CFD simulations of flow and heat transfer through the porous interface of a metal foam heat exchanger

This paper offers numerical modelling of a waste heat recovery system. A thin layer of metal foam is attached to a cold plate to absorb heat from hot gases leaving the system. The heat transferred from the exhaust gas is then transferred to a cold liquid flowing in a secondary loop. Two different foam PPI (Pores Per Inch) values are examined over a range of fluid velocities. Numerical results are then compared to both experimental data and theoretical results available in the literature. Challenges in getting the simulation results to match those of the experiments are addressed and discussed in detail. In particular, interface boundary conditions specified between a porous layer and a fluid layer are investigated. While physically one expects much lower fluid velocity in the pores compared to that of free flow, capturing this sharp gradient at the interface can add to the difficulties of numerical simulation. The existing models in the literature are modified by considering the pressure gradient inside and outside the foam. Comparisons against the numerical modelling are presented. Finally, based on experimentally-validated numerical results, thermo-hydraulic performance of foam heat exchangers as waste heat recovery units is discussed with the main goal of reducing the excess pressure drop and maximising the amount of heat that can be recovered from the hot gas stream.

A matrix converter based Inductive Power Transfer system

Typical Inductive Power Transfer (IPT) systems employ two power conversion stages to generate a high frequency current from low frequency utility supply. This paper proposes a matrix converter based IPT system that facilitates the generation of high frequency current through a single power conversion stage. The proposed matrix converter topology transforms a 3-phase low frequency voltage system to a high frequency single phase voltage which in turn powers a series compensated IPT system. A comprehensive mathematical model is developed to investigate the behavior of the proposed IPT topology. Theoretical results are presented in comparison to simulations, which are performed in Matlab/ Simulink, to demonstrate the applicability of the proposed concept and the validity of the developed model.

Contrast transfer function correction applied to cryo-electron tomography and sub-tomogram averaging

Cryo-electron tomography together with averaging of sub-tomograms containing identical particles can reveal the structure of proteins or protein complexes in their native environment. The resolution of this technique is limited by the contrast transfer function (CTF) of the microscope. The CTF is not routinely corrected in cryo-electron tomography because of difficulties including CTF detection, due to the low signal to noise ratio, and CTF correction, since images are characterised by a spatially variant CTF. Here we simulate the effects of the CTF on the resolution of the final reconstruction, before and after CTF correction, and consider the effect of errors and approximations in defocus determination. We show that errors in defocus determination are well tolerated when correcting a series of tomograms collected at a range of defocus values. We apply methods for determining the CTF parameters in low signal to noise images of tilted specimens, for monitoring defocus changes using observed magnification changes, and for correcting the CTF prior to reconstruction. Using bacteriophage PRDI as a test sample, we demonstrate that this approach gives an improvement in the structure obtained by sub-tomogram averaging from cryo-electron tomograms.

Blood transfer devices for malaria rapid diagnostic tests : evaluation of accuracy, safety and ease of use

Background: Malaria rapid diagnostic tests (RDTs) are increasingly used by remote health personnel with minimal training in laboratory techniques. RDTs must, therefore, be as simple, safe and reliable as possible. Transfer of blood from the patient to the RDT is critical to safety and accuracy, and poses a significant challenge to many users. Blood transfer devices were evaluated for accuracy and precision of volume transferred, safety and ease of use, to identify the most appropriate devices for use with RDTs in routine clinical care. Methods: Five devices, a loop, straw-pipette, calibrated pipette, glass capillary tube, and a new inverted cup device, were evaluated in Nigeria, the Philippines and Uganda. The 227 participating health workers used each device to transfer blood from a simulated finger-prick site to filter paper. For each transfer, the number of attempts required to collect and deposit blood and any spilling of blood during transfer were recorded. Perceptions of ease of use and safety of each device were recorded for each participant. Blood volume transferred was calculated from the area of blood spots deposited on filter paper. Results: The overall mean volumes transferred by devices differed significantly from the target volume of 5 microliters (p < 0.001). The inverted cup (4.6 microliters) most closely approximated the target volume. The glass capillary was excluded from volume analysis as the estimation method used is not compatible with this device. The calibrated pipette accounted for the largest proportion of blood exposures (23/225, 10%); exposures ranged from 2% to 6% for the other four devices. The inverted cup was considered easiest to use in blood collection (206/ 226, 91%); the straw-pipette and calibrated pipette were rated lowest (143/225 [64%] and 135/225 [60%] respectively). Overall, the inverted cup was the most preferred device (72%, 163/227), followed by the loop (61%, 138/227). Conclusions: The performance of blood transfer devices varied in this evaluation of accuracy, blood safety, ease of use, and user preference. The inverted cup design achieved the highest overall performance, while the loop also performed well. These findings have relevance for any point-of-care diagnostics that require blood sampling.

Cascaded multilevel converter based bidirectional inductive power transfer (BIPT) system

A typical low power IPT system employs an H-Bridge converter with a simple control strategy to generate a high frequency current from DC power supply. This paper proposes a cascaded multilevel converter for bidirectional IPT (BIPT) systems, which is suitable for low to medium power applications as well as for situations such as PV cells where several individual DC sources are to be utilized. A novel modulation strategy is proposed for the multilevel converter with the aim of minimizing switching losses. Series - Series (SS) compensation circuit is adopted for the IPT system and a mathematical model is presented to minimize the coil losses of the system under varying output power. Theoretical results presented in comparison to the simulations to demonstrate the applicability of the proposed concept and the validity of the developed model. The experimental results show the feasibility of the proposed phase shift modulation.

The pollution release and transfer register system in the U.S. and Japan : an analysis of productivity

This study analyzes Total Factor Productivity (TFP), which includes all categories of productivity. Our measure investigates productivity in the context of the provision and dissemination of environmental information policies. We investigated data on the emission of toxic chemical substances for the U.S. and Japanese manufacturing firms, including 386 firms for the period 1999-2007 and 466 firms for the period 2001-2008. The results show that productivity improved in all nine industrial sectors and that pollution levels were high in the U.S. and Japan from 2001 to 2007. In particular, the electronics industry improved rapidly after 2002 in both countries, which may be attributed to the enforcement of RoHS and the REACH directive in Europe. As a result of these stringent policies on toxic chemical emissions, the U.S. and Japanese firms, many of which export to the European market, have strong incentives to reduce their toxic chemical emissions.

Knowledge Transfer in Transnational Programmes : Opportunities and Challenges for the Pacific Region

The globalised world: The current higher education community The last decade has seen rapid changes in the landscape of higher education (HE) throughout the world, largely as a product of globalisation. A major effect has been to propel the interconnectedness between nations and people across the globe (Scholte, 2005). The use of information and communication technology (ICT) has diminished the distance between countries. The world’s economies are becoming more integrated and interrelated through neoliberal economic policies, free trade agreements and open access of goods and services beyond national borders, policies promulgated by organisations such as the World Trade Organization and The World Bank (Marginson & Ordorika, 2011; Mok, 2011). As a consequence, universities are operating at global, national and local levels simultaneously. In the Pacific region, new universities are emerging. For example, Fiji now has one regional and two national universities; Samoa has a national university and Solomon Islands has an institute of higher education. These new players add to regional competition as they open opportunities for global partnerships and transnational programmes. Thus, participating at these multiple levels is inevitable, and no university is immune to these changes (Marginson, Kaur & Sawir, 2011a). Universities are now part of the global HE community that cannot be confined within a nation’s borders. Transitional HE programmes are perhaps one of the most evident demonstrations of the interconnectedness of universities across countries in this global era.

Examining the critical interplay of knowledge acquisition and integration capabilities in service innovation-based competitive advantage in project oriented service firms

While past knowledge-based approaches to service innovation have emphasized the role of knowledge integration in the delivery of customer-focused solutions, these approaches do not adequately address the complexities inherent in knowledge acquisition and integration in project-oriented firms. Adopting a dynamic capability framework and building on knowledge-based approaches to innovation, the current study examines how the interplay of learning capabilities and knowledge integration capability impacts service innovation and sustained competitive advantage. This two-stage multi-sample study finds that entrepreneurial project-oriented service firms in their quest for competitive advantage through greater innovation invest in knowledge acquisition and integration capabilities. Implications for theory and practice are discussed and directions for future research provided.

Cyclododecane as support material for clean and facile transfer of large-area few-layer graphene

The transfer of chemical vapor deposited graphene is a crucial process, which can affect the quality of the transferred films and compromise their application in devices. Finding a robust and intrinsically clean material capable of easing the transfer of graphene without interfering with its properties remains a challenge. We here propose the use of an organic compound, cyclododecane, as a transfer material. This material can be easily spin coated on graphene and assist the transfer, leaving no residues and requiring no further removal processes. The effectiveness of this transfer method for few-layer graphene on a large area was evaluated and confirmed by microscopy, Raman spectroscopy, x-ray photoemission spectroscopy, and four-point probe measurements. Schottky-barrier solar cells with few-layer graphene were fabricated on silicon wafers by using the cyclododecane transfer method and outperformed reference cells made by standard methods.

Knowledge management challenges in small-and medium-sized enterprises

Background & Research Focus Managing knowledge for innovation and organisational benefit has been extensively investigated in studies of large firms (Smith, Collins & Clark, 2005; Zucker, et al., 2007) and to a large extent there is limited research into studies of small- and medium- sized enterprises (SMEs). There are some investigations in knowledge management research on SMEs, but what remains to be seen in particular is the question of where are the potential challenges for managing knowledge more effectively within these firms? Effective knowledge management (KM) processes and systems lead to improved performance in pursuing distinct capabilities that contribute to firm-level innovation (Nassim 2009; Zucker et al. 2007; Verona and Ravasi 2003). Managing internal and external knowledge in a way that links it closely to the innovation process can assist the creation and implementation of new products and services. KM is particularly important in knowledge intensive firms where the knowledge requirements are highly specialized, diverse and often emergent. However, to a large extent the KM processes of small firms that are often the source of new knowledge and an important element of the value networks of larger companies have not been closely studied. To address this gap which is of increasing importance with the growing number of small firms, we need to further investigate knowledge management processes and the ways that firms find, capture, apply and integrate knowledge from multiple sources for their innovation process. This study builds on the previous literature and applies existing frameworks and takes the process and activity view of knowledge management as a starting point of departure (see among others Kraaijenbrink, Wijnhoven & Groen, 2007; Enberg, Lindkvist, & Tell, 2006; Lu, Wang & Mao, 2007). In this paper, it is attempted to develop a better understanding of the challenges of knowledge management within the innovation process in small knowledge-oriented firms. The paper aims to explore knowledge management processes and practices in firms that are engaged in the new product/service development programs. Consistent with the exploratory character of the study, the research question is: How is knowledge integrated, sourced and recombined from internal and external sources for innovation and new product development? Research Method The research took an exploratory case study approach and developed a theoretical framework to investigate the knowledge situation of knowledge-intensive firms. Equipped with the conceptual foundation, the research adopted a multiple case study method investigating four diverse Australian knowledge-intensive firms from IT, biotechnology, nanotechnology and biochemistry industries. The multiple case study method allowed us to document in some depth the knowledge management experience of the theses firms. Case study data were collected through a review of company published data and semi-structured interviews with managers using an interview guide to ensure uniform coverage of the research themes. This interview guide was developed following development of the framework and a review of the methodologies and issues covered by similar studies in other countries and used some questions common to these studies. It was framed to gather data around knowledge management activity within the business, focusing on the identification, acquisition and utilisation of knowledge, but collecting a range of information about subject as well. The focus of the case studies was on the use of external and internal knowledge to support their knowledge intensive products and services. Key Findings Firstly a conceptual and strategic knowledge management framework has been developed. The knowledge determinants are related to the nature of knowledge, organisational context, and mechanism of the linkages between internal and external knowledge. Overall, a number of key observations derived from this study, which demonstrated the challenges of managing knowledge and how important KM is as a management tool for innovation process in knowledge-oriented firms. To summarise, findings suggest that knowledge management process in these firms is very much project focused and not embedded within the overall organisational routines and mainly based on ad hoc and informal processes. Our findings highlighted lack of formal knowledge management process within our sampled firms. This point to the need for more specialised capabilities in knowledge management for these firms. We observed a need for an effective knowledge transfer support system which is required to facilitate knowledge sharing and particularly capturing and transferring tacit knowledge from one team members to another. In sum, our findings indicate that building effective and adaptive IT systems to manage and share knowledge in the firm is one of the biggest challenges for these small firms. Also, there is little explicit strategy in small knowledge-intensive firms that is targeted at systematic KM either at the strategic or operational level. Therefore, a strategic approach to managing knowledge for innovation as well as leadership and management are essential to achieving effective KM. In particular, research findings demonstrate that gathering tacit knowledge, internal and external to the organization, and applying processes to ensure the availability of knowledge for innovation teams, drives down the risks and cost of innovation. KM activities and tools, such as KM systems, environmental scanning, benchmarking, intranets, firm-wide databases and communities of practice to acquire knowledge and to make it accessible, were elements of KM. Practical Implications The case study method that used in this study provides practical insight into the knowledge management process within Australian knowledge-intensive firms. It also provides useful lessons which can be used by other firms in managing the knowledge more effectively in the innovation process. The findings would be helpful for small firms that may be searching for a practical method for managing and integrating their specialised knowledge. Using the results of this exploratory study and to address the challenges of knowledge management, this study proposes five practices that are discussed in the paper for managing knowledge more efficiently to improve innovation: (1) Knowledge-based firms must be strategic in knowledge management processes for innovation, (2) Leadership and management should encourage various practices for knowledge management, (3) Capturing and sharing tacit knowledge is critical and should be managed, (4)Team knowledge integration practices should be developed, (5) Knowledge management and integration through communication networks, and technology systems should be encouraged and strengthen. In sum, the main managerial contribution of the paper is the recognition of knowledge determinants and processes, and their effects on the effective knowledge management within firm. This may serve as a useful benchmark in the strategic planning of the firm as it utilises new and specialised knowledge.

Kumarina and bidders voting in transfer schemes

Transfer schemes are an alternative means of acquiring control of a company to making a takeover bid under the provisions in Ch 6 of the Corporations Act 2001 (Cth). The recent decision Re Kumarina Resources Ltd [2013] FCA 549 overturned long-standing practice in relation to a certain type of transfer scheme. If followed, the decision would allow a “bidder” to vote at scheme meetings where the scheme consideration for the acquisition of the target shares are shares in another company, and the scheme results in a merger. But the bidder is not allowed to vote where the scheme consideration is cash. The article points out the difficulties arising from this decision and argues that it should not be followed. In providing a “no objection” statement, the Australian Securities and Investments Commission (ASIC) has created uncertainty as to the approach it will take towards the bidders being allowed to vote at scheme meetings where the scheme consideration for the acquisition of target shares are shares in another company. The article also points out that in providing the no objection statement in Kumarina, ASIC appears to have ignored breaches of s 606(1) of the Corporations Act. There is a pressing need for ASIC to clarify its position and, in particular, whether or not it will provide a no objection statement in respect of future transfer schemes where a bidder (or its parent company) votes at the scheme meeting.

The establishment of an ISO compliant cancer biobank for Jordan and its neighboring countries through knowledge transfer and training

Research studies aimed at advancing cancer prevention, diagnosis, and treatment depend on a number of key resources, including a ready supply of high-quality annotated biospecimens from diverse ethnic populations that can be used to test new drugs, assess the validity of prognostic biomarkers, and develop tailor-made therapies. In November 2011, KHCCBIO was established at the King Hussein Cancer Center (KHCC) with the support of Seventh Framework Programme (FP7) funding from the European Union (khccbio.khcc.jo). KHCCBIO was developed for the purpose of achieving an ISO accredited cancer biobank through the collection, processing, and preservation of high-quality, clinically annotated biospecimens from consenting cancer patients, making it the first cancer biobank of its kind in Jordan. The establishment of a state-of-the-art, standardized biospecimen repository of matched normal and lung tumor tissue, in addition to blood components such as serum, plasma, and white blood cells, was achieved through the support and experience of its European partners, Trinity College Dublin, Biostor Ireland, and accelopment AG. To date, KHCCBIO along with its partners, have worked closely in establishing an ISO Quality Management System (QMS) under which the biobank will operate. A Quality Policy Manual, Validation, and Training plan have been developed in addition to the development of standard operating procedures (SOPs) for consenting policies on ethical issues, data privacy, confidentiality, and biobanking bylaws. SOPs have also been drafted according to best international practices and implemented for the donation, procurement, processing, testing, preservation, storage, and distribution of tissues and blood samples from lung cancer patients, which will form the basis for the procurement of other cancer types. KHCCBIO will be the first ISO accredited cancer biobank from a diverse ethnic Middle Eastern and North African population. It will provide a unique and valuable resource of high-quality human biospecimens and anonymized clinicopathological data to the cancer research communities world-wide.