Novel protective covering to enhance concrete resistance against projectile impact

A novel protective covering with a layered and staggered structure was proposed to protect concrete against projectile impact. Experimental study was conducted to investigate the ballistic behaviour of the concrete targets against 12.7 mm armour-piercing incendiary projectile at velocities ranging from 537.7 to 596.5 m/s. The results showed that the concrete targets with protective covering exhibited superior integrity with no damage on the distal surface, whereas the concrete targets without protective covering were fractured with penetrating cracks throughout the thickness of the target. Moreover, the protected concrete targets displayed significantly reduced penetration depth compared with the concrete targets without protective covering. The protective covering with epoxy adhesive interlayers had a bigger protection factor than that with silicone sealant interlayers, but the former suffered more severe damage than the latter.

Calcium phosphate flocs and the clarification of sugar cane juice from whole of crop harvesting

Sugar cane biomass is one of the most viable feedstocks for the production of renewable fuels and chemicals. Therefore, processing the whole of crop (WC) (i.e., stalk and trash, instead of stalk only) will increase the amount of available biomass for this purpose. However, effective clarification of juice expressed from WC for raw sugar manufacture is a major challenge because of the amounts and types of non-sucrose impurities (e.g., polysaccharides, inorganics, proteins, etc.) present. Calcium phosphate flocs are important during sugar cane juice clarification because they are responsible for the removal of impurities. Therefore, to gain a better understanding of the role of calcium phosphate flocs during the juice clarification process,the effects of impurities on the physicochemical properties of calcium phosphate flocs were examined using small-angle laser light scattering technique, attenuated total reflectance Fourier transformed infrared spectroscopy, and X-ray powder diffraction. Results on synthetic sugar juice solutions showed that the presence of SiO2 and Na+ ions affected floc size and floc structure. Starch and phosphate ions did not affect the floc structure; however, the former reduced the floc size, whereas the latter increased the floc size. The study revealed that high levels of Na+ ions would negatively affect the clarification process the most, as they would reduce the amount of suspended particles trapped by the flocs. A complementary study on prepared WC juice using cold and cold/intermediate liming techniques was conducted. The study demonstrated that, in comparison to the one-stage (i.e., conventional) clarification process, a two-stage clarification process using cold liming removed more polysaccharides (≤19%),proteins (≤82%), phosphorus (≤53%), and SiO2 (≤23%) in WC juice but increased Ca2+ (≤136%) and sulfur (≤200%)

Budgie Smuggler: Selected work for 2015 Swell Sculpture Festival

Budgie Smuggler is the first work of a series entitled slang, reflecting upon other, often unintended meanings behind popular Australian expressions. Synonymous with Australian beach humour, the term budgie smuggler unintentionally masks the desperately tragic plight of wildlife trafficked every year within and beyond our borders. Bird wildlife are fiercely protectively of their kin, often flocking to a site of distress of those trapped or injured - a commotion ensues, helping to scare predators away. The work contemplates our own position and action in response to our captive feathered friends. Budgie Smuggler is a soft resin/silicon, cotton material, fibreglass and recycled object based artwork.

Speed-based diagnostics of aerodynamic and mass imbalance in large wind turbines

Any kind of imbalance in the operation of a wind turbine has adverse effect on the downstream torsional components as well as tower structure. It is crucial to detect imbalance at its very inception. The identification of the type of imbalance is also required so that appropriate measures of fault accommodation can be performed in the control system. In particular, it is important to distinguish between mass and aerodynamic imbalance. While the former is gradually caused by a structural anomaly (e.g. ice deposition, moisture accumulation inside blade), the latter is generally associated to a fault in the pitch control system. This paper proposes a technique for the detection and identification of imbalance fault in large scale wind turbines. Unlike most other existing method it requires only the rotor speed signal which is readily available in existing turbines. Signature frequencies have been proposed in this work to identify imbalance type based on their physical phenomenology. The performance of this technique has been evaluated by simulations using an existing benchmark model. The effectiveness of the proposed method has been confirmed by the simulation results.

PEOPLE and PLACE: lecture notes and workshops

This a compilation of lecture notes and tutorial workshops that were prepared for the former QUT unit DLB310 People and Place. This unit introduced second year students to fundamental ideas about environmental psychology and cultural landscape theory for landscape architects.

A comparative study of two design charrettes: Implications for codesign and participatory action research

The purpose of this paper is to explore how participatory prototyping, through the use of design charrettes, can advance participatory action research (PAR) approaches and contribute to codesign practices in organisational settings. This will be achieved through the comparison of two varying design charrette experiences from a PAR initiative to redesign spaces in the Auraria Library in Denver, Colorado. Each design charrette followed a three-stage sequence of information sharing, idea generation and prototyping, and prioritisation with each stage building upon the former, both in terms of design concepts and in building up elements of ‘making’. While both charrette structures were similar, leadership and execution varied considerably. Lessons learned from the two design charrette experiences are presented, including the value of participatory prototyping within PAR to support ‘research through design’ activities. In addition, it highlights the value of authentic design participation of ‘designing with’ rather than ‘designing for’ to encourage optimal design outcomes.

Radon-222 activity flux measurement using activated charcoal canisters: Revisiting the methodology

The measurement of radon ((222)Rn) activity flux using activated charcoal canisters was examined to investigate the distribution of the adsorbed (222)Rn in the charcoal bed and the relationship between (222)Rn activity flux and exposure time. The activity flux of (222)Rn from five sources of varying strengths was measured for exposure times of one, two, three, five, seven, 10, and 14 days. The distribution of the adsorbed (222)Rn in the charcoal bed was obtained by dividing the bed into six layers and counting each layer separately after the exposure. (222)Rn activity decreased in the layers that were away from the exposed surface. Nevertheless, the results demonstrated that only a small correction might be required in the actual application of charcoal canisters for activity flux measurement, where calibration standards were often prepared by the uniform mixing of radium ((226)Ra) in the matrix. This was because the diffusion of (222)Rn in the charcoal bed and the detection efficiency as a function of the charcoal depth tended to counterbalance each other. The influence of exposure time on the measured (222)Rn activity flux was observed in two situations of the canister exposure layout: (a) canister sealed to an open bed of the material and (b) canister sealed over a jar containing the material. The measured (222)Rn activity flux decreased as the exposure time increased. The change in the former situation was significant with an exponential decrease as the exposure time increased. In the latter case, lesser reduction was noticed in the observed activity flux with respect to exposure time. This reduction might have been related to certain factors, such as absorption site saturation or the back diffusion of (222)Rn gas occurring at the canister-soil interface.

The effect of thermal radiation on the natural convection boundary layer flow over a wavy horizontal surface

In this article, natural convection boundary layer flow is investigated over a semi-infinite horizontal wavy surface. Such an irregular (wavy) surface is used to exchange heat with an external radiating fluid which obeys Rosseland diffusion approximation. The boundary layer equations are cast into dimensionless form by introducing appropriate scaling. Primitive variable formulations (PVF) and stream function formulations (SFF) are independently used to transform the boundary layer equations into convenient form. The equations obtained from the former formulations are integrated numerically via implicit finite difference iterative scheme whereas equations obtained from lateral formulations are simulated through Keller-box scheme. To validate the results, solutions produced by above two methods are compared graphically. The main parameters: thermal radiation parameter and amplitude of the wavy surface are discussed categorically in terms of shear stress and rate of heat transfer. It is found that wavy surface increases heat transfer rate compared to the smooth wall. Thus optimum heat transfer is accomplished when irregular surface is considered. It is also established that high amplitude of the wavy surface in the boundary layer leads to separation of fluid from the plate.

Comparison of measured sleeping metabolic rate and predicted basal metabolic rate during the first year of life : evidence of a bias changing with increasing metabolic rate

Objective: To compare measurements of sleeping metabolic rate (SMR) in infancy with predicted basal metabolic rate (BMR) estimated by the equations of Schofield. Methods: Some 104 serial measurements of SMR by indirect calorimetry were performed in 43 healthy infants at 1.5, 3, 6, 9 and 12 months of age. Predicted BMR was calculated using the weight only (BMR-wo) and weight and height (BMR-wh) equations of Schofield for 0-3-y-olds. Measured SMR values were compared with both predictive values by means of the Bland-Altman statistical test. Results: The mean measured SMR was 1.48 MJ/day. The mean predicted BMR values were 1.66 and 1.47 MJ/day for the weight only and weight and height equations, respectively. The Bland-Altman analysis showed that BMR-wo equation on average overestimated SMR by 0.18 MJ/day (11%) and the BMR-wh equation underestimated SMR by 0.01 MJ/day (1%). However the 95% limits of agreement were wide: -0.64 to + 0.28 MJ/day (28%) for the former equation and -0.39 to + 0.41 MJ/day (27%) for the latter equation. Moreover there was a significant correlation between the mean of the measured and predicted metabolic rate and the difference between them. Conclusions: The wide variation seen in the difference between measured and predicted metabolic rate and the bias probably with age indicates there is a need to measure actual metabolic rate for individual clinical care in this age group.

The purposes of history? Curriculum studies, invisible objects and twenty-first century societies

A new intellectual epoch has generated new enterprises to suit changed beliefs and circumstances. A widespread sentiment in both formal historiography and curriculum studies reduces the “new” to the question of how knowledge is recognized as such, how it is gained, and how it is represented in narrative form. Whether the nature of history and conceptions of knowledge are, or ought to be, central considerations in curriculum studies and reducible to purposes or elevated as present orientated requires rethinking. This paper operates as an incitement to discourse that disrupts the protection and isolation of primary categories in the field whose troubling is overdue. In particular, the paper moves through several layers that highlight the lack of settlement regarding the endowment of objects for study with the status of the scientific. It traces how some “invisible” things have been included within the purview of curriculum history as objects of study and not others. The focus is the making of things deemed invisible into scientific objects (or not) and the specific site of analysis is the work of William James (1842-1910). James studied intensely both child mind and the ghost, the former of which becomes scientized and legitimated for further study, the latter abjected. This contrast opens key points for reconsideration regarding conditions of proof, validation criteria, and subject matters and points to opportunities to challenge some well-rehearsed foreclosures within progressive politics and education.

Examining novice education: What can we learn from a compulsory program delivered to both mature-age and young pre-learner licence drivers?

This paper reports results from a qualitative evaluation of a compulsory pre-Learner driver education program within the Australian Capital Territory(ACT), Australia. Two methods were used to obtain feedback from those involved in the delivery of the program as well as those who participated in programs. The first, semi-structured interviews, was undertaken with class room teachers who run the program in their schools, group facilitators running the program with more mature-age students at private facilities (n = 15 in total), and former participants in both school-based and private-based versions of the program (n = 19). The second method used an on-line survey for students (n = 79). Results from both methods were consistent with each other, indicating that strengths of the program were perceived as being its interactive components and the high level of engagement of the target audience. There was strong support from young and mature-age students for the program to remain compulsory. However, consistent with other findings on novice driver education, mature-age participants identified that the program was less relevant to them. It may be that to have greater relevance to mature-age learners, content could address and challenge perceptions about behaviours other than intentional high-risk behaviours (e.g. low level speeding, fatigue) as well as encourage planning/strategies to avoid them. While a longer term, outcome focussed, evaluation of the pre-learner education program is needed, this study suggests that the program is well received by pre-licence drivers and that teachers and facilitators perceive it as both effective and beneficial.

State Library Queensland

Sheona Thomson writes about the transformation of a public institution in relation to a study on post-occupancy. "Brisbanites like me, with memories of long hours of study in the former buildings of the State Library of Queensland, can only marvel at the living institution we have in our city today. For most of the 80s, our bookish pursuits were hosted in the fustily intimate reading rooms of Centennial Hall, the late 1950s extension to the nineteenth-century building (formerly housing the state museum) by F. D. G. Stanley in William Street on the north bank of the Brisbane River. At the time, the wheels of an expansive cultural ambition were turning, and piece by piece on the south bank of the river the rambling Queensland Cultural Centre was realized. The fourth stage of the complex opened in 1988 as the new home for the State Library and for many years after, countless studious, transient folk whiled away time in the deep interiors of the straight-faced concrete and glass edifice by Robin Gibson and Partners..."

The 'rise' of Aboriginal women, from domesticated cow to cash cow

The recent claims from former Queensland Labor MP Gary Johns that “a lot of poor women in this country, a large proportion of whom are Aboriginal, are used as cash cows” who are “kept pregnant and producing children for the cash” are somewhat alarming, but not surprising...

A multiscale study on the structural and mechanical properties of the luffa sponge from Luffa cylindrica plant

Cellular materials that are often observed in biological systems exhibit excellent mechanical properties at remarkably low densities. Luffa sponge is one of such materials with a complex interconnecting porous structure. In this paper, we studied the relationship between its structural and mechanical properties at different levels of its hierarchical organization from a single fiber to a segment of whole sponge. The tensile mechanical behaviors of three single fibers were examined by an Instron testing machine and the ultrastructure of a fractured single fiber was observed in a scanning electronic microscope. Moreover, the compressive mechanical behaviors of the foam-like blocks from different locations of the sponge were examined. The difference of the compressive stress-strain responses of four sets of segmental samples were also compared. The result shows that the single fiber is a porous composite material mainly consisting of cellulose fibrils and lignin/hemicellulose matrix, and its Young's modulus and strength are comparable to wood. The mechanical behavior of the block samples from the hoop wall is superior to that from the core part. Furthermore, it shows that the influence of the inner surface on the mechanical property of the segmental sample is stronger than that of the core part; in particular, the former's Young's modulus, strength and strain energy absorbed are about 1.6 times higher. The present work can improve our understanding of the structure-function relationship of the natural material, which may inspire fabrication of new biomimetic foams with desirable mechanical efficiency for further applications in anti-crushing devices and super-light sandwich panels.

Predicting health programme participation: A gravity‐based, hierarchical modelling approach

Statistical analyses of health program participation seek to address a number of objectives compatible with the evaluation of demand for current resources. In this spirit, a spatial hierarchical model is developed for disentangling patterns in participation at the small area level, as a function of population-based demand and additional variation. For the former, a constrained gravity model is proposed to quantify factors associated with spatial choice and account for competition effects, for programs delivered by multiple clinics. The implications of gravity model misspecification within a mixed effects framework are also explored. The proposed model is applied to participation data from a no-fee mammography program in Brisbane, Australia. Attention is paid to the interpretation of various model outputs and their relevance for public health policy.