Assessing of circuit breaker restrike risks using computer simulation and wavelet analysis

A breaker restrike is an abnormal arcing phenomenon, leading to a possible breaker failure. Eventually, this failure leads to interruption of the transmission and distribution of the electricity supply system until the breaker is replaced. Before 2008, there was little evidence in the literature of monitoring techniques based on restrike measurement and interpretation produced during switching of capacitor banks and shunt reactor banks in power systems. In 2008 a non-intrusive radiometric restrike measurement method and a restrike hardware detection algorithm were developed by M.S. Ramli and B. Kasztenny. However, the limitations of the radiometric measurement method are a band limited frequency response as well as limitations in amplitude determination. Current restrike detection methods and algorithms require the use of wide bandwidth current transformers and high voltage dividers. A restrike switch model using Alternative Transient Program (ATP) and Wavelet Transforms which support diagnostics are proposed. Restrike phenomena become a new diagnostic process using measurements, ATP and Wavelet Transforms for online interrupter monitoring. This research project investigates the restrike switch model Parameter „A. dielectric voltage gradient related to a normal and slowed case of the contact opening velocity and the escalation voltages, which can be used as a diagnostic tool for a vacuum circuit-breaker (CB) at service voltages between 11 kV and 63 kV. During current interruption of an inductive load at current quenching or chopping, a transient voltage is developed across the contact gap. The dielectric strength of the gap should rise to a point to withstand this transient voltage. If it does not, the gap will flash over, resulting in a restrike. A straight line is fitted through the voltage points at flashover of the contact gap. This is the point at which the gap voltage has reached a value that exceeds the dielectric strength of the gap. This research shows that a change in opening contact velocity of the vacuum CB produces a corresponding change in the slope of the gap escalation voltage envelope. To investigate the diagnostic process, an ATP restrike switch model was modified with contact opening velocity computation for restrike waveform signature analyses along with experimental investigations. This also enhanced a mathematical CB model with the empirical dielectric model for SF6 (sulphur hexa-fluoride) CBs at service voltages above 63 kV and a generalised dielectric curve model for 12 kV CBs. A CB restrike can be predicted if there is a similar type of restrike waveform signatures for measured and simulated waveforms. The restrike switch model applications are used for: computer simulations as virtual experiments, including predicting breaker restrikes; estimating the interrupter remaining life of SF6 puffer CBs; checking system stresses; assessing point-on-wave (POW) operations; and for a restrike detection algorithm development using Wavelet Transforms. A simulated high frequency nozzle current magnitude was applied to an Equation (derived from the literature) which can calculate the life extension of the interrupter of a SF6 high voltage CB. The restrike waveform signatures for a medium and high voltage CB identify its possible failure mechanism such as delayed opening, degraded dielectric strength and improper contact travel. The simulated and measured restrike waveform signatures are analysed using Matlab software for automatic detection. Experimental investigation of a 12 kV vacuum CB diagnostic was carried out for the parameter determination and a passive antenna calibration was also successfully developed with applications for field implementation. The degradation features were also evaluated with a predictive interpretation technique from the experiments, and the subsequent simulation indicates that the drop in voltage related to the slow opening velocity mechanism measurement to give a degree of contact degradation. A predictive interpretation technique is a computer modeling for assessing switching device performance, which allows one to vary a single parameter at a time; this is often difficult to do experimentally because of the variable contact opening velocity. The significance of this thesis outcome is that it is a non-intrusive method developed using measurements, ATP and Wavelet Transforms to predict and interpret a breaker restrike risk. The measurements on high voltage circuit-breakers can identify degradation that can interrupt the distribution and transmission of an electricity supply system. It is hoped that the techniques for the monitoring of restrike phenomena developed by this research will form part of a diagnostic process that will be valuable for detecting breaker stresses relating to the interrupter lifetime. Suggestions for future research, including a field implementation proposal to validate the restrike switch model for ATP system studies and the hot dielectric strength curve model for SF6 CBs, are given in Appendix A.

Examining the effects of an eco-driving message on driver distraction

This paper examines the effects of an eco-driving message on driver distraction. Two in-vehicle distracter tasks were compared with an eco-driving task and a baseline task in an advanced driving simulator. N = 22 subjects were asked to perform an eco-driving, CD changing, and a navigation task while engaged in critical manoeuvres during which they were expected to respond to a peripheral detection task (PDT) with total duration of 3.5 h. The study involved two sessions over two consecutive days. The results show that drivers’ mental workloads are significantly higher during navigation and CD changing tasks in comparison to the two other scenarios. However, eco-driving mental workload is still marginally significant (p ∼ .05) across different manoeuvres. Similarly, event detection tasks show that drivers miss significantly more events in the navigation and CD changing scenarios in comparison to both the baseline and eco-driving scenario. Analysis of the practice effect shows that drivers’ baseline scenario and navigation scenario exhibit significantly less demand on the second day. Drivers also can detect significantly more events on the second day for all scenarios. The authors conclude that even reading a simple message while driving could potentially lead to missing an important event, especially when executing critical manoeuvres. However, there is some evidence of a practice effect which suggests that future research should focus on performance with habitual rather than novel tasks. It is recommended that sending text as an eco-driving message analogous to the study circumstances should not be delivered to drivers on-line when vehicle is in motion.

Coping with aggressive driving : driver accounts of how they manage themselves and others to reduce conflict on the road

Dealing with the aggression of other drivers on the road is an important skill given that driving is a common activity for adults in highly motorised countries. Even though incidents of extreme aggression on the road (such as assault) are reportedly rare, milder forms, some of them dangerous (such as tailgating or deliberately following too closely) are apparently common, and may be increasing. At the very least, this is likely to render the driving environment more stressful, and at worst elevates the risk of crashing by increasing both the level of risky driving behaviours and the likelihood of responses that escalate the situation. Thus the need for drivers to manage incidents of conflict is likely to become increasingly important. However, little research examines how drivers manage their own or others’ aggressive driving behaviour. Recently greater attention has been paid to driver cognitions, especially the attributions that drivers make about other drivers, that then might influence their own driving responses, particularly aggressive or risky ones. The study reported below was the first in a larger exploration of aggressive driving that focussed on driver cognitions, emotions and underlying motivations for aggressive behaviours on the road. Qualitative, in-depth interviews of drivers (n = 30, aged 18-49 years) were subjected to thematic analysis to investigate driver experiences with aggressive driving. Two main themes were identified from these accounts: driver management of self; and driver attempts to influence or manage other drivers. This paper describes the subthemes falling under the management of self main theme. These subthemes were labelled ‘being magnanimous’, ‘chilling out’, ‘slowing down’, and ‘apology/acknowledgment’. ‘Being magnanimous’ referred to situations where the respondent perceived him/herself to be a recipient of another’s aggressive driving and made a deliberate choice not to respond. However, a characteristic of this sub-theme was that this choice was underpinned by the adoption of morally superior stance, or sense of magnanimity. ‘Chilling out’ was a more general response to both the milder aggressive behaviours of other drivers and the general frustrations of driving. ‘Slowing down’ referred to reducing one’s speed in response to the perceived aggressive driving, often tailgating, of another. This subtheme appeared to consist of two separate underlying motivations. One of these was a genuine concern for one’s own safety while the other was more aimed at “getting back” at the other driver. ‘Apology’ referred to how drivers modified their more negative reactions and responses when another driver made gestures that acknowledged their having made a mistake, indicated an apology, or acknowledged the recipient driver. These sub-themes are discussed in relation to their implications for understanding aggressive driving and intervening to reduce it.

Connection without caution? The role of mobile phone involvement in predicting young people’s intentions to use a mobile phone while driving

The present study examined the predictors of the intentions of young people aged between 17 and 24 years (N = 196) to use their mobile phone while driving. Using convenience sampling, drivers were recruited at petrol station travel centres to complete a cross-sectional survey. The Theory of Planned Behaviour constructs of attitude, subjective norm, and perceived behavioural control (PBC) were measured, as well as mobile phone involvement - a construct based on behavioural addiction components to reflect people’s cognitive and behavioural interaction with their mobile phone. Attitudes, PBC, and mobile phone involvement predicted young people’s intentions to use their mobile phone while driving, highlighting the need for interventions to address the perceived rewards and costs of the behaviour and to challenge the potentially powerful need to be constantly connected with others by technology irrespective of the associated dangers.

Revised reinforcement sensitivity theory : the impact of FFFS and stress on driving

This study investigated the effect of a fear-based personality trait, as conceptualised in Gray’s revised reinforcement sensitivity theory (RST) by the strength of the fight/flight/freeze system (FFFS), on young people’s driving simulator performance under induced psychosocial stress. Seventy-one young drivers completed the Jackson-5 questionnaire of RST traits, followed by a psychosocial stress or relaxation induction procedure (random allocation to groups) and then a city driving simulator task. Some support was found for the hypothesis that higher FFFS sensitivity would result in poorer driving performance under stress, in terms of significantly poorer hazard responses, possibly due to an increased attentional focus on the aversive cues inherent in the stress induction leaving reduced attentional capacity for the driving task. These results suggest that stress may lead to riskier driving behaviour in individuals with fearful RST personality styles.

Evaluation of the GHR car following model for traffic safety studies

Traffic safety studies mandate more than what existing micro-simulation models can offer as they postulate that every driver exhibits a safe behaviour. All the microscopic traffic simulation models are consisting of a car-following model and the Gazis–Herman–Rothery (GHR) car-following model is a widely used model. This paper highlights the limitations of the GHR car-following model capability to model longitudinal driving behaviour for safety study purposes. This study reviews and compares different version of the GHR model. To empower the GHR model on precise metrics reproduction a new set of car-following model parameters is offered to simulate unsafe vehicle conflicts. NGSIM vehicle trajectory data is used to evaluate the new model and short following headways and Time to Collision are employed to assess critical safety events within traffic flow. Risky events are extracted from available NGSIM data to evaluate the modified model against the generic versions of the GHR model. The results from simulation tests illustrate that the proposed model does predict the safety metrics better than the generic GHR model. Additionally it can potentially facilitate assessing and predicting traffic facilities’ safety using microscopic simulation. The new model can predict Near-miss rear-end crashes.

Simulation-based comparison of pull-push system in motorcycle assembly line

To investigate the effects of adopting a pull system in assembly lines in contrast to a push system, simulation software called “ARENA” is used as a tool in order to present numerical results from both systems. Simulation scenarios are created to evaluate the effects of attributes changing in assembly systems, with influential factors including the change of manufacturing system (push system to pull system) and variation of demand. Moreover, pull system manufacturing consists of the addition attribute, which is the number of buffer storage. This paper will provide an analysis based on a previous case study, hence process time and workflow refer to the journal name “Optimising and simulating the assembly line balancing problem in a motorcycle manufacturing company: a case study” [2]. The implementation of the pull system mechanism is to produce a system improvement in terms of the number of Work-In-Process (WIP), total time of products in the system, and the number of finished product inventory, while retaining the same throughput.

An assessment tool for selection of appropriate daylighting solutions for buildings in tropical and subtropical regions : Validation using radiance simulation

A new decision-making tool that will assist designers in the selection of appropriate daylighting solutions for buildings in tropical locations has been previously proposed by the authors. Through an evaluation matrix that prioritizes the parameters that best respond to the needs of tropical climates (e.g. reducing solar gain and protection from glare) the tool determines the most appropriate devices for specific climate and building inputs. The tool is effective in demonstrating the broad benefits and limitations of the different daylight strategies for buildings in the tropics. However for thorough analysis and calibration of the tool, validation is necessary. This paper presents a first step in the validation process. RADIANCE simulations were conducted to compare simulation performance with the performance predicted by the tool. To this end, an office building case study in subtropical Brisbane, Australia, and five different daylighting devices including openings, light guiding systems and light transport systems were simulated. Illuminance, light uniformity, daylight penetration and glare analysis were assessed for each device. The results indicate the tool can appropriately rank and recommend daylighting strategies based on specific building inputs for tropical and subtropical regions, making it a useful resource for designers.

A micro-simulation of airport passengers with advanced traits

An approach for modeling passenger flows in airport terminals by a set of devised advanced traits of passengers is proposed. Advanced traits take into account a passenger’s cognitive preferences which would be the underlying motivations of route-choice decisions. Basic traits are the status of passengers such as travel class. Although the activities of passengers are normally regarded as stochastic and sometimes unpredictable, we advise that real scenarios of passenger flows are basically feasible to be compared with virtual simulations in terms of tactical route-choice decision-making by individual personals. Inside airport terminals, passengers are goal-directed and not only use standard processing check points but also behave discretionary activities during the course. In this paper, we integrated discretionary activities in the study to fulfill full-range of passenger flows. In the model passengers are built as intelligent agents who possess a bunch of initial basic traits and then can be categorized into ten distinguish groups in terms of route-choice preferences by inferring the results of advanced traits. An experiment is executed to demonstrate the capability to facilitate predicting passenger flows.

Do drivers respond emotionally and behaviourally differently to an intentionally anger provoking driving situation than to an ambiguous, but potentially provocative, one? Results of a self-report survey.

Aggressive driving is considered an important road-safety concern for drivers in highly motorised countries. However, understanding of the causes and maintenance factors fundamental to aggressive driving is limited. In keeping with theoretical advances from general aggression research such as the General Aggression Model (GAM), research has begun to examine the emotional and cognitive antecedents of aggressive driving in order to better understand the underlying processes motivating aggressive driving. Early findings in the driving area have suggested that greater levels of aggression are elicited in response to an intentionally aggressive on-road event. In contrast, general aggression research suggests that greater levels of aggression are elicited in response to an ambiguous event. The current study examined emotional and cognitive responses to two hypothetical driving scenarios with differing levels of aggressive intent (intentional versus ambiguous). There was also an interest in whether factors influencing responses were different for hostile aggression (that is, where the action is intended to harm the other) versus instrumental aggression (that is, where the action is motivated by an intention to remove an impediment or attain a goal). Results were that significantly stronger negative emotion and negative attributions, as well as greater levels of threat were reported in response to the scenario which was designed to appear intentional in nature. In addition, participants were more likely to endorse an aggressive behavioural response to a situation that appeared deliberately aggressive than to one where the intention was ambiguous. Analyses to determine if greater levels of negative emotions and cognitions are able to predict aggressive responses provided different patterns of results for instrumental aggression from those for hostile aggression. Specifically, for instrumental aggression, negative emotions and negative attributions were significant predictors for both the intentional and the ambiguous scenarios. In addition, perceived threat was also a significant predictor where the other driver’s intent was clearly aggressive. However, lower rather than higher, levels of perceived threat were associated with greater endorsement of an aggressive response. For hostile aggressive behavioural responses, trait aggression was the strongest predictor for both situations. Overall the results suggest that in the driving context, instrumental aggression is likely to be a much more common response than hostile aggression. Moreover, aggressive responses are more likely in situations where another driver’s behaviour is clearly intentional rather than ambiguous. The results also support the conclusion that there may be different underlying mechanisms motivating an instrumental aggressive response to those motivating a hostile one. In addition, understanding the emotions and cognitions underlying aggressive driving responses may be helpful in predicting and intervening to reduce driving aggression. The finding that drivers appear to regard tailgating as an instrumental response is of concern since this behaviour has the potential to result in crashes.

Communication and organizational social networks : a simulation model

Recent management research has evidenced the significance of organizational social networks, and communication is believed to impact the interpersonal relationships. However, we have little knowledge on how communication affects organizational social networks. This paper studies the dynamics between organizational communication patterns and the growth of organizational social networks. We propose an organizational social network growth model, and then collect empirical data to test model validity. The simulation results agree well with the empirical data. The results of simulation experiments enrich our knowledge on communication with the findings that organizational management practices that discourage employees from communicating within and across group boundaries have disparate and significant negative effect on the social network’s density, scalar assortativity and discrete assortativity, each of which correlates with the organization’s performance. These findings also suggest concrete measures for management to construct and develop the organizational social network.

Is simulation training effective in increasing podiatrists' confidence in foot ulcer management?

Background: Foot ulcers are a frequent reason for diabetes-related hospitalisation. Clinical training is known to have a beneficial impact on foot ulcer outcomes. Clinical training using simulation techniques has rarely been used in the management of diabetes-related foot complications or chronic wounds. Simulation can be defined as a device or environment that attempts to replicate the real world. The few non-web-based foot-related simulation courses have focused solely on training for a single skill or “part task” (for example, practicing ingrown toenail procedures on models). This pilot study aimed to primarily investigate the effect of a training program using multiple methods of simulation on participants’ clinical confidence in the management of foot ulcers. Methods: Sixteen podiatrists participated in a two-day Foot Ulcer Simulation Training (FUST) course. The course included pre-requisite web-based learning modules, practicing individual foot ulcer management part tasks (for example, debriding a model foot ulcer), and participating in replicated clinical consultation scenarios (for example, treating a standardised patient (actor) with a model foot ulcer). The primary outcome measure of the course was participants’ pre- and post completion of confidence surveys, using a five-point Likert scale (1 = Unacceptable-5 = Proficient). Participants’ knowledge, satisfaction and their perception of the relevance and fidelity (realism) of a range of course elements were also investigated. Parametric statistics were used to analyse the data. Pearson’s r was used for correlation, ANOVA for testing the differences between groups, and a paired-sample t-test to determine the significance between pre- and post-workshop scores. A minimum significance level of p < 0.05 was used. Results: An overall 42% improvement in clinical confidence was observed following completion of FUST (mean scores 3.10 compared to 4.40, p < 0.05). The lack of an overall significant change in knowledge scores reflected the participant populations’ high baseline knowledge and pre-requisite completion of web-based modules. Satisfaction, relevance and fidelity of all course elements were rated highly. Conclusions: This pilot study suggests simulation training programs can improve participants’ clinical confidence in the management of foot ulcers. The approach has the potential to enhance clinical training in diabetes-related foot complications and chronic wounds in general.

Comparison and modification of car following models toward a more accurate microscopic simulation parameters reproduction

Traffic safety studies demand more than what current micro-simulation models can provide as they presume that all drivers of motor vehicles exhibit safe behaviours. Several car-following models are used in various micro-simulation models. This research compares the mainstream car following models’ capabilities of emulating precise driver behaviour parameters such as headways and Time to Collisions. The comparison firstly illustrates which model is more robust in the metric reproduction. Secondly, the study conducted a series of sensitivity tests to further explore the behaviour of each model. Based on the outcome of these two steps exploration of the models, a modified structure and parameters adjustment for each car-following model is proposed to simulate more realistic vehicle movements, particularly headways and Time to Collision, below a certain critical threshold. NGSIM vehicle trajectory data is used to evaluate the modified models performance to assess critical safety events within traffic flow. The simulation tests outcomes indicate that the proposed modified models produce better frequency of critical Time to Collision than the generic models, while the improvement on the headway is not significant. The outcome of this paper facilitates traffic safety assessment using microscopic simulation.

Do people gamble with their lives : The relationship between risky driving behaviour and other risky behaviours

General risky behaviour is explored for correlation with risky driving behaviour in light of two theories, self-control and cross-situational consistency. Identification of general risky behaviours associated with risky driving behaviour, and the theory that best predicts the behaviours, will enable better targeting of intervention and education strategies to reduce driving related fatalities and injuries. A correlational study using participants (N=152) drawn from first year university undergraduates and the public surveyed their lifestyle and behaviours. Relationships were found between risky driving behaviours and other risky behaviours such as alcohol consumption, cannabis use and performing unlawful activities. No significant differences were found between genders, with the exception that males were more likely to believe that they were at risk of injury from their employment, χ2 (1, N = 152) = 4.49, p = .03, were more likely to have performed an unlawful offence, χ2 (1, N = 152) = 11.77, p = .001 and were more likely to drink drive, t (55.41) = -3.87, p < .001, mean difference = -0.63, CI 95% (-0.9, -0.37). People engaged in risky driving behaviours were more likely to engage in other risky behaviours. The theories that were explored were unable to accurately predict an association between general risky behaviour and driving without a license or when disqualified. Cross-situational consistency explained 20% (R2adj = .16) of the variance in which people engaged in risky driving with low self-control theory explaining an additional 0.3% variance (R2change = .003), F (8,143) = 6.92, p < .001. Driving while under the influence of alcohol could be predicted by risky behaviours in lifestyle, health, smoking, cannabis use and alcohol consumption, F (8,143) = 6.92, p < .001. The addition of self-control was not significant.