Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Direct and indirect effects on households’ intentions to replace the old car

With the purpose of testing the hypothesis that households’ intentions to replace their old car have a direct negative relationship to its perceived quality (‘current level’) and a direct positive relationship to their aspirations for a new car (‘aspiration level’), a rotating panel of car owners were interviewed every fourth month during 2 years. In this data set the hypothesis received support. In addition the results showed that the age of the car, the total number of miles driven, and the number of anticipated repairs affected the current level, whereas marital status, the number of children, consumer confidence, and environmental concern affected the aspiration level.

The growth-profitability relationship : strategic orientations as moderator

Principal Topic: In this study we investigate how strategic orientation moderates the impact of growth on profitability for a sample of Danish high growth (Gazelle) firms. ---------- Firm growth has been an essential part of both management research and entrepreneurship research for decades (e.g. Penrose 1959, Birch 1987, Storey 1994). From a societal point of view, firm growth has been perceived as economic generator and job creator. In entrepreneurship research, growth has been an important part of the field (Davidsson, Delmar and Wiklund 2006), and many have used growth as a measure of success. In strategic management, growth has been seen as an approach to achieve competitive advantages and a way of becoming increasing profitable (e.g. Russo and Fouts 1997, Cho and Pucic 2005). However, although firm growth used to be perceived as a natural pathway to profitability recently more skepticism has emerged due to both new theoretical development and new empirical insights. Empirically, studies show inconsistent and inconclusive empirical evidence regarding the impact of growth on profitability. Our review reveals that some studies find a substantial positive relationship, some find a weak positive relationship, some find no relationship and further some find a negative relationship. Overall, two dominant yet divergent theoretical positions can be identified. The first position, mainly focusing on the environmental fit, argues that firms are likely to become more profitable if they enter a market quickly and on a larger scale due to first mover advantages and economic of scale. The second position, mainly focusing the internal fit, argues that growth may lead to a range of internal challenges and difficulties, including rapid change in structure, reward systems, decision making, communication and management style. The inconsistent empirical results together with two divergent theoretical positions call for further investigations into the circumstances by which growth generate profitability and into the circumstances by which growth do not generate profitability. In this project, we investigate how strategic orientations influence the impact of growth on profitability by asking the following research question: How is the impact of growth on profitability moderated by strategic orientation? Based on a literature review of how growth impacts profitability in areas such as entrepreneurship, strategic management and strategic entrepreneurship we develop three hypotheses regarding the growth-profitability relationship and strategic orientation as a potential moderator. ---------- Methodology/Key Propositions: The three hypotheses are tested on data collected in 2008. All firms in Denmark, including all listed and non-listed (VAT-registered) firms who experienced a 100 % growth and had a positive sales or gross profit over a four years period (2004-2007) were surveyed. In total 2,475 fulfilled the requirements. Among those 1,107 firms returned usable questionnaires satisfactory giving us a response rate on 45 %. The financial data together with data on number of employees were obtained from D&B (previously Dun & Bradstreet). The remaining data were obtained through the survey. Hierarchical regression models with ROA (return on assets) as the dependent variable were used to test the hypotheses. In the first model control variables including region, industry, firm age, CEO age, CEO gender, CEO education and number of employees were entered. In the second model, growth measured as growth in employees was entered. Then strategic orientation (differentiation, cost leadership, focus differentiation and focus cost leadership) and then interaction effects of strategic orientation and growth were entered in the model. ---------- Results and Implications: The results show a positive impact of firm growth on profitability and further that this impact is moderated by strategic orientation. Specifically, it was found that growth has a larger impact on profitability when firms do not pursue a focus strategy including both focus differentiation and focus cost leadership. Our preliminary interpretation of the results suggests that the value of growth depends on the circumstances and more specifically 'how much is left to fight for'. It seems like those firms who target towards a narrow segment are less likely to gain value of growth. The remaining market shares to fight for to these firms are not large enough to compensate for the cost of growing. Based on our findings, it therefore seems like growth has a more positive relationship with profitability for those who approach a broad market segment. Furthermore we argue that firms pursuing af Focus strategy will have more specialized assets that decreases the possibilities of further profitable expansion. For firms, CEOs, board of directors etc., the study shows that high growth is not necessarily something worth aiming for. It is a trade-off between the cost of growing and the value of growing. For many firms, there might be better ways of generating profitability in the long run. It depends on the strategic orientation of the firm. For advisors and consultants, the conditional value of growth implies that in-depth knowledge on their clients' situation is necessary before any advice can be given. And finally, for policy makers, it means they have to be careful when initiating new policies to promote firm growth. They need to take into consideration firm strategy and industry conditions.

Virtual Environment Visualisation of Executable Business Process Models

Business Process Modelling is a fast growing field in business and information technology, which uses visual grammars to model and execute the processes within an organisation. However, many analysts present such models in a 2D static and iconic manner that is difficult to understand by many stakeholders. Difficulties in understanding such grammars can impede the improvement of processes within an enterprise due to communication problems. In this chapter we present a novel framework for intuitively visualising animated business process models in interactive Virtual Environments. We also show that virtual environment visualisations can be performed with present 2D business process modelling technology, thus providing a low barrier to entry for business process practitioners. Two case studies are presented from film production and healthcare domains that illustrate the ease with which these visualisations can be created. This approach can be generalised to other executable workflow systems, for any application domain being modelled.

Estimating short and long-term residential demand for electricity : new evidence from Sri Lanka

This study investigates the short-run dynamics and long-run equilibrium relationship between residential electricity demand and factors influencing demand - per capita income, price of electricity, price of kerosene oil and price of liquefied petroleum gas - using annual data for Sri Lanka for the period, 1960-2007. The study uses unit root, cointegration and error-correction models. The long-run demand elasticities of income, own price and price of kerosene oil (substitute) were estimated to be 0.78, - 0.62, and 0.14 respectively. The short-run elasticities for the same variables were estimated to be 032, - 0.16 and 0.10 respectively. Liquefied petroleum (LP) gas is a substitute for electricity only in the short-run with an elasticity 0.09. The main findings of the paper support the following (1) increasing the price of electricity is not the most effective tool to reduce electricity consumption (2) existing subsidies on electricity consumption can be removed without reducing government revenue (3) the long-run income elasticity of demand shows that any future increase in household incomes is likely to significantly increase the demand for electricity and(4) any power generation plans which consider only current per capita consumption and population growth should be revised taking into account the potential future income increases in order to avoid power shortages ill the country.

Mapping a suburb with a single camera using a biologically inspired SLAM system

This paper describes a biologically inspired approach to vision-only simultaneous localization and mapping (SLAM) on ground-based platforms. The core SLAM system, dubbed RatSLAM, is based on computational models of the rodent hippocampus, and is coupled with a lightweight vision system that provides odometry and appearance information. RatSLAM builds a map in an online manner, driving loop closure and relocalization through sequences of familiar visual scenes. Visual ambiguity is managed by maintaining multiple competing vehicle pose estimates, while cumulative errors in odometry are corrected after loop closure by a map correction algorithm. We demonstrate the mapping performance of the system on a 66 km car journey through a complex suburban road network. Using only a web camera operating at 10 Hz, RatSLAM generates a coherent map of the entire environment at real-time speed, correctly closing more than 51 loops of up to 5 km in length.

Hippocampal models for simultaneous localisation and mapping on an autonomous robot

To navigate successfully in a novel environment a robot needs to be able to Simultaneously Localize And Map (SLAM) its surroundings. The most successful solutions to this problem so far have involved probabilistic algorithms, but there has been much promising work involving systems based on the workings of part of the rodent brain known as the hippocampus. In this paper we present a biologically plausible system called RatSLAM that uses competitive attractor networks to carry out SLAM in a probabilistic manner. The system can effectively perform parameter self-calibration and SLAM in one dimension. Tests in two dimensional environments revealed the inability of the RatSLAM system to maintain multiple pose hypotheses in the face of ambiguous visual input. These results support recent rat experimentation that suggest current competitive attractor models are not a complete solution to the hippocampal modelling problem.

Secondary curve behaviour in Lenke IC class adolescent idiopathic scoliosis following video assisted thoracoscopic spinal fusion

Introduction. Ideally after selective thoracic fusion for Lenke Class IC (i.e. major thoracic / secondary lumbar) curves, the lumbar spine will spontaneously accommodate to the corrected position of the thoracic curve, thereby achieving a balanced spine, avoiding the need for fusion of lumbar spinal segments1. The purpose of this study was to evaluate the behaviour of the lumbar curve in Lenke IC class adolescent idiopathic scoliosis (AIS) following video-assisted thoracoscopic spinal fusion and instrumentation (VATS) of the major thoracic curve. Methods. A retrospective review of 22 consecutive patients with AIS who underwent VATS by a single surgeon was conducted. The results were compared to published literature examining the behaviour of the secondary lumbar curve where other surgical approaches were employed. Results. Twenty-two patients (all female) with AIS underwent VATS. All major thoracic curves were right convex. The average age at surgery was 14 years (range 10 to 22 years). On average 6.7 levels (6 to 8) were instrumented. The mean follow-up was 25.1 months (6 to 36). The pre-operative major thoracic Cobb angle mean was 53.8° (40° to 75°). The pre-operative secondary lumbar Cobb angle mean was 43.9° (34° to 55°). On bending radiographs, the secondary curve corrected to 11.3° (0° to 35°). The rib hump mean measurement was 15.0° (7° to 21°). At latest follow-up the major thoracic Cobb angle measured on average 27.2° (20° to 41°) (p<0.001 – univariate ANOVA) and the mean secondary lumbar curve was 27.3° (15° to 42°) (p<0.001). This represented an uninstrumented secondary curve correction factor of 37.8%. The mean rib hump measured was 6.5° (2° to 15°) (p<0.001). The results above were comparable to published series when open surgery was performed. Discussion. VATS is an effective method of correcting major thoracic curves with secondary lumbar curves. The behaviour of the secondary lumbar curve is consistent with published series when open surgery, both anterior and posterior, is performed.

Lip detection for audio-visual speech recognition in-car environment

Acoustically, car cabins are extremely noisy and as a consequence audio-only, in-car voice recognition systems perform poorly. As the visual modality is immune to acoustic noise, using the visual lip information from the driver is seen as a viable strategy in circumventing this problem by using audio visual automatic speech recognition (AVASR). However, implementing AVASR requires a system being able to accurately locate and track the drivers face and lip area in real-time. In this paper we present such an approach using the Viola-Jones algorithm. Using the AVICAR [1] in-car database, we show that the Viola- Jones approach is a suitable method of locating and tracking the driver’s lips despite the visual variability of illumination and head pose for audio-visual speech recognition system.

Social Participation of Community Dwelling Stroke Survivors [Published Abstract: From the Quality of Care and Outcomes Research in Cardiovascular Disease and Stroke Conference 2009]

Disability following a stroke can impose various restrictions on patients’ attempts at participating in life roles. The measurement of social participation, for instance, is important in estimating recovery and assessing quality of care at the community level. Thus, the identification of factors influencing social participation is essential in developing effective measures for promoting the reintegration of stroke survivors into the community. Data were collected from 188 stroke survivors (mean age 71.7 years) 12 months after discharge from a stroke rehabilitation hospital. Of these survivors, 128 (61 %) had suffered a first ever stroke, and 81 (43 %) had a right hemisphere lesion. Most (n = 156, 83 %) were living in their own home, though 32 (17 %) were living in residential care facilities. Path analysis was used to test a hypothesized model of participation restriction which included the direct and indirect effects between social, psychological and physical outcomes and demographic variables. Participation restriction was the dependent variable. Exogenous independent variables were age, functional ability, living arrangement and gender. Endogenous independent variables were depressive symptoms, state self-esteem and social support satisfaction. The path coefficients showed functional ability having the largest direct effect on participation restriction. The results also showed that more depressive symptoms, low state self-esteem, female gender, older age and living in a residential care facility had a direct effect on participation restriction. The explanatory variables accounted for 71% of the variance in explaining participation restriction. Prediction models have empirical and practical applications such as suggesting important factors to be considered in promoting stroke recovery. The findings suggest that interventions offered over the course of rehabilitation should be aimed at improving functional ability and promoting psychological aspects of recovery. These are likely to enhance stroke survivors resume or maximize their social participation so that they may fulfill productive and positive life roles.

The rediscovery of traditional urbanism at Melrose Arch

Contemporary urban form, particularly in the cities of South Africa, lacks distinction and quality. The majority of developments are conceived as private and dislocated initiatives, surveiled enclaves with gated access being the only conduit to the outside world. Any concern for a positive contribution to the matrix of public activity is seldom a consideration. The urban form responds to the perception that traffic systems are paramount to the successful flux of the city in satisfying the escalating demands of vehicular movement. In contrast many of the urban centres around the world, the great historical centres of Europe, Americas and the Sub-Continent are admired and considered the ultimate models in urban experience. The colonnades, bazaars and boulevards hosting an abundance of street activity are the characteristics of such centres and are symptomatic of a city growth based on pedestrian movement patterns, an urbanism supportative of human interaction and exchange, a form which has nurtured the existence of a public realm. Through the understanding of the principles of traditional urbanism we may learn that the modernist paradigm of a contemporary suburbia has resulted in disconnected and separate land uses with isolated districts where a reliance on the car is essential rather than optional.

Bayesian hybrid algorithms and models : implementation and associated issues

This thesis addresses computational challenges arising from Bayesian analysis of complex real-world problems. Many of the models and algorithms designed for such analysis are ‘hybrid’ in nature, in that they are a composition of components for which their individual properties may be easily described but the performance of the model or algorithm as a whole is less well understood. The aim of this research project is to after a better understanding of the performance of hybrid models and algorithms. The goal of this thesis is to analyse the computational aspects of hybrid models and hybrid algorithms in the Bayesian context. The first objective of the research focuses on computational aspects of hybrid models, notably a continuous finite mixture of t-distributions. In the mixture model, an inference of interest is the number of components, as this may relate to both the quality of model fit to data and the computational workload. The analysis of t-mixtures using Markov chain Monte Carlo (MCMC) is described and the model is compared to the Normal case based on the goodness of fit. Through simulation studies, it is demonstrated that the t-mixture model can be more flexible and more parsimonious in terms of number of components, particularly for skewed and heavytailed data. The study also reveals important computational issues associated with the use of t-mixtures, which have not been adequately considered in the literature. The second objective of the research focuses on computational aspects of hybrid algorithms for Bayesian analysis. Two approaches will be considered: a formal comparison of the performance of a range of hybrid algorithms and a theoretical investigation of the performance of one of these algorithms in high dimensions. For the first approach, the delayed rejection algorithm, the pinball sampler, the Metropolis adjusted Langevin algorithm, and the hybrid version of the population Monte Carlo (PMC) algorithm are selected as a set of examples of hybrid algorithms. Statistical literature shows how statistical efficiency is often the only criteria for an efficient algorithm. In this thesis the algorithms are also considered and compared from a more practical perspective. This extends to the study of how individual algorithms contribute to the overall efficiency of hybrid algorithms, and highlights weaknesses that may be introduced by the combination process of these components in a single algorithm. The second approach to considering computational aspects of hybrid algorithms involves an investigation of the performance of the PMC in high dimensions. It is well known that as a model becomes more complex, computation may become increasingly difficult in real time. In particular the importance sampling based algorithms, including the PMC, are known to be unstable in high dimensions. This thesis examines the PMC algorithm in a simplified setting, a single step of the general sampling, and explores a fundamental problem that occurs in applying importance sampling to a high-dimensional problem. The precision of the computed estimate from the simplified setting is measured by the asymptotic variance of the estimate under conditions on the importance function. Additionally, the exponential growth of the asymptotic variance with the dimension is demonstrated and we illustrates that the optimal covariance matrix for the importance function can be estimated in a special case.

Next Generation ‘Filmmaking’: New Markets, New Methods and New Business Models

Digital production and distribution technologies may create new opportunities for filmmaking in Australia. A culture of new approaches to filmmaking is emerging driven by ‘next generation filmmakers’ who are willing to consider new business models: from online web series to short films produced for mobile phones. At the same time cultural representation itself is transforming within an interactive, social media driven environment. Yet there is very little research into next generation filmmaking. The aim of this paper is to scope and discuss three key aspects of next generation filmmaking, namely: digital trends in film distribution and marketing; processes and strategies of ‘next generation’ filmmakers; and case studies of viable next generation business models and filmmaking practices. We conclude with a brief examination of the implications for media and cultural policy which suggests the future possibility of a rapprochement between creative industries discourse and cultural policy.

Incorporating uncertainty in environmental models informed by imagery

In this thesis, the issue of incorporating uncertainty for environmental modelling informed by imagery is explored by considering uncertainty in deterministic modelling, measurement uncertainty and uncertainty in image composition. Incorporating uncertainty in deterministic modelling is extended for use with imagery using the Bayesian melding approach. In the application presented, slope steepness is shown to be the main contributor to total uncertainty in the Revised Universal Soil Loss Equation. A spatial sampling procedure is also proposed to assist in implementing Bayesian melding given the increased data size with models informed by imagery. Measurement error models are another approach to incorporating uncertainty when data is informed by imagery. These models for measurement uncertainty, considered in a Bayesian conditional independence framework, are applied to ecological data generated from imagery. The models are shown to be appropriate and useful in certain situations. Measurement uncertainty is also considered in the context of change detection when two images are not co-registered. An approach for detecting change in two successive images is proposed that is not affected by registration. The procedure uses the Kolmogorov-Smirnov test on homogeneous segments of an image to detect change, with the homogeneous segments determined using a Bayesian mixture model of pixel values. Using the mixture model to segment an image also allows for uncertainty in the composition of an image. This thesis concludes by comparing several different Bayesian image segmentation approaches that allow for uncertainty regarding the allocation of pixels to different ground components. Each segmentation approach is applied to a data set of chlorophyll values and shown to have different benefits and drawbacks depending on the aims of the analysis.