Inelastic finite element analysis of composite beams on the basis of the plastic hinge approach

This paper emphasizes material nonlinear effects on composite beams with recourse to the plastic hinge method. Numerous combinations of steel and concrete sections form arbitrary composite sections. Secondly, the material properties of composite beams vary remarkably across its section from ductile steel to brittle concrete. Thirdly, concrete is weak in tension, so composite section changes are dependent on load distribution. To this end, the plastic zone approach is convenient for inelastic analysis of composite sections that can evaluate member resistance, including material nonlinearities, by routine numerical integration with respect to every fiber across the composite section. As a result, many researchers usually adopt the plastic zone approach for numerical inelastic analyses of composite structures. On the other hand, the plastic hinge method describes nonlinear material behaviour of an overall composite section integrally. Consequently, proper section properties for use in plastic hinge spring stiffness are required to represent the material behaviour across the arbitrary whole composite section. In view of numerical efficiency and convergence, the plastic hinge method is superior to the plastic zone method. Therefore, based on the plastic hinge approach, how to incorporate the material nonlinearities of the arbitrary composite section into the plastic hinge stiffness formulation becomes a prime objective of the present paper. The partial shear connection in this paper is by virtue of the effective flexural rigidity as AISC 1993 [American Institute of Steel Construction (AISC). Load and resistance factor design specifications. 2nd ed., Chicago; 1993]. Nonlinear behaviour of different kinds of composite beam is investigated in this paper, including two simply supported composite beams, a cantilever and a two span continuous composite beam.

Building adaptable agent-based models – application to the electricity distribution network

Agent-based modelling (ABM), like other modelling techniques, is used to answer specific questions from real world systems that could otherwise be expensive or impractical. Its recent gain in popularity can be attributed to some degree to its capacity to use information at a fine level of detail of the system, both geographically and temporally, and generate information at a higher level, where emerging patterns can be observed. This technique is data-intensive, as explicit data at a fine level of detail is used and it is computer-intensive as many interactions between agents, which can learn and have a goal, are required. With the growing availability of data and the increase in computer power, these concerns are however fading. Nonetheless, being able to update or extend the model as more information becomes available can become problematic, because of the tight coupling of the agents and their dependence on the data, especially when modelling very large systems. One large system to which ABM is currently applied is the electricity distribution where thousands of agents representing the network and the consumers’ behaviours are interacting with one another. A framework that aims at answering a range of questions regarding the potential evolution of the grid has been developed and is presented here. It uses agent-based modelling to represent the engineering infrastructure of the distribution network and has been built with flexibility and extensibility in mind. What distinguishes the method presented here from the usual ABMs is that this ABM has been developed in a compositional manner. This encompasses not only the software tool, which core is named MODAM (MODular Agent-based Model) but the model itself. Using such approach enables the model to be extended as more information becomes available or modified as the electricity system evolves, leading to an adaptable model. Two well-known modularity principles in the software engineering domain are information hiding and separation of concerns. These principles were used to develop the agent-based model on top of OSGi and Eclipse plugins which have good support for modularity. Information regarding the model entities was separated into a) assets which describe the entities’ physical characteristics, and b) agents which describe their behaviour according to their goal and previous learning experiences. This approach diverges from the traditional approach where both aspects are often conflated. It has many advantages in terms of reusability of one or the other aspect for different purposes as well as composability when building simulations. For example, the way an asset is used on a network can greatly vary while its physical characteristics are the same – this is the case for two identical battery systems which usage will vary depending on the purpose of their installation. While any battery can be described by its physical properties (e.g. capacity, lifetime, and depth of discharge), its behaviour will vary depending on who is using it and what their aim is. The model is populated using data describing both aspects (physical characteristics and behaviour) and can be updated as required depending on what simulation is to be run. For example, data can be used to describe the environment to which the agents respond to – e.g. weather for solar panels, or to describe the assets and their relation to one another – e.g. the network assets. Finally, when running a simulation, MODAM calls on its module manager that coordinates the different plugins, automates the creation of the assets and agents using factories, and schedules their execution which can be done sequentially or in parallel for faster execution. Building agent-based models in this way has proven fast when adding new complex behaviours, as well as new types of assets. Simulations have been run to understand the potential impact of changes on the network in terms of assets (e.g. installation of decentralised generators) or behaviours (e.g. response to different management aims). While this platform has been developed within the context of a project focussing on the electricity domain, the core of the software, MODAM, can be extended to other domains such as transport which is part of future work with the addition of electric vehicles.

Putting vital stains in context

While vital staining remains a cornerstone in the diagnosis of ocular disease and contact lens complications, there are many misconceptions regarding the properties of commonly used dyes by eye-care practitioners and what is and what is not corneal staining after instillation of sodium fluorescein. Similarly, the proper use and diagnostic utility of rose Bengal and lissamine green B, the other two ophthalmic dyes commonly used for assessing ocular complications, have similarly remained unclear. Due to the limitations of vital stains for definitive diagnosis, concomitant signs and symptoms in addition to a complete patient history are required. Over the past decade, there have been many reports of a type of corneal staining—often referred to as solution-induced corneal staining (SICS)—that is observed with the use of multipurpose solutions in combination with soft lenses, more specifically silicone hydrogel lenses. Some authors believe that SICS is a sign of lens/solution incompatibility; however, new research shows that SICS may be neither a measure of lens/solution biocompatibility nor ‘true’ corneal staining, as that observed in pathological situations. A large component of SICS may be a benign phenomenon, known as preservative-associated transient hyperfluorescence (PATH). There is a lack of correlated signs and/or symptoms with SICS/PATH. Several properties of SICS/PATH, such as appearance and duration, differentiate it from pathological corneal staining. This paper reviews the properties of vital stains, their use and limitations in assessment of the ocular surface, the aetiology of corneal staining, characteristics of SICS/PATH that differentiate it from pathological corneal staining and what the SICS/PATH phenomenon means for contact lens-wearing patients.

Selection et controle de modes de deplacement pour un robot mobile autonome en environnements naturels

Autonomous navigation and locomotion of a mobile robot in natural environments remain a rather open issue. Several functionalities are required to complete the usual perception/decision/action cycle. They can be divided in two main categories : navigation (perception and decision about the movement) and locomotion (movement execution). In order to be able to face the large range of possible situations in natural environments, it is essential to make use of various kinds of complementary functionalities, defining various navigation and locomotion modes. Indeed, a number of navigation and locomotion approaches have been proposed in the literature for the last years, but none can pretend being able to achieve autonomous navigation and locomotion in every situation. Thus, it seems relevant to endow an outdoor mobile robot with several complementary navigation and locomotion modes. Accordingly, the robot must also have means to select the most appropriate mode to apply. This thesis proposes the development of such a navigation/locomotion mode selection system, based on two types of data: an observation of the context to determine in what kind of situation the robot has to achieve its movement and an evaluation of the behavior of the current mode, made by monitors which influence the transitions towards other modes when the behavior of the current one is considered as non satisfying. Hence, this document introduces a probabilistic framework for the estimation of the mode to be applied, some navigation and locomotion modes used, a qualitative terrain representation method (based on the evaluation of a difficulty computed from the placement of the robot's structure on a digital elevation map), and monitors that check the behavior of the modes used (evaluation of rolling locomotion efficiency, robot's attitude and configuration watching. . .). Some experimental results obtained with those elements integrated on board two different outdoor robots are presented and discussed.

Physiological tolerance times while wearing explosive ordnance disposal protective clothing in simulated environmental extremes

Explosive ordnance disposal (EOD) technicians are required to wear protective clothing to protect themselves from the threat of overpressure, fragmentation, impact and heat. The engineering requirements to minimise these threats results in an extremely heavy and cumbersome clothing ensemble that increases the internal heat generation of the wearer, while the clothing’s thermal properties reduce heat dissipation. This study aimed to evaluate the heat strain encountered wearing EOD protective clothing in simulated environmental extremes across a range of differing work intensities. Eight healthy males [age 25±6 years (mean ± sd), height 180±7 cm, body mass 79±9 kg, V˙O2max 57±6 ml.kg−1.min−1] undertook nine trials while wearing an EOD9 suit (weighing 33.4 kg). The trials involved walking on a treadmill at 2.5, 4 and 5.5 km⋅h−1 at each of the following environmental conditions, 21, 30 and 37°C wet bulb globe temperature (WBGT) in a randomised controlled crossover design. The trials were ceased if the participants’ core temperature reached 39°C, if heart rate exceeded 90% of maximum, if walking time reached 60 minutes or due to fatigue/nausea. Tolerance times ranged from 10–60 minutes and were significantly reduced in the higher walking speeds and environmental conditions. In a total of 15 trials (21%) participants completed 60 minutes of walking; however, this was predominantly at the slower walking speeds in the 21°C WBGT environment. Of the remaining 57 trials, 50 were ceased, due to attainment of 90% maximal heart rate. These near maximal heart rates resulted in moderate-high levels of physiological strain in all trials, despite core temperature only reaching 39°C in one of the 72 trials.

Weekly cisplatin concurrently with radiotherapy in head and neck squamous cell cancer : a retrospective analysis of a tertiary institute experience

Radiotherapy combined with three weekly 100 mg/m2 of cisplatin is the accepted standard of care in head and neck squamous cell carcinoma. However, this regimen is associated with severe toxicities with devastating effects on patients. Alternative protocols like weekly 40 mg/m2 have been used in an attempt to reduce toxicities. The main objective of the present study is to identify the dose intensities and toxicities of weekly cisplatin in patients treated in a tertiary centre over a 12 month period. Included patients had squamous cell carcinoma arising in the oral cavity, oropharynx, larynx, or hypopharynx. Patients were excluded if they had nasopharyngeal squamous cell carcinoma, distant metastasis or if they had prior treatment for head and neck cancer excluding neck dissection. During the study period, 52 patients met the inclusion criteria and their data were retrospectively obtained from the patients' database of St James hospital, Dublin. The median age of the study cohort was 54 years (range 33-73). Of the patients, 40 (76.9 %) were male and 12 (20.1 %) were female. The primary tumour sites were as follows: oral cavity and oropharynx in 38 (73 %), larynx in 10 (19 %), and hypopharynx in 4 (8 %). In total, 33 (63.5 %) patients had stage IV disease, while 19 (36.5 %) had stage III disease. Treatment was definitive in 35 (67 %) patients and adjuvant in 17 (35 %). Full-dose radiotherapy was achieved in 50 (96 %) patients. Only 22 (42.3 %) patients completed the intended six cycles of chemotherapy. Cumulative dose of 200 mg/m2 or more was reached in 37 (71 %) patients. The acute adverse effects included grades 3 and 4 mucositis, which occurred in 22 (43.3 %) and 6 patients (12 %), respectively. Grade 3 and 4 neutropenia occurred in six (11.5 %) and three (5.7 %) patients, respectively. The only other haematological toxicity was grade 3 anaemia in 20 (38.4 %) patients. There was no grade 3 or 4 renal toxicity among the study cohort, although grade 2 was observed in six (11.5 %) patients. Death occurred in one patient due to neutropenic septicaemia. In conclusion, weekly cisplatin is associated with moderate to severe toxicities and might lead to suboptimal chemotherapy delivery. More prospective clinical studies are required to determine the optimal chemoradiation regimen in head and neck squamous cell carcinoma.

Last word : opportunity to educate

The article discusses the importance that learning to live sustainably in order to provide healthy and fulfilling lives for future generations. The things that need to be done differently and the innovative partnerships that are required are highlighted.

Can we text you? A qualitative exploration of young unemployed job-seekers’ attitudes to receiving resilience-building SMS messages

A significant minority of young job-seekers remain unemployed for many months, and are at risk of developing depression. Both empirical studies and theoretical models suggest that cognitive, behavioural and social isolation factors interact to increase this risk. Thus, interventions that reduce or prevent depression in young unemployed job-seekers by boosting their resilience are required. Mobile phones may be an effective medium to deliver resilience-boosting support to young unemployed people by using SMS messages to interrupt the feedback loop of depression and social isolation. Three focus groups were conducted to explore young unemployed job-seekers’ attitudes to receiving and requesting regular SMS messages that would help them to feel supported and motivated while job-seeking. Participants reacted favourably to this proposal, and thought that it would be useful to continue to receive and request SMS messages for a few months after commencing employment as well.

Genuine community engagement in remote dryland regions : natural resource management in Lake Eyre Basin

Remote dryland regions are characterised by sparse populations and socially marginalised voices which pose particular challenges to natural resource management. This paper considers the issue of how to achieve community engagement in regions with these characteristics. In doing so, the paper contributes to an expanding international research agenda focusing on the distinct characteristics of arid and semi-arid regions under the heading of 'dryland syndrome'. The paper draws on government liaison officer and local community perspectives of successful engagement in the case-study region of Lake Eyre Basin, Australia. The results demonstrate that widely recognised characteristics of successful engagement are required but insufficient for genuine engagement in remote dryland regions. In addition to building trust through community ownership, being inclusive, effective communication, and adequate resources, genuine community engagement in drylands also requires respecting the extreme conditions and extraordinary variability of these areas. Residents of dryland regions seek genuine engagement yet engage opportunistically when seasons are conducive and when tangible outcomes are visible. © 2011 The Authors. Geographical Research © 2011 Institute of Australian Geographers.

Different in vitro activation methods for latent transforming growth factors (TGF)–β : considerable exogenous factors to promote higher mesenchymal-origin cell proliferation in a bioprocessing platform

Regenerative medicine includes two efficient techniques, namely tissue-engineering and cell-based therapy in order to repair tissue damage efficiently. Most importantly, huge numbers of autologous cells are required to deal these practices. Nevertheless, primary cells, from autologous tissue, grow very slowly while culturing in vitro; moreover, they lose their natural characteristics over prolonged culturing period. Transforming growth factors-beta (TGF-β) is a ubiquitous protein found biologically in its latent form, which prevents it from eliciting a response until conversion to its active form. In active form, TGF-β acts as a proliferative agent in many cell lines of mesenchymal origin in vitro. This article reviews on some of the important activation methods-physiochemical, enzyme-mediated, non-specific protein interaction mediated, and drug-induced- of TGF-β, which may be established as exogenous factors to be used in culturing medium to obtain extensive proliferation of primary cells.

Journalism Across Cultures : An Introduction

In today's global digital world, journalists are required to be cognizant of ethical and cultural issues beyond usual national boundaries. Drawing on global examples, this text examines international journalism through the authors' wide variety of cultural, educational, teaching and learning backgrounds, including their professional and practical experiences. While existing books tend to be more focused on specific regions or specific aspects of journalism, this book addresses in a comprehensive way journalism across cultures from a truly global (and holistic) perspective. It analyzes media systems in Africa, Latin America, the Arab world and the Middle East, China, as well as North America and Western Europe. This text is truly interdisciplinary in theoretical and practical approaches because it draws on other fields such as media and cultural studies, anthropology, sociology, linguistics, as well as politics and international relations. It will provide an introduction to cross-cultural journalism and equip students with the skills and understanding they need today.

Measurement of the first neutron diffraction peak of D2O flowing in a 2 mm diameter aluminium tube as a function of temperature

A pilot experiment was performed using the WOMBAT powder diffraction instrument at ANSTO in which the first neutron diffraction peak (Q0) was measured for D2O flowing in a 2 mm internal diameter aluminium tube. Measurements of Q0 were made at -9, 4.3, 6.9, 12, 18.2 and 21.5 °C. The D2O was circulated using a siphon with water in the lower reservoir returned to the upper reservoir using a small pump. This enabled stable flow to be maintained for several hours. For example, if the pump flow increased slightly, the upper reservoir level rose, increasing the siphon flow until it matched the return flow. A neutron wavelength of 2.4 Å was used and data integrated over 60 minutes for each temperature. A jet of nitrogen from a liquid N2 Dewar was directed over the aluminium tube to vary water temperature. After collection of the data, the d spacing of the aluminium peaks was used to calculate the temperature of the aluminium within the neutron beam and therefore was considered to be an accurate measure of water temperature within the beam. Sigmaplot version 12.3 was used to fit a Weibull five parameter peak fit to the first neutron diffraction peak. The values of Q0 obtained in this experiment showed an increase with temperature consistent with data in the literature [1] but were consistently higher than published values for bulk D20. For example at 21.5 °C we obtained a value of 2.008 Å-1 for Q0 compared to a literature value of 1.988 Å-1 for bulk D2O at 20 °C, a difference of 1%. Further experiments are required to see if this difference is real or artifactual.

The first x-ray diffraction peak of water as a function of temperature in the range 4 – 63 °C

X-ray diffraction structure functions for water flowing in a 1.5 mm diameter siphon in the temperature range 4 – 63 °C were obtained using a 20 keV beam at the Australian Synchrotron. These functions were compared with structure functions obtained at the Advanced Light Source for a 0.5 mm thick sample of water in the temperature range 1 – 77 °C irradiated with an 11 keV beam. The two sets of structure functions are similar, but there are subtle differences in the shape and relative position of the two functions suggesting a possible differences between the structure of bulk and siphon water. In addition, the first structural peak (Q0) for water in a siphon, showed evidence of a step-wise increase in Q0 with increasing temperature rather than a smoothly varying increase. More experiments are required to investigate this apparent difference.

Transfer pricing and multinational financial institutions : the case for replacing arm’s length price with a unitary approach

The international tax system, designed a century ago, has not kept pace with the modern multinational entity rendering it ineffective in taxing many modern businesses according to economic activity. One of those modern multinational entities is the multinational financial institution (MNFI). The recent global financial crisis provides a particularly relevant and significant example of the failure of the current system on a global scale. The modern MNFI is increasingly undertaking more globalised and complex trading operations. A primary reason for the globalisation of financial institutions is that they typically ‘follow-the-customer’ into jurisdictions where international capital and international investors are required. The International Monetary Fund (IMF) recently reported that from 1995-2009, foreign bank presence in developing countries grew by 122 per cent. The same study indicates that foreign banks have a 20 per cent market share in OECD countries and 50 per cent in emerging markets and developing countries. Hence, most significant is that fact that MNFIs are increasingly undertaking an intermediary role in developing economies where they are financing core business activities such as mining and tourism. IMF analysis also suggests that in the future, foreign bank expansion will be greatest in emerging economies. The difficulties for developing countries in applying current international tax rules, especially the current traditional transfer pricing regime, are particularly acute in relation to MNFIs, which are the biggest users of tax havens and offshore finance. This paper investigates whether a unitary taxation approach which reflects economic reality would more easily and effectively ensure that the profits of MNFIs are taxed in the jurisdictions which give rise to those profits. It has previously been argued that the uniqueness of MNFIs results in a failure of the current system to accurately allocate profits and that unitary tax as an alternative could provide a sounder allocation model for international tax purposes. This paper goes a step further, and examines the practicalities of the implementation of unitary taxation for MNFIs in terms of the key components of such a regime, along with their their implications. This paper adopts a two-step approach in considering the implications of unitary taxation as a means of improved corporate tax coordination which requires international acceptance and agreement. First, the definitional issues of the unitary MNFI are examined and second, an appropriate allocation formula for this sector is investigated. To achieve this, the paper asks first, how the financial sector should be defined for the purposes of unitary taxation and what should constitute a unitary business for that sector and second, what is the ‘best practice’ model of an allocation formula for the purposes of the apportionment of the profits of the unitary business of a financial institution.

Carbon nanotube composite sensor for structural health monitoring of bridge structures

Bridges are important infrastructures of all nations and are required for transportation of goods as well as human. A catastrophic failure can result in loss of lives and enormous financial hardship to the nation. Although various kinds of sensors are now available to monitor the health of the structures due to corrosion, they do not provide permanent and long term measurements. This paper investigates the fabrication of Carbon Nanotube (CNT) based composite sensors for corrosion detection of structures. Multi-wall CNT (MWCNT)/Nafion composite sensors were fabricated to evaluate their electrical properties for corrosion detection. The test specimens were subjected to real life corrosion experimental tests and the results confirm that the electrical resistance of the sensor electrode was dramatically changed due to corrosion.