Near real-time prediction of Zenith Tropospheric Delays for position estimation over long-baseline CORS network

This paper presents the preliminary results in establishing a strategy for predicting Zenith Tropospheric Delay (ZTD) and relative ZTD (rZTD) between Continuous Operating Reference Stations (CORS) in near real-time. It is anticipated that the predicted ZTD or rZTD can assist the network-based Real-Time Kinematic (RTK) performance over long inter-station distances, ultimately, enabling a cost effective method of delivering precise positioning services to sparsely populated regional areas, such as Queensland. This research firstly investigates two ZTD solutions: 1) the post-processed IGS ZTD solution and 2) the near Real-Time ZTD solution. The near Real-Time solution is obtained through the GNSS processing software package (Bernese) that has been deployed for this project. The predictability of the near Real-Time Bernese solution is analyzed and compared to the post-processed IGS solution where it acts as the benchmark solution. The predictability analyses were conducted with various prediction time of 15, 30, 45, and 60 minutes to determine the error with respect to timeliness. The predictability of ZTD and relative ZTD is determined (or characterized) by using the previously estimated ZTD as the predicted ZTD of current epoch. This research has shown that both the ZTD and relative ZTD predicted errors are random in nature; the STD grows from a few millimeters to sub-centimeters while the predicted delay interval ranges from 15 to 60 minutes. Additionally, the RZTD predictability shows very little dependency on the length of tested baselines of up to 1000 kilometers. Finally, the comparison of near Real-Time Bernese solution with IGS solution has shown a slight degradation in the prediction accuracy. The less accurate NRT solution has an STD error of 1cm within the delay of 50 minutes. However, some larger errors of up to 10cm are observed.

The influence of travel time and size of shopping center towards the frequencies of visiting customers in shopping centers in surabaya

Visiting a modern shopping center is becoming vital in our society nowadays. The fast growth of shopping center, transportation system, and modern vehicles has given more choices for consumers in shopping. Although there are many reasons for the consumers in visiting the shopping center, the influence of travel time and size of shopping center are important things to be considered towards the frequencies of visiting customers in shopping centers. A survey to the customers of three major shopping centers in Surabaya has been conducted to evaluate the Ellwood’s model and Huff’s model. A new exponent value N of 0.48 and n of 0.50 has been found from the Ellwood’s model, while a coefficient of 0.267 and an add value of 0.245 have been found from the Huff’s model.

Design of automatic vision-based inspection system for solder joint segmentation

Purpose: Computer vision has been widely used in the inspection of electronic components. This paper proposes a computer vision system for the automatic detection, localisation, and segmentation of solder joints on Printed Circuit Boards (PCBs) under different illumination conditions. Design/methodology/approach: An illumination normalization approach is applied to an image, which can effectively and efficiently eliminate the effect of uneven illumination while keeping the properties of the processed image the same as in the corresponding image under normal lighting conditions. Consequently special lighting and instrumental setup can be reduced in order to detect solder joints. These normalised images are insensitive to illumination variations and are used for the subsequent solder joint detection stages. In the segmentation approach, the PCB image is transformed from an RGB color space to a YIQ color space for the effective detection of solder joints from the background. Findings: The segmentation results show that the proposed approach improves the performance significantly for images under varying illumination conditions. Research limitations/implications: This paper proposes a front-end system for the automatic detection, localisation, and segmentation of solder joint defects. Further research is required to complete the full system including the classification of solder joint defects. Practical implications: The methodology presented in this paper can be an effective method to reduce cost and improve quality in production of PCBs in the manufacturing industry. Originality/value: This research proposes the automatic location, identification and segmentation of solder joints under different illumination conditions.

Automatic solder joint defect classification using the Log-Gabor filter

This paper proposes the validity of a Gabor filter bank for feature extraction of solder joint images on Printed Circuit Boards (PCBs). A distance measure based on the Mahalanobis Cosine metric is also presented for classification of five different types of solder joints. From the experimental results, this methodology achieved high accuracy and a well generalised performance. This can be an effective method to reduce cost and improve quality in the production of PCBs in the manufacturing industry.

Holding cost model for Greenfield Housing developments

Presentation provided to a PhD Colloquium between two Australian and one Malaysian University providing the opportunity to inform and critique progress of students concerning their selected topic. This presentation essentially involves "The conceptualisation, sensitivity and measurement of holding costs and other selected elements impacting housing affordability" as provided by Gary Owen Garner of QUT, with research objectives thus: 1. To establish the nature and composition of holding costs over time, as related to residential property in Australia, and internationally. 2. To examine the linkages that may exist between various planning instruments, the length of regulatory assessment periods, and housing affordability. 3. To develop a model that quantifies the impact of holding costs on housing affordability in Australia, with a particular focus on the consequences of extended assessment periods as a component of holding costs. Thus, provide clarification as to the impact of holding costs on overall housing affordability.

Droop control of converter interfaced micro sources in rural distributed generation

This paper proposes new droop control methods for load sharing in a rural area with distributed generation. Highly resistive lines, typical of rural low voltage networks, always create a big challenge for conventional droop control. To overcome the conflict between higher feedback gain for better power sharing and system stability in angle droop, two control methods have been proposed. The first method considers no communication among the distributed generators (DGs) and regulates the converter output voltage and angle ensuring proper sharing of load in a system having strong coupling between real and reactive power due to high line resistance. The second method, based on a smattering of communication, modifies the reference output volt-age angle of the DGs depending on the active and reactive power flow in the lines connected to point of common coupling (PCC). It is shown that with the second proposed control method, an economical and minimum communication system can achieve significant improvement in load sharing. The difference in error margin between proposed control schemes and a more costly high bandwidth communication system is small and the later may not be justified considering the increase in cost. The proposed control shows stable operation of the system for a range of operating conditions while ensuring satisfactory load sharing.

Analysis of phasor measurement method in tracking the power frequency of distorted signals

This paper presents an analysis of phasor measurement method for tracking the fundamental power frequency to show if it has the performance necessary to cope with the requirements of power system protection and control. In this regard, several computer simulations presenting the conditions of a typical power system signal especially those highly distorted by harmonics, noise and offset, are provided to evaluate the response of the Phasor Measurement (PM) technique. A new method, which can shorten the delay of estimation, has also been proposed for the PM method to work for signals free of even-order harmonics.

Development of a method to measure upper eyelid pressure on the cornea

Purpose: The cornea is known to be susceptible to forces exerted by eyelids. There have been previous attempts to quantify eyelid pressure but the reliability of the results is unclear. The purpose of this study was to develop a technique using piezoresistive pressure sensors to measure upper eyelid pressure on the cornea. Methods: The technique was based on the use of thin (0.18 mm) tactile piezoresistive pressure sensors, which generate a signal related to the applied pressure. A range of factors that influence the response of this pressure sensor were investigated along with the optimal method of placing the sensor in the eye. Results: Curvature of the pressure sensor was found to impart force, so the sensor needed to remain flat during measurements. A large rigid contact lens was designed to have a flat region to which the sensor was attached. To stabilise the contact lens during measurement, an apparatus was designed to hold and position the sensor and contact lens combination on the eye. A calibration system was designed to apply even pressure to the sensor when attached to the contact lens, so the raw digital output could be converted to actual pressure units. Conclusions: Several novel procedures were developed to use tactile sensors to measure eyelid pressure. The quantification of eyelid pressure has a number of applications including eyelid reconstructive surgery and the design of soft and rigid contact lenses.

A summary view of government cost recovery policies in Australia and New Zealand relating to the supply of public sector information

Researching administrative history is problematical. A trail of authoritative documents is often hard to find; and useful summaries can be difficult to organise, especially if source material is in paper formats in geographically dispersed locations. In the absence of documents, the reasons for particular decisions and the rationale underpinning particular policies can be confounded as key personnel advance in their professions and retire. The rationale for past decisions may be lost for practical purposes; and if an organisation’s memory of events is diminished, its learning through experience is also diminished. Publishing this document tries to avoid unnecessary duplication of effort by other researchers that need to venture into how policies of charging for public sector information have been justified. The author compiled this work within a somewhat limited time period and the work does not pretend to be a complete or comprehensive analysis of the issues.----- A significant part of the role of government is to provide a framework of legally-enforceable rights and obligations that can support individuals and non-government organisations in their lawful activities. Accordingly, claims that governments should be more ‘business-like’ need careful scrutiny. A significant supply of goods and services occurs as non-market activity where neither benefits nor costs are quantified within conventional accounting systems or in terms of money. Where a government decides to provide information as a service; and information from land registries is archetypical, the transactions occur as a political decision made under a direct or a clearly delegated authority of a parliament with the requisite constitutional powers. This is not a market transaction and the language of the market confuses attempts to describe a number of aspects of how governments allocate resources.----- Cost recovery can be construed as an aspect of taxation that is a sole prerogative of a parliament. The issues are fundamental to political constitutions; but they become more complicated where states cede some taxing powers to a central government as part of a federal system. Nor should the absence of markets be construed necessarily as ‘market failure’ or even ‘government failure’. The absence is often attributable to particular technical, economic and political constraints that preclude the operation of markets. Arguably, greater care is needed in distinguishing between the polity and markets in raising revenues and allocating resources; and that needs to start by removing unhelpful references to ‘business’ in the context of government decision-making.

Metaheuristic approaches to the hybrid flow shop scheduling problem with a cost-related criterion

In the paper, the flow-shop scheduling problem with parallel machines at each stage (machine center) is studied. For each job its release and due date as well as a processing time for its each operation are given. The scheduling criterion consists of three parts: the total weighted earliness, the total weighted tardiness and the total weighted waiting time. The criterion takes into account the costs of storing semi-manufactured products in the course of production and ready-made products as well as penalties for not meeting the deadlines stated in the conditions of the contract with customer. To solve the problem, three constructive algorithms and three metaheuristics (based one Tabu Search and Simulated Annealing techniques) are developed and experimentally analyzed. All the proposed algorithms operate on the notion of so-called operation processing order, i.e. the order of operations on each machine. We show that the problem of schedule construction on the base of a given operation processing order can be reduced to the linear programming task. We also propose some approximation algorithm for schedule construction and show the conditions of its optimality.

Website physical activity interventions : preferences of potential users

Information and communication technologies (particularly websites and e-mail) have the potential to deliver health behavior change programs to large numbers of adults at low cost. Controlled trials using these new media to promote physical activity have produced mixed results. User-centered development methods can assist in understanding the preferences of potential participants for website functions and content, and may lead to more effective programs. Eight focus group discussions were conducted with 40 adults after they had accessed a previously trialed physical activity website. The discussions were audio taped, transcribed and interpreted using a themed analysis method. Four key themes emerged: structure, interactivity, environmental context and content. Preferences were expressed for websites that include simple interactive features, together with information on local community activity opportunities. Particular suggestions included online community notice boards, personalized progress charts, e-mail access to expert advice and access to information on specific local physical activity facilities and services. Website physical activity interventions could usefully include personally relevant interactive and environmentally focused features and services identified through a user-centered development process.