Fracture analysis of wind turbine main shaft

Shaft fracture at an early stage of operation is a common problem for a certain type of wind turbine. To determine the cause of shaft failure a series of experimental tests were conducted to evaluate the chemical composition and mechanical properties. A detail analysis involving macroscopic feature and microstructure analysis of the material of the shaft was also performed to have an in depth knowledge of the cause of fracture. The experimental tests and analysis results show that there are no significant differences in the material property of the main shaft when comparing it with the Standard, EN10083-3:2006. The results show that stress concentration on the shaft surface close to the critical section of the shaft due to rubbing of the annular ring and coupled with high stress concentration caused by the change of inner diameter of the main shaft are the main reasons that result in fracture of the main shaft. In addition, inhomogeneity of the main shaft micro-structure also accelerates up the fracture process of the main shaft. In addition, the theoretical calculation of equivalent stress at the end of the shaft was performed, which demonstrate that cracks can easily occur under the action of impact loads. The contribution of this paper is to provide a reference in fracture analysis of similar main shaft of wind turbines.

Sintering and densification mechanisms of Y2BaCuO5 pellets

The sintering and densification of Y2BaCuO5 (Y-211) pellets made from powders with different characteristics have been investigated in the temperature range 1000-1140°C. A pellet made from powder containing Ba-rich secondary phases shows very early liquid-assisted sintering and densification and clear evidence of exaggerated grain growth. The melting of BaCuO2 and YBa2Cu3O7-δ (Y-123) secondary phases increases the rate of densification of Y-211 pellets made from other powders at temperatures above 1025-1030°C. All the liquid produced by the melting of the latter phases recrystallizes as intergranular layers of Y-123. These intergranular layers account for the darker appearance and for measurable electrical conductivities at room temperature of the pellets sintered at the higher temperatures. The development of exaggerated grain growth within a uniform fine-grained matrix opens the possibility of using controlled secondary recrystallization to obtain large single domains of Y-211, provided that the trapping of porosity can be avoided or minimized. © 1999 Elsevier Science S.A.

Local plastic mechanisms in thin steel plates under in-plane compression

Thin-walled steel plates subjected to in-plane compression develop two types of local plastic mechanism, namely the roof-shaped mechanism and the so-called flip-disc mechanism, but the intriguing question of why two mechanisms should develop was not answered until recently. It was considered that the location of first yield point shifted from the centre of the plate to the midpoint of the longitudinal edge depending on the b/t ratio, imperfection level, and yield stress of steel, which then decided the type of mechanism. This paper has verified this hypothesis using analysis and laboratory experiments. An elastic analysis using Galerkin's method to solve Marguerre's equations was first used to determine the first yield point, based on which the local plastic mechanism/imperfection tolerance tables have been developed which give the type of mechanism as a function of b/t ratio, imperfection level and yield stress of steel. Laboratory experiments of thin-walled columns verified the imperfection tolerance tables and thus indirectly the hypothesis. Elastic and rigid-plastic curves were them used to predict the effect on the ultimate load due to the change of mechanism. A finite element analysis of selected cases also confirmed the results from simple analyses and experiments.

Comparative study of failure mechanisms in steel and concrete members strengthened with CFRP composites

Over the last decade advanced composite materials, like carbon fibre reinforced polymer (CFRP), have increasingly been used in civil engineering infrastructure. The benefits of advanced composites are rapidly becoming evident. This paper focuses on the comparative performance of steel and concrete members retrofitted by carbon fibre reinforced polymers. The objective of this work is a systematic assessment and evaluation of the performance of CFRP for both the concrete and steel members available in the technical literature. Existing empirical and analytical models were studied. Comparison is made with respect to failure mode, bond characteristics, fatigue behaviour, durability, corrosion, load carrying capacity and force transfer. It is concluded that empirical expressions for the concrete-CFRP composite are not readily suited for direct use in the steel-CFRP composite. This paper identifies some of the major issues that need further investigation.

INFORMAS (International Network for Food and Obesity/non-communicable diseases Research, Monitoring and Action Support) : overview and key principles

Non-communicable diseases (NCDs) dominate disease burdens globally and poor nutrition increasingly contributes to this global burden. Comprehensive monitoring of food environments, and evaluation of the impact of public and private sector policies on food environments is needed to strengthen accountability systems to reduce NCDs. The International Network for Food and Obesity/NCDs Research, Monitoring and Action Support (INFORMAS) is a global network of public-interest organizations and researchers that aims to monitor, benchmark and support public and private sector actions to create healthy food environments and reduce obesity, NCDs and their related inequalities. The INFORMAS framework includes two ‘process’ modules, that monitor the policies and actions of the public and private sectors, seven ‘impact’ modules that monitor the key characteristics of food environments and three ‘outcome’ modules that monitor dietary quality, risk factors and NCD morbidity and mortality. Monitoring frameworks and indicators have been developed for 10 modules to provide consistency, but allowing for stepwise approaches (‘minimal’, ‘expanded’, ‘optimal’) to data collection and analysis. INFORMAS data will enable benchmarking of food environments between countries, and monitoring of progress over time within countries. Through monitoring and benchmarking, INFORMAS will strengthen the accountability systems needed to help reduce the burden of obesity, NCDs and their related inequalities.

Multiple types of data are required to identify the mechanisms influencing the spatial expansion of melanoma cell colonies

Background The expansion of cell colonies is driven by a delicate balance of several mechanisms including cell motility, cell-to-cell adhesion and cell proliferation. New approaches that can be used to independently identify and quantify the role of each mechanism will help us understand how each mechanism contributes to the expansion process. Standard mathematical modelling approaches to describe such cell colony expansion typically neglect cell-to-cell adhesion, despite the fact that cell-to-cell adhesion is thought to play an important role. Results We use a combined experimental and mathematical modelling approach to determine the cell diffusivity, D, cell-to-cell adhesion strength, q, and cell proliferation rate, ?, in an expanding colony of MM127 melanoma cells. Using a circular barrier assay, we extract several types of experimental data and use a mathematical model to independently estimate D, q and ?. In our first set of experiments, we suppress cell proliferation and analyse three different types of data to estimate D and q. We find that standard types of data, such as the area enclosed by the leading edge of the expanding colony and more detailed cell density profiles throughout the expanding colony, does not provide sufficient information to uniquely identify D and q. We find that additional data relating to the degree of cell-to-cell clustering is required to provide independent estimates of q, and in turn D. In our second set of experiments, where proliferation is not suppressed, we use data describing temporal changes in cell density to determine the cell proliferation rate. In summary, we find that our experiments are best described using the range D = 161 - 243 ?m2 hour-1, q = 0.3 - 0.5 (low to moderate strength) and ? = 0.0305 - 0.0398 hour-1, and with these parameters we can accurately predict the temporal variations in the spatial extent and cell density profile throughout the expanding melanoma cell colony. Conclusions Our systematic approach to identify the cell diffusivity, cell-to-cell adhesion strength and cell proliferation rate highlights the importance of integrating multiple types of data to accurately quantify the factors influencing the spatial expansion of melanoma cell colonies.

A theory of process modelling impact

Process modelling – the design and use of graphical documentations of an organisation’s business processes – is a key method to document and use information about business processes. Still, despite current interest in process modelling, this research area faces essential challenges. Key unanswered questions concern the impact of process modelling in organisational practice, and the mechanisms through which impacts are developed. To answer these questions and to provide a better understanding of process modelling impact, I turn to the concept of affordances. Affordances describe the possibilities for goal-oriented action that technical objects offer to specified users. This notion has received growing attention from IS researchers. I report on my efforts to further develop the IS discipline’s understanding of affordances and impacts from informational objects, such as process models used by analysts for purposes of information systems analysis and design. Specifically, I seek to extend existing theory on the emergence and actualisation of affordances. I develop a research model that describes the process by which affordances are perceived and actualised and explain their dependence on available information and actualisation effort. I present my plans for operationalising and testing this research model empirically, and provide details about my design of a full-cycle, mixed methods study currently in progress.

Action and Adventure

This chapter discusses the history of action and adventure films in Australian cinema. It focuses on those films starring Australian actors who have gained international fame, and on those films featuring a female protagonist.

The innovation potential of living-labs to strengthen small and medium enterprises in regional Australia

The small and medium enterprise (SME) sector has been the major source of well-being and employment opportunities in regional Australia. Consequently, fostering the innovative capacity of SMEs in regions that are struggling to grow their economies and distribute the growth fairly while not degrading the environment has never been more important. While SMEs generally face more uncertainties in relation to resources (e.g. financial, human and social capital) when compared to larger businesses, collaborative, cuttingedge mechanisms to enhance innovation capabilities of regional SMEs are lacking. This paper responds to this gap and proposes a Living Laboratory – an open, multi-disciplinary and multi-stakeholder action research platform where innovations can be co-created, tested and evaluated in the every-day environment of SMEs – as a way to strengthen the SME sector in regional Australia.

C. elegans RNA-dependent RNA polymerases rrf-1 and ego-1 silence Drosophila transgenes by differing mechanisms

Drosophila possesses the core gene silencing machinery but, like all insects, lacks the canonical RNA-dependent RNA polymerases (RdRps) that in C. elegans either trigger or enhance two major small RNA-dependent gene silencing pathways. Introduction of two different nematode RdRps into Drosophila showed them to be functional, resulting in differing silencing activities. While RRF-1 enhanced transitive dsRNA-dependent silencing, EGO-1 triggered dsRNA-independent silencing, specifically of transgenes. The strain w; da-Gal4; UAST-ego-1, constitutively expressing ego-1, is capable of silencing transgene including dsRNA hairpin upon a single cross, which created a powerful tool for research in Drosophila. In C. elegans, EGO-1 is involved in transcriptional gene silencing (TGS) of chromosome regions that are unpaired during meiosis. There was no opportunity for meiotic interactions involving EGO-1 in Drosophila that would explain the observed transgene silencing. Transgene DNA is, however, unpaired during the pairing of chromosomes in embryonic mitosis that is an unusual characteristic of Diptera, suggesting that in Drosophila, EGO-1 triggers transcriptional silencing of unpaired DNA during embryonic mitosis. © 2012 Springer Basel.

Footprints to pathways : reconciliation action planning in industry to sustain Indigenous employment in Queensland

This paper provides an introductory discussion to a study focusing on industry Reconciliation Action Plans (RAP) and sustaining Indigenous employment in Queensland. Indigenous people continue to experience deep and persistent disadvantage in employment, which limits their life prospects (McLachlan, Gilgillan & Gordon, 2013). A major contributing factor to this detriment is irregular employment and or unemployment. A reasonable standard of living has been found to be determined by access to economic resources such as income and wealth. Denial of this access, denies access to income streams, social status, and engagement in meaningful activities. Hence, job loss and joblessness are triggers of disadvantage (McLachlan, et al., 2013). For young Indigenous people, lack of access has lasting effects particularly if they have multiple characteristics that place them at risk of disadvantage. The project aims to develop knowledge and understanding of Industry RAPs mediate employment opportunities for Indigenous people and how young Indigenous people conceive of their employment options and the processes by which employers can best support Indigenous people. It adopts two theoretical frameworks to investigate the aim of the study : (1) Lave and Wenger’s (1991) theory of communities of practice and, (2) Sen’s (1993) capability approach which provides a structure for examining individual well-being in the context of societal inequality. This paper discusses the first research question of the study: What are Industry Reconciliation Action Plans? What is included in RAPs? Why do Industries develop RAPs? How do RAPs attract, recruit, retain, and tenure Indigenous people? The project’s significance rests with its focus on Industry, employers, policies and practices that aid the attraction and retention of Indigenous people in employment.

Designing REDD+ to be just : considerations for a legally binding instrument

The international climate regime is in the process of negotiating a legally binding instrument concerning Reducing Emissions from Deforestation and Degradation (REDD+). The paper starts by exploring the complex web of decisions and advices that currently regulate REDD+ initiatives within the international climate regime. This is followed by an analysis of justice issues raised by non-state actors in the REDD+ international negotiations. The paper concludes by building on this analysis to identify some relevant considerations when seeking to design a just and legally binding REDD+ instrument. These considerations include: the impact of market- versus fund-based investment channels, the importance of defining a clear objective; the inclusion and role of international principles such as sovereignty, preventative action, common but differentiated responsibility, sustainable development, and Free, Prior, and Informed Consent; the appropriate design of REDD+ safeguards and the inclusion of grievance mechanisms within the instrument which provide guidance on resolving disputes associated with REDD+ investment.

The potential role of lycopene for the prevention and therapy of prostate cancer : from molecular mechanisms to clinical evidence

Lycopene is a phytochemical that belongs to a group of pigments known as carotenoids. It is red, lipophilic and naturally occurring in many fruits and vegetables, with tomatoes and tomato-based products containing the highest concentrations of bioavailable lycopene. Several epidemiological studies have linked increased lycopene consumption with decreased prostate cancer risk. These findings are supported by in vitro and in vivo experiments showing that lycopene not only enhances the antioxidant response of prostate cells, but that it is even able to inhibit proliferation, induce apoptosis and decrease the metastatic capacity of prostate cancer cells. However, there is still no clearly proven clinical evidence supporting the use of lycopene in the prevention or treatment of prostate cancer, due to the only limited number of published randomized clinical trials and the varying quality of existing studies. The scope of this article is to discuss the potential impact of lycopene on prostate cancer by giving an overview about its molecular mechanisms and clinical effects. © 2013 by the authors; licensee MDPI, Basel, Switzerland.

Eph receptors and their ligands : promising molecular biomarkers and therapeutic targets in prostate cancer

Although at present, there is a high incidence of prostate cancer, particularly in the Western world, mortality from this disease is declining and occurs primarily only from clinically significant late stage tumors with a poor prognosis. A major current focus of this field is the identification of new biomarkers which can detect earlier, and more effectively, clinically significant tumors from those deemed “low risk”, as well as predict the prognostic course of a particular cancer. This strategy can in turn offer novel avenues for targeted therapies. The large family of Receptor Tyrosine Kinases, the Ephs, and their binding partners, the ephrins, has been implicated in many cancers of epithelial origin through stimulation of oncogenic transformation, tumor angiogenesis, and promotion of increased cell survival, invasion and migration. They also show promise as both biomarkers of diagnostic and prognostic value and as targeted therapies in cancer. This review will briefly discuss the complex roles and biological mechanisms of action of these receptors and ligands and, with regard to prostate cancer, highlight their potential as biomarkers for both diagnosis and prognosis, their application as imaging agents, and current approaches to assessing them as therapeutic targets. This review demonstrates the need for future studies into those particular family members that will prove helpful in understanding the biology and potential as targets for treatment of prostate cancer.

Road safety knowledge exchange and capacity building between China and Australia

Road traffic injuries are one of the major public health burdens worldwide. The United Nations Decade of Action for Road Safety (2011-2020) implores all nations to work to reduce this burden. This decade represents a unique and historic period of time in the field of road safety. Information exchange and co-operation between nations is an important step in achieving the goal. The burden of road crashes, fatalities and injuries is not equally distributed. We know that low and middle-income countries experience the majority of the road trauma burden. Therefore it is imperative that these countries learn from the successes of others that have developed and implemented road safety laws, public education campaigns and countermeasures over many years and have achieved significant road trauma reductions as a result. China is one of the countries experiencing a large road trauma burden. Vulnerable road users such as pedestrians and cyclists make up a large proportion of fatalities and injuries in China. Speeding, impaired/drug driving, distracted driving, vehicle overloading, inadequate road infrastructure, limited use of safety restraints and helmets, and limited road safety training have all been identified as contributing to the problem. Some important steps have been taken to strengthen China’s approach, including increased penalties for drunk driving in May 2011 and increased attention to school bus safety in 2011/12. However, there is still a large amount of work needed to improve the current road safety position in China. This paper provides details of a program to assist with road safety knowledge exchange between China and Australia that was funded by the Australian Government which was undertaken in the latter part of 2012. The four month program provided the opportunity for the first author to work closely with key agencies in Australia that are responsible for policy development and implementation of a broad range of road safety initiatives. In doing so, an in-depth understanding was gained about key road safety strategies in Australia and processes for developing and implementing them. Insights were also gained into the mechanisms used for road safety policy development, implementation and evaluation in several Australian jurisdictions. Road traffic law and enforcement issues were explored with the relevant jurisdictional transport and police agencies to provide a greater understanding of how Chinese laws and practices could be enhanced. Working with agencies responsible for public education and awareness campaigns about road safety in Australia also provided relevant information about how to promote road safety at the broader community level in China. Finally, the program provided opportunities to work closely with several world-renowned Australian research centres and key expert researchers to enhance opportunities for ongoing road safety research in China. The overall program provided the opportunity for the first author to develop knowledge in key areas of road safety strategy development, implementation and management which are directly relevant to the current situation in China. This paper describes some main observations and findings from participation in the program.