Towards a model for student selection in clinical psychology

Background Selection of candidates for clinical psychology programmes is arguably the most important decision made in determining the clinical psychology workforce. However, there are few models to inform the development of selection tools to support selection procedures. The study, using a factor analytic structure, has operationalised the model predicting applicants' capabilities. Method Eighty-eight clinical applicants for entry into a postgraduate clinical psychology programme were assessed on a series of tasks measuring eight capabilities: guided reflection, communication skills, ethical decision making, writing, conceptual reasoning, empathy, and awareness of mind and self-observation. Results Factor analysis revealed three capabilities: labelled “awareness” accounting for 35.71% of variance; “reflection” accounting for 20.56%; and “reasoning” accounting for 18.24% of variance. Fourth year grade point average (GPA) did not correlate with performance on any of the selection capabilities other than a weak correlation with performance on the ethics capability. Conclusions Eight selection capabilities are identified for the selection of candidates independent of GPA. While the model is tentative, it is hoped that the findings will stimulate the development and validation of assessment procedures with good predictive validity which will benefit the training of clinical psychologists and, ultimately, effective service delivery.

Evolution of lure response in tephritid fruit flies : phytochemicals as drivers of sexual selection

The males of many Bactrocera species (Diptera: Tephritidae) respond strongly and positively to a small number of plant-derived chemicals (=male lures). Males that have imbibed the lures commonly have a mating advantage over unfed males, but no female benefits have been demonstrated for females mating with lure-fed males. It has been hypothesized that the strong lure response is a case of runaway selection, where males receive direct benefits and females receive indirect benefits via 'sexy sons', or a case of sensory bias where females have a lower threshold response to lures. To test these hypotheses we studied the effects of lure feeding on male mating, remating and longevity; while for females that had mated with lure-fed males we recorded mating refractoriness, fecundity, egg viability and longevity. We used Bactrocera tryoni as our test animal and as lures the naturally occurring zingerone and chemically related, but synthetic chemical cuelure. Feeding on lures provided direct male benefits in greater mating success and increased multiple mating. For the first time, we recorded direct female effects: increased fecundity and reduced remating receptivity. Egg viability did not differ in females mated with lure-fed or unfed males. The life span of males and females exposed to lures was reduced. These results reveal direct, current-generation fitness benefits for both males and females, although the male benefits appear greater. We discuss that while lure response is indeed likely to be a sexual selection trait, there is no need to invoke runaway selection to explain its evolution.

Genetic response to combined family selection for improved mean harvest weight in giant freshwater prawn (Macrobrachium rosenbergii) in Vietnam

We estimated genetic changes in body and carcass weight traits in a giant freshwater prawn (GFP) (Macrobrachium rosenbergii) population selected for increased body weight at harvest in Vietnam. The data set consisted of 18,387 individual body and 1730 carcass weight records, as well as full pedigree information collected over four generations. Average selection response (per generation) in body weight at harvest (transformed to square root) estimated as the difference between the Selection line and the Control group was 7.4% calculated from least squares mean (LSMs), 7.0% from estimated breeding values (EBVs) and 4.4% calculated from EBVs between two consecutive generations. Favorable correlated selection responses (estimated from LSMs) were found for other body traits including: total length, cephalothorax length, abdominal length, cephalothorax width, and abdominal width (12.1%, 14.5%, 10.4%, 15.5% and 13.3% over three selection generations, respectively). Data in the second generation of selection showed positive correlated responses for carcass weight traits including: abdominal weight, exoskeleton-off weight, and telson-off weight of 8.8%, 8.6% and 8.8%, respectively. We conclude that body weight at harvest responded well to the application of combined (between and within) family selection and correlated responses in carcass weight traits were favorable.

Cross-sectional study of a microsatellite marker in the low densitity lipoprotein receptor gene in obese normotensives

1. The low density lipoprotein receptor is an important regulator of serum cholesterol which may have implications for the development of both hypertension and obesity. In this study, genotypes for a low density lipoprotein receptor gene (LDLR) dinucleotide polymorphism were determined in both lean and obese normotensive populations. 2. In previous cross-sectional association studies an ApaLI and a HincII polymorphism for LDLR were shown to be associated with obesity in essential hypertensives. However, these polymorphisms did not show an association with obesity in normotensives. 3. In contrast, this study reports that preliminary results for an LDLR microsatellite marker, located more towards the 3' end of the gene, show a significant association with obesity in the normotensive population studied. These results indicate that LDLR could play an important role in the development of obesity, which might be independent of hypertension.

An interpretive field study of packaged software selection processes

Packaged software is pre-built with the intention of licensing it to users in domestic settings and work organisations. This thesis focuses upon the work organisation where packaged software has been characterised as one of the latest ‘solutions’ to the problems of information systems. The study investigates the packaged software selection process that has, to date, been largely viewed as objective and rational. In contrast, this interpretive study is based on a 21⁄2 year long field study of organisational experiences with packaged software selection at T.Co, a consultancy organisation based in the United Kingdom. Emerging from the iterative process of case study and action research is an alternative theory of packaged software selection. The research argues that packaged software selection is far from the rationalistic and linear process that previous studies suggest. Instead, the study finds that aspects of the traditional process of selection incorporating the activities of gathering requirements, evaluation and selection based on ‘best fit’ may or may not take place. Furthermore, even where these aspects occur they may not have equal weight or impact upon implementation and usage as may be expected. This is due to the influence of those multiple realities which originate from the organisational and market environments within which packages are created, selected and used, the lack of homogeneity in organisational contexts and the variously interpreted characteristics of the package in question.

Hysteretic multilevel NPC converter control for a Switch Mode Assisted Linear Amplifier

A Switch-Mode Assisted Linear Amplifier (SMALA) combines the high quality of a linear amplifier required for audio applications with the high efficiency of a switch-mode amplifier. The careful choice of current sense point and switch placement allows a simple non-isolated hysteresis current controller for the switch-mode section. This paper explains the extension of the hysteresis current controller for the control of a three level Neutral Point Clamped (NPC) converter, with simulations as proof of concept. The NPC topology allows the use of lower voltage switches and lower switching frequencies to implement high power audio amplifiers using the SMALA topology.

Selection of energy storage system for a regenerative dynamic dynamometer

This paper presents a design technique of a fully regenerative dynamic dynamometer. It incorporates an energy storage system to absorb the energy variation due to dynamometer transients. This allows the minimum power electronics requirement at the grid to supply the losses. The simulation results of the full system over a driving cycle show the amount of energy required to complete a driving cycle, therefore the size of the energy storage system can be determined.

Design optimisation of ironless motors based on magnet selection

This paper considers the design of a radial flux permanent magnet iron less core brushless DC motor for use in an electric wheel drive with an integrated epicyclic gear reduction. The motor has been designed for a continuous output torque of 30 Nm and peak rating of 60 Nm with a maximum operating speed of 7000 RPM. In the design of brushless DC motors with a toothed iron stator the peak air-gap magnetic flux density is typically chosen to be close to that of the remanence value of the magnets used. This paper demonstrates that for an ironless motor the optimal peak air-gap flux density is closer to the maximum energy product of the magnets used. The use of a radial flux topology allows for high frequency operation and can be shown to give high specific power output while maintaining a relatively low magnet mass. Two-dimensional finite element analysis is used to predict the air-gap flux density. The motor design is based around commonly available NdFeB bar magnet size

Design optimisation of ironless motors based on magnet selection

This paper considers the design of a radial flux permanent magnet ironless core brushless DC motor for use in an electric wheel drive with an integrated epicyclic gear reduction. The motor has been designed for a continuous output torque of 30 Nm and peak rating of 60 Nm with a maximum operating speed of 7000 RPM. In the design of brushless DC motors with a toothed iron stator the peak air-gap magnetic flux density is typically chosen to be close to that of the remanence value of the magnets used. This paper demonstrates that for an ironless motor the optimal peak air-gap flux density is closer to the maximum energy product of the magnets used. The use of a radial flux topology allows for high frequency operation and can be shown to give high specific power output while maintaining a relatively low magnet mass. Two-dimensional finite element analysis is used to predict the airgap flux density. The motor design is based around commonly available NdFeB bar magnet size

A method of switch selection for an electric vehicle drive

The key to reducing cost of electric vehicles is integration. All too often systems such as the motor, motor controller, batteries and vehicle chassis/body are considered as separate problems. The truth is that a lot of trade-offs can be made between these systems, causing an overall improvement in many areas including total cost. Motor controller and battery cost have a relatively simple relationship; the less energy lost in the motor controller the less energy that has to be carried in the batteries, hence the lower the battery cost. A motor controller’s cost is primarily influenced by the cost of the switches. This paper will therefore present a method of assessing the optimal switch selection on the premise that the optimal switch is the one that produces the lowest system cost, where system cost is the cost of batteries + switches.

An activity and resource advisory system for manufacturing process chains selection at the early stage of product development

Designers need to consider both the functional and production process requirements at the early stage of product development. A variety of the research works found in the literature has been proposed to assist designers in selecting the most viable manufacturing process chain. However, they do not provide any assistance for designers to evaluate the processes according to the particular circumstances of their company. This paper describes a framework of an Activity and Resource Advisory System (ARAS) that generates advice about the required activities and the possible resources for various manufacturing process chains. The system provides more insight, more flexibility, and a more holistic and suitable approach for designers to evaluate and then select the most viable manufacturing process chain at the early stage of product development.

Microalgal species selection for biodiesel production based on fuel properties derived from fatty acid profiles

Physical and chemical properties of biodiesel are influenced by structural features of the fatty acids, such as chain length, degree of unsaturation and branching of the carbon chain. This study investigated if microalgal fatty acid profiles are suitable for biodiesel characterization and species selection through Preference Ranking Organisation Method for Enrichment Evaluation (PROMETHEE) and Graphical Analysis for Interactive Assistance (GAIA) analysis. Fatty acid methyl ester (FAME) profiles were used to calculate the likely key chemical and physical properties of the biodiesel [cetane number (CN), iodine value (IV), cold filter plugging point, density, kinematic viscosity, higher heating value] of nine microalgal species (this study) and twelve species from the literature, selected for their suitability for cultivation in subtropical climates. An equal-parameter weighted (PROMETHEE-GAIA) ranked Nannochloropsis oculata, Extubocellulus sp. and Biddulphia sp. highest; the only species meeting the EN14214 and ASTM D6751-02 biodiesel standards, except for the double bond limit in the EN14214. Chlorella vulgaris outranked N. oculata when the twelve microalgae were included. Culture growth phase (stationary) and, to a lesser extent, nutrient provision affected CN and IV values of N. oculata due to lower eicosapentaenoic acid (EPA) contents. Application of a polyunsaturated fatty acid (PUFA) weighting to saturation led to a lower ranking of species exceeding the double bond EN14214 thresholds. In summary, CN, IV, C18:3 and double bond limits were the strongest drivers in equal biodiesel parameter-weighted PROMETHEE analysis.

The structured and practical approach in development of decision support system for consultant selection in public sector infrastructure project

Nowadays, most of the infrastructure development projects undertaken are complex in nature. Practically, public clients who do not have a good understanding of the design and management may suffer severe losses, especially for infrastructure projects. There is a need for luring the right consultant to secure client's investment in infrastructure developments. Throughout the project life cycle, consultants play vital role from the inception to completion stage of a project. A few studies in Malaysia show that infrastructure projects involving irrigation and drainage have experience problems such as poor workmanship, delay and cost overrun due to the consultant's inability or the client incompetence of recruiting consultants in time. This highlights the need of aided decision making and an efficient system to select the best consultant by using Decision Support System (DSS). On the other hand, recent trends reveal that most DSS in construction only concentrate on decision model development. These models are impractical and unused as they are complicated or difficult for laymen such as project managers to utilize. Thus, this research attempts to develop an efficient DSS for consultant selection namely consultDeSS. Driven by the motivation and research aims, this study deployed Design Science Research Methodology (DSRM) dominant with a combination of case studies at the Malaysian Department of Irrigation and Drainage (DID). Two real projects involving irrigation and drainage infrastructure were used to design, implement and evaluate the artefact. The 3-tier consultDeSS was revised after the evaluation and the design was significantly improved based on user feedback. By developing desirable tools that fit client's needs will enhance the productivity and minimize conflict within groups and organisations. The tool is more usable and efficient compared to previous studies in construction. Thus, this research has demonstrated a purposeful artefact with a practical and valid structured development approach that is applicable in a variety of problems in construction discipline.

An evaluation of dog-assisted therapy for residents of aged care facilities with dementia.

Although some research suggests that dog-assisted therapy may be beneficial for people with dementia living in residential aged care facilities, the intervention has not been adequately investigated. To address this shortcoming, we conducted a randomized controlled trial of dog-assisted therapy versus a human-therapist-only intervention for this population. Fifty-five residents with mild to moderate dementia living in three Australian residential aged care facilities completed an 11-week trial of the interventions. Allocation to the intervention was random and participants completed validated measures of mood, psychosocial functioning, and quality of life (QOL), both prior to and following the intervention. No adverse events were associated with the dog-assisted intervention, and following it participants who had worse baseline depression scores demonstrated significantly improved depression scores relative to participants in the human-therapist-only intervention. Participants in the dogassisted intervention also showed significant improvements on a measure of QOL in one facility compared with those in the human-therapist-only group (although worse in another facility that had been affected by an outbreak of gastroenteritis). This study provides some evidence that dog-assisted therapy may be beneficial for some residents of aged care facilities with dementia.

The role of the molecular footprint of EGFR in tailoring treatment decisions in NSCLC

The majority of patients with non-small-cell lung cancer (NSCLC) present with advanced disease, with targeted therapies providing some improvement in clinical outcomes. The epidermal growth factor receptor (EGFR) tyrosine kinase (TK) plays an important role in the pathogenesis of NSCLC. Tyrosine kinase inhibitors (TKIs), which target the EGFR TK domain, have proven to be an effective treatment strategy; however, patient responses to treatment vary considerably. Therefore, the identification of patients most likely to respond to treatment is essential to optimise the benefit of TKIs. Tumour-associated activating mutations in EGFR can identify patients with NSCLC who are likely to have a good response to TKIs. Nonetheless, the majority of patients relapse within a year of starting treatment. Studies of tumours at relapse have demonstrated expression of a T790M mutation in exon 20 of the EGFR TK domain in approximately 50% of cases. Although conferring resistance to reversible TKIs, these patients may remain sensitive to new-generation irreversible/panerb inhibitors. A number of techniques have been employed for genotypic assessment of tumourassociated DNA to identify EGFR mutations, each of which has advantages and disadvantages. This review presents an overview of the current methodologies used to identify such molecular markers. Recent developments in technology may make the monitoring of changes in patients' tumour genotypes easier in clinical practice, which may enable patients' treatment regimens to be tailored during the course of their disease, potentially leading to improved patient outcomes.