The influence of temperature and introduction point on the detection of Rhyzopertha dominica in stored grain

The presence of insect pests in grain storages throughout the supply chain is a significant problem for farmers, grain handlers, and distributors world-wide. Insect monitoring and sampling programmes are used in the stored grains industry for the detection and estimation of pest populations. At the low pest densities dictated by economic and commercial requirements, the accuracy of both detection and abundance estimates can be influenced by variations in the spatial structure of pest populations over short distances. Geostatistical analysis of Rhyzopertha dominica populations in 2 and 3 dimensions showed that insect numbers were positively correlated over short (0.5 cm) distances, and negatively correlated over longer (.10 cm) distances. At 35 C, insects were located significantly further from the grain surface than at 25 and 30 C. Dispersion metrics showed statistically significant aggregation in all cases. The observed heterogeneous spatial distribution of R. dominica may also be influenced by factors such as the site of initial infestation and disturbance during handling. To account for these additional factors, I significantly extended a simulation model that incorporates both pest growth and movement through a typical stored-grain supply chain. By incorporating the effects of abundance, initial infestation site, grain handling, and treatment on pest spatial distribution, I developed a supply chain model incorporating estimates of pest spatial distribution. This was used to examine several scenarios representative of grain movement through a supply chain, and determine the influence of infestation location and grain disturbance on the sampling intensity required to detect pest infestations at various infestation rates. This study has investigated the effects of temperature, infestation point, and grain handling on the spatial distribution and detection of R. dominica. The proportion of grain infested was found to be dependent upon abundance, initial pest location, and grain handling. Simulation modelling indicated that accounting for these factors when developing sampling strategies for stored grain has the potential to significantly reduce sampling costs while simultaneously improving detection rate, resulting in reduced storage and pest management cost while improving grain quality.

The role for police in addressing alcohol-related harm inside and outside licensed premises

Alcohol consumption is enmeshed with Australian culture (Palk, 2008) and the use and misuse of alcohol contributes to considerable health and social harms (Barbor et al., 2010; English et al., 1995; Gutjahr, Gmel, & Rehm, 2001; Palk, 2008; Steenkamp, Harrison, & Allsop, 2002). Despite shifts in the way that alcohol is consumed and how it is used, it has been reported that one-third of all alcohol consumed is done so within licensed premises (Lang, Stockwell, Rydon, & Gamble, 1992). Consequently, licensed premises are over-represented as settings in which alcohol-related harms occur. These harms, particularly those related to violence, are associated with particular licensed premises operating in the night-time economy (Briscoe & Donnelly, 2001b; Chikritzhs, Stockwell, & Masters, 1997; Homel, Tomsen, & Thommeny, 1991; Stockwell, 1997). Police have a role in not only responding to the manifestation of harms, such as crime, injuries, assaults, domestic violence, stealing and sexual offences, but they also have a role in preventing problems, and thereby reducing alcohol and other drug-related harms (Doherty & Roche, 2003). Given the extent of alcohol consumption within licensed premises and the nature and extent of the harms, as well as the lack of opportunity to influence outcomes in other settings (e.g. the home), licensed premises offer police and other stakeholders a significant opportunity to influence positively the reduction of alcoholrelated harm. This research focuses specifically on the police role in policing licensed premises. Primarily, this research aims to investigate the factors which are relevant to why and how police officers respond to alcohol-related incidents inside and outside licensed premises. It examines the attitudes and beliefs of police and assesses their knowledge, capacity and ability to effectively police licensed premises. The research methodology uses three distinct surveys. Each contributes to understanding the motivations and practice of police officers in this important area of harm reduction. Study One involved a survey of police officers within a police district (Brisbane Central District) in Queensland, Australia and used a comprehensive questionnaire involving both quantitative and qualitative techniques. A key research outcome of Study One was the finding that officers had low levels of knowledge of the strategies that are effective in addressing alcohol-related harm both inside and outside licensed premises. Paradoxically, these officers also reported extensive recent experience in dealing with alcohol issues in these locations. In addition, these officers reported that alcohol was a significant contextual factor in the majority of matters to which they responded. Officers surveyed reported that alcohol increased the difficulty of responding to situations and that licensed premises (e.g. nightclubs, licensed clubs and hotels) were the most difficult contexts to police. Those surveyed were asked to self-assess their knowledge of the Liquor Act (Qld), which is the primary legislative authority in Queensland for regulating licensed premises. Surprisingly, well over half of the officers (65%) reported ‘no’ to ‘fair’ knowledge of the Act, despite officers believing that their skill level to police such premises was in the ‘good to very good range’. In an important finding, officers reported greater skill level to police outside licensed premises than inside such premises, indicating that officers felt less capable, from a skill perspective, to operate within the confines of a licensed premise than in the environment immediately outside such premises. Another key finding was that officers reported greater levels of training in responding to situations outside and around licensed premises than to situations inside licensed premises. Officers were also asked to identify the frequency with which they employed specified regulatory enforcement and community-based strategies. Irrespective of the type of response, ‘taking no action’ or passive policing interventions were not favoured by officers. The findings identified that officers favoured taking a range of strategies (sending home, releasing into the custody of friends, etc.) in preference to arrest. In another key finding, officers generally reported their support for operational stakeholder partnership approaches to policing licensed premises. This was evidenced by the high number of officers (over 90%) reporting that there should be shared responsibility for enforcing the provisions of the Liquor Act. Importantly, those surveyed also identified the factors which constrain or prevent them from policing licensed premises. Study Two involved interviewing a small but comprehensive group (n=11) of senior managers from within the Queensland Police Service (QPS) who have responsibility for setting operational and strategic policy. The aim of this study was to examine the attitudes, perceptions and influence that senior officers (at the strategy and policy-setting level) had on the officers at the operational level. This qualitative study was carried out using a purposive sampling (Denzin & Lincoln, 2005; Guba & Lincoln, 1989), focused interview and thematic analytic approach. The interview participants were drawn from three tiers of management at district, regional as well as the whole-of-organisational level. The first key theme emerging from the study related to role, in terms of both the QPS broader organisational role, and the individual officer role with respect to the policing of licensed premises. For the QPS organisational role, participants at all three strategic levels had a high degree of congruity as to the organisations service role; that is, to enhance public safety. With respect to participants’ beliefs as to whether police officers have knowledge and understanding of their individual roles concerning licensed premises (as opposed to the QPS role), participants reported most commonly that officers had a reasonable to clear understanding of their role. Participant comments also were supportive of the view that officers operating in the research area, Brisbane Central District (BCD), had a clearer understanding of their role than police operating in other locations. The second key theme to emerge identified a disparity between the knowledge and capability of specialist police, compared with general duties police, to police licensed premises. In fact, a number of the responses to a variety of questions differentiated specialist and general police in a range of domains. One such example related to the clarity of understanding of officer role. Participants agreed that specialist police (Liquor Enforcement & Proactive Strategies [LEAPS] officers) had more clarity of understanding in terms of their role than generalist police. Participants also were strongly of the opinion that specialist police had higher skill levels to deal with issues both inside and outside licensed premises. Some participants expressed the view that general duty police undertook purely response-related activities, or alternatively, dealt with lower order matters. Conversely, it was viewed that specialist police undertook more complex tasks because of their higher levels of knowledge and skill. The third key theme to emerge concerned the identification of barriers that serve to restrict or prevent police officers from policing licensed premises. Participant responses strongly indicated that there was a diversity of resourcing barriers that restrict police from undertaking their roles in licensed premises. Examples of such barriers were the lack of police and the low ratio of police to patrons, available officer time, and lack of organisational investment in skills and knowledge acquisition. However, some participants indicated that police resourcing in the BCD was appropriate and officers were equipped with sufficient powers (policy and legislation). Again, the issue of specialist police was raised by one participant who argued that increasing the numbers of specialist police would ameliorate the difficulties for police officers policing licensed premises. The fourth and last key theme to emerge from Study Two related to the perception of senior officers regarding the opportunity and capability of officers to leverage off external partnerships to reduce harms inside and outside licensed premises. Police working in partnership in BCD was seen as an effective harm reduction strategy and strongly supported by the participants. All participants demonstrated a high degree of knowledge as to who these partners were and could identify those government, non-government and community groups precisely. Furthermore, the majority of participants also held strong views that the partnerships were reasonably effective and worked to varying degrees depending on the nature of the partnership and issues such as resourcing. These senior officers identified better communication and coordination as factors that could potentially strengthen these partnerships. This research finding is particularly important for senior officers who have the capacity to shape the policy and strategic direction of the police service, not only in Queensland but throughout Australasia. Study Three examined the perceptions of those with links to the broader liquor industry (government, non-government and community but exclusive of police) concerning their understanding of the police role and the capacity of police to reduce alcohol-related harm inside and outside licensed premises, and their attitudes towards police. Participants (n=26) surveyed represented a range of areas including the liquor industry, business represenatives and government representatives from Queensland Fire and Rescue Service, Queensland Ambulance Service, Brisbane City Council and Queensland Health. The first key theme to emerge from Study Three related to participant understanding of the QPS organisational role, and importantly, individual officer role in policing licensed premises. In terms of participant understanding of the QPS role there was a clear understanding by the majority of participants that the police role was to act in ways consistent with the law and to otherwise engage in a range of enforcement-related activities. Participants saw such activities falling into two categories. The first category related to reactive policing, which included actions around responding to trouble in licensed premises, monitoring crowd controllers and removing trouble-makers. In the second category, proactive approaches, participants identified the following activities as consistent with that approach: early intervention with offenders, support of licensed premises operators and high visibility policing. When participants were asked about their understanding of individual officer roles in the policing of licensed premises, a range of responses were received but the consistent message that emerged was that there is a different role to be played by general duty (uniformed) police compared to specialist (LEAPS Unit) police, which reflects differences in knowledge, skill and capability. The second key theme that emerged from the data related to the external participants’ views of the knowledge and capability of specialist police, compared with general duty police, to police licensed premises. As noted in the first key theme, participants were universally of the view that the knowledge, skill and capability of police in specialist units (LEAPS Unit) was at a higher level than that of general duty police. Participants observed that these specialist officers were better trained than their colleagues in generalist areas and were therefore better able to intervene knowledgeably and authoritatively to deal with problems and issues as they emerged. Participants also reported that officers working within BCD generally had a positive attitude to their duties and had important local knowledge that they could use in the resolution of alcohol-related issues. Participants also commented on the importance of sound and effective QPS leadership, as well as the quality of the leadership in BCD. On both these measures, there was general consensus from participants, who reported positively on the importance and effectiveness of such leadership in BCD. The third key theme to emerge from Study Three concerned the identification of barriers that serve to restrict or prevent police officers from policing licensed premises. Overwhelmingly, external participants reported the lack of human resources (i.e. police officers) as the key barrier. Other resourcing limitations, such as available officer time, police computer systems, and the time taken to charge offenders, were identified as barriers. Some participants identified barriers in the liquor industry such as ‘dodgy operators’ and negative media attention as limitations. Other constraints to emerge related to government and policy barriers. These were reflected in comments about the collection by government of fees from licensees and better ‘powers’ for police to deal with offenders. The fourth and final key theme that emerged from Study Three related to the opportunities for and capability of police to leverage off external partnerships to reduce harms inside and outside licensed premises. Not surprisingly, participants had a comprehensive knowledge of a broad range of stakeholders, from a diversity of contexts, influential in addressing issues in licensed premises. Many participants reported their relationships with the police and other stakeholders as effective, productive and consistent with the objectives of partnering to reduce alcohol-related harm. On the other hand, there were those who were concerned with their relationship with other stakeholders, particularly those with a compliance function (e.g. Office of Liquor & Gaming Regulation [OLGR]). The resourcing limitations of partners and stakeholders were also raised as an important constraining factor in fulfilling the optimum relationship. Again, political issues were mentioned in terms of the impact on partnerships, with participants stating that there is at times political interference and that politicians complicate the relationships of stakeholders. There are some significant strengths with respect to the methodology of this research. The research is distinguished from previous work in that it examines these critical issues from three distinct perspectives (i.e. police officer, senior manager and external stakeholder). Other strengths relate to the strong theoretical framework that guides and informs the research. There are also some identified limitations, including the subjective nature of self-report data as well as the potential for bias by the author, which was controlled for using a range of initiatives. A further limitation concerns the potential for transferability and generalisability of the findings to other locations given the distinctive nature of the BCD. These limitations and issues of transferability are dealt with at length in the thesis. Despite a growing body of literature about contextual harms associated with alcohol, and specific research concerning police intervention in such contextual harms, there is still much to learn. While research on the subject of police engaging in alcohol-related incidents has focused on police behaviours and strategies in response to such issues, there is a paucity of research that focuses on the knowledge and understanding of officers engaged in such behaviours and practices. Given the scarcity of research dealing with the knowledge, skills and attitudes of police officers responding to harms inside and outside licensed premises, this research contributes significantly to what is a recent and growing body of research and literature in the field. The research makes a practical contribution to police agencies’ understanding of officer knowledge and police practice in ways that have the potential to shape education and training agendas, policy approaches around generalist versus specialist policing, strategic and operational strategy, as well as partnership engagements. The research also makes a theoretical contribution given that the research design is informed by the Three Circle

The beliefs which influence young males to speed and strategies to slow them down : informing the content of anti-speeding messages

Young male drivers are over-represented in road-related fatalities. Speeding represents a pervasive and significant contributor to road trauma. Anti-speeding messages represent a long-standing strategy aimed at discouraging drivers from speeding. These messages, however, have not always achieved their persuasive objectives which may be due, in part, to them not always targeting the most salient beliefs underpinning the speeding behavior of particular driver groups. The current study elicited key beliefs underpinning speeding behavior as well as strategies used to avoid speeding, using a well-validated belief-based model, the Theory of Planned Behavior and in-depth qualitative methods. To obtain the most comprehensive understanding about the salient beliefs and strategies of young male drivers, how such beliefs and strategies compared with those of drivers of varying ages and gender, was also explored. Overall, 75 males and females (aged 17-25 or 30-55 years) participated in group discussions. The findings revealed beliefs that were particularly relevant to young males and that would likely represent key foci for developing message content. For instance, the need to feel in control and the desire to experience positive affect when driving were salient advantages; while infringements were a salient disadvantage and, in particular, the loss of points and the implications associated with potential licence loss as opposed to the monetary (fine) loss (behavioral beliefs). For normative influences, young males appeared to hold notable misperceptions (compared with other drivers, such as young females); for instance, young males believed that females/girlfriends were impressed by their speeding. In the case of control beliefs, the findings revealed low perceptions of control with respect to being able to not speed and a belief that something “extraordinary” would need to happen for a young male driver to lose control of their vehicle while speeding. The practical implications of the findings, in terms of providing suggestions for devising the content of anti-speeding messages, are discussed.

Influence of ventilation and filtration on indoor particle concentrations in urban office buildings

This study aimed to quantify the efficiency of deep bag and electrostatic filters, and assess the influence of ventilation systems using these filters on indoor fine (<2.5 µm) and ultrafine particle concentrations in commercial office buildings. Measurements and modelling were conducted for different indoor and outdoor particle source scenarios at three office buildings in Brisbane, Australia. Overall, the in-situ efficiency, measured for particles in size ranges 6 to 3000 nm, of the deep bag filters ranged from 26.3 to 46.9% for the three buildings, while the in-situ efficiency of the electrostatic filter in one building was 60.2%. The highest PN and PM2.5 concentrations in one of the office buildings (up to 131% and 31% higher than the other two buildings, respectively) were due to the proximity of the building’s HVAC air intakes to a nearby bus-only roadway, as well as its higher outdoor ventilation rate. The lowest PN and PM2.5 concentrations (up to 57% and 24% lower than the other two buildings, respectively) were measured in a building that utilised both outdoor and mixing air filters in its HVAC system. Indoor PN concentrations were strongly influenced by outdoor levels and were significantly higher during rush-hours (up to 41%) and nucleation events (up to 57%), compared to working-hours, for all three buildings. This is the first time that the influence of new particle formation on indoor particle concentrations has been identified and quantified. A dynamic model for indoor PN concentration, which performed adequately in this study also revealed that using mixing/outdoor air filters can significantly reduce indoor particle concentration in buildings where indoor air was strongly influenced by outdoor particle levels. This work provides a scientific basis for the selection and location of appropriate filters and outdoor air intakes, during the design of new, or upgrade of existing, building HVAC systems. The results also serve to provide a better understanding of indoor particle dynamics and behaviours under different ventilation and particle source scenarios, and highlight effective methods to reduce exposure to particles in commercial office buildings.

An isoviscous, isothermal model investigating the influence of hydrostatic recesses on a spring-supported tilting pad thrust bearing

Tilting-pad hydrodynamic thrust bearings are used in hydroelectric power stations around the world, reliably supporting turbines weighing hundreds of tonnes, over decades of service. Newer designs incorporate hydrostatic recesses machined into the sector-shaped pads to enhance oil film thickness at low rotational speeds. External pressurisation practically eliminates wear and enhances service life and reliability. It follows that older generating plants, lacking such assistance, stand to benefit from being retrofitted with hydrostatic lubrication systems. The design process is not trivial however. The need to increase the groove size to permit spontaneous lifting of the turbine under hydrostatic pressure, conflicts with the need to preserve performance of the original plane pad design. A haphazardly designed recess can induce a significant rise in bearing temperature concomitant with reduced mechanical efficiency and risk of thermal damage. In this work, a numerical study of a sector-shaped pad is undertaken to demonstrate how recess size and shape can affect the performance of a typical bearing.

Equity in estate litigation : setting aside inter vivos transactions post mortem on the grounds of undue influence and unconscionable bargains

Where the value of an estate of a deceased person has been diminished by intervivos transfers of property, equitable doctrines provide powerful tools for practitioners advising those who are seeking to claim benefits under wills (or an intestacy) and those seeking further and better provision from the deceased estate.

Influence of synthesis route on the catalytic properties of La1−xSrxMnO3

Lanthanum Strontium Manganate (LSM) powders were synthesized by six different routes, namely solid state reaction, drip pyrolysis, citrate, sol-gel, carbonate and oxalate co-precipitation. The LSM samples, produced by firing to 1000 °C for 5 h were then characterized by way of XRD, TPD's of oxygen, TPR and catalytic activity for a simple oxidation reaction, that of carbon monoxide to carbon dioxide. It was found that although the six samples had similar compositions and surface areas they performed quite differently during catalytic characterization. These observed differences correlated more closely to the mode of synthesis, than to the physical properties of the powders, or their impurity levels, indicating that the surface structures created by the different syntheses perform very differently under catalysis conditions. Co-precipitation and drip pyrolysis produced structures that were most efficient at facilitating oxidation type reactions.

Influence of oxidation and reduction conditions upon the morphology of silica-supported polycrystalline silver catalysts

The effect of oxidation and reduction conditions upon the morphology of polycrystalline silver catalysts has been investigated by means of in situ Fourier-transform infrared (FTIR) spectroscopy. Characterization of the sample was achieved by inspection of the νas(COO) band profile of adsorbed formate, recorded after dosing with formic acid at ambient temperature. Evidence was obtained for the existence of a silver surface reconstructed by the presence of subsurface oxygen in addition to the conventional family of Ag(111) and Ag(110) crystal faces. Oxidation at 773 K facilitated the reconstruction of silver planes due to the formation of subsurface oxygen species. Prolonged oxygen treatment at 773 K also caused particle fragmentation as a consequence of excessive oxygen penetration of the silver catalyst at defect sites. It was also deduced that the presence of oxygen in the gas phase stabilized the growth of silver planes which could form stronger bonds with oxygen. In contrast, high-temperature thermal treatment in vacuum induced significant sintering of the silver catalyst. Reduction at 773 K resulted in substantial quantities of dissolved hydrogen (and probably hydroxy species) in the bulk silver structure. Furthermore, enhanced defect formation in the catalyst was also noted, as evidenced by the increased concentration of formate species associated with oxygen-reconstructed silver faces.

"If they say go faster or something I'll probably go faster" - peer influence upon the risky driving behaviour of young novice drivers

Purpose Young novice drivers are at considerable risk of injury on the road, and their behaviour appears vulnerable to the social influence of their friends. Research was undertaken to identify the nature and mechanisms of peer influence upon novice driver (16-25 years) behaviour to inform the design of more effective young driver countermeasures. Methods. Peer influence was explored in small group interviews (n = 21) and three surveys (n1 = 761, n2 = 1170, n3 = 390) as part of a larger Queensland-wide study. Surveys two and three were part of a six-month longitudinal study. Results Peer influence was reported from the pre-Licence to the Provisional (intermediate) periods. Young novice drivers who experienced or expected social punishments including ‘being told off’ for risky driving reported less riskiness. Conversely young novice drivers who experienced or expected social rewards such as being ‘cheered on’ by their friends – who were also more risky drivers – reported more risky driving including crashes and offences. Conclusions Peers appear influential in the risky behaviour of young novice drivers, and influence occurs through social mechanisms of reinforcement and sanction. Interventions enhancing positive influence and curtailing negative influence may improve road safety outcomes not only for young novice drivers, but for all persons who share the road with them. Among the interventions warranting further development and evaluation are programs to encourage the modelling of safe driving behaviour and attitudes by young drivers; and minimisation of social reinforcement and promotion of social sanctions for risky driving behaviour in particular.

"My mother would freak out" : understanding the influence of parents on the risky behaviour of their young novice drivers

Purpose Parents can influence the driving behaviour of their young novice drivers in a variety of ways. Research was undertaken to explore and identify the nature and mechanisms of parental influence upon novice drivers (16-25 years) to inform the design of more effective young driver countermeasures. Methods The mechanisms and nature of parental influence on young novice drivers were explored in small group interviews (n = 21) and three surveys (n1 = 761, n2 = 1170, n3 = 390) in a larger Queensland-wide study. Surveys two and three were part of a six-month longitudinal study. Results Parental influence appeared to occur across the pre-Licence, Learner, and Provisional (intermediate) periods. The most risky novice drivers (in terms of pre-Licence driving, unsupervised driving while a Learner, and risky driving behaviours such as speeding) reported that their parents were less likely to punish risky driving, and that their parents – who they were more likely to imitate – were also risky drivers (indicated by crashes and offences). Conclusions Parents appear influential in the risky behaviour of young novice drivers. Interventions enhancing their positive influence may improve road safety outcomes not only for young novice drivers, but for all persons who share the road with them. Among the interventions warranting further development and evaluation are programs to encourage the modelling of safe driving behaviour by parents; continued parental monitoring of driving during the pre-Licence, Learner and Provisional periods (e.g., Checkpoints program); and sharing the family vehicle during the first six months of independent licensure.

Influence of osteocytes in the in vitro and in vivo β-tricalcium phosphate-stimulated osteogenesis

Osteocytes, known to act as the main regulators of bone homeostasis, have become a major focus in the field of bone research. Bioactive ceramics have been widely used for bone regeneration. However, there are few studies about the interaction of osteocytes with bioceramics. The effects of osteocytes on the in vitro and in vivo osteogenesis of bioceramics are also unclear. The aim of this study was to investigate the role of osteocytes on the b-tricalcium phosphate (b-TCP) stimulated osteogenesis. It was found that osteocytes responded to the b-TCP stimulation, leading to the release of Wnt (wingless-related MMTV integration site), which enhanced osteogenic differentiation of bone marrow stromal cells via Wnt signaling pathway. Receptor activator of nuclear factor kappa B ligand, an osteoclast inducer, was also upregulated, indicating that osteocytes would also participated in activation of osteoclasts, which played a major role in the degradation process of b-TCP and new bone remodeling. In vivo studies further demonstrated that when the material was completely embedded by newly formed bone, the only cell contacting with the material was osteocyte. However, the material would eventually be degraded and replaced by the new bone, requiring the participation of osteoclasts and osteoblasts, which were demonstrated by using immunostaining in this study. As the only cell contacting with the material, osteocytes probably acted in a regulatory role to regulate the surrounding osteoclasts and osteoblasts. Osteocytes were also found to participate in the maturation of osteoblasts and the mineralization process of biomaterials, by upregulating E11 (podoplanin) and dentin matrix protein 1 expression. These findings indicated that osteocytes involved in bone biomaterial-mediated osteogenesis and biomaterial degradation, providing valuable insights into the mechanism of material-stimulated osteogenesis, and a novel strategy to optimize the evaluating system for the biological properties of biomaterials.

The influence of fatty acid methyl ester profiles on inter-cycle variability in a heavy duty compression ignition engine

With the advent of alternative fuels, such as biodiesels and related blends, it is important to develop an understanding of their effects on inter-cycle variability which, in turn, influences engine performance as well as its emission. Using four methanol trans-esterified biomass fuels of differing carbon chain length and degree of unsaturation, this paper provides insight into the effect that alternative fuels have on inter-cycle variability. The experiments were conducted with a heavy-duty Cummins, turbo-charged, common-rail compression ignition engine. Combustion performance is reported in terms of the following key in-cylinder parameters: indicated mean effective pressure (IMEP), net heat release rate (NHRR), standard deviation of variability (StDev), coefficient of variation (CoV), peak pressure, peak pressure timing and maximum rate of pressure rise. A link is also established between the cyclic variability and oxygen ratio, which is a good indicator of stoichiometry. The results show that the fatty acid structures did not have a significant effect on injection timing, injection duration, injection pressure, StDev of IMEP, or the timing of peak motoring and combustion pressures. However, a significant effect was noted on the premixed and diffusion combustion proportions, combustion peak pressure and maximum rate of pressure rise. Additionally, the boost pressure, IMEP and combustion peak pressure were found to be directly correlated to the oxygen ratio. The emission of particles positively correlates with oxygen content in the fuel as well as in the air-fuel mixture resulting in a higher total number of particles per unit of mass.

Identification of molecular genetic factors that influence migraine

Migraine is a common neurological disorder with a strong genetic basis. However, the complex nature of the disorder has meant that few genes or susceptibility loci have been identified and replicated consistently to confirm their involvement in migraine. Approaches to genetic studies of the disorder have included analysis of the rare migraine subtype, familial hemiplegic migraine with several causal genes identified for this severe subtype. However, the exact genetic contributors to the more common migraine subtypes are still to be deciphered. Genome-wide studies such as genome-wide association studies and linkage analysis as well as candidate genes studies have been employed to investigate genes involved in common migraine. Neurological, hormonal and vascular genes are all considered key factors in the pathophysiology of migraine and are a focus of many of these studies. It is clear that the influence of individual genes on the expression of this disorder will vary. Furthermore, the disorder may be dependent on gene–gene and gene–environment interactions that have not yet been considered. In addition, identifying susceptibility genes may require phenotyping methods outside of the International Classification of Headache Disorders II criteria, such as trait component analysis and latent class analysis to better define the ambit of migraine expression.

Outdoor worker sun protection project : a comprehensive applied research project to demonstrate the effectiveness of sun protection measures which influence high risk outdoor workers in Queensland to adopt sun safe behaviour practices 2010 – 2013

The QUT Outdoor Worker Sun Protection (OWSP) project undertook a comprehensive applied health promotion project to demonstrate the effectiveness of sun protection measures which influence high risk outdoor workers in Queensland to adopt sun safe behaviours. The three year project (2010-2013) was driven by two key concepts: 1) The hierarchy of control, which is used to address risks in the workplace, advocates for six control measures that need to be considered in order of priority (refer to Section 3.4.2); and 2) the Ottawa Charter which recommends five action means to achieve health promotion (refer to Section 2.1). The project framework was underpinned by a participatory action research approach that valued peoples’ input, took advantage of existing skills and resources, and stimulated innovation (refer to Section 4.2). Fourteen workplaces (small and large) with a majority outdoor workforce were recruited across regional Queensland (Darling Downs, Northwest, Mackay and Cairns) from four industries types: 1) building and construction, 2) rural and farming, 3) local government, and 4) public sector. A workplace champion was identified at each workplace and was supported (through resource provision, regular contact and site visits) over a 14 to 18 month intervention period to make sun safety a priority in their workplace. Employees and employers were independently assessed for pre- and postintervention sun protection behaviours. As part of the intervention, an individualised sun safety action plan was developed in conjunction with each workplace to guide changes across six key strategy areas including: 1) Policy (e.g., adopt sun safety practices during all company events); 2) Structural and environmental (e.g., shade on worksites; eliminate or minimise reflective surfaces); 3) Personal protective equipment (PPE) (e.g., trial different types of sunscreens, or wide-brimmed hats); 4) Education and awareness (e.g., include sun safety in inductions and toolbox talks; send reminder emails or text messages to workers);5) Role modelling (e.g., by managers, supervisors, workplace champions and mentors); and 6) Skin examinations (e.g., allow time off work for skin checks). The participatory action process revealed that there was no “one size fits all” approach to sun safety in the workplace; a comprehensive, tailored approach was fundamental. This included providing workplaces with information, resources, skills, know how, incentives and practical help. For example, workplaces engaged in farming complete differing seasonal tasks across the year and needed to prepare for optimal sun safety of their workers during less labour intensive times. In some construction workplaces, long pants were considered a trip hazard and could not be used as part of a PPE strategy. Culture change was difficult to achieve and workplace champions needed guidance on the steps to facilitate this (e.g., influencing leaders through peer support, mentoring and role modelling). With the assistance of the project team the majority of workplaces were able to successfully implement the sun safety strategies contained within their action plans, up skilling them in the evidence for sun safety, how to overcome barriers, how to negotiate with all relevant parties and assess success. The most important enablers to the implementation of a successful action plan were a pro-active workplace champion, strong employee engagement, supportive management, the use of highly visual educational resources, and external support (provided by the project team through regular contact either directly through phone calls or indirectly through emails and e-newsletters). Identified barriers included a lack of time, the multiple roles of workplace champions, (especially among smaller workplaces), competing issues leading to a lack of priority for sun safety, the culture of outdoor workers, and costs or budgeting constraints. The level of sun safety awareness, knowledge, and sun protective behaviours reported by the workers increased between pre-and post-intervention. Of the nine sun protective behaviours that were assessed, the largest changes reported included a 26% increase in workers who “usually or always” wore a broad-brimmed hat, a 20% increase in the use of natural shade, a 19% increase in workers wearing long-sleeved collared shirts, and a 16% increase in workers wearing long trousers.

Multiple sclerosis susceptibility-associated SNPs do not influence disease severity measures in a cohort of Australian MS patients

Recent association studies in multiple sclerosis (MS) have identified and replicated several single nucleotide polymorphism (SNP) susceptibility loci including CLEC16A, IL2RA, IL7R, RPL5, CD58, CD40 and chromosome 12q13–14 in addition to the well established allele HLA-DR15. There is potential that these genetic susceptibility factors could also modulate MS disease severity, as demonstrated previously for the MS risk allele HLA-DR15. We investigated this hypothesis in a cohort of 1006 well characterised MS patients from South-Eastern Australia. We tested the MS-associated SNPs for association with five measures of disease severity incorporating disability, age of onset, cognition and brain atrophy. We observed trends towards association between the RPL5 risk SNP and time between first demyelinating event and relapse, and between the CD40 risk SNP and symbol digit test score. No associations were significant after correction for multiple testing. We found no evidence for the hypothesis that these new MS disease risk-associated SNPs influence disease severity.