FPGA implementation of an evolutionary algorithm for autonomous unmanned aerial vehicle on-board path planning

In this paper, a hardware-based path planning architecture for unmanned aerial vehicle (UAV) adaptation is proposed. The architecture aims to provide UAVs with higher autonomy using an application specific evolutionary algorithm (EA) implemented entirely on a field programmable gate array (FPGA) chip. The physical attributes of an FPGA chip, being compact in size and low in power consumption, compliments it to be an ideal platform for UAV applications. The design, which is implemented entirely in hardware, consists of EA modules, population storage resources, and three-dimensional terrain information necessary to the path planning process, subject to constraints accounted for separately via UAV, environment and mission profiles. The architecture has been successfully synthesised for a target Xilinx Virtex-4 FPGA platform with 32% logic slices utilisation. Results obtained from case studies for a small UAV helicopter with environment derived from LIDAR (Light Detection and Ranging) data verify the effectiveness of the proposed FPGA-based path planner, and demonstrate convergence at rates above the typical 10 Hz update frequency of an autopilot system.

The effect of lumbar support on the trunk muscle activity and pelvic tilt in a passenger vehicle car seat

In order to gain a competitive edge in the market, automotive manufacturers and automotive seat suppliers have identified seat ergonomics for further development to improve overall vehicle comfort. Adjustable lumbar support devices have been offered since long as comfort systems in either a 2-way or 4-way adjustable configuration, although their effect on lumbar strain is not well documented. The effect of a lumbar support on posture and muscular strain, and therefore the relationship between discomfort and comfort device parameter settings, requires clarification. The aim of this paper is to study the effect of a 4-way lumbar support on lower trunk and pelvis muscle activity, pelvic tilt and spine curvature during a car seating activity. 10 healthy subjects (5 m/f; age 19-39) performed a seating activity in a passenger vehicle with seven different static lumbar support positions. The lumbar support was tested in 3 different height positions in relation to the seatback surface centreline (high, centre, low), each having 2 depths positions (lumbar prominence). An extra depth position was added for the centre position. Posture data were collected using a VICON MX motion capture system and NORAXON DTS goniometers and inclinometer. A rigid-body model of an adjustable car seat with four-way adjustable lumbar support was constructed in UGS Siemens NX and connected to a musculoskeletal model of a seated-human, modelled in AnyBody. Wireless electromyography (EMG) was used to calibrate the musculoskeletal model and assess the relationship between (a) muscular strain and lumbar prominence (normal to seatback surface) respective to the lumbar height (alongside seatback surface), (b) hip joint moment and lumbar prominence (normal to seatback surface) respective to lumbar height (alongside seatback surface) and (c) pelvic tilt and lumbar prominence (normal to seatback surface) respective to the lumbar height (alongside seatback surface). This study was based on the assumption that the musculoskeletal human model was seated at the correct R-Point (SgRP), determined via the occupant packaging toolkit in the JACK digital human model. The effect of the interaction between the driver/car-seat has been investigated for factors resulting from the presence and adjustment of a 4-way lumbar support. The results obtained show that various seat adjustments, and driver’s lumbar supports can have complex influence on the muscle activation, joint forces and moments, all of which can affect the comfort perception of the driver. This study enables the automotive industry to optimise passenger vehicle seat development and design. It further more supports the evaluation of static postural and dynamic seat comfort in normal everyday driving tasks and can be applied for future car design to reduce investment and improve comfort.

Digital human modelling for vehicle design and manufacturing

Digital human modelling (DHM) has today matured from research into industrial application. In the automotive domain, DHM has become a commonly used tool in virtual prototyping and human-centred product design. While this generation of DHM supports the ergonomic evaluation of new vehicle design during early design stages of the product, by modelling anthropometry, posture, motion or predicting discomfort, the future of DHM will be dominated by CAE methods, realistic 3D design, and musculoskeletal and soft tissue modelling down to the micro-scale of molecular activity within single muscle fibres. As a driving force for DHM development, the automotive industry has traditionally used human models in the manufacturing sector (production ergonomics, e.g. assembly) and the engineering sector (product ergonomics, e.g. safety, packaging). In product ergonomics applications, DHM share many common characteristics, creating a unique subset of DHM. These models are optimised for a seated posture, interface to a vehicle seat through standardised methods and provide linkages to vehicle controls. As a tool, they need to interface with other analytic instruments and integrate into complex CAD/CAE environments. Important aspects of current DHM research are functional analysis, model integration and task simulation. Digital (virtual, analytic) prototypes or digital mock-ups (DMU) provide expanded support for testing and verification and consider task-dependent performance and motion. Beyond rigid body mechanics, soft tissue modelling is evolving to become standard in future DHM. When addressing advanced issues beyond the physical domain, for example anthropometry and biomechanics, modelling of human behaviours and skills is also integrated into DHM. Latest developments include a more comprehensive approach through implementing perceptual, cognitive and performance models, representing human behaviour on a non-physiologic level. Through integration of algorithms from the artificial intelligence domain, a vision of the virtual human is emerging.

PySSM : a Python module for Bayesian inference of linear Gaussian state space models

PySSM is a Python package that has been developed for the analysis of time series using linear Gaussian state space models (SSM). PySSM is easy to use; models can be set up quickly and efficiently and a variety of different settings are available to the user. It also takes advantage of scientific libraries Numpy and Scipy and other high level features of the Python language. PySSM is also used as a platform for interfacing between optimised and parallelised Fortran routines. These Fortran routines heavily utilise Basic Linear Algebra (BLAS) and Linear Algebra Package (LAPACK) functions for maximum performance. PySSM contains classes for filtering, classical smoothing as well as simulation smoothing.

Place and Space: Community in the Internet Economy and What This Will Mean for Property

By 2020 Australia‟s National Digital Economy Strategy aims to increase household online participation and engage 12 per cent of all employees in teleworking arrangements. Achieving these goals is generally perceived as positive due to the reduced impact on the natural environment from less use of transport. However, this also will enable greater flexibility as to where people live and thus will impact upon the maintenance and formation of communities and on property use. This paper commences by clarifying what is Australia‟s internet economy before highlighting the impact of the internet on community formation and maintenance. The paper concludes by identifying what the achievement of these goals will mean for property use in the future.

Commentaries and Responses to "The Driver Behaviour Questionnaire as a predictor of accidents: A meta-analysis" [Commentaries lead by Anders af Wahlberg; Responses lead by J.C.F. de Winter]

The following discussion is in response to a 2010 article published in the Journal of Safety Research by J.C.F. de Winter and D. Dodou entitled “The Driver Behaviour Questionnaire as a predictor of accidents: A meta-analysis” (Volume 41, Number 6, pp. 463-470, available on sciencedirect.com). The editors are pleased to provide a forum for this exchange and welcome further comments.

A simulation study of unified GPS and roadside ranging technologies for vehicle positioning

The future vehicle navigation for safety applications requires seamless positioning at the accuracy of sub-meter or better. However, standalone Global Positioning System (GPS) or Differential GPS (DGPS) suffer from solution outages while being used in restricted areas such as high-rise urban areas and tunnels due to the blockages of satellite signals. Smoothed DGPS can provide sub-meter positioning accuracy, but not the seamless requirement. A disadvantage of the traditional navigation aids such as Dead Reckoning and Inertial Measurement Unit onboard vehicles are either not accurate enough due to error accumulation or too expensive to be acceptable by the mass market vehicle users. One of the alternative technologies is to use the wireless infrastructure installed in roadside to locate vehicles in regions where the Global Navigation Satellite Systems (GNSS) signals are not available (for example: inside tunnels, urban canyons and large indoor car parks). The examples of roadside infrastructure which can be potentially used for positioning purposes could include Wireless Local Area Network (WLAN)/Wireless Personal Area Network (WPAN) based positioning systems, Ultra-wide band (UWB) based positioning systems, Dedicated Short Range Communication (DSRC) devices, Locata’s positioning technology, and accurate road surface height information over selected road segments such as tunnels. This research reviews and compares the possible wireless technologies that could possibly be installed along roadside for positioning purposes. Models and algorithms of integrating different positioning technologies are also presented. Various simulation schemes are designed to examine the performance benefits of united GNSS and roadside infrastructure for vehicle positioning. The results from these experimental studies have shown a number of useful findings. It is clear that in the open road environment where sufficient satellite signals can be obtained, the roadside wireless measurements contribute very little to the improvement of positioning accuracy at the sub-meter level, especially in the dual constellation cases. In the restricted outdoor environments where only a few GPS satellites, such as those with 45 elevations, can be received, the roadside distance measurements can help improve both positioning accuracy and availability to the sub-meter level. When the vehicle is travelling in tunnels with known heights of tunnel surfaces and roadside distance measurements, the sub-meter horizontal positioning accuracy is also achievable. Overall, simulation results have demonstrated that roadside infrastructure indeed has the potential to provide sub-meter vehicle position solutions for certain road safety applications if the properly deployed roadside measurements are obtainable.

Doing blog research

Blogs and other online platforms for personal writing such as LiveJournal have been of interest to researchers across the social sciences and humanities for a decade now. Although growth in the uptake of blogging has stalled somewhat since the heyday of blogs in the early 2000s, blogging continues to be a major genre of Internet-based communication. Indeed, at the same time that mass participation has moved on to Facebook, Twitter, and other more recent communication phenomena, what has been left behind by the wave of mass adoption is a slightly smaller but all the more solidly established blogosphere of engaged and committed participants. Blogs are now an accepted part of institutional, group, and personal communications strategies (Bruns and Jacobs, 2006); in style and substance, they are situated between the more static information provided by conventional Websites and Webpages and the continuous newsfeeds provided through Facebook and Twitter updates. Blogs provide a vehicle for authors (and their commenters) to think through given topics in the space of a few hundred to a few thousand words – expanding, perhaps, on shorter tweets, and possibly leading to the publication of more fully formed texts elsewhere. Additionally, they are also a very flexible medium: they readily provide the functionality to include images, audio, video, and other additional materials – as well as the fundamental tool of blogging, the hyperlink itself. Indeed, the role of the link in blogs and blog posts should not be underestimated. Whatever the genre and topic that individual bloggers engage in, for the most part blogging is used to provide timely updates and commentary – and it is typical for such material to link both to relevant posts made by other bloggers, and to previous posts by the present author, both to background material which provides readers with further information about the blogger’s current topic, and to news stories and articles which the blogger found interesting or worthy of critique. Especially where bloggers are part of a larger community of authors sharing similar interests or views (and such communities are often indicated by the presence of yet another type of link – in blogrolls, often in a sidebar on the blog site, which list the blogger’s friends or favourites), then, the reciprocal writing and linking of posts often constitutes an asynchronous, distributed conversation that unfolds over the course of days, weeks, and months. Research into blogs is interesting for a variety of reasons, therefore. For one, a qualitative analysis of one or several blogs can reveal the cognitive and communicative processes through which individual bloggers define their online identity, position themselves in relation to fellow bloggers, frame particular themes, topics and stories, and engage with one another’s points of view. It may also shed light on how such processes may differ across different communities of interest, perhaps in correlation with the different societal framing and valorisation of specific areas of interest, with the socioeconomic backgrounds of individual bloggers, or with other external or internal factors. Such qualitative research now looks back on a decade-long history (for key collections, see Gurak, et al., 2004; Bruns and Jacobs, 2006; also see Walker Rettberg, 2008) and has recently shifted also to specifically investigate how blogging practices differ across different cultures (Russell and Echchaibi, 2009). Other studies have also investigated the practices and motivations of bloggers in specific countries from a sociological perspective, through large-scale surveys (e.g. Schmidt, 2009). Blogs have also been directly employed within both K-12 and higher education, across many disciplines, as tools for reflexive learning and discussion (Burgess, 2006).

Redland city youth and public space report : provisions for good practice

Written for Redland City Council in collaboration with the Capalaba Stakeholders Group. The provisions detailed in this report constitute a protocol agreement developed through the Capalaba Stakeholders Group between 2009 and 2011 around young people and public spaces in Redland City, Queensland. These provisions include agreed principles, standards and responses to tensions or unacceptable behaviour, how various tensions and problems can be resolved in constructive ways and how people, including young people can work together to make a public or community accessed space safe and accessible. It is based on the recognition that young people are part of the community and that strategies to resolve tensions that arise should be inclusive and employ a mixed methods approach.

A Context Space Model for Detecting Anomalous Behaviour in Video Surveillance

Having a good automatic anomalous human behaviour detection is one of the goals of smart surveillance systems’ domain of research. The automatic detection addresses several human factor issues underlying the existing surveillance systems. To create such a detection system, contextual information needs to be considered. This is because context is required in order to correctly understand human behaviour. Unfortunately, the use of contextual information is still limited in the automatic anomalous human behaviour detection approaches. This paper proposes a context space model which has two benefits: (a) It provides guidelines for the system designers to select information which can be used to describe context; (b)It enables a system to distinguish between different contexts. A comparative analysis is conducted between a context-based system which employs the proposed context space model and a system which is implemented based on one of the existing approaches. The comparison is applied on a scenario constructed using video clips from CAVIAR dataset. The results show that the context-based system outperforms the other system. This is because the context space model allows the system to considering knowledge learned from the relevant context only.

Living with strangers: Urban space and the ethics of civility

Urban regeneration is occuring in cities across the world, as cities increase in scale and complexity. This chapter argues that in planning public spaces, greater consideration should be paid to sociability through consideration of the affective dimension of urban life.

"The greatest harbour in the world" : Sydney Harbour as a contested space in Australian culture

It is a matter of public record that the former Prime Minister of Australia, the Honourable Paul Keating, upset certain Australian architects with his intervention into the redevelopment of the 22-hectare “Barangaroo” site on Sydney Harbour. While Keating’s intervention continues to provide engaging theatre for Sydney residents the debate is also an interesting expression of the narrative of contestation that has been played out historically about the waters of Sydney Harbour. From a cultural studies perspective, the Harbour, and the Sydney Harbour Bridge, has been for many years a political and imaginative space that captures a diversity of local and national preoccupations. Keating’s announcement that planners have a “once-in-200-year opportunity to call a halt to the kind of encroachments we have seen in the past” is in fact another moment in the long history of disputation over the impact of the man-made environment on the natural landform in this area. This paper addresses the spaces of Sydney Harbour as represented in recent debates and in writing and film from previous decades. The argument suggests that the Harbour is a complex site of public and private enactment that is played out in a diverse range of cultural representations. In particular, the paper notes the work of Michel de Certeau on the mythic qualities of certain spaces in relation to the space of the Harbour. ‘The Greatest Harbour in the World’ argues that the Harbour, and the Bridge, fulfils a particular historical and cultural function that gives this space a set of meanings that are well beyond the typical parameters of urban development.

Computationally efficient methods for solving time-variable-order time-space fractional reaction-diffusion equation

Fractional differential equations are becoming more widely accepted as a powerful tool in modelling anomalous diffusion, which is exhibited by various materials and processes. Recently, researchers have suggested that rather than using constant order fractional operators, some processes are more accurately modelled using fractional orders that vary with time and/or space. In this paper we develop computationally efficient techniques for solving time-variable-order time-space fractional reaction-diffusion equations (tsfrde) using the finite difference scheme. We adopt the Coimbra variable order time fractional operator and variable order fractional Laplacian operator in space where both orders are functions of time. Because the fractional operator is nonlocal, it is challenging to efficiently deal with its long range dependence when using classical numerical techniques to solve such equations. The novelty of our method is that the numerical solution of the time-variable-order tsfrde is written in terms of a matrix function vector product at each time step. This product is approximated efficiently by the Lanczos method, which is a powerful iterative technique for approximating the action of a matrix function by projecting onto a Krylov subspace. Furthermore an adaptive preconditioner is constructed that dramatically reduces the size of the required Krylov subspaces and hence the overall computational cost. Numerical examples, including the variable-order fractional Fisher equation, are presented to demonstrate the accuracy and efficiency of the approach.