Tribological properties of γ-Y2Si2O7 ceramic against AISI 52100 steel and Si3N4 ceramic counterparts

Reciprocating ball-on-flat dry sliding friction and wear experiments have been conducted on singlephase γ-Y2Si2O7 ceramic flats in contact with AISI 52100 bearing steel and Si3N4 ceramic balls at 5-15N normal loads in an ambient environment. The kinetic friction coefficients of γ-Y2Si2O7 varied in the range over 0.53-0.63 against AISI 52100 steel and between 0.51-0.56 against Si3N4 ceramic. We found thatwear occurred predominantly during the running-in period and it almost ceased at the steady friction stage. The wear rates of γ-Y2Si2O7 were in the order of 10-4mm3/(N m). Besides, wear debris strongly influenced the friction and wear processes. The strong chemical affinity between γ-Y2Si2O7 and AISI 52100 balls led to a thick transfer layer formed on both contact surfaces of the flat and counterpart ball, which changed the direct sliding between the ball and the flat into a shearing within the transfer layer. For the γ-Y2Si2O7/Si3N4 pair, a thin silica hydrate lubricant tribofilm presented above the compressed debris entrapped in the worn track and contact ball surface. This transfer layer and the tribofilm separated the sliding couple from direct contact and contributed to the low friction coefficient and wear rate.

A journey access tool to facilitate mobility-related access for people with disabilities in low and middle income countries

People with disabilities (PWD) experience difficulties in accessing the transport system (including both infrastructure and services) to meet their needs for health care, employment and other activities. Our research shows that lack of access to the journeys needed for these purposes is a more significant barrier in low and middle income countries than in high income countries, and results in inadequate health care, rehabilitation and access to education and employment. At the same time, the existing transport system in low and middle income countries presents much higher road crash risks than in high income countries. By combining the principles and methods of Road Safety Audit and disability access, and adapting these Western approaches to a low/middle income country context, we have worked with Handicap International Cambodia to develop a Journey Access Tool (JAT) for use by disabled peoples’ organisations (DPOs), people with a disability and other key stakeholders. A key element of the approach is that it involves the participation of PWD on the journeys that they need to take, and it identifies infrastructure and service improvements that should be prioritised in order to facilitate access to these journeys. The JAT has been piloted in Cambodia with a range of PWD. This presentation will outline the design of the JAT and the results of the pilot studies. The information gained thus far strongly suggests that the JAT is a valuable and cost-effective approach that can be used by DPOs and professionals to identify barriers to access and prioritise the steps needed to address them.

Western medicine and Australian Indigenous healing practices

Most projects undertaken by government health organisations are formulated on values and beliefs about health and illness that are derived from Anglo/Celtic culture. Health beliefs differ between cultures and it has been identified that the differences in the Indigenous and non-Indigenous constructs of health impacts negatively on the effectiveness of mainstream healthcare provided to Indigenous peoples [2]. This implies that strategies that incorporate, or better still are derived from, Indigenous health beliefs have a greater potential to be effective. This article introduces a prospective survey project asking how western medicine and traditional treatments interface with each other.

An investigation into the thermophysical and rheological properties of nanofluids for solar thermal applications

Considered to be the next generation of heat transfer fluids, nanofluids have been receiving a growing amount of attention in the past decade despite the controversy and inconsistencies that have been reported. Nanofluids have great potential in a wide range of fields, particularly for solar thermal applications. This paper presents a comprehensive review of the literature on the enhancements in thermophysical and rheological properties resulting from experimental works conducted on molten salt nanofluids that are used in solar thermal energy systems. It was found that an increase in specific heat of 10–30% was achieved for most nanofluids and appeared independent of particle size and to an extent mass concentration. The specific heat increase was attributed to the formation of nanostructures at the solid–liquid interface and it was also noted that the aggregation of nanoparticles has detrimental effects on the specific heat increase. Thermal conductivity was also found to increase, though less consistently, ranging from 3% to 35%. Viscosity was seen to increase with the addition of nanoparticles and is dependent on the amount of aggregation of the particles. An in-depth micro level analysis of the mechanisms behind the thermophysical property changes is presented in this paper. In addition, possible trends are discussed relating to current theorised mechanisms in an attempt to explain the behaviour of molten salt nanofluids.

Characterisation of head-hardened rail steel in terms of cyclic plasticity response and microstructure for improved material modelling

Stress- and strain-controlled tests of heat treated high-strength rail steel (Australian Standard AS1085.1) have been performed in order to improve the characterisation of the said material׳s ratcheting and fatigue wear behaviour. The hardness of the rail head material has also been studied and it has been found that hardness reduces considerably below four-millimetres from the rail top surface. Historically, researchers have used test coupons with circular cross-sections to conduct cyclic load tests. Such test coupons, typically five-millimetres in gauge diameter and ten‐millimetres in grip diameter, are usually taken from the rail head sample. When there is considerable variation of material properties over the cross-section it becomes likely that localised properties of the rail material will be missed. In another case from the literature, disks 47 mm in diameter for a twin-disk rolling contact test machine were obtained directly from the rail sample and used to validate ratcheting and rolling contact fatigue wear models. The question arises: How accurate are such tests, especially when large material property gradients exist? In this research paper, the effects of rail sampling location on the ratcheting behaviour of AS1085.1 rail steel were investigated using rectangular-shaped specimens obtained at four different depths to observe their respective cyclic plasticity behaviour. The microstructural features of the test coupons were also analysed, especially the pearlite inter-lamellar spacing which showed strong correlation with both hardness and cyclic plasticity behaviour of the material. This work ultimately provides new data and testing methodology to aid the selection of valid parameters for material constitutive models to better understand rail surface ratcheting and wear.