Fabrication and characterization of RF plasma polymerized thin films from 3,7-dimethyl-1,6-octadien-3-ol for electronic and biomaterial applications

Poly(linalool) thin films were fabricated using RF plasma polymerisation. All films were found to be smooth, defect-free surfaces with average roughness of 0.44 nm. The FTIR analysis of the polymer showed a notable reduction in –OH moiety and complete dissociation of C=C unsaturation compared to the monomer, and presence of a ketone band absent from the spectrum of the monomer. Poly(linalool) were characterised by chain branching and a large quantity of short polymer chains. Films were optically transparent, with refractive index and extinction coefficient of 1.55 and 0.001 (at 500 nm) respectively, indicating a potential application as an encapsulating (protective) coating for circuit boards. The optical band gap was calculated to be 2.82 eV, which is in the semiconducting energy gap region.

Fabrication and characterization of plasma polymer thin films from monoterpene alcohols for applications in organic electronics and biotechnology

After more than twenty years of basic and applied research, the use of nanotechnology in the design and manufacture of nanoscale materials is rapidly increasing, particularly in commercial applications that span from electronics across renewable energy areas, and biomedical devices. Novel polymers are attracting significant attention for they promise to provide a low−cost high−performance alternative to existing materials. Furthermore, these polymers have the potential to overcome limitations imposed by currently available materials thus enabling the development of new technologies and applications that are currently beyond our reach. This work focuses on the development of a range of new low−cost environmentally−friendly polymer materials for applications in areas of organic (flexible) electronics, optics, and biomaterials. The choice of the monomer reflects the environmentally−conscious focus of this project. Terpinen−4−ol is a major constituent of Australian grown Melaleuca alternifolia (tea tree) oil, attributed with the oil's antimicrobial and anti−inflammatory properties. Plasma polymerisation was chosen as a deposition technique for it requires minimal use of harmful chemicals and produces no hazardous by−products. Polymer thin films were fabricated under varied process conditions to attain materials with distinct physico−chemical, optoelectrical, biological and degradation characteristics. The resultant materials, named polyterpenol, were extensively characterised using a number of well−accepted and novel techniques, and their fundamental properties were defined. Polyterpenol films were demonstrated to be hydrocarbon rich, with variable content of oxygen moieties, primarily in the form of hydroxyl and carboxyl functionalities. The level of preservation of original monomer functionality was shown to be strongly dependent on the deposition energy, with higher applied power increasing the molecular fragmentation and substrate temperature. Polyterpenol water contact angle contact angle increased from 62.7° for the 10 W samples to 76.3° for the films deposited at 100 W. Polymers were determined to resist solubilisation by water, due to the extensive intermolecular and intramolecular hydrogen bonds present, and other solvents commonly employed in electronics and biomedical processing. Independent of deposition power, the surface topography of the polymers was shown to be smooth (Rq <0.5 nm), uniform and defect free. Hardness of polyterpenol coatings increased from 0.33 GPa for 10 W to 0.51 GPa for 100 W (at 500 μN load). Coatings deposited at higher input RF powers showed less mechanical deformation during nanoscratch testing, with no considerable damage, cracking or delamination observed. Independent of the substrate, the quality of film adhesion improved with RF power, suggesting these coatings are likely to be more stable and less susceptible to wear. Independent of fabrication conditions, polyterpenol thin films were optically transparent, with refractive index approximating that of glass. Refractive index increased slightly with deposition power, from 1.54 (10 W) to 1.56 (100 W) at 500 nm. The optical band gap values declined with increasing power, from 2.95 eV to 2.64 eV, placing the material within the range for semiconductors. Introduction of iodine impurity reduced the band gap of polyterpenol, from 2.8 eV to 1.64 eV, by extending the density of states more into the visible region of the electromagnetic spectrum. Doping decreased the transparency and increased the refractive index from 1.54 to 1.70 (at 500 nm). At optical frequencies, the real part of permittivity (k) was determined to be between 2.34 and 2.65, indicating a potential low-k material. These permittivity values were confirmed at microwave frequencies, where permittivity increased with input RF energy – from 2.32 to 2.53 (at 10 GHz ) and from 2.65 to 2.83 (at 20 GHz). At low frequencies, the dielectric constant was determined from current−voltage characteristics of Al−polyterpenol−Al devices. At frequencies below 100 kHz, the dielectric constant varied with RF power, from 3.86 to 4.42 at 1 kHz. For all samples, the resistivity was in order of 10⁸−10⁹ _m (at 6 V), confirming the insulating nature of polyterpenol material. In situ iodine doping was demonstrated to increase the conductivity of polyterpenol, from 5.05 × 10⁻⁸ S/cm to 1.20 × 10⁻⁶ S/cm (at 20 V). Exposed to ambient conditions over extended period of time, polyterpenol thin films were demonstrated to be optically, physically and chemically stable. The bulk of ageing occurred within first 150 h after deposition and was attributed to oxidation and volumetric relaxation. Thermal ageing studies indicated thermal stability increased for the films manufactured at higher RF powers, with degradation onset temperature associated with weight loss shifting from 150 ºC to 205 ºC for 10 W and 100 W polyterpenol, respectively. Annealing the films to 405 °C resulted in full dissociation of the polymer, with minimal residue. Given the outcomes of the fundamental characterisation, a number of potential applications for polyterpenol have been identified. Flexibility, tunable permittivity and loss tangent properties of polyterpenol suggest the material can be used as an insulating layer in plastic electronics. Implementation of polyterpenol as a surface modification of the gate insulator in pentacene-based Field Effect Transistor resulted in significant improvements, shifting the threshold voltage from + 20 V to –3 V, enhancing the effective mobility from 0.012 to 0.021 cm²/Vs, and improving the switching property of the device from 10⁷ to 10⁴. Polyterpenol was demonstrated to have a hole transport electron blocking property, with potential applications in many organic devices, such as organic light emitting diodes. Encapsulation of biomedical devices is also proposed, given that under favourable conditions, the original chemical and biological functionality of terpinen−4−ol molecule can be preserved. Films deposited at low RF power were shown to successfully prevent adhesion and retention of several important human pathogens, including P. aeruginosa, S. aureus, and S. epidermidis, whereas films deposited at higher RF power promoted bacterial cell adhesion and biofilm formation. Preliminary investigations into in vitro biocompatibility of polyterpenol demonstrated the coating to be non−toxic for several types of eukaryotic cells, including Balb/c mice macrophage and human monocyte type (HTP−1 non-adherent) cells. Applied to magnesium substrates, polyterpenol encapsulating layer significantly slowed down in vitro biodegradation of the metal, thus increasing the viability and growth of HTP−1 cells. Recently, applied to varied nanostructured titanium surfaces, polyterpenol thin films successfully reduced attachment, growth, and viability of P. aeruginosa and S. aureus.

Development and preliminary validation of the Drinking Expectancy Sexual Vulnerabilities Questionnaire (DESV-Q): A purpose-specific instrument for rape-perception research

Background Alcohol expectancies likely play a role in people’s perceptions of alcohol-involved sexual violence. However, no appropriate measure exists to examine this link comprehensively. Objective The aim of this research was to develop an alcohol expectancy measure which captures young adults’ beliefs about alcohol’s role in sexual aggression and victimization. Method Two cross-sectional samples of young Australian adults (18–25 years) were recruited for scale development (Phase 1) and scale validation (Phase 2). In Phase 1, participants (N = 201; 38.3% males) completed an online survey with an initial pool of alcohol expectancy items stated in terms of three targets (self, men, women) to identify the scale’s factor structure and most effective items. A revised alcohol expectancy scale was then administered online to 322 young adults (39.6% males) in Phase 2. To assess the predictive, convergent, and discriminant validity of the scale, participants also completed established measures of personality, social desirability, alcohol use, general and context-specific alcohol expectancies, and impulsiveness. Results Principal axis factoring (Phase 1) and confirmatory factor analysis (Phase 2) resulted in a target-equivalent five-factor structure for the final 66-item Drinking Expectancy Sexual Vulnerabilities Questionnaire (DESV-Q). The factors were labeled: - (1) Sexual Coercion - (2) Sexual Vulnerability - (3) Confidence - (4) Self-Centeredness - (5) Negative Cognitive and Behavioral Changes The measure demonstrated effective items, high internal consistency, and satisfactory predictive, convergent, and discriminant validity. Conclusions The DESV-Q is a purpose-specific instrument that could be used in future research to elucidate people’s attributions for alcohol-involved sexual aggression and victimization.

Decision trees for detection of activity intensity in youth with cerebral palsy

PURPOSE To develop and test decision tree (DT) models to classify physical activity (PA) intensity from accelerometer output and Gross Motor Function Classification System (GMFCS) classification level in ambulatory youth with cerebral palsy (CP); and 2) compare the classification accuracy of the new DT models to that achieved by previously published cut-points for youth with CP. METHODS Youth with CP (GMFCS Levels I - III) (N=51) completed seven activity trials with increasing PA intensity while wearing a portable metabolic system and ActiGraph GT3X accelerometers. DT models were used to identify vertical axis (VA) and vector magnitude (VM) count thresholds corresponding to sedentary (SED) (<1.5 METs), light PA (LPA) (>/=1.5 and <3 METs) and moderate-to-vigorous PA (MVPA) (>/=3 METs). Models were trained and cross-validated using the 'rpart' and 'caret' packages within R. RESULTS For the VA (VA_DT) and VM decision trees (VM_DT), a single threshold differentiated LPA from SED, while the threshold for differentiating MVPA from LPA decreased as the level of impairment increased. The average cross-validation accuracy for the VC_DT was 81.1%, 76.7%, and 82.9% for GMFCS levels I, II, and III, respectively. The corresponding cross-validation accuracy for the VM_DT was 80.5%, 75.6%, and 84.2%, respectively. Within each GMFCS level, the decision tree models achieved better PA intensity recognition than previously published cut-points. The accuracy differential was greatest among GMFCS level III participants, in whom the previously published cut-points misclassified 40% of the MVPA activity trials. CONCLUSION GMFCS-specific cut-points provide more accurate assessments of MVPA levels in youth with CP across the full spectrum of ambulatory ability.

Reliability and validity of objective measures of physical activity in youth with cerebral palsy who are ambulatory

BACKGROUND Physical therapy for youth with cerebral palsy (CP) who are ambulatory includes interventions to increase functional mobility and participation in physical activity (PA). Thus, reliable and valid measures are needed to document PA in youth with CP. OBJECTIVE The purpose of this study was to evaluate the inter-instrument reliability and concurrent validity of 3 accelerometer-based motion sensors with indirect calorimetry as the criterion for measuring PA intensity in youth with CP. METHODS Fifty-seven youth with CP (mean age=12.5 years, SD=3.3; 51% female; 49.1% with spastic hemiplegia) participated. Inclusion criteria were: aged 6 to 20 years, ambulatory, Gross Motor Function Classification System (GMFCS) levels I through III, able to follow directions, and able to complete the full PA protocol. Protocol activities included standardized activity trials with increasing PA intensity (resting, writing, household chores, active video games, and walking at 3 self-selected speeds), as measured by weight-relative oxygen uptake (in mL/kg/min). During each trial, participants wore bilateral accelerometers on the upper arms, waist/hip, and ankle and a portable indirect calorimeter. Intraclass coefficient correlations (ICCs) were calculated to evaluate inter-instrument reliability (left-to-right accelerometer placement). Spearman correlations were used to examine concurrent validity between accelerometer output (activity and step counts) and indirect calorimetry. Friedman analyses of variance with post hoc pair-wise analyses were conducted to examine the validity of accelerometers to discriminate PA intensity across activity trials. RESULTS All accelerometers exhibited excellent inter-instrument reliability (ICC=.94-.99) and good concurrent validity (rho=.70-.85). All accelerometers discriminated PA intensity across most activity trials. LIMITATIONS This PA protocol consisted of controlled activity trials. CONCLUSIONS Accelerometers provide valid and reliable measures of PA intensity among youth with CP.

Patterns of service utilisation within Australian hepatology clinics: High prevalence of advanced liver disease

Accepted Article Abstract Background: Liver diseases in Australia are estimated to affect 6 million people with a societal cost of $51 billion annually. Information about utilization of specialist hepatology care is critical in informing policy makers about the requirements for delivery of hepatology-related health care. Aims: This study examined etiology and severity of liver disease seen in a tertiary hospital hepatology clinic, as well as resource utilisation patterns. Methods: A longitudinal cohort study included consecutive patients booked in hepatology outpatient clinics during a 3 month period. Subsequent outpatient appointments for these patients over the following 12 months were then recorded. Results: During the initial 3 month period 1471 appointments were scheduled with a hepatologist, 1136 of which were attended. 21% of patients were “new cases”. Hepatitis B (HBV) was the most common disease etiology for new cases (37%). Advanced disease at presentation varied between etiology, with HBV (5%), Hepatitis C (HCV) (31%), non-alcoholic fatty liver disease (NAFLD) (46%) and alcoholic liver disease (ALD) (72%). Most patients (83%) attended multiple hepatology appointments, and a range of referrals patterns for procedures, investigations and other specialty assessments were observed. Conclusions: There is a high prevalence of HBV in new case referrals. Patients with HCV, NAFLD and ALD have a high prevalence of advanced liver disease at referral, requiring ongoing surveillance for development of decompensated liver disease and liver cancer. These findings that describe patterns of health service utilisation among patients with liver disease provide useful information for planning sustainable health service provision for this clinical population

Editorial of "International Journal of Critical Indigenous Studies, Volume 6, Number 1, 2013"

This edition of the International Journal of Critical Indigenous Studies marks the tenth since the journal’s launch in 2008. During that time, over forty articles and eleven book reviews have been published, which is testament to the continuing upward trajectory of Critical Indigenous Studies. Although there continues to be an increasing range of areas of Indigenous research to which a critical focus is brought to bear, a consistent issue for many of the journal’s contributors has been the delineation and application of Indigenous methods and methodologies in social research. The present edition is no exception, with two articles focussing on Indigenous-centred research. The first, by Krystal Summers, reflexively explores the author’s experiences as an undergraduate student undertaking Indigenous-centred research in Peru. As an Indigenous First Nations woman, Summers was mindful that her research practice was faithful to the ethics and protocols outlined in her original project proposal. Her subsequent ‘journey of critical reflexive understanding and storytelling’ supports the proposition of current literature in Indigenous research methodologies that a properly critical Indigenous ethnography will naturally enjoin with Indigenous epistemologies and methodologies.

Editorial of "International Journal of Critical Indigenous Studies Volume 6, Number 2, 2013"

The International Journal of Critical Indigenous Studies (IJCIS) now complements the recently launched National Indigenous Research and Knowledges Network (NIRAKN) in its efforts to build Indigenous research capacity. In this context the journal provides a platform for the research of Indigenous postgraduates, early- to mid-career researchers, and senior scholars. Indigenous scholars are therefore encouraged to submit their articles to future editions of the IJCIS, an ‘Excellence in Research for Australia’ (ERA) ranked journal.

Change to costs and lengths of stay in the emergency department and the Brisbane protocol: An observational study

- Objective To compare health service cost and length of stay between a traditional and an accelerated diagnostic approach to assess acute coronary syndromes (ACS) among patients who presented to the emergency department (ED) of a large tertiary hospital in Australia. - Design, setting and participants This historically controlled study analysed data collected from two independent patient cohorts presenting to the ED with potential ACS. The first cohort of 938 patients was recruited in 2008–2010, and these patients were assessed using the traditional diagnostic approach detailed in the national guideline. The second cohort of 921 patients was recruited in 2011–2013 and was assessed with the accelerated diagnostic approach named the Brisbane protocol. The Brisbane protocol applied early serial troponin testing for patients at 0 and 2 h after presentation to ED, in comparison with 0 and 6 h testing in traditional assessment process. The Brisbane protocol also defined a low-risk group of patients in whom no objective testing was performed. A decision tree model was used to compare the expected cost and length of stay in hospital between two approaches. Probabilistic sensitivity analysis was used to account for model uncertainty. - Results Compared with the traditional diagnostic approach, the Brisbane protocol was associated with reduced expected cost of $1229 (95% CI −$1266 to $5122) and reduced expected length of stay of 26 h (95% CI −14 to 136 h). The Brisbane protocol allowed physicians to discharge a higher proportion of low-risk and intermediate-risk patients from ED within 4 h (72% vs 51%). Results from sensitivity analysis suggested the Brisbane protocol had a high chance of being cost-saving and time-saving. - Conclusions This study provides some evidence of cost savings from a decision to adopt the Brisbane protocol. Benefits would arise for the hospital and for patients and their families.

The genetic associations of acute anterior uveitis and their overlap with the genetics of ankylosing spondylitis

Acute anterior uveitis (AAU) involves inflammation of the iris and ciliary body of the eye. It occurs both in isolation and as a complication of ankylosing spondylitis (AS). It is strongly associated with HLA-B*27, but previous studies have suggested that further genetic factors may confer additional risk. We sought to investigate this using the Illumina Exomechip microarray, to compare 1504 cases with AS and AAU, 1805 with AS but no AAU and 21 133 healthy controls. We also used a heterogeneity test to test the differences in effect size between AS with AAU and AS without AAU. In the analysis comparing AS+AAU+ cases versus controls, HLA-B*27 and HLA-A*02:01 were significantly associated with the presence of AAU (P<10−300 and P=6 × 10−8, respectively). Secondary independent association with PSORS1C3 (P=4.7 × 10−5) and TAP2 (P=1.1 × 10−5) were observed in the major histocompatibility complex. There was a new suggestive association with a low-frequency variant at zinc-finger protein 154 in the AS without AAU versus control analysis (zinc-finger protein 154 (ZNF154), P=2.2 × 10−6). Heterogeneity testing showed that rs30187 in ERAP1 has a larger effect on AAU compared with that in AS alone. These findings also suggest that variants in ERAP1 have a differential impact on the risk of AAU when compared with AS, and hence the genetic risk for AAU differs from AS.

Malaria rapid diagnostic test performance: Results of WHO product testing of malaria RDTs: Round 6 (2014-2015)

Overview This report, published in conjunction with a summary overview of results of rounds 1–6, is the sixth in a series of laboratory-based evaluations of rapid diagnostic tests (RDTs) for malaria. It provides a comparative measure of their performance in a standardized way to distinguish between well and poorly performing tests. It can be used by malaria control programmes and guide WHO procurement recommendations for these diagnostic tools. The evaluation reported here was a joint project of the WHO Global Malaria Programme, the Foundation for Innovative New Diagnostics (FIND) and the United States Centers for Disease Control and Prevention (CDC) within the WHO-FIND Malaria RDT Evaluation Programme. The project was financed by FIND through a grant from UNITAID.

How do Australian podiatrists manage patients with diabetes The Australian diabetic foot management survey

Background Diabetic foot complications are the leading cause of lower extremity amputation and diabetes-related hospitalisation in Australia. Studies demonstrate significant reductions in amputations and hospitalisation when health professionals implement best practice management. Whilst other nations have surveyed health professionals on specific diabetic foot management, to the best of the authors’ knowledge this appears not to have occurred in Australia. The primary aim of this study was to examine Australian podiatrists’ diabetic foot management compared with best practice recommendations by the Australian National Health Medical Research Council. Methods A 36-item Australian Diabetic Foot Management survey, employing seven-point Likert scales (0 = Never; 7 = Always) to measure multiple aspects of best practice diabetic foot management was developed. The survey was briefly tested for face and content validity. The survey was electronically distributed to Australian podiatrists via professional associations. Demographics including sex, years treating patients with diabetes, employment-sector and patient numbers were also collected. Chi-squared and Mann Whitney U tests were used to test differences between sub-groups. Results Three hundred and eleven podiatrists responded; 222 (71%) were female, 158 (51%) from the public sector and 11–15 years median experience. Participants reported treating a median of 21–30 diabetes patients each week, including 1–5 with foot ulcers. Overall, participants registered median scores of at least “very often” (>6) in their use of most items covering best practice diabetic foot management. Notable exceptions were: “never” (1 (1 – 3)) using total contact casting, “sometimes” (4 (2 – 5)) performing an ankle brachial index, “sometimes” (4 (1 – 6)) using University of Texas Wound Classification System, and “sometimes” (4 (3 – 6) referring to specialist multi-disciplinary foot teams. Public sector podiatrists reported higher use or access on all those items compared to private sector podiatrists (p < 0.01). Conclusions This study provides the first baseline information on Australian podiatrists’ adherence to best practice diabetic foot guidelines. It appears podiatrists manage large caseloads of people with diabetes and are generally implementing best practice guidelines recommendations with some notable exceptions. Further studies are required to identify barriers to implementing these recommendations to ensure all Australians with diabetes have access to best practice care to prevent amputations.

3D hierarchical rutile TiO2 and metal-free organic sensitizer producing dye-sensitized solar cells 8.6% conversion efficiency

Three-dimensional (3D) hierarchical nanoscale architectures comprised of building blocks, with specifically engineered morphologies, are expected to play important roles in the fabrication of 'next generation' microelectronic and optoelectronic devices due to their high surface-to-volume ratio as well as opto-electronic properties. Herein, a series of well-defined 3D hierarchical rutile TiO2 architectures (HRT) were successfully prepared using a facile hydrothermal method without any surfactant or template, simply by changing the concentration of hydrochloric acid used in the synthesis. The production of these materials provides, to the best of our knowledge, the first identified example of a ledgewise growth mechanism in a rutile TiO2 structure. Also for the first time, a Dye-sensitized Solar Cell (DSC) combining a HRT is reported in conjunction with a high-extinction-coefficient metal-free organic sensitizer (D149), achieving a conversion efficiency of 5.5%, which is superior to ones employing P25 (4.5%), comparable to state-of-the-art commercial transparent titania anatase paste (5.8%). Further to this, an overall conversion efficiency 8.6% was achieved when HRT was used as the light scattering layer, a considerable improvement over the commercial transparent/reflector titania anatase paste (7.6%), a significantly smaller gap in performance than has been seen previously.

Prevalence, codetection and seasonal distribution of upper airway viruses and bacteria in children with acute respiratory illnesses with cough as a symptom

Most studies exploring the role of upper airway viruses and bacteria in paediatric acute respiratory infections (ARI) focus on specific clinicaldiagnoses and/or do not account for virus–bacteria interactions. We aimed to describe the frequency and predictors of virus and bacteria codetection in children with ARI and cough, irrespective of clinical diagnosis. Bilateral nasal swabs, demographic, clinical and risk factor data were collected at enrollment in children aged <15 years presenting to an emergency department with an ARI and where cough was a symptom. Swabs were tested by polymerase chain reaction for 17 respiratory viruses and seven respiratory bacteria. Logistic regression was used to investigate associations between child characteristics and codetection of the organisms of interest. Between December 2011 and August 2014, swabs were collected from 817 (93.3%) of 876 enrolled children, median age 27.7 months (interquartile range13.9–60.3 months). Overall, 740 (90.6%) of 817 specimens were positive for any organism. Both viruses and bacteria were detected in 423 specimens (51.8%). Factors associated with codetection were age (adjusted odds ratio (aOR) for age <12 months = 4.9, 95% confidence interval (CI) 3.0, 7.9; age 12 to <24 months = 6.0, 95% CI 3.7, 9.8; age 24 to <60 months = 2.4, 95% CI 1.5, 3.9), male gender (aOR 1.46; 95% CI 1.1, 2.0), child care attendance (aOR 2.0; 95% CI 1.4, 2.8) and winter enrollment (aOR 2.0; 95% CI 1.3, 3.0). Haemophilus influenzae dominated the virus–bacteria pairs. Virus–H. influenzae interactions in ARI should be investigated further, especially as the contribution of nontypeable H. influenzae to acute and chronic respiratory diseases is being increasingly recognized.