Simulation of inplane and out of plane AE source in thin plate

In most materials, short stress waves are generated during the process of plastic deformation, phase transformation, crack formation and crack growth. These phenomena are applied in acoustic emission (AE) for the detection of material defects in a wide spectrum of areas, ranging from nondestructive testing for the detection of materials defects to monitoring of microseismical activity. AE technique is also used for defect source identification and for failure detection. AE waves consist of P waves (primary longitudinal waves), S waves (shear/transverse waves) and Rayleigh (surface) waves as well as reflected and diffracted waves. The propagation of AE waves in various modes has made the determination of source location difficult. In order to use acoustic emission technique for accurate identification of source, an understanding of wave propagation of the AE signals at various locations in a plate structure is essential. Furthermore, an understanding of wave propagation can also assist in sensor location for optimum detection of AE signals along with the characteristics of the source. In real life, as the AE signals radiate from the source it will result in stress waves. Unless the type of stress wave is known, it is very difficult to locate the source when using the classical propagation velocity equations. This paper describes the simulation of AE waves to identify the source location and its characteristics in steel plate as well as the wave modes. The finite element analysis (FEA) is used for the numerical simulation of wave propagation in thin plate. By knowing the type of wave generated, it is possible to apply the appropriate wave equations to determine the location of the source. For a single plate structure, the results show that the simulation algorithm is effective to simulate different stress waves.

Review: acoustic emission technique - opportunities, challenges and current work at QUT

Acoustic emission (AE) is the phenomenon where high frequency stress waves are generated by rapid release of energy within a material by sources such as crack initiation or growth. AE technique involves recording these stress waves by means of sensors placed on the surface and subsequent analysis of the recorded signals to gather information such as the nature and location of the source. AE is one of the several non-destructive testing (NDT) techniques currently used for structural health monitoring (SHM) of civil, mechanical and aerospace structures. Some of its advantages include ability to provide continuous in-situ monitoring and high sensitivity to crack activity. Despite these advantages, several challenges still exist in successful application of AE monitoring. Accurate localization of AE sources, discrimination between genuine AE sources and spurious noise sources and damage quantification for severity assessment are some of the important issues in AE testing and will be discussed in this paper. Various data analysis and processing approaches will be applied to manage those issues.

Drug diffusion from polymeric delivery devices : a problem with two moving boundaries

An existing model for solvent penetration and drug release from a spherically-shaped polymeric drug delivery device is revisited. The model has two moving boundaries, one that describes the interface between the glassy and rubbery states of polymer, and another that defines the interface between the polymer ball and the pool of solvent. The model is extended so that the nonlinear diffusion coefficient of drug explicitly depends on the concentration of solvent, and the resulting equations are solved numerically using a front-fixing transformation together with a finite difference spatial discretisation and the method of lines. We present evidence that our scheme is much more accurate than a previous scheme. Asymptotic results in the small-time limit are presented, which show how the use of a kinetic law as a boundary condition on the innermost moving boundary dictates qualitative behaviour, the scalings being very different to the similar moving boundary problem that arises from modelling the melting of an ice ball. The implication is that the model considered here exhibits what is referred to as ``non-Fickian'' or Case II diffusion which, together with the initially constant rate of drug release, has certain appeal from a pharmaceutical perspective.

Stiffness and damping coefficients of 3-axial groove water lubricated bearing using perturbation technique

A Computational fluid dynamics (CFD) approach is used to model fluid flow in a journal bearing with three equi-spaced axial grooves and supplied with water from one end. Water is subjected to both velocity (Couette) & pressure induced (Poiseuille) flow. The working fluid passing through the bearing clearance generates driving force components that may increase the unstable vibration of the rotor. It is important to know the accurate rotor dynamic force component for predicting the instability of rotor bearing systems. In this paper a study has been made to obtain the stiffness and damping coefficients of 3 axial groove bearing using Perturbation technique.

Construction safety : development of an assessment tool to reduce risk on building sites

Australian construction and building workers are exposed to serious workplace risks - including injury, illness and death - and although there have been improvements in occupational health and safety (OHS) performance over the past 20 years, the injury and fatality rate in the Australian construction industry remains a matter of concern. The concept of safety culture is rapidly being adopted in the industry, including recognising the critical role that organisational leaders play in overall safety performance. This paper reviews recent research in construction safety leadership and provides some examples and applications relevant to risk reduction in the workforce. By focusing on developing safety competency in those that fulfil safety critical roles, and clearly articulating the relevant safety management tasks, leaders can positively influence the organisation’s safety culture. Finally, some promising research on Safety Effectiveness Indicators (SEIs) may be an industry-friendly solution to reducing workplace risks across the industry, by providing a credible, accurate, and timely measure of safety performance.

Narrative therapy for adults with major depressive disorder: Improved symptom and interpersonal outcomes

Abstract This study investigated depressive symptom and interpersonal relatedness outcomes from eight sessions of manualized narrative therapy for 47 adults with major depressive disorder. Post-therapy, depressive symptom improvement (d=1.36) and proportions of clients achieving reliable improvement (74%), movement to the functional population (61%), and clinically significant improvement (53%) were comparable to benchmark research outcomes. Post-therapy interpersonal relatedness improvement (d=.62) was less substantial than for symptoms. Three-month follow-up found maintenance of symptom, but not interpersonal gains. Benchmarking and clinical significance analyses mitigated repeated measure design limitations, providing empirical evidence to support narrative therapy for adults with major depressive disorder. RÉSUMÉ Cette étude a investigué les symptômes dépressifs et les relations interpersonnels d'une thérapie narrative en huit séances chez 47 adultes souffrant d'un trouble dépressif majeur. Après la thérapie, l'amélioration des symptômes dépressifs (d=1.36) et la proportion de clients atteignant un changement significatif (74%), le mouvement vers la population fonctionnelle (61%), enfin l'amélioration clinique significative (53%) étaient comparables aux performances des études de résultats. L'amélioration des relations interpersonnelles (d=0.62) était inférieure à l'amélioration symptomatique. Le suivi à trois mois montrait un maintien des gains symptomatiques mais pas pour les relations interpersonnelles. L’évaluation des performances et les analyses de significativité clinique modèrent les limitations du plan de recherche à mesures répétées et apportent une preuve empirique qui étaie l'efficacité des thérapies narratives pour des adultes avec un trouble dépressif majeur. Este estudo investigou sintomas depressivos e resultados interpessoais relacionados em oito sessões de terapia narrativa manualizada para 47 adultos com perturbação depressiva major. No pós terapia, melhoria de sintomas depressivos (d=1,36) e proporção de clientes que alcançam melhoria válida (74%), movimento para a população funcional (61%) e melhoria clinicamente significativa (53%) foram comparáveis com os resultados da investigação reportados. As melhorias pós terapia nos resultados interpessoais relacionados (d=.62) foi menos substancial do que para os sintomas. Aos três meses de seguimento houve a manutenção dos sintomas mas não dos ganhos interpessoais. As análises de benchemarking e de melhoria clinicamente significativas atenuam as limitações de um design de medidas repetidas, fornecendo evidência empírica para a terapia narrativa para adultos com perturbação depressiva major. Questo lavoro ha valutato i sintomi depressivi e gli outcome nella capacità di relazionarsi a livello interpersonale in 8 sedute di psicoterapia narrativa manualizzata in un gruppo di 47 adulti con depressione maggiore. I risultati ottenuti relativamente a: post terapy, miglioramento dei sintomi depressivi (d_1.36), proporzione di pazienti che hanno raggiunto un miglioramento affidabile e consistente (74%), movimento verso il funzionamento atteso nella popolazione (61%) e miglioramento clinicamente significativo (53%) sono paragonabili ai valori di riferimento della ricerca sull'outcome. I miglioramento della capacità di relazionarsi valutata alla fine del trattamento (d_.62) si è rivelata meno sostanziale rispetto ai sintomi. Un follow-up dopo 3 mesi ha dimostrato che il miglioramento sintomatologico è stato mantenuto, ma non quello degli obiettivi interpersonali. Valori di riferimento e analisi della significatività clinica hanno fatto fronte ai limiti del disegno a misure ripetute, offrendo prove empiriche sulla rilevanza della terapia narrativa in pazienti adulti con depressione maggiore

Probability distributed time delays: integrating spatial effects into temporal models

Background In order to provide insights into the complex biochemical processes inside a cell, modelling approaches must find a balance between achieving an adequate representation of the physical phenomena and keeping the associated computational cost within reasonable limits. This issue is particularly stressed when spatial inhomogeneities have a significant effect on system's behaviour. In such cases, a spatially-resolved stochastic method can better portray the biological reality, but the corresponding computer simulations can in turn be prohibitively expensive. Results We present a method that incorporates spatial information by means of tailored, probability distributed time-delays. These distributions can be directly obtained by single in silico or a suitable set of in vitro experiments and are subsequently fed into a delay stochastic simulation algorithm (DSSA), achieving a good compromise between computational costs and a much more accurate representation of spatial processes such as molecular diffusion and translocation between cell compartments. Additionally, we present a novel alternative approach based on delay differential equations (DDE) that can be used in scenarios of high molecular concentrations and low noise propagation. Conclusions Our proposed methodologies accurately capture and incorporate certain spatial processes into temporal stochastic and deterministic simulations, increasing their accuracy at low computational costs. This is of particular importance given that time spans of cellular processes are generally larger (possibly by several orders of magnitude) than those achievable by current spatially-resolved stochastic simulators. Hence, our methodology allows users to explore cellular scenarios under the effects of diffusion and stochasticity in time spans that were, until now, simply unfeasible. Our methodologies are supported by theoretical considerations on the different modelling regimes, i.e. spatial vs. delay-temporal, as indicated by the corresponding Master Equations and presented elsewhere.

Numerical modelling of light gauge cold-formed steel compression members subjected to distortional buckling at elevated temperatures

Fire safety design of building structures has received greater attention in recent times due to continuing loss of properties and lives during fires. However, fire performance of light gauge cold-formed steel structures is not well understood despite its increased usage in buildings. Cold-formed steel compression members are susceptible to various buckling modes such as local and distortional buckling and their ultimate strength behaviour is governed by these buckling modes. Therefore a research project based on experimental and numerical studies was undertaken to investigate the distortional buckling behaviour of light gauge cold-formed steel compression members under simulated fire conditions. Lipped channel sections with and without additional lips were selected with three thicknesses of 0.6, 0.8, and 0.95 mm and both low and high strength steels (G250 and G550 steels). More than 150 compression tests were undertaken first at ambient and elevated temperatures. Finite element models of the tested compression members were then developed by including the degradation of mechanical properties with increasing temperatures. Comparison of finite element analysis and experimental results showed that the developed finite element models were capable of simulating the distortional buckling and strength behaviour at ambient and elevated temperatures up to 800 °C. The validated model was used to determine the effects of mechanical properties, geometric imperfections and residual stresses on the distortional buckling behaviour and strength of cold-formed steel columns. This paper presents the details of the numerical study and the results. It demonstrated the importance of using accurate mechanical properties at elevated temperatures in order to obtain reliable strength characteristics of cold-formed steel columns under fire conditions.

Laser doppler imaging in a paediatric burns population

Objective Laser Doppler imaging (LDI) was compared to wound outcomes in children's burns, to determine if the technology could be used to predict these outcomes. Methods Forty-eight patients with a total of 85 burns were included in the study. Patient median age was 4 years 10 months and scans were taken 0–186 h post-burn using the fast, low-resolution setting on the Moor LDI2 laser Doppler imager. Wounds were managed by standard practice, without taking into account the scan results. Time until complete re-epithelialisation and whether or not grafting and scar management were required were recorded for each wound. If wounds were treated with Silvazine™ or Acticoat™ prior to the scan, this was also recorded. Results The predominant colour of the scan was found to be significantly related to the re-epithelialisation, grafting and scar management outcomes and could be used to predict those outcomes. The prior use of Acticoat™ did not affect the scan relationship to outcomes, however, the use of Silvazine™ did complicate the relationship for light blue and green scanned partial thickness wounds. Scans taken within the 24-h window after-burn also appeared to be accurate predictors of wound outcome. Conclusion Laser Doppler imaging is accurate and effective in a paediatric population with a low-resolution fast-scan.

Omissions, causation and responsibility

In this paper I discuss a recent exchange of articles between Hugh McLachlan and John Coggon on the relationship between omissions, causation and moral responsibility. My aim is to contribute to their debate by isolating a presupposition I believe they both share, and by questioning that presupposition. The presupposition is that, at any given moment, there are countless things that I am omitting to do. This leads them both to give a distorted account of the relationship between causation and moral or (as the case may be) legal responsibility, and, in the case of Coggon, to claim that the law’s conception of causation is a fiction based on policy. Once it is seen that this presupposition is faulty, we can attain a more accurate view of the logical relationship between causation and moral responsibility in the case of omissions. This is important because it will enable us, in turn, to understand why the law continues to regard omissions as different, both logically and morally, from acts, and why the law seeks to track that logical and moral difference in the legal distinction it draws between withholding life-sustaining measures and euthanasia.

A mass-conservative control volume-finite element method for solving Richards’ equation in heterogeneous porous media

We present a mass-conservative vertex-centred finite volume method for efficiently solving the mixed form of Richards’ equation in heterogeneous porous media. The spatial discretisation is particularly well-suited to heterogeneous media because it produces consistent flux approximations at quadrature points where material properties are continuous. Combined with the method of lines, the spatial discretisation gives a set of differential algebraic equations amenable to solution using higher-order implicit solvers. We investigate the solution of the mixed form using a Jacobian-free inexact Newton solver, which requires the solution of an extra variable for each node in the mesh compared to the pressure-head form. By exploiting the structure of the Jacobian for the mixed form, the size of the preconditioner is reduced to that for the pressure-head form, and there is minimal computational overhead for solving the mixed form. The proposed formulation is tested on two challenging test problems. The solutions from the new formulation offer conservation of mass at least one order of magnitude more accurate than a pressure head formulation, and the higher-order temporal integration significantly improves both the mass balance and computational efficiency of the solution.

Statistical analyses of weigh-in-motion data for bridge live load development

This paper discusses the statistical analyses used to derive bridge live loads models for Hong Kong from a 10-year weigh-in-motion (WIM) data. The statistical concepts required and the terminologies adopted in the development of bridge live load models are introduced. This paper includes studies for representative vehicles from the large amount of WIM data in Hong Kong. Different load affecting parameters such as gross vehicle weights, axle weights, axle spacings, average daily number of trucks etc are first analyzed by various stochastic processes in order to obtain the mathematical distributions of these parameters. As a prerequisite to determine accurate bridge design loadings in Hong Kong, this study not only takes advantages of code formulation methods used internationally but also presents a new method for modelling collected WIM data using a statistical approach.

A qualitative study of older adults’ responses to sitting-time questions : do we get the information we want?

Background: In the last decade, there has been increasing interest in the health effects of sedentary behavior, which is often assessed using self-report sitting-time questions. The aim of this qualitative study was to document older adults’ understanding of sitting-time questions from the International Physical Activity (PA) Questionnaire (IPAQ) and the PA Scale for the Elderly (PASE). Methods: Australian community-dwelling adults aged 65+ years answered the IPAQ and PASE sitting questions in face-to-face semi-structured interviews. IPAQ uses one open-ended question to assess sitting on a weekday in the last 7 days 'at work, at home, while doing coursework and during leisure time'; PASE uses a three-part closed question about daily leisure-time sitting in the last 7 days. Participants expressed their thoughts out loud while answering each question. They were then probed about their responses. Interviews were recorded, transcribed and coded into themes. Results: Mean age of the 28 male and 27 female participants was 73 years (range 65-89). The most frequently reported activity was watching TV. For both questionnaires, many participants had difficulties understanding what activities to report. Some had difficulty understanding what activities should be classified as ‘leisure-time sitting’. Some assumed they were being asked to only report activities provided as examples. Most reported activities they normally do, rather than those performed on a day in the previous week. Participants used a variety of strategies to select ‘a day’ for which they reported their sitting activities and to calculate sitting time on that day. Therefore, many different ways of estimating sitting time were used. Participants had particular difficulty reporting their daily sitting-time when their schedules were not consistent across days. Some participants declared the IPAQ sitting question too difficult to answer. Conclusion: The accuracy of older adults’ self-reported sitting time is questionable given the challenges they have in answering sitting-time questions. Their responses to sitting-time questions may be more accurate if our recommendations for clarifying the sitting domains, providing examples relevant to older adults and suggesting strategies for formulating responses are incorporated. Future quantitative studies should include objective criterion measures to assess validity and reliability of these questions.

The 'nurdle to leg' and other ways of winning cricket matches

The emergence of Twenty20 cricket at the elite level has been marketed on the excitement of the big hitter, where it seems that winning is a result of the muscular batter hitting boundaries at will. This version of the game has captured the imagination of many young players who all want to score runs with “big hits”. However, in junior cricket, boundary hitting is often more difficult due to size limitations of children and games played on outfields where the ball does not travel quickly. As a result, winning is often achieved via a less spectacular route – by scoring more singles than your opponents. However, most standard coaching texts only describe how to play boundary scoring shots (e.g. the drives, pulls, cuts and sweeps) and defensive shots to protect the wicket. Learning to bat appears to have been reduced to extremes of force production, i.e. maximal force production to hit boundaries or minimal force production to stop the ball from hitting the wicket. Initially, this is not a problem because the typical innings of a young player (<12 years) would be based on the concept of “block” or “bash” – they “block” the good balls and “bash” the short balls. This approach works because there are many opportunities to hit boundaries off the numerous inaccurate deliveries of novice bowlers. Most runs are scored behind the wicket by using the pace of the bowler’s delivery to re-direct the ball, because the intrinsic dynamics (i.e. lack of strength) of most children means that they can only create sufficient power by playing shots where the whole body can contribute to force production. This method works well until the novice player comes up against more accurate bowling when they find they have no way of scoring runs. Once batters begin to face “good” bowlers, batters have to learn to score runs via singles. In cricket coaching manuals (e.g. ECB, n.d), running between the wickets is treated as a separate task to batting, and the “basics” of running, such as how to “back- up”, carry the bat, calling and turning and sliding the bat into the crease are “drilled” into players. This task decomposition strategy focussing on techniques is a common approach to skill acquisition in many highly traditional sports, typified in cricket by activities where players hit balls off tees and receive “throw-downs” from coaches. However, the relative usefulness of these approaches in the acquisition of sporting skills is increasingly being questioned (Pinder, Renshaw & Davids, 2009). We will discuss why this is the case in the next section.

The changing face of practice for developing perception : action skill in cricket

The use of bowling machines is common practice in cricket. In an ideal world all batters would face real bowlers in practice sessions, but this is not always possible, for many reasons. The clear advantage of using bowling machines is that they alleviate the workload required from bowlers (Dennis, Finch & Farhart, 2005) and provide relatively consistent and accurate ball delivery which may not be otherwise available to many young batters. Anecdotal evidence suggests that many, if not most of the world’s greatest players use these methods within their training schedules. For example, Australian internationals, Michael Hussey and Matthew Hayden extensively used bowling machines (Hussey & Sygall, 2007). Bowling machines enable batsmen to practice for long periods, developing their endurance and concentration. However, despite these obvious benefits, in recent times the use of bowling machines has been questioned by sport scientists, coaches, ex- players and commentators. For example, Hussey’s batting coach comments “…we never went near a bowling machine in [Michael’s] first couple of years, I think there’s something to that …” (Hussey & Sygall, 2007, p. 119). This chapter will discuss the efficacy of using bowling machines with reference to research findings, before reporting new evidence that provides support for an alternative, innovative and possibly more representative practice design. Finally, the chapter will provide advice for coaches on the implications of this research, including a case study approach to demonstrate the practical use of such a design.