Heavy vehicle suspensions : testing and analysis

Transport regulators consider that, with respect to pavement damage, heavy vehicles (HVs) are the riskiest vehicles on the road network. That HV suspension design contributes to road and bridge damage has been recognised for some decades. This thesis deals with some aspects of HV suspension characteristics, particularly (but not exclusively) air suspensions. This is in the areas of developing low-cost in-service heavy vehicle (HV) suspension testing, the effects of larger-than-industry-standard longitudinal air lines and the characteristics of on-board mass (OBM) systems for HVs. All these areas, whilst seemingly disparate, seek to inform the management of HVs, reduce of their impact on the network asset and/or provide a measurement mechanism for worn HV suspensions. A number of project management groups at the State and National level in Australia have been, and will be, presented with the results of the project that resulted in this thesis. This should serve to inform their activities applicable to this research. A number of HVs were tested for various characteristics. These tests were used to form a number of conclusions about HV suspension behaviours. Wheel forces from road test data were analysed. A “novel roughness” measure was developed and applied to the road test data to determine dynamic load sharing, amongst other research outcomes. Further, it was proposed that this approach could inform future development of pavement models incorporating roughness and peak wheel forces. Left/right variations in wheel forces and wheel force variations for different speeds were also presented. This led on to some conclusions regarding suspension and wheel force frequencies, their transmission to the pavement and repetitive wheel loads in the spatial domain. An improved method of determining dynamic load sharing was developed and presented. It used the correlation coefficient between two elements of a HV to determine dynamic load sharing. This was validated against a mature dynamic loadsharing metric, the dynamic load sharing coefficient (de Pont, 1997). This was the first time that the technique of measuring correlation between elements on a HV has been used for a test case vs. a control case for two different sized air lines. That dynamic load sharing was improved at the air springs was shown for the test case of the large longitudinal air lines. The statistically significant improvement in dynamic load sharing at the air springs from larger longitudinal air lines varied from approximately 30 percent to 80 percent. Dynamic load sharing at the wheels was improved only for low air line flow events for the test case of larger longitudinal air lines. Statistically significant improvements to some suspension metrics across the range of test speeds and “novel roughness” values were evident from the use of larger longitudinal air lines, but these were not uniform. Of note were improvements to suspension metrics involving peak dynamic forces ranging from below the error margin to approximately 24 percent. Abstract models of HV suspensions were developed from the results of some of the tests. Those models were used to propose further development of, and future directions of research into, further gains in HV dynamic load sharing. This was from alterations to currently available damping characteristics combined with implementation of large longitudinal air lines. In-service testing of HV suspensions was found to be possible within a documented range from below the error margin to an error of approximately 16 percent. These results were in comparison with either the manufacturer’s certified data or test results replicating the Australian standard for “road-friendly” HV suspensions, Vehicle Standards Bulletin 11. OBM accuracy testing and development of tamper evidence from OBM data were detailed for over 2000 individual data points across twelve test and control OBM systems from eight suppliers installed on eleven HVs. The results indicated that 95 percent of contemporary OBM systems available in Australia are accurate to +/- 500 kg. The total variation in OBM linearity, after three outliers in the data were removed, was 0.5 percent. A tamper indicator and other OBM metrics that could be used by jurisdictions to determine tamper events were developed and documented. That OBM systems could be used as one vector for in-service testing of HV suspensions was one of a number of synergies between the seemingly disparate streams of this project.

Examining psychosocial influences on speeding in Australian and Chinese contexts : a social learning approach

Speeding remains a significant contributing factor to road trauma internationally, despite increasingly sophisticated speed management strategies being adopted around the world. Increases in travel speed are associated with increases in crash risk and crash severity. As speed choice is a voluntary behaviour, driver perceptions are important to our understanding of speeding and, importantly, to designing effective behavioural countermeasures. The four studies conducted in this program of research represent a comprehensive approach to examining psychosocial influences on driving speeds in two countries that are at very different levels of road safety development: Australia and China. Akers’ social learning theory (SLT) was selected as the theoretical framework underpinning this research and guided the development of key research hypotheses. This theory was chosen because of its ability to encompass psychological, sociological, and criminological perspectives in understanding behaviour, each of which has relevance to speeding. A mixed-method design was used to explore the personal, social, and legal influences on speeding among car drivers in Queensland (Australia) and Beijing (China). Study 1 was a qualitative exploration, via focus group interviews, of speeding among 67 car drivers recruited from south east Queensland. Participants were assigned to groups based on their age and gender, and additionally, according to whether they self-identified as speeding excessively or rarely. This study aimed to elicit information about how drivers conceptualise speeding as well as the social and legal influences on driving speeds. The findings revealed a wide variety of reasons and circumstances that appear to be used as personal justifications for exceeding speed limits. Driver perceptions of speeding as personally and socially acceptable, as well as safe and necessary were common. Perceptions of an absence of danger associated with faster driving speeds were evident, particularly with respect to driving alone. An important distinction between the speed-based groups related to the attention given to the driving task. Rare speeders expressed strong beliefs about the need to be mindful of safety (self and others) while excessive speeders referred to the driving task as automatic, an absent-minded endeavour, and to speeding as a necessity in order to remain alert and reduce boredom. For many drivers in this study, compliance with speed limits was expressed as discretionary rather than mandatory. Social factors, such as peer and parental influence were widely discussed in Study 1 and perceptions of widespread community acceptance of speeding were noted. In some instances, the perception that ‘everybody speeds’ appeared to act as one rationale for the need to raise speed limits. Self-presentation, or wanting to project a positive image of self was noted, particularly with respect to concealing speeding infringements from others to protect one’s image as a trustworthy and safe driver. The influence of legal factors was also evident. Legal sanctions do not appear to influence all drivers to the same extent. For instance, fear of apprehension appeared to play a role in reducing speeding for many, although previous experiences of detection and legal sanctions seemed to have had limited influence on reducing speeding among some drivers. Disregard for sanctions (e.g., driving while suspended), fraudulent demerit point use, and other strategies to avoid detection and punishment were widely and openly discussed. In Study 2, 833 drivers were recruited from roadside service stations in metropolitan and regional locations in Queensland. A quantitative research strategy assessed the relative contribution of personal, social, and legal factors to recent and future self-reported speeding (i.e., frequency of speeding and intentions to speed in the future). Multivariate analyses examining a range of factors drawn from SLT revealed that factors including self-identity (i.e., identifying as someone who speeds), favourable definitions (attitudes) towards speeding, personal experiences of avoiding detection and punishment for speeding, and perceptions of family and friends as accepting of speeding were all significantly associated with greater self-reported speeding. Study 3 was an exploratory, qualitative investigation of psychosocial factors associated with speeding among 35 Chinese drivers who were recruited from the membership of a motoring organisation and a university in Beijing. Six focus groups were conducted to explore similar issues to those examined in Study 1. The findings of Study 3 revealed many similarities with respect to the themes that arose in Australia. For example, there were similarities regarding personal justifications for speeding, such as the perception that posted limits are unreasonably low, the belief that individual drivers are able to determine safe travel speeds according to personal comfort with driving fast, and the belief that drivers possess adequate skills to control a vehicle at high speed. Strategies to avoid detection and punishment were also noted, though they appeared more widespread in China and also appeared, in some cases, to involve the use of a third party, a topic that was not reported by Australian drivers. Additionally, higher perceived enforcement tolerance thresholds were discussed by Chinese participants. Overall, the findings indicated perceptions of a high degree of community acceptance of speeding and a perceived lack of risk associated with speeds that were well above posted speed limits. Study 4 extended the exploratory research phase in China with a quantitative investigation involving 299 car drivers recruited from car washes in Beijing. Results revealed a relatively inexperienced sample with less than 5 years driving experience, on average. One third of participants perceived that the certainty of penalties when apprehended was low and a similar proportion of Chinese participants reported having previously avoided legal penalties when apprehended for speeding. Approximately half of the sample reported that legal penalties for speeding were ‘minimally to not at all’ severe. Multivariate analyses revealed that past experiences of avoiding detection and punishment for speeding, as well as favourable attitudes towards speeding, and perceptions of strong community acceptance of speeding were most strongly associated with greater self-reported speeding in the Chinese sample. Overall, the results of this research make several important theoretical contributions to the road safety literature. Akers’ social learning theory was found to be robust across cultural contexts with respect to speeding; similar amounts of variance were explained in self-reported speeding in the quantitative studies conducted in Australia and China. Historically, SLT was devised as a theory of deviance and posits that deviance and conformity are learned in the same way, with the balance of influence stemming from the ways in which behaviour is rewarded and punished (Akers, 1998). This perspective suggests that those who speed and those who do not are influenced by the same mechanisms. The inclusion of drivers from both ends of the ‘speeding spectrum’ in Study 1 provided an opportunity to examine the wider utility of SLT across the full range of the behaviour. One may question the use of a theory of deviance to investigate speeding, a behaviour that could, arguably, be described as socially acceptable and prevalent. However, SLT seemed particularly relevant to investigating speeding because of its inclusion of association, imitation, and reinforcement variables which reflect the breadth of factors already found to be potentially influential on driving speeds. In addition, driving is a learned behaviour requiring observation, guidance, and practice. Thus, the reinforcement and imitation concepts are particularly relevant to this behaviour. Finally, current speed management practices are largely enforcement-based and rely on the principles of behavioural reinforcement captured within the reinforcement component of SLT. Thus, the application of SLT to a behaviour such as speeding offers promise in advancing our understanding of the factors that influence speeding, as well as extending our knowledge of the application of SLT. Moreover, SLT could act as a valuable theoretical framework with which to examine other illegal driving behaviours that may not necessarily be seen as deviant by the community (e.g., mobile phone use while driving). This research also made unique contributions to advancing our understanding of the key components and the overall structure of Akers’ social learning theory. The broader SLT literature is lacking in terms of a thorough structural understanding of the component parts of the theory. For instance, debate exists regarding the relevance of, and necessity for including broader social influences in the model as captured by differential association. In the current research, two alternative SLT models were specified and tested in order to better understand the nature and extent of the influence of differential association on behaviour. Importantly, the results indicated that differential association was able to make a unique contribution to explaining self-reported speeding, thereby negating the call to exclude it from the model. The results also demonstrated that imitation was a discrete theoretical concept that should also be retained in the model. The results suggest a need to further explore and specify mechanisms of social influence in the SLT model. In addition, a novel approach was used to operationalise SLT variables by including concepts drawn from contemporary social psychological and deterrence-based research to enhance and extend the way that SLT variables have traditionally been examined. Differential reinforcement was conceptualised according to behavioural reinforcement principles (i.e., positive and negative reinforcement and punishment) and incorporated concepts of affective beliefs, anticipated regret, and deterrence-related concepts. Although implicit in descriptions of SLT, little research has, to date, made use of the broad range of reinforcement principles to understand the factors that encourage or inhibit behaviour. This approach has particular significance to road user behaviours in general because of the deterrence-based nature of many road safety countermeasures. The concept of self-identity was also included in the model and was found to be consistent with the definitions component of SLT. A final theoretical contribution was the specification and testing of a full measurement model prior to model testing using structural equation modelling. This process is recommended in order to reduce measurement error by providing an examination of the psychometric properties of the data prior to full model testing. Despite calls for such work for a number of decades, the current work appears to be the only example of a full measurement model of SLT. There were also a number of important practical implications that emerged from this program of research. Firstly, perceptions regarding speed enforcement tolerance thresholds were highlighted as a salient influence on driving speeds in both countries. The issue of enforcement tolerance levels generated considerable discussion among drivers in both countries, with Australian drivers reporting lower perceived tolerance levels than Chinese drivers. It was clear that many drivers used the concept of an enforcement tolerance in determining their driving speed, primarily with the desire to drive faster than the posted speed limit, yet remaining within a speed range that would preclude apprehension by police. The quantitative results from Studies 2 and 4 added support to these qualitative findings. Together, the findings supported previous research and suggested that a travel speed may not be seen as illegal until that speed reaches a level over the prescribed enforcement tolerance threshold. In other words, the enforcement tolerance appears to act as a ‘de facto’ speed limit, replacing the posted limit in the minds of some drivers. The findings from the two studies conducted in China (Studies 2 and 4) further highlighted the link between perceived enforcement tolerances and a ‘de facto’ speed limit. Drivers openly discussed driving at speeds that were well above posted speed limits and some participants noted their preference for driving at speeds close to ‘50% above’ the posted limit. This preference appeared to be shaped by the perception that the same penalty would be imposed if apprehended, irrespective of what speed they travelling (at least up to 50% above the limit). Further research is required to determine whether the perceptions of Chinese drivers are mainly influenced by the Law of the People’s Republic of China or by operational practices. Together, the findings from both studies in China indicate that there may be scope to refine enforcement tolerance levels, as has happened in other jurisdictions internationally over time, in order to reduce speeding. Any attempts to do so would likely be assisted by the provision of information about the legitimacy and purpose of speed limits as well as risk factors associated with speeding because these issues were raised by Chinese participants in the qualitative research phase. Another important practical implication of this research for speed management in China is the way in which penalties are determined. Chinese drivers described perceptions of unfairness and a lack of transparency in the enforcement system because they were unsure of the penalty that they would receive if apprehended. Steps to enhance the perceived certainty and consistency of the system to promote a more equitable approach to detection and punishment would appear to be welcomed by the general driving public and would be more consistent with the intended theoretical (deterrence) basis that underpins the current speed enforcement approach. The use of mandatory, fixed penalties may assist in this regard. In many countries, speeding attracts penalties that are dependent on the severity of the offence. In China, there may be safety benefits gained from the introduction of a similar graduated scale of speeding penalties and fixed penalties might also help to address the issue of uncertainty about penalties and related perceptions of unfairness. Such advancements would be in keeping with the principles of best practice for speed management as identified by the World Health Organisation. Another practical implication relating to legal penalties, and applicable to both cultural contexts, relates to the issues of detection and punishment avoidance. These two concepts appeared to strongly influence speeding in the current samples. In Australia, detection avoidance strategies reported by participants generally involved activities that are not illegal (e.g., site learning and remaining watchful for police vehicles). The results from China were similar, although a greater range of strategies were reported. The most common strategy reported in both countries for avoiding detection when speeding was site learning, or familiarisation with speed camera locations. However, a range of illegal practices were also described by Chinese drivers (e.g., tampering with or removing vehicle registration plates so as to render the vehicle unidentifiable on camera and use of in-vehicle radar detectors). With regard to avoiding punishment when apprehended, a range of strategies were reported by drivers from both countries, although a greater range of strategies were reported by Chinese drivers. As the results of the current research indicated that detection avoidance was strongly associated with greater self-reported speeding in both samples, efforts to reduce avoidance opportunities are strongly recommended. The practice of randomly scheduling speed camera locations, as is current practice in Queensland, offers one way to minimise site learning. The findings of this research indicated that this practice should continue. However, they also indicated that additional strategies are needed to reduce opportunities to evade detection. The use of point-to-point speed detection (also known as sectio

Predicting effects of monotony on driver’s vigilance

Monotony has been identified as a contributing factor to road crashes. Drivers’ ability to react to unpredictable events deteriorates when exposed to highly predictable and uneventful driving tasks, such as driving on Australian rural roads, many of which are monotonous by nature. Highway design in particular attempts to reduce the driver’s task to a merely lane-keeping one. Such a task provides little stimulation and is monotonous, thus affecting the driver’s attention which is no longer directed towards the road. Inattention contributes to crashes, especially for professional drivers. Monotony has been studied mainly from the endogenous perspective (for instance through sleep deprivation) without taking into account the influence of the task itself (repetitiveness) or the surrounding environment. The aim and novelty of this thesis is to develop a methodology (mathematical framework) able to predict driver lapses of vigilance under monotonous environments in real time, using endogenous and exogenous data collected from the driver, the vehicle and the environment. Existing approaches have tended to neglect the specificity of task monotony, leaving the question of the existence of a “monotonous state” unanswered. Furthermore the issue of detecting vigilance decrement before it occurs (predictions) has not been investigated in the literature, let alone in real time. A multidisciplinary approach is necessary to explain how vigilance evolves in monotonous conditions. Such an approach needs to draw on psychology, physiology, road safety, computer science and mathematics. The systemic approach proposed in this study is unique with its predictive dimension and allows us to define, in real time, the impacts of monotony on the driver’s ability to drive. Such methodology is based on mathematical models integrating data available in vehicles to the vigilance state of the driver during a monotonous driving task in various environments. The model integrates different data measuring driver’s endogenous and exogenous factors (related to the driver, the vehicle and the surrounding environment). Electroencephalography (EEG) is used to measure driver vigilance since it has been shown to be the most reliable and real time methodology to assess vigilance level. There are a variety of mathematical models suitable to provide a framework for predictions however, to find the most accurate model, a collection of mathematical models were trained in this thesis and the most reliable was found. The methodology developed in this research is first applied to a theoretically sound measure of sustained attention called Sustained Attention Response to Task (SART) as adapted by Michael (2010), Michael and Meuter (2006, 2007). This experiment induced impairments due to monotony during a vigilance task. Analyses performed in this thesis confirm and extend findings from Michael (2010) that monotony leads to an important vigilance impairment independent of fatigue. This thesis is also the first to show that monotony changes the dynamics of vigilance evolution and tends to create a “monotonous state” characterised by reduced vigilance. Personality traits such as being a low sensation seeker can mitigate this vigilance decrement. It is also evident that lapses in vigilance can be predicted accurately with Bayesian modelling and Neural Networks. This framework was then applied to the driving task by designing a simulated monotonous driving task. The design of such task requires multidisciplinary knowledge and involved psychologist Rebecca Michael. Monotony was varied through both the road design and the road environment variables. This experiment demonstrated that road monotony can lead to driving impairment. Particularly monotonous road scenery was shown to have the most impact compared to monotonous road design. Next, this study identified a variety of surrogate measures that are correlated with vigilance levels obtained from the EEG. Such vigilance states can be predicted with these surrogate measures. This means that vigilance decrement can be detected in a car without the use of an EEG device. Amongst the different mathematical models tested in this thesis, only Neural Networks predicted the vigilance levels accurately. The results of both these experiments provide valuable information about the methodology to predict vigilance decrement. Such an issue is quite complex and requires modelling that can adapt to highly inter-individual differences. Only Neural Networks proved accurate in both studies, suggesting that these models are the most likely to be accurate when used on real roads or for further research on vigilance modelling. This research provides a better understanding of the driving task under monotonous conditions. Results demonstrate that mathematical modelling can be used to determine the driver’s vigilance state when driving using surrogate measures identified during this study. This research has opened up avenues for future research and could result in the development of an in-vehicle device predicting driver vigilance decrement. Such a device could contribute to a reduction in crashes and therefore improve road safety.

Derivation of motor vehicle tailpipe particle emission factors suitable for modelling urban fleet emissions and air quality assessments

Background, aim, and scope Urban motor vehicle fleets are a major source of particulate matter pollution, especially of ultrafine particles (diameters < 0.1 µm), and exposure to particulate matter has known serious health effects. A considerable body of literature is available on vehicle particle emission factors derived using a wide range of different measurement methods for different particle sizes, conducted in different parts of the world. Therefore the choice as to which are the most suitable particle emission factors to use in transport modelling and health impact assessments presented as a very difficult task. The aim of this study was to derive a comprehensive set of tailpipe particle emission factors for different vehicle and road type combinations, covering the full size range of particles emitted, which are suitable for modelling urban fleet emissions. Materials and methods A large body of data available in the international literature on particle emission factors for motor vehicles derived from measurement studies was compiled and subjected to advanced statistical analysis, to determine the most suitable emission factors to use in modelling urban fleet emissions. Results This analysis resulted in the development of five statistical models which explained 86%, 93%, 87%, 65% and 47% of the variation in published emission factors for particle number, particle volume, PM1, PM2.5 and PM10 respectively. A sixth model for total particle mass was proposed but no significant explanatory variables were identified in the analysis. From the outputs of these statistical models, the most suitable particle emission factors were selected. This selection was based on examination of the statistical robustness of the statistical model outputs, including consideration of conservative average particle emission factors with the lowest standard errors, narrowest 95% confidence intervals and largest sample sizes, and the explanatory model variables, which were Vehicle Type (all particle metrics), Instrumentation (particle number and PM2.5), Road Type (PM10) and Size Range Measured and Speed Limit on the Road (particle volume). Discussion A multiplicity of factors need to be considered in determining emission factors that are suitable for modelling motor vehicle emissions, and this study derived a set of average emission factors suitable for quantifying motor vehicle tailpipe particle emissions in developed countries. Conclusions The comprehensive set of tailpipe particle emission factors presented in this study for different vehicle and road type combinations enable the full size range of particles generated by fleets to be quantified, including ultrafine particles (measured in terms of particle number). These emission factors have particular application for regions which may have a lack of funding to undertake measurements, or insufficient measurement data upon which to derive emission factors for their region. Recommendations and perspectives In urban areas motor vehicles continue to be a major source of particulate matter pollution and of ultrafine particles. It is critical that in order to manage this major pollution source methods are available to quantify the full size range of particles emitted for traffic modelling and health impact assessments.

Ions in motor vehicle exhaust and their dispersion near busy roads

Measurements in the exhaust plume of a petrol-driven motor car showed that molecular cluster ions of both signs were present in approximately equal amounts. The emission rate increased sharply with engine speed while the charge symmetry remained unchanged. Measurements at the kerbside of nine motorways and five city roads showed that the mean total cluster ion concentration near city roads (603 cm-3) was about one-half of that near motorways (1211 cm-3) and about twice as high as that in the urban background (269 cm-3). Both positive and negative ion concentrations near a motorway showed a significant linear increase with traffic density (R2=0.3 at p<0.05) and correlated well with each other in real time (R2=0.87 at p<0.01). Heavy duty diesel vehicles comprised the main source of ions near busy roads. Measurements were conducted as a function of downwind distance from two motorways carrying around 120-150 vehicles per minute. Total traffic-related cluster ion concentrations decreased rapidly with distance, falling by one-half from the closest approach of 2m to 5m of the kerb. Measured concentrations decreased to background at about 15m from the kerb when the wind speed was 1.3 m s-1, this distance being greater at higher wind speed. The number and net charge concentrations of aerosol particles were also measured. Unlike particles that were carried downwind to distances of a few hundred metres, cluster ions emitted by motor vehicles were not present at more than a few tens of metres from the road.

Powered two wheelers in a changing world : challenges and opportunities

Powered two wheelers (PTWs) come in diverse forms and are used for a range of purposes in very different parts of the world. In many parts of the world, the forms and uses of PTWs are changing, influenced by social, economic and demographic changes. Most of the challenges associated with PTWs relate to safety, while the majority of the opportunities relate to mobility. The challenges for improving safety relate to the PTW user, other road users, the road environment, the vehicle, data and research, and socio-political dimensions. The relative importance of particular challenges varies between developed and developing countries, and among developing countries according to whether PTWs are largely used for recreation or for transport. PTWs present a range of psychological, transport, economic and environmental opportunities to individuals and societies. The fun and excitement of riding PTWs is a major motivator for their purchase and use for recreational purposes, both off-road and on-road. The transport and economic advantages to the individual also need to be considered. At a societal level, research has examined the potential for increasing PTW volumes to reduce fossil fuel use and traffic congestion in busy cities. The future of PTWs may differ greatly between countries and environmental and technological changes are leading to an evolution in the form of PTWs to encompass new modes of personal transportation.

Older adults’ safety perceptions of driving situations: Towards a new driving self-regulation scale

The term ‘driving self-restriction’ is used in the road safety literature to describe the behaviour of some older drivers. It includes the notion that older drivers will avoid driving in specific, usually self-identified situations, such as those in which safety is compromised. We sought to identify the situations that older drivers report avoiding; and, to determine the adequacy of a key measure of such behaviour. A sample of 75 drivers aged 65 years and older completed Baldock et al.’s modification of the Driving Habits Questionnaire avoidance items (Baldock et al., 2006), the Driving Behaviour Questionnaire, and open-ended items that elicited written descriptions of the most and least safe driving situation. Consistent with previous results, we found a relatively low level of driving self-restriction and infrequent episodes of aggressive violations. However, when combined with the situation descriptions, these data suggest that Driving Habits Questionnaire did not cover all of the situations that older drivers might choose avoid. We suggest that a new avoidance scale is needed and we present a new item pool that may be used for this purpose.

Textbook portrayal of grieving stereotypes fails to cohere : a review

JANIS Balodis's Engine appears to have an educative purpose. Following the tragic death of her brother Stevie in a car crash, Natasha and her family struggle to cope with the devastation this sudden trauma has dealt them. Overlooked by her grieving parents, Natasha expresses her emotions by skipping school, self-harming and, as Engine unfolds, trying to enlist her Grumpop to help her finish rebuilding the car that could have saved Stevie's life by eliminating his need to catch a ride with a car full of friends. The symbolic action that drives Engine - rebuilding the car to rebuild Natasha and Grumpop's lives in the wake of trauma and guilt - is full of potential. It gives the design team, particularly designer Justin Nardella and composer Matt Hill, a strong premise to construct the garage that transforms into a home, a school, a church, a part, and the road on which the accident took place as the play unfolds.

Backseat Drivers

Script for non verbal performance work for young audiences. Three productions by the Queensland Theatre Company 2000-2002. (QTC/QPAC) Out of the Box Festival of Early Childhood 2000. Queensland Arts Council Tours 2000, 2001, 2002. Seoul Arts Centre 2000 Selected by ASSITEJ as a representative script for Australia Set entirely in the backseat of a car, with the road behind appearing on a rear-projection screen, Backseat Driver is the story of two very different children battling the fingerdrumming, motor-humming boredom of a long car trip. Using non-verbal performance, video projection and the music of Cliff Richard, Elvis Presley and the Shadows, Backseat Drivers is a comedy for anyone who has ever asked the question ”are we there yet?”. Exploring the power of creative play, Backseat Driver has enjoyed three productions, including a season for Korean audiences at the Seoul Arts Centre in 2001.

Backseat drivers

Script for non verbal performance work for young audiences. Three productions by the Queensland Theatre Company 2000-2002. ----- ----- ----- (QTC/QPAC) Out of the Box Festival of Early Childhood 2000. Queensland Arts Council Tours 2000, 2001, 2002. Seoul Arts Centre 2000 ----- ----- ----- Selected by ASSITEJ as a representative script for Australia ----- ----- ----- Set entirely in the backseat of a car, with the road behind appearing on a rear-projection screen, Backseat Driver is the story of two very different children battling the fingerdrumming, motor-humming boredom of a long car trip. Using non-verbal performance, video projection and the music of Cliff Richard, Elvis Presley and the Shadows, Backseat Drivers is a comedy for anyone who has ever asked the question ”are we there yet?”. Exploring the power of creative play, Backseat Driver has enjoyed three productions, including a season for Korean audiences at the Seoul Arts Centre in 2001.

Social influences on drivers in China

China is one of Asia’s many rapidly-motorising nations and recent increases in private-vehicle ownership have been coupled with an escalation in novice drivers. Several pieces of road safety legislation have been introduced in recent decades in China. While managing the legal aspects of road use is important, social influences on driver behaviour may offer alternative avenues to alter behaviour, particularly in a culture where such factors carry high importance. This paper reports qualitative research with Beijing drivers to investigate social influence factors that have, to date, received little attention in the literature. Findings indicated that family members, friends, and driving instructors appear influential on driver behaviour and that some newly licensed drivers seek additional assistance to facilitate the transition from learning to drive in a controlled environment to driving on the road in complex conditions. Strategies to avoid detection and penalties for inappropriate road use were described, many of which involved the use of a third person. These findings indicate potential barriers to implementing effective traffic enforcement and highlight the importance of understanding culturally-specific social factors relating to driver behaviour.

Real-time evaluation of driver’s alertness on highways

Suburbanisation has been internationally a major phenomenon in the last decades. Suburb-to-suburb routes are nowadays the most widespread road journeys; and this resulted in an increment of distances travelled, particularly on faster suburban highways. The design of highways tends to over-simplify the driving task and this can result in decreased alertness. Driving behaviour is consequently impaired and drivers are then more likely to be involved in road crashes. This is particularly dangerous on highways where the speed limit is high. While effective countermeasures to this decrement in alertness do not currently exist, the development of in-vehicle sensors opens avenues for monitoring driving behaviour in real-time. The aim of this study is to evaluate in real-time the level of alertness of the driver through surrogate measures that can be collected from in-vehicle sensors. Slow EEG activity is used as a reference to evaluate driver's alertness. Data are collected in a driving simulator instrumented with an eye tracking system, a heart rate monitor and an electrodermal activity device (N=25 participants). Four different types of highways (driving scenario of 40 minutes each) are implemented through the variation of the road design (amount of curves and hills) and the roadside environment (amount of buildings and traffic). We show with Neural Networks that reduced alertness can be detected in real-time with an accuracy of 92% using lane positioning, steering wheel movement, head rotation, blink frequency, heart rate variability and skin conductance level. Such results show that it is possible to assess driver's alertness with surrogate measures. Such methodology could be used to warn drivers of their alertness level through the development of an in-vehicle device monitoring in real-time drivers' behaviour on highways, and therefore it could result in improved road safety.

Illegal street racing and associated (hooning) behaviours

In an Australian context, the term hooning refers to risky driving behaviours such as illegal street racing and speed trials, as well as behaviours that involve unnecessary noise and smoke, which include burn outs, donuts, fish tails, drifting and other skids. Hooning receives considerable negative media attention in Australia, and since the 1990s all Australian jurisdictions have implemented vehicle impoundment programs to deal with the problem. However, there is limited objective evidence of the road safety risk associated with hooning behaviours. Attempts to estimate the risk associated with hooning are limited by official data collection and storage practices, and the willingness of drivers to admit to their illegal behaviour in the event of a crash. International evidence suggests that illegal street racing is associated with only a small proportion of fatal crashes; however, hooning in an Australian context encompasses a broader group of driving behaviours than illegal street racing alone, and it is possible that the road safety risks will differ with these behaviours. There is evidence from North American jurisdictions that vehicle impoundment programs are effective for managing drink driving offenders, and drivers who continue to drive while disqualified or suspended both during and post-impoundment. However, these programs used impoundment periods of 30 – 180 days (depending on the number of previous offences). In Queensland the penalty for a first hooning offence is 48 hours, while the vehicle can be impounded for up to 3 months for a second offence, or permanently for a third or subsequent offence within three years. Thus, it remains unclear whether similar effects will be seen for hooning offenders in Australia, as no evaluations of vehicle impoundment programs for hooning have been published. To address these research needs, this program of research consisted of three complementary studies designed to: (1) investigate the road safety implications of hooning behaviours in terms of the risks associated with the specific behaviours, and the drivers who engage in these behaviours; and (2) assess the effectiveness of current approaches to dealing with the problem; in order to (3) inform policy and practice in the area of hooning behaviour. Study 1 involved qualitative (N = 22) and quantitative (N = 290) research with drivers who admitted engaging in hooning behaviours on Queensland roads. Study 2 involved a systematic profile of a large sample of drivers (N = 834) detected and punished for a hooning offence in Queensland, and a comparison of their driving and crash histories with a randomly sampled group of Queensland drivers with the same gender and age distribution. Study 3 examined the post-impoundment driving behaviour of hooning offenders (N = 610) to examine the effects of vehicle impoundment on driving behaviour. The theoretical framework used to guide the research incorporated expanded deterrence theory, social learning theory, and driver thrill-seeking perspectives. This framework was used to explore factors contributing to hooning behaviours, and interpret the results of the aspects of the research designed to explore the effectiveness of vehicle impoundment as a countermeasure for hooning. Variables from each of the perspectives were related to hooning measures, highlighting the complexity of the behaviour. This research found that the road safety risk of hooning behaviours appears low, as only a small proportion of the hooning offences in Study 2 resulted in a crash. However, Study 1 found that hooning-related crashes are less likely to be reported than general crashes, particularly when they do not involve an injury, and that higher frequencies of hooning behaviours are associated with hooning-related crash involvement. Further, approximately one fifth of drivers in Study 1 reported being involved in a hooning-related crash in the previous three years, which is comparable to general crash involvement among the general population of drivers in Queensland. Given that hooning-related crashes represented only a sub-set of crash involvement for this sample, this suggests that there are risks associated with hooning behaviour that are not apparent in official data sources. Further, the main evidence of risk associated with the behaviour appears to relate to the hooning driver, as Study 2 found that these drivers are likely to engage in other risky driving behaviours (particularly speeding and driving vehicles with defects or illegal modifications), and have significantly more traffic infringements, licence sanctions and crashes than drivers of a similar (i.e., young) age. Self-report data from the Study 1 samples indicated that Queensland’s vehicle impoundment and forfeiture laws are perceived as severe, and that many drivers have reduced their hooning behaviour to avoid detection. However, it appears that it is more common for drivers to have simply changed the location of their hooning behaviour to avoid detection. When the post-impoundment driving behaviour of the sample of hooning offenders was compared to their pre-impoundment behaviour to examine the effectiveness of vehicle impoundment in Study 3, it was found that there was a small but significant reduction in hooning offences, and also for other traffic infringements generally. As Study 3 was observational, it was not possible to control for extraneous variables, and is, therefore, possible that some of this reduction was due to other factors, such as a reduction in driving exposure, the effects of changes to Queensland’s Graduated Driver Licensing scheme that were implemented during the study period and affected many drivers in the offender sample due to their age, or the extension of vehicle impoundment to other types of offences in Queensland during the post-impoundment period. However, there was a protective effect observed, in that hooning offenders did not show the increase in traffic infringements in the post period that occurred within the comparison sample. This suggests that there may be some effect of vehicle impoundment on the driving behaviour of hooning offenders, and that this effect is not limited to their hooning driving behaviour. To be more confident in these results, it is necessary to measure driving exposure during the post periods to control for issues such as offenders being denied access to vehicles. While it was not the primary aim of this program of research to compare the utility of different theoretical perspectives, the findings of the research have a number of theoretical implications. For example, it was found that only some of the deterrence variables were related to hooning behaviours, and sometimes in the opposite direction to predictions. Further, social learning theory variables had stronger associations with hooning. These results suggest that a purely legal approach to understanding hooning behaviours, and designing and implementing countermeasures designed to reduce these behaviours, are unlikely to be successful. This research also had implications for policy and practice, and a number of recommendations were made throughout the thesis to improve the quality of relevant data collection practices. Some of these changes have already occurred since the expansion of the application of vehicle impoundment programs to other offences in Queensland. It was also recommended that the operational and resource costs of these laws should be compared to the road safety benefits in ongoing evaluations of effectiveness to ensure that finite traffic policing resources are allocated in a way that produces maximum road safety benefits. However, as the evidence of risk associated with the hooning driver is more compelling than that associated with hooning behaviour, it was argued that the hooning driver may represent the better target for intervention. Suggestions for future research include ongoing evaluations of the effectiveness of vehicle impoundment programs for hooning and other high-risk driving behaviours, and the exploration of additional potential targets for intervention to reduce hooning behaviour. As the body of knowledge regarding the factors contributing to hooning increases, along with the identification of potential barriers to the effectiveness of current countermeasures, recommendations for changes in policy and practice for hooning behaviours can be made.

“Teaching them a lesson?” : a qualitative exploration of underlying motivations for driver aggression

Aggressive driving is increasingly a concern for drivers in highly motorised countries. However, the role of driver intent in this behaviour is problematic and there is little research on driver cognitions in relation to aggressive driving incidents. In addition, while drivers who admit to behaving aggressively on the road also frequently report being recipients of similar behaviours, little is known about the relationship between perpetration and victimisation or about how road incidents escalate into the more serious events that feature in capture media attention. The current study used qualitative interviews to explore driver cognitions and underlying motivations for aggressive behaviours on the road. A total of 30 drivers aged 18-49 years were interviewed about their experiences with aggressive driving. A key theme identified in responses was driver aggression as an attempt to manage or modify the behaviour of other road users. Two subthemes were identified and appeared related to separate motivations for aggressive responses: ‘teaching them a lesson’ referred to situations where respondents intended to convey criticism or disapproval, usually of unintended behaviours by the other driver, and thus encourage self-correction; and ‘justified retaliation’ which referred to situations where respondents perceived deliberate intent on the part of the other driver and responded aggressively in return. Mildly aggressive driver behaviour appears to be common. Moreover such behaviour has a sufficiently negative impact on other drivers that it may be worth addressing because of its potential for triggering retaliation in kind or escalation of aggression, thus compromising safety.

Asphalt concrete surfaces macrotexture determination from still images

Road surface macrotexture is identified as one of the factors contributing to the surface's skid resistance. Existing methods of quantifying the surface macrotexture, such as the sand patch test and the laser profilometer test, are either expensive or intrusive, requiring traffic control. High-resolution cameras have made it possible to acquire good quality images from roads for the automated analysis of texture depth. In this paper, a granulometric method based on image processing is proposed to estimate road surface texture coarseness distribution from their edge profiles. More than 1300 images were acquired from two different sites, extending to a total of 2.96 km. The images were acquired using camera orientations of 60 and 90 degrees. The road surface is modeled as a texture of particles, and the size distribution of these particles is obtained from chord lengths across edge boundaries. The mean size from each distribution is compared with the sensor measured texture depth obtained using a laser profilometer. By tuning the edge detector parameters, a coefficient of determination of up to R2 = 0.94 between the proposed method and the laser profilometer method was obtained. The high correlation is also confirmed by robust calibration parameters that enable the method to be used for unseen data after the method has been calibrated over road surface data with similar surface characteristics and under similar imaging conditions.