An ultraviolet selective photodetector based on a nanocrystalline TiO2 photoelectrochemical cell

Solar ultraviolet (UV) radiation causes a range of skin disorders as well as affecting vision and the immune system. It also inhibits development of plants and animals. UV radiation monitoring is used routinely in some locations in order to alert the population to harmful solar radiation levels. There is ongoing research to develop UV-selective-sensors [1–3]. A personal, inexpensive and simple UV-selective-sensor would be desirable to measure UV intensity exposure. A prototype of such a detector has been developed and evaluated in our laboratory. It comprises a sealed two-electrode photoelectrochemical cell (PEC) based on nanocrystalline TiO2. This abundant semiconducting oxide, which is innocuous and very sta-ble, is the subject of intense study at present due to its application in dye sensitized solar cells (DSSC) [4]. Since TiO2 has a wide band gap (EG = 3.0 eV for rutile and EG = 3.2 eV for anatase), it is inher-ently UV-selective, so that UV filters are not required. This further reduces the cost of the proposed photodetector in comparison with conventional silicon detectors. The PEC is a semiconductor–electrolyte device that generates a photovoltage when it is illuminated and a corresponding photocur-rent if the external circuit is closed. The device does not require external bias, and the short circuit current is generally a linear function of illumination intensity. This greatly simplifies the elec-trical circuit needed when using the PEC as a photodetector. DSSC technology, which is based on a PEC containing nanocrystalline TiO2 sensitized with a ruthenium dye, holds out the promise of solar cells that are significantly cheaper than traditional silicon solar cells. The UV-sensor proposed in this paper relies on the cre-ation of electron–hole pairs in the TiO2 by UV radiation, so that it would be even cheaper than a DSSC since no sensitizer dye is needed. Although TiO2 has been reported as a suitable material for UV sensing [3], to the best of our knowledge, the PEC configuration described in the present paper is a new approach. In the present study, a novel double-layer TiO2 structure has been investigated. Fabrication is based on a simple and inexpensive technique for nanostructured TiO2 deposition using microwave-activated chemical bath deposition (MW-CBD) that has been reported recently [5]. The highly transparent TiO2 (anatase) films obtained are densely packed, and they adhere very well to the transparent oxide (TCO) substrate [6]. These compact layers have been studied as contacting layers in double-layer TiO2 structures for DSSC since improvement of electron extraction at the TiO2–TCO interface is expected [7]. Here we compare devices incorporating a single mesoporous nanocrystalline TiO2 structure with devices based on a double structure in which a MW-CBD film is situated between the TCO and the mesoporous nanocrystalline TiO2 layer. Besides improving electron extraction, this film could also help to block recombination of electrons transferred to the TCO with oxidized species in the electrolyte, as has been reported in the case of DSSC for compact TiO2 films obtained by other deposition tech-niques [8,9]. The two types of UV-selective sensors were characterized in detail. The current voltage characteristics, spectral response, inten-sity dependence of short circuit current and response times were measured and analyzed in order to evaluate the potential of sealed mesoporous TiO2-based photoelectrochemical cells (PEC) as low cost personal UV-photodetectors.

The theories of reasoned action and planned behaviour applied to business decision : a selective annotated bibliography

Purpose: This paper provides a selective annotated bibliography that summarises journal articles which have employed either the theory of reasoned action or the theory of planned behaviour to circumstances which are relevant to business activities. Design/methodology/approach: Searches were conducted on the EBSCO Host and ProQuest databases to identify papers that had used either the theory of reasoned action or theory of planned behaviour in their methodology. The bibliography was separated into three categories- financial decision making, strategic decision making, and professional decision making. Implications: The information presented in this paper is intended to assist and facilitate further research by broadening the awareness of the literature and providing examples of the application of the theory as it has been employed in prior research.

Responding to rapid change in higher education : enabling university departments responsible for work related programs through boundary spanning

Boundary spanning links organisations to one another in order to create mutually beneficial relationships; it is a concept developed and used in organisational theory but rarely used to understand organisational structures in higher education (Pruitt & Schwartz, 1999). Yet understanding boundary spanning activity has the capacity to help universities respond to demands for continuous quality improvement, and to increase capacity to react to environmental uncertainty. At a time of rapid change characterised by a fluctuating economic environment, globalisation, increased mobility, and ecological issues, boundary spanning could be viewed as a key element in assisting institutions in effectively understanding and responding to such change. The literature suggests that effective boundary spanning could help universities improve organisational performance, use of infrastructure and resources, intergroup relations, leadership styles, performance and levels of job satisfaction, technology transfer, knowledge creation, and feedback processes, amongst other things. Our research aims to put a face on boundary spanning (Miller, 2008) by contextualising it within organisational systems and structures in university departments responsible for work related programs i.e. Work Integrated Learning (WIL) and Co-operative Education (Co-op). In this paper these approaches are referred to collectively as work related programs. The authors formed a research team in Victoria, British Columbia in 2009 at a sponsored international research forum, Two Days in June. The purpose of the invitation-only forum was to investigate commonalities and differences across programs and to formulate an international research agenda for work related programs over the next five to ten years. Researchers from Queensland University of Technology, University of Cincinnati, Baden-Wuerttemberg Cooperative State University, University of Ottawa,and Dublin City University agreed that further research was needed into the impact stakeholders, organisational systems, structures, policies, and practices have on departments delivering work related programs. This paper illustrates how policy and practice across the five institutions can be better understood through the lens of boundary spanning. It is argued that boundary spanning is an area of theory and practice with great applicability to a better understanding of the activity of these departments. The paper concludes by proposing topics for future research to examine how boundary spanning can be used to better understand practice and change in work related programs.

Developing a model of embedding academic numeracy in university programs : a case study from nursing

This is a study of the academic numeracy of nursing students. This study develops a theoretical model for the design and delivery of university courses in academic numeracy. The following objectives are addressed: 1. To investigate nursing students' current knowledge of academic numeracy; 2. To investigate how nursing students’ knowledge and skills in academic numeracy can be enhanced using a developmental psychology framework; and 3. To utilise data derived from meeting objectives 1 and 2 to develop a theoretical model to embed academic numeracy in university programs. This study draws from Valsiner’s Human Development Theory (Valsiner, 1997, 2007). It is a quasi-experimental intervention case study (Faltis, 1997) and takes a multimethod approach using pre- and post-tests; observation notes; and semi-structured teaching sessions to document a series of microgenetic studies of student numeracy. Each microgenetic study is centered on the lived experience of students becoming more numerate. The method for this section is based on Vygotsky’s double stimulation (Valsiner, 2000a; 2007). Data collection includes interviews on students’ past experience with mathematics; their present feelings and experiences and how these present feelings and experiences are transformed. The findings from this study have provided evidence that the course developed for nursing students, underpinned by an appropriate framework, does improve academic numeracy. More specifically, students improved their content knowledge of and confidence in mathematics in areas that were directly related to their degree. The study used Valsiner’s microgenetic approach to development to trace the course as it was being taught and two students’ personal academic numeracy journeys. It highlighted particularly troublesome concepts, then outlined scaffolding and pathways used to develop understanding. This approach to academic numeracy development was summarised into a four-faceted model at the university, program, course and individual level. This model can be applied successfully to similar contexts. Thus the thesis advances both theory and practice in this under-researched and under-theorised area.

Quantification of particle emission characteristics and development of an emission model for use in transport microenvironments affected by traffic emissions

Vehicle emitted particles are of significant concern based on their potential to influence local air quality and human health. Transport microenvironments usually contain higher vehicle emission concentrations compared to other environments, and people spend a substantial amount of time in these microenvironments when commuting. Currently there is limited scientific knowledge on particle concentration, passenger exposure and the distribution of vehicle emissions in transport microenvironments, partially due to the fact that the instrumentation required to conduct such measurements is not available in many research centres. Information on passenger waiting time and location in such microenvironments has also not been investigated, which makes it difficult to evaluate a passenger’s spatial-temporal exposure to vehicle emissions. Furthermore, current emission models are incapable of rapidly predicting emission distribution, given the complexity of variations in emission rates that result from changes in driving conditions, as well as the time spent in driving condition within the transport microenvironment. In order to address these scientific gaps in knowledge, this work conducted, for the first time, a comprehensive statistical analysis of experimental data, along with multi-parameter assessment, exposure evaluation and comparison, and emission model development and application, in relation to traffic interrupted transport microenvironments. The work aimed to quantify and characterise particle emissions and human exposure in the transport microenvironments, with bus stations and a pedestrian crossing identified as suitable research locations representing a typical transport microenvironment. Firstly, two bus stations in Brisbane, Australia, with different designs, were selected to conduct measurements of particle number size distributions, particle number and PM2.5 concentrations during two different seasons. Simultaneous traffic and meteorological parameters were also monitored, aiming to quantify particle characteristics and investigate the impact of bus flow rate, station design and meteorological conditions on particle characteristics at stations. The results showed higher concentrations of PN20-30 at the station situated in an open area (open station), which is likely to be attributed to the lower average daily temperature compared to the station with a canyon structure (canyon station). During precipitation events, it was found that particle number concentration in the size range 25-250 nm decreased greatly, and that the average daily reduction in PM2.5 concentration on rainy days compared to fine days was 44.2 % and 22.6 % at the open and canyon station, respectively. The effect of ambient wind speeds on particle number concentrations was also examined, and no relationship was found between particle number concentration and wind speed for the entire measurement period. In addition, 33 pairs of average half-hourly PN7-3000 concentrations were calculated and identified at the two stations, during the same time of a day, and with the same ambient wind speeds and precipitation conditions. The results of a paired t-test showed that the average half-hourly PN7-3000 concentrations at the two stations were not significantly different at the 5% confidence level (t = 0.06, p = 0.96), which indicates that the different station designs were not a crucial factor for influencing PN7-3000 concentrations. A further assessment of passenger exposure to bus emissions on a platform was evaluated at another bus station in Brisbane, Australia. The sampling was conducted over seven weekdays to investigate spatial-temporal variations in size-fractionated particle number and PM2.5 concentrations, as well as human exposure on the platform. For the whole day, the average PN13-800 concentration was 1.3 x 104 and 1.0 x 104 particle/cm3 at the centre and end of the platform, respectively, of which PN50-100 accounted for the largest proportion to the total count. Furthermore, the contribution of exposure at the bus station to the overall daily exposure was assessed using two assumed scenarios of a school student and an office worker. It was found that, although the daily time fraction (the percentage of time spend at a location in a whole day) at the station was only 0.8 %, the daily exposure fractions (the percentage of exposures at a location accounting for the daily exposure) at the station were 2.7% and 2.8 % for exposure to PN13-800 and 2.7% and 3.5% for exposure to PM2.5 for the school student and the office worker, respectively. A new parameter, “exposure intensity” (the ratio of daily exposure fraction and the daily time fraction) was also defined and calculated at the station, with values of 3.3 and 3.4 for exposure to PN13-880, and 3.3 and 4.2 for exposure to PM2.5, for the school student and the office worker, respectively. In order to quantify the enhanced emissions at critical locations and define the emission distribution in further dispersion models for traffic interrupted transport microenvironments, a composite line source emission (CLSE) model was developed to specifically quantify exposure levels and describe the spatial variability of vehicle emissions in traffic interrupted microenvironments. This model took into account the complexity of vehicle movements in the queue, as well as different emission rates relevant to various driving conditions (cruise, decelerate, idle and accelerate), and it utilised multi-representative segments to capture the accurate emission distribution for real vehicle flow. This model does not only helped to quantify the enhanced emissions at critical locations, but it also helped to define the emission source distribution of the disrupted steady flow for further dispersion modelling. The model then was applied to estimate particle number emissions at a bidirectional bus station used by diesel and compressed natural gas fuelled buses. It was found that the acceleration distance was of critical importance when estimating particle number emission, since the highest emissions occurred in sections where most of the buses were accelerating and no significant increases were observed at locations where they idled. It was also shown that emissions at the front end of the platform were 43 times greater than at the rear of the platform. The CLSE model was also applied at a signalled pedestrian crossing, in order to assess increased particle number emissions from motor vehicles when forced to stop and accelerate from rest. The CLSE model was used to calculate the total emissions produced by a specific number and mix of light petrol cars and diesel passenger buses including 1 car travelling in 1 direction (/1 direction), 14 cars / 1 direction, 1 bus / 1 direction, 28 cars / 2 directions, 24 cars and 2 buses / 2 directions, and 20 cars and 4 buses / 2 directions. It was found that the total emissions produced during stopping on a red signal were significantly higher than when the traffic moved at a steady speed. Overall, total emissions due to the interruption of the traffic increased by a factor of 13, 11, 45, 11, 41, and 43 for the above 6 cases, respectively. In summary, this PhD thesis presents the results of a comprehensive study on particle number and mass concentration, together with particle size distribution, in a bus station transport microenvironment, influenced by bus flow rates, meteorological conditions and station design. Passenger spatial-temporal exposure to bus emitted particles was also assessed according to waiting time and location along the platform, as well as the contribution of exposure at the bus station to overall daily exposure. Due to the complexity of the interrupted traffic flow within the transport microenvironments, a unique CLSE model was also developed, which is capable of quantifying emission levels at critical locations within the transport microenvironment, for the purpose of evaluating passenger exposure and conducting simulations of vehicle emission dispersion. The application of the CLSE model at a pedestrian crossing also proved its applicability and simplicity for use in a real-world transport microenvironment.

Knowledge management in law enforcement : knowledge views for patrolling police officers

This paper describes and classifies different types of knowledge that are a part of police patrol officer's practice. Even though an investigation usually forces a police officer to apply several different knowledge types, this paper discusses different forms of professional knowledge separately to enable categorisation.

Spatial/surveying programs repositioning within new STEM Faculty at QUT

Many of the undergraduate and postgraduate programs of the former Faculty of Built Environment and Engineering PLUS Faculty of Sciences and Technology are changing as a result of merging these two large organisations, with some disciplines relocating to faculties of Creative Industries and Health respectively. The new STEM precinct under construction has begun rising from the proverbial hole-in-the-ground. Existing Surveying and Spatial Sciences programs, assets and staff are being repositioned with the newly formed School of Earth, Environment and Biological Sciences.2011. Golden graduates morning tea organised by QUT Alumni. Technology upgrades to the Mapping Sciences lab benefits 3-D learning experiences. Second and third-year students are undertaking Work Integrated Learning (WIL) over the summer vacation period. Final year students recently presented capstone project presentations at mini-conference in the Gibson Rooms overlooking a vibrant Southbank and sparkling Brisbane River. Discussion on end of year graduation ceremony held at QPAC.

The impact of completing a drink driving rehabilitation program on future drinking : the clients’ perspective

The paper explores the role and focus of drink driving rehabilitation programs. It is particularly concerned with whether programs that specifically focus on reducing driving after drinking also have a positive effect on clients’ levels of drinking. A sample of volunteering clients was recruited while they were participating in the Australian “Under the Limit” program and they were followed up at least three months post completion. Response rates were very low and the sample is assumed to reflect the views and outcomes of persons who felt positive about the program. Clients reported large and meaningful reductions in their drinking and in their drink driving. They also reported important moves towards action and change in their drinking habits. The findings deserve to be followed up given the fact that drink driving programs are generally of much shorter duration than alcohol focussed interventions. There is a need for further research in this area and for developing more effective recruitment strategies.

Impact of urban traffic and climate change on water quality from road runoff

Urban traffic and climate change are two phenomena that have the potential to degrade urban water quality by influencing the build-up and wash-off of pollutants, respectively. However, limited knowledge has made it difficult to establish any link between pollutant buildup and wash-off under such dynamic conditions. In order to safeguard urban water quality, adaptive water quality mitigation measures are required. In this research, pollutant build-up and wash-off have been investigated from a dynamic point of view which incorporated the impacts of changed urban traffic as well as changes in the rainfall characteristics induced by climate change. The study has developed a dynamic object classification system and thereby, conceptualised the study of pollutant build-up and wash-off under future changes in urban traffic and rainfall characteristics. This study has also characterised the buildup and wash-off processes of traffic generated heavy metals, volatile, semi-volatile and non-volatile hydrocarbons under dynamic conditions which enables the development of adaptive mitigation measures for water quality. Additionally, predictive frameworks for the build-up and wash-off of some pollutants have also been developed.

Design on the future: developing and enacting sustainable living programs in primary schools

Sustainable living is high on the international agenda (Ginsberg & Frame, 2004; Sutton, 2004). If education is fundamental to global transformation towards sustainability, then schools are in strategic positions to facilitate this change. Over recent years, schools in Australia have become more active in encouraging sustainability with the implementation of programs such as Science Education for Sustainable Living (SESL) that focus on topics such as energy efficiency, recycling, enhancing biodiversity, protecting species, and managing resources. This paper reports on a government funded Australian School Innovation in Science, Technology and Mathematics (ASISTM) project titled “Integrating science, technology and mathematics for understanding sustainable living” in which teachers, preservice teachers and other science professionals worked collaboratively to plan and enact a range of SESL programs for primary school students. Participants in this study included: 6 teachers, 5 preservice teachers, 2 university partners, 2 scientists, 4 consultants, and over 250 primary students. The findings from this qualitative study revealed a need for: (1) professional development for understanding SESL, (2) procedures for establishing and implementing SESL, and (3) strategies to devise, implement and evaluate SESL units of work.

Stepwise refinement of interrupt-driven real-time programs

Embedded real-time programs rely on external interrupts to respond to events in their physical environment in a timely fashion. Formal program verification theories, such as the refinement calculus, are intended for development of sequential, block-structured code and do not allow for asynchronous control constructs such as interrupt service routines. In this article we extend the refinement calculus to support formal development of interrupt-dependent programs. To do this we: use a timed semantics, to support reasoning about the occurrence of interrupts within bounded time intervals; introduce a restricted form of concurrency, to model composition of interrupt service routines with the main program they may preempt; introduce a semantics for shared variables, to model contention for variables accessed by both interrupt service routines and the main program; and use real-time scheduling theory to discharge timing requirements on interruptible program code.

An examination of the microscopic simulation models to identify traffic safety indicators

Evaluating the safety of different traffic facilities is a complex and crucial task. Microscopic simulation models have been widely used for traffic management but have been largely neglected in traffic safety studies. Micro simulation to study safety is more ethical and accessible than the traditional safety studies, which only assess historical crash data. However, current microscopic models are unable to mimic unsafe driver behavior, as they are based on presumptions of safe driver behavior. This highlights the need for a critical examination of the current microscopic models to determine which components and parameters have an effect on safety indicator reproduction. The question then arises whether these safety indicators are valid indicators of traffic safety. The safety indicators were therefore selected and tested for straight motorway segments in Brisbane, Australia. This test examined the capability of a micro-simulation model and presents a better understanding of micro-simulation models and how such models, in particular car following models can be enriched to present more accurate safety indicators.

A review of road traffic noise indicators and their correlation with the LA10(18hour)

This paper outlines a study to determine the correlation between the LA10(18hour) and other road traffic noise indicators. It is based on a database comprising of 404 measurement locations including 947 individual days of valid noise measurements across numerous circumstances taken between November 2001 and November 2007. This paper firstly discusses the need and constraints on the indicators and their nature of matching a suitable indicator to the various road traffic noise dynamical characteristics. The paper then presents a statistical analysis of the road traffic noise monitoring data, correlating various indicators with the LA10(18hour) statistical indicator and provides a comprehensive table of linear correlations. There is an extended analysis on relationships across the night time period. The paper concludes with a discussion on the findings.

Raising awareness of traffic pollution: the potential benefits and problems of using a warning smell

Exposure to traffic pollution is increasing worldwide as people move to cities, and as more vehicles join the roads, creating longer journeys and more traffic jams. Most traffic pollutants are odourless and invisible, which hides exposure from the public. If traffic pollution had a distinctive smell it would enable people to avoid exposure, and increase the political will for difficult policy changes. A smell may also instigate longer-term changes, such as switching to active transport for school pick-ups. A smell could be added using a fuel additive or a temporary device attached to vehicle exhausts.

Trends in policies, programs and practices in the Australasian First Year Experience literature 2000-2010. The First Year in Higher Education Research Series on Evidence-based Practice. Number 1

This publication is the first in a series of scholarly reports on research-based practice related to the First Year Experience in Higher Education. This report synthesises evidence about practice-based initiatives and pragmatic approaches in Aotearoa (New Zealand) and Australia that aim to enhance the experience of commencing students in the higher education sector. Trends in policies, programs and practices ... examines the first year experience literature from 2000-2010. It acknowledges the uniqueness of the Australasian socio-political context and its influence on the interests and output of researchers. The review surveyed almost 400 empirical reports and conceptual discussions produced over the decade that dealt with the stakeholders, institutions and the higher education sector in Australasia. The literature is examined through two theoretical constructs or “lenses”: first, a set of first year curriculum design principles and second, the generational approach to describing the maturation of initiatives. These outcomes and suggested directions for further research provide the challenges and the opportunities for FYE adherents, both scholars and practitioners, to grapple with in the next decade.