male: RR = 1.04, 95% CI: 1.02 to 1.06; female: RR = 1.07, 95% CI: 1.00 to 1.16). No significant association was observed for rainfall, minimum temperature, SEIFA, proportion of population with low individual income and low educational attainment. In the second stage of this study, we undertook a preliminary spatiotemporal analysis of suicide using seasonal data. Firstly, we assessed the interrelations between variables. Secondly, a generalised estimating equations (GEE) model was used to examine the socio-environmental impact on suicide over time and space, as this model is well suited to analyze repeated longitudinal data (e.g., seasonal suicide mortality in a certain LGA) and it fitted the data better than other models (e.g., Poisson model). The suicide pattern varied with season and LGA. The north of Queensland had the highest suicide mortality rate in all the seasons, while there was no suicide case occurred in the southwest. Northwest had consistently higher suicide mortality in spring, autumn and winter. In other areas, suicide mortality varied between seasons. This analysis showed that maximum temperature was positively associated with suicide among male population (RR = 1.24, 95% CI: 1.04 to 1.47) and total population (RR = 1.15, 95% CI: 1.00 to 1.32). Higher proportion of Indigenous population was accompanied with more suicide among total population (RR = 1.16, 95% CI: 1.13 to 1.19) and by gender (male: RR = 1.07, 95% CI: 1.01 to 1.13; female: RR = 1.23, 95% CI: 1.03 to 1.48). Unemployment rate was positively associated with total (RR = 1.40, 95% CI: 1.24 to 1.59) and female (RR=1.09, 95% CI: 1.01 to 1.18) suicide. There was also a positive association between proportion of population with low individual income and suicide in total (RR = 1.28, 95% CI: 1.10 to 1.48) and male (RR = 1.45, 95% CI: 1.23 to 1.72) population. Rainfall was only positively associated with suicide in total population (RR = 1.11, 95% CI: 1.04 to 1.19). There was no significant association for rainfall, minimum temperature, SEIFA, proportion of population with low educational attainment. The second stage is the extension of the first stage. Different spatial scales of dataset were used between the two stages (i.e., mean yearly data in the first stage, and seasonal data in the second stage), but the results are generally consistent with each other. Compared with other studies, this research explored the variety of the impact of a wide range of socio-environmental factors on suicide in different geographical units. Maximum temperature, proportion of Indigenous population, unemployment rate and proportion of population with low individual income were among the major determinants of suicide in Queensland. However, the influence from other factors (e.g. socio-culture background, alcohol and drug use) influencing suicide cannot be ignored. An in-depth understanding of these factors is vital in planning and implementing suicide prevention strategies. Five recommendations for future research are derived from this study: (1) It is vital to acquire detailed personal information on each suicide case and relevant information among the population in assessing the key socio-environmental determinants of suicide; (2) Bayesian model could be applied to compare mortality rates and their socio-environmental determinants across LGAs in future research; (3) In the LGAs with warm weather, high proportion of Indigenous population and/or unemployment rate, concerted efforts need to be made to control and prevent suicide and other mental health problems; (4) The current surveillance, forecasting and early warning system needs to be strengthened, to trace the climate and socioeconomic change over time and space and its impact on population health; (5) It is necessary to evaluate and improve the facilities of mental health care, psychological consultation, suicide prevention and control programs; especially in the areas with low socio-economic status, high unemployment rate, extreme weather events and natural disasters.

A multicast routing scheme for efficient safety message dissemination in VANET

Vehicular ad hoc network (VANET) is a wireless ad hoc network that operates in a vehicular environment to provide communication between vehicles. VANET can be used by a diverse range of applications to improve road safety. Cooperative collision warning system (CCWS) is one of the safety applications that can provide situational awareness and warning to drivers by exchanging safety messages between cooperative vehicles. Currently, the routing strategies for safety message dissemination in CCWS are scoped broadcast. However, the broadcast schemes are not efficient as a warning message is sent to a large number of vehicles in the area, rather than only the endangered vehicles. They also cannot prioritize the receivers based on their critical time to avoid collision. This paper presents a more efficient multicast routing scheme that can reduce unnecessary transmissions and also use adaptive transmission range. The multicast scheme involves methods to identify an abnormal vehicle, the vehicles that may be endangered by the abnormal vehicle, and the latest time for each endangered vehicle to receive the warning message in order to avoid the danger. We transform this multicast routing problem into a delay-constrained minimum Steiner tree problem. Therefore, we can use existing algorithms to solve the problem. The advantages of our multicast routing scheme are mainly its potential to support various road traffic scenarios, to optimize the wireless channel utilization, and to prioritize the receivers.

Medication warnings about driving : risk perceptions among French and Australian Communities

Increased crash risk is associated with sedative medications and researchers and health-professionals have called for improvements to medication warnings about driving. The tiered warning system in France since 2005 indicates risk level, uses a color-coded pictogram, and advises the user to seek the advice of a doctor before driving. In Queensland, Australia, the mandatory warning on medications that may cause drowsiness advises the user not to drive or operate machinery if they self-assess that they are affected, and calls attention to possible increased impairment when combined with alcohol. Objectives The reported aims of the study were to establish and compare risk perceptions associated with the Queensland and French warnings among medication users. It was conducted to complement the work of DRUID in reviewing the effectiveness of existing campaigns and practice guidelines. Methods Medication users in France and Queensland were surveyed using warnings about driving from both contexts to compare risk perceptions associated with each label. Both samples were assessed for perceptions of the warning that carried the strongest message of risk. The Queensland study also included perceptions of the likelihood of crash and level of impairment associated with the warning. Results Findings from the French study (N = 75) indicate that when all labels were compared, the majority of respondents perceived the French Level-3 label as the strongest warning about risk concerning driving. Respondents in Queensland had significantly stronger perceptions of potential impairment to driving ability, z = -13.26, p <.000 (n = 325), and potential chance of having a crash, z = -11.87, p < .000 (n = 322), after taking a medication that displayed the strongest French warning, compared with the strongest Queensland warning. Conclusions Evidence suggests that warnings about driving displayed on medications can influence risk perceptions associated with use of medication. Further analyses will determine whether risk perceptions influence compliance with the warnings.

Improved salinity management for the Nebine / Mungallala / Wallam catchment

The low stream salinity naturally in the Nebine-Mungallala Catchment, extent of vegetation retention, relatively low rainfall and high evaporation indicates that there is a relatively low risk of rising shallow groundwater tables in the catchment. Scalding caused by wind and water erosion exposing highly saline sub-soils is a more important regional issue, such as in the Homeboin area. Local salinisation associated with evaporation of bore water from free flowing bore drains and bores is also an important land degradation issue particularly in the lower Nebine, Wallam and Mungallala Creeks. The replacement of free flowing artesian bores and bore drains with capped bores and piped water systems under the Great Artesian Basin bore rehabilitation program is addressing local salinisation and scalding in the vicinity of bore drains and preventing the discharge of saline bore water to streams. Three principles for the prevention and control of salinity in the Nebine Mungallala catchment have been identified in this review: • Avoid salinity through avoiding scalds – i.e. not exposing the near-surface salt in landscape through land degradation; • Riparian zone management: Scalding often occurs within 200m or so of watering lines. Natural drainage lines are most likely to be overstocked, and thus have potential for scalding. Scalding begins when vegetation is removed, and without that binding cover, wind and water erosion exposes the subsoil; and • Monitoring of exposed or grazed soil areas. Based on the findings of the study, we make the following recommendations: 1. Undertake a geotechnical study of existing maps and other data to help identify and target areas most at risk of rising water tables causing salinity. Selected monitoring should then be established using piezometers as an early warning system. 2. SW NRM should financially support scald reclamation activity through its various funding programs. However, for this to have any validity in the overall management of salinity risk, it is critical that such funding require the landholder to undertake a salinity hazard/risk assessment of his/her holding. 3. A staged approach to funding may be appropriate. In the first instance, it would be reasonable to commence funding some pilot scald reclamation work with a view to further developing and piloting the farm hazard/risk assessment tools, and exploring how subsequent grazing management strategies could be incorporated within other extension and management activities. Once the details of the necessary farm level activities have been more clearly defined, and following the outcomes of the geotechnical review recommended above, a more comprehensive funding package could be rolled out to priority areas. 4. We recommend that best-practice grazing management training currently on offer should be enhanced with information about salinity risk in scald-prone areas, and ways of minimising the likelihood of scald formation. 5. We recommend that course material be developed for local students in Years 6 and 7, and that arrangements be made with local schools to present this information. Given the constraints of existing syllabi, we envisage that negotiations may have to be undertaken with the Department of Education in order for this material to be permitted to be used. We have contact with key people who could help in this if required. 6. We recommend that SW NRM continue to support existing extension activities such as Grazing Land Management and the Monitoring Made Easy tools. These aids should be able to be easily expanding to incorporate techniques for monitoring, addressing and preventing salinity and scalding. At the time of writing staff of SW NRM were actively involved in this process. It is important that these activities are adequately resourced to facilitate the uptake by landholders of the perception that salinity is an issue that needs to be addressed as part of everyday management. 7. We recommend that SW NRM consider investing in the development and deployment of a scenario-modelling learning support tool as part of the awareness raising and education activities. Secondary salinity is a dynamic process that results from ongoing human activity which mobilises and/or exposes salt occurring naturally in the landscape. Time scales can be short to very long, and the benefits of management actions can similarly have immediate or very long time frames. One way to help explain the dynamics of these processes is through scenario modelling.

Modeling perceived collision risk in port water navigation

An increase in the likelihood of navigational collisions in port waters has put focus on the collision avoidance process in port traffic safety. The most widely used on-board collision avoidance system is the automatic radar plotting aid which is a passive warning system that triggers an alert based on the pilot’s pre-defined indicators of distance and time proximities at the closest point of approaches in encounters with nearby vessels. To better help pilot in decision making in close quarter situations, collision risk should be considered as a continuous monotonic function of the proximities and risk perception should be considered probabilistically. This paper derives an ordered probit regression model to study perceived collision risks. To illustrate the procedure, the risks perceived by Singapore port pilots were obtained to calibrate the regression model. The results demonstrate that a framework based on the probabilistic risk assessment model can be used to give a better understanding of collision risk and to define a more appropriate level of evasive actions.

Hospital outpatient responses to potential driving impairment due to prescribed medications

Driving and using prescription medicines that have the potential to impair driving is an emerging research area. To date it is characterised by a limited (although growing) number of studies and methodological complexities that make generalisations about impairment due to medications difficult. Consistent evidence has been found for the impairing effects of hypnotics, sedative antidepressants and antihistamines, and narcotic analgesics, although it has been estimated that as many as nine medication classes have the potential to impair driving (Alvarez & del Rio, 2000; Walsh, de Gier, Christopherson, & Verstraete, 2004). There is also evidence for increased negative effects related to concomitant use of other medications and alcohol (Movig et al., 2004; Pringle, Ahern, Heller, Gold, & Brown, 2005). Statistics on the high levels of Australian prescription medication use suggest that consumer awareness of driving impairment due to medicines should be examined. One web-based study has found a low level of awareness, knowledge and risk perceptions among Australian drivers about the impairing effects of various medications on driving (Mallick, Johnston, Goren, & Kennedy, 2007). The lack of awareness and knowledge brings into question the effectiveness of the existing countermeasures. In Australia these consist of the use of ancillary warning labels administered under mandatory regulation and professional guidelines, advice to patients, and the use of Consumer Medicines Information (CMI) with medications that are known to cause impairment. The responsibility for the use of the warnings and related counsel to patients primarily lies with the pharmacist when dispensing relevant medication. A review by the Therapeutic Goods Administration (TGA) noted that in practice, advice to patients may not occur and that CMI is not always available (TGA, 2002). Researchers have also found that patients' recall of verbal counsel is very low (Houts, Bachrach, Witmer, Tringali, Bucher, & Localio, 1998). With healthcare observed as increasingly being provided in outpatient conditions (Davis et al., 2006; Vingilis & MacDonald, 2000), establishing the effectiveness of the warning labels as a countermeasure is especially important. There have been recent international developments in medication categorisation systems and associated medication warning labels. In 2005, France implemented a four-tier medication categorisation and warning system to improve patients' and health professionals' awareness and knowledge of related road safety issues (AFSSAPS, 2005). This warning system uses a pictogram and indicates the level of potential impairment in relation to driving performance through the use of colour and advice on the recommended behaviour to adopt towards driving. The comparable Australian system does not indicate the severity level of potential effects, and does not provide specific guidelines on the attitude or actions that the individual should adopt towards driving. It is reliant upon the patient to be vigilant in self-monitoring effects, to understand the potential ways in which they may be affected and how serious these effects may be, and to adopt the appropriate protective actions. This thesis investigates the responses of a sample of Australian hospital outpatients who receive appropriate labelling and counselling advice about potential driving impairment due to prescribed medicines. It aims to provide baseline data on the understanding and use of relevant medications by a Queensland public hospital outpatient sample recruited through the hospital pharmacy. It includes an exploration and comparison of the effect of the Australian and French medication warning systems on medication user knowledge, attitudes, beliefs and behaviour, and explores whether there are areas in which the Australian system may be improved by including any beneficial elements of the French system. A total of 358 outpatients were surveyed, and a follow-up telephone survey was conducted with a subgroup of consenting participants who were taking at least one medication that required an ancillary warning label about driving impairment. A complementary study of 75 French hospital outpatients was also conducted to further investigate the performance of the warnings. Not surprisingly, medication use among the Australian outpatient sample was high. The ancillary warning labels required to appear on medications that can impair driving were prevalent. A subgroup of participants was identified as being potentially at-risk of driving impaired, based on their reported recent use of medications requiring an ancillary warning label and level of driving activity. The sample reported previous behaviour and held future intentions that were consistent with warning label advice and health protective action. Participants did not express a particular need for being advised by a health professional regarding fitness to drive in relation to their medication. However, it was also apparent from the analysis that the participants would be significantly more likely to follow advice from a doctor than a pharmacist. High levels of knowledge in terms of general principles about effects of alcohol, illicit drugs and combinations of substances, and related health and crash risks were revealed. This may reflect a sample specific effect. Emphasis is placed in the professional guidelines for hospital pharmacists that make it essential that advisory labels are applied to medicines where applicable and that warning advice is given to all patients on medication which may affect driving (SHPA, 2006, p. 221). The research program applied selected theoretical constructs from Schwarzer's (1992) Health Action Process Approach, which has extended constructs from existing health theories such as the Theory of Planned Behavior (Ajzen, 1991) to better account for the intention-behaviour gap often observed when predicting behaviour. This was undertaken to explore the utility of the constructs in understanding and predicting compliance intentions and behaviour with the mandatory medication warning about driving impairment. This investigation revealed that the theoretical constructs related to intention and planning to avoid driving if an effect from the medication was noticed were useful. Not all the theoretical model constructs that had been demonstrated to be significant predictors in previous research on different health behaviours were significant in the present analyses. Positive outcome expectancies from avoiding driving were found to be important influences on forming the intention to avoid driving if an effect due to medication was noticed. In turn, intention was found to be a significant predictor of planning. Other selected theoretical constructs failed to predict compliance with the Australian warning label advice. It is possible that the limited predictive power of a number of constructs including risk perceptions is due to the small sample size obtained at follow up on which the evaluation is based. Alternately, it is possible that the theoretical constructs failed to sufficiently account for issues of particular relevance to the driving situation. The responses of the Australian hospital outpatient sample towards the Australian and French medication warning labels, which differed according to visual characteristics and warning message, were examined. In addition, a complementary study with a sample of French hospital outpatients was undertaken in order to allow general comparisons concerning the performance of the warnings. While a large amount of research exists concerning warning effectiveness, there is little research that has specifically investigated medication warnings relating to driving impairment. General established principles concerning factors that have been demonstrated to enhance warning noticeability and behavioural compliance have been extrapolated and investigated in the present study. The extent to which there is a need for education and improved health messages on this issue was a core issue of investigation in this thesis. Among the Australian sample, the size of the warning label and text, and red colour were the most visually important characteristics. The pictogram used in the French labels was also rated highly, and was salient for a large proportion of the sample. According to the study of French hospital outpatients, the pictogram was perceived to be the most important visual characteristic. Overall, the findings suggest that the Australian approach of using a combination of visual characteristics was important for the majority of the sample but that the use of a pictogram could enhance effects. A high rate of warning recall was found overall and a further important finding was that higher warning label recall was associated with increased number of medication classes taken. These results suggest that increased vigilance and care are associated with the number of medications taken and the associated repetition of the warning message. Significantly higher levels of risk perception were found for the French Level 3 (highest severity) label compared with the comparable mandatory Australian ancillary Label 1 warning. Participants' intentions related to the warning labels indicated that they would be more cautious while taking potentially impairing medication displaying the French Level 3 label compared with the Australian Label 1. These are potentially important findings for the Australian context regarding the current driving impairment warnings about displayed on medication. The findings raise other important implications for the Australian labelling context. An underlying factor may be the differences in the wording of the warning messages that appear on the Australian and French labels. The French label explicitly states "do not drive" while the Australian label states "if affected, do not drive", and the difference in responses may reflect that less severity is perceived where the situation involves the consumer's self-assessment of their impairment. The differences in the assignment of responsibility by the Australian (the consumer assesses and decides) and French (the doctor assesses and decides) approaches for the decision to drive while taking medication raises the core question of who is most able to assess driving impairment due to medication: the consumer, or the health professional? There are pros and cons related to knowledge, expertise and practicalities with either option. However, if the safety of the consumer is the primary aim, then the trend towards stronger risk perceptions and more consistent and cautious behavioural intentions in relation to the French label suggests that this approach may be more beneficial for consumer safety. The observations from the follow-up survey, although based on a small sample size and descriptive in nature, revealed that just over half of the sample recalled seeing a warning label about driving impairment on at least one of their medications. The majority of these respondents reported compliance with the warning advice. However, the results indicated variation in responses concerning alcohol intake and modifying the dose of medication or driving habits so that they could continue to drive, which suggests that the warning advice may not be having the desired impact. The findings of this research have implications for current countermeasures in this area. These have included enhancing the role that prescribing doctors have in providing warnings and advice to patients about the impact that their medication can have on driving, increasing consumer perceptions of the authority of pharmacists on this issue, and the reinforcement of the warning message. More broadly, it is suggested that there would be benefit in a wider dissemination of research-based information on increased crash risk and systematic monitoring and publicity about the representation of medications in crashes resulting in injuries and fatalities. Suggestions for future research concern the continued investigation of the effects of medications and interactions with existing medical conditions and other substances on driving skills, effects of variations in warning label design, individual behaviours and characteristics (particularly among those groups who are dependent upon prescription medication) and validation of consumer self-assessment of impairment.

Application of a digital elevation model for flood modeling for the Pagsangaan River in Leyte

Flood related scientific and community-based data are rarely systematically collected and analysed in the Philippines. Over the last decades the Pagsangaan River Basin, Leyte, has experienced several flood events. However, documentation describing flood characteristics such as extent, duration or height of these floods are close to non-existing. To address this issue, computerized flood modelling was used to reproduce past events where there was data available for at least partial calibration and validation. The model was also used to provide scenario-based predictions based on A1B climate change assumptions for the area. The most important input for flood modelling is a Digital Elevation Model (DEM) of the river basin. No accurate topographic maps or Light Detection And Ranging (LIDAR)-generated data are available for the Pagsangaan River. Therefore, the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Global Digital Elevation Map (GDEM), Version 1, was chosen as the DEM. Although the horizontal spatial resolution of 30 m is rather desirable, it contains substantial vertical errors. These were identified, different correction methods were tested and the resulting DEM was used for flood modelling. The above mentioned data were combined with cross-sections at various strategic locations of the river network, meteorological records, river water level, and current velocity to develop the 1D-2D flood model. SOBEK was used as modelling software to create different rainfall scenarios, including historic flooding events. Due to the lack of scientific data for the verification of the model quality, interviews with local stakeholders served as the gauge to judge the quality of the generated flood maps. According to interviewees, the model reflects reality more accurately than previously available flood maps. The resulting flood maps are now used by the operations centre of a local flood early warning system for warnings and evacuation alerts. Furthermore these maps can serve as a basis to identify flood hazard areas for spatial land use planning purposes.

A method for predicting rain-induced instability of an individual slope

Awareness to avoid losses and casualties due to rain-induced landslide is increasing in regions that routinely experience heavy rainfall. Improvements in early warning systems against rain-induced landslide such as prediction modelling using rainfall records, is urgently needed in vulnerable regions. The existing warning systems have been applied using stability chart development and real-time displacement measurement on slope surfaces. However, there are still some drawbacks such as: ignorance of rain-induced instability mechanism, mislead prediction due to the probabilistic prediction and short time for evacuation. In this research, a real-time predictive method was proposed to alleviate the drawbacks mentioned above. A case-study soil slope in Indonesia that failed in 2010 during rainfall was used to verify the proposed predictive method. Using the results from the field and laboratory characterizations, numerical analyses can be applied to develop a model of unsaturated residual soils slope with deep cracks and subject to rainwater infiltration. Real-time rainfall measurement in the slope and the prediction of future rainfall are needed. By coupling transient seepage and stability analysis, the variation of safety factor of the slope with time were provided as a basis to develop method for the real-time prediction of the rain-induced instability of slopes. This study shows the proposed prediction method has the potential to be used in an early warning system against landslide hazard, since the FOS value and the timing of the end-result of the prediction can be provided before the actual failure of the case study slope.