Effects of dry density and grain size distribution on soil-water characteristic curves of sandy soils

The unsaturated soil mechanics is receiving increasing attention from researchers and as well as from practicing engineers. However, the requirement of sophisticated devices to measure unsaturated soil properties and time consumption have made the geotechnical engineers keep away from implication of the unsaturated soil mechanics for solving practical geotechnical problems. The application of the conventional laboratory devices with some modifications to measure unsaturated soil properties can promote the application of unsaturated soil mechanics into engineering practice. Therefore, in the present study, a conventional direct shear device was modified to measure unsaturated shear strength parameters at low suction. Specially, for the analysis of rain-induced slope failures, it is important to measure unsaturated shear strength parameters at low suction where slopes become unstable. The modified device was used to measure unsaturated shear strength of two silty soils at low suction values (0 ~ 50 kPa) that were achieved by following drying path and wetting path of soil-water characteristic curves (SWCCs) of soils. The results revealed that the internal friction angle of soil was not significantly affected by the suction and as well as the drying-wetting SWCCs of soils. The apparent cohesion of soil increased with a decreasing rate as the suction increased. Further, the apparent cohesion obtained from soil in wetting was greater than that obtained from soil in drying. Shear stress-shear displacement curves obtained from soil specimens subjected to the same net normal stress and different suction values showed a higher initial stiffness and a greater peak stress as the suction increased. In addition, it was observed that soil became more dilative with the increase of suction. A soil in wetting exhibited slightly higher peak shear stress and more contractive volume change behaviour than that of in drying at the same net normal stress and the suction.

Investigation on parameters used in warning systems for rain-induced embankment instability

A number of instrumented laboratory-scale soil embankment slopes were subjected to artificial rainfall until they failed. The factor of safety of the slope based on real-time measurements of pore-water pressure (suction) and laboratory measured soil properties were calculated as the rainfall progressed. Based on the experiment measurements and slope stability analysis, it was observed that slope displacement measurements can be used to warn the slope failure more accurately. Further, moisture content/pore-water pressure measurements near the toe of the slope and the real-time factor of safety can also be used for prediction of rainfall-induced embankment failures with adequate accuracy.

Optimism about safety and group-serving interpretations of safety among pedestrians and cyclists in relation to road use in general and under low light conditions

Drivers are known to be optimistic about their risk of crash involvement, believing that they are less likely to be involved in a crash than other drivers. However, little comparative research has been conducted among other road users. In addition, optimism about crash risk is conceptualised as applying only to an individual’s assessment of his or her personal risk of crash involvement. The possibility that the self-serving nature of optimism about safety might be generalised to the group-level as a cyclist or a pedestrian, i.e., becoming group-serving rather than self-serving, has been overlooked in relation to road safety. This study analysed a subset of data collected as part of a larger research project on the visibility of pedestrians, cyclists and road workers, focusing on a set of questionnaire items administered to 406 pedestrians, 838 cyclists and 622 drivers. The items related to safety in various scenarios involving drivers, pedestrians and cyclists, allowing predictions to be derived about group differences in agreement with items based on the assumption that the results would exhibit group-serving bias. Analysis of the responses indicated that specific hypotheses about group-serving interpretations of safety and responsibility were supported in 22 of the 26 comparisons. When the nine comparisons relevant to low lighting conditions were considered separately, seven were found to be supported. The findings of the research have implications for public education and for the likely acceptance of messages which are inconsistent with current assumptions and expectations of pedestrians and cyclists. They also suggest that research into group-serving interpretations of safety, even for temporary roles rather than enduring groups, could be fruitful. Further, there is an implication that gains in safety can be made by better educating road users about the limitations of their visibility and the ramifications of this for their own road safety, particularly in low light.

Safety in occupational driving : development of a driver behaviour scale for the workplace context

International statistics indicate that occupational, or work-related driving, crashes are the most common cause of workplace injury, death, and absence from work. The majority of research examining unsafe driver behavior in the workplace has relied on general road safety questionnaires. However, past research has failed to consider the organizational context in the use of these questionnaires, and as such, there is ambiguity in the dimensions constituting occupational driving. Using a theoretical model developed by Hockey (1993, 1997), this article proposes and validates a new scale of occupational driver behavior. This scale incorporates four dimensions of driver behavior that are influenced by demanding workplace conditions; speeding, rule violation, inattention, and driving while tired. Following a content validation process, three samples of occupational drivers in Australia were used to assess the scale. Data from the first sample (n=145) were used to reduce the number of scale items and provide an assessment of the factorial validity of the scale. Data from the second sample (n=645) were then used to confirm the factor structure and psychometric properties of the scale including reliability and construct validity. Finally, data from the third sample (n=248) were used to establish criterion validity. The results indicated that the scale is a reliable and valid measure of occupational driver behavior.

The influence of safety ownership on occupational road safety outcomes

Questionnaires and interviews were conducted with employees and senior managers from three Australian organisations to explore the relationship between perceived managerial ownership of safety responsibilities and occupational road safety. It was found that the perceived authority of the person primarily responsible for managing road risks and perceived shared ownership of safety tasks were both significant independent predictors of safer driving behaviours. It was identified that the position of the person accepting primary risk management responsibilities was typically a member of the OHS team and typically in a management position. The extent that ownership was shared across members within the researched organisations varied, with personnel from OHS and fleet management typically accepting partial ownership of managing occupational road risks. Based on the findings, several recommendations are made to assist practitioners in managing occupational road risks.

Use of ITS to improve level crossings safety : open issues

Level crossing crashes have been shown to result in enormous human and financial cost to society. According to the Australian Transport Safety Bureau (ATSB) [5] a total of 632 Railway Level crossing (RLX) collisions, between trains and road vehicles, occurred in Australia between 2001 and June 2009. The cost of RLX collisions runs into the tens of millions of dollars each year in Australia [6]. In addition, loss of life and injury are commonplace in instances where collisions occur. Based on estimates that 40% of rail related fatalities occur at level crossings [12], it is estimated that 142 deaths between 2001 and June 2009 occurred at RLX. The aim of this paper is to (i) summarise crash patterns in Australia, (ii) review existing international ITS interventions to improve level crossing and (iii) highlights open human factors research related issues. Human factors (e.g., driver error, lapses or violations) have been evidenced as a significant contributing factor in RLX collisions, with drivers of road vehicles particularly responsible for many collisions. Unintentional errors have been found to contribute to 46% of RLX collisions [6] and appear to be far more commonplace than deliberate violations. Humans have been found to be inherently inadequate at using the sensory information available to them to facilitate safe decision-making at RLX and tend to underestimate the speed of approaching large objects due to the non-linear increases in perceived size [6]. Collisions resulting from misjudgements of train approach speed and distance are common [20]. Thus, a fundamental goal for improved RLX safety is the provision of sufficient contextual information to road vehicle drivers to facilitate safe decision-making regarding crossing behaviours.

Investigating challenges and opportunities of water sensitive urban design for knowledge based development of Australian cities

A new approach that is slowly replacing neoclassical models of economic growth and commodity based industrial activities, knowledge based urban development (KBUD) aims to provide opportunities for citiesw to foster knowledge creation, exchange and innovation, and is based on the concepts of both sustainable urban development and economic prosperity; sustainable uses and protection of natural resources are therefore integral parts of KBUD. As such, stormwater, which has been recognised as one of the main culprits of aquatic ecosystem pollution and as therefore a significant threat to the goal of sustainable urban development, needs to be managed in a manner that produces ecologically sound outcomes. Water sensitive urban design (WSUD) is one of the key responses to the need to better management urban stormwater runoff and supports KBUD by providing an alternative, innovative and effective strategy to traditional stormwater management.

Older adults’ safety perceptions of driving situations: Towards a new driving self-regulation scale

The term ‘driving self-restriction’ is used in the road safety literature to describe the behaviour of some older drivers. It includes the notion that older drivers will avoid driving in specific, usually self-identified situations, such as those in which safety is compromised. We sought to identify the situations that older drivers report avoiding; and, to determine the adequacy of a key measure of such behaviour. A sample of 75 drivers aged 65 years and older completed Baldock et al.’s modification of the Driving Habits Questionnaire avoidance items (Baldock et al., 2006), the Driving Behaviour Questionnaire, and open-ended items that elicited written descriptions of the most and least safe driving situation. Consistent with previous results, we found a relatively low level of driving self-restriction and infrequent episodes of aggressive violations. However, when combined with the situation descriptions, these data suggest that Driving Habits Questionnaire did not cover all of the situations that older drivers might choose avoid. We suggest that a new avoidance scale is needed and we present a new item pool that may be used for this purpose.

Developing a motorcycle and scooter safety compendium for the Asia-Pacific Economic Cooperation (APEC)

Motorcycle and scooter crashes are significant contributors to road trauma in many low, medium and high income countries. The APEC Transportation Working Group has commissioned CARRS-Q to develop a compendium of best practice measures that can be used to reduce crashes, post-crash trauma and associated socio-economic costs. The compendium will be informed by findings from a literature review and an expert survey. The literature review examined motorcycle and scooter safety usage and fatalities along with socio-cultural factors which might influence safety in each economy. A discussion is provided regarding the processes involved in the expert survey and how this might be integrated with the findings from the literature review. The implications for developing the compendium are discussed as is the next step of a workshop to further disseminate findings. This will enable the identification of important motorcycle safety issues in APEC economies and implications for implementation of countermeasures.

Enhancing Water Sensitive Urban Design (WSUD) practices to mitigate urban stormwater pollution and reuse potential

Water Sensitive Urban Design (WSUD) practices such as wetlands, bioretention systems and swales are widely implemented in Australia’s urban areas for the mitigation of stormwater pollution and to enhance its reuse potential. In-depth research undertaken has confirmed that these systems do not always perform according to design expectations due to a diversity of reasons. To deliver anticipated benefits, it is critical that they are designed in conformity with catchment and rainfall characteristics and pollutant processes. This in turn entails an in-depth understanding of key pollutant processes. This paper presents the outcomes of extensive research investigations on pollutant characterisation and stormwater pollutant processes on urban catchment surfaces. Outcomes from the research studies revealed the complexities in physical and chemical characteristics of pollutants originating from urban catchments which are strongly influenced by rainfall and catchment characteristics. Based on the research outcomes, recommendations are provided to enhance stormwater treatment performance and to enhance its reuse potential.

Supervisory safety practices in the work-related driving context

Work-related driving crashes are the most common cause of work-related injury, death, and absence from work in Australia and overseas. Surprisingly however, limited attention has been given to initiatives designed to improve safety outcomes in the work-related driving setting. This research paper will present preliminary findings from a research project designed to examine the effects of increasing work-related driving safety discussions on the relationship between drivers and their supervisors and motivations to drive safely. The research project was conducted within a community nursing population, where 112 drivers were matched with 23 supervisors. To establish discussions between supervisors and drivers, safety sessions were conducted on a monthly basis with supervisors of the drivers. At these sessions, the researcher presented context specific, audio-based anti-speeding messages. Throughout the course of the intervention and following each of these safety sessions, supervisors were instructed to ensure that all drivers within their workgroup listened to each particular anti-speeding message at least once a fortnight. In addition to the message, supervisors were also encouraged to frequently promote the anti-speeding message through any contact they had with their drivers (i.e., face to face, email, SMS text, and/or paper based contact). Fortnightly discussions were subsequently held with drivers, whereby the researchers ascertained the number and type of discussions supervisors engaged in with their drivers. These discussions also assessed drivers’ perceptions of the group safety climate. In addition to the fortnightly discussion, drivers completed a daily speed reporting form which assessed the proportion of their driving day spent knowingly over the speed limit. As predicted, the results found that if supervisors reported a good safety climate prior to the intervention, increasing the number of safety discussions resulted in drivers reporting a high quality relationship (i.e., leader-member exchange) with their supervisor post intervention. In addition, if drivers reported a good safety climate, increasing the number of discussions resulted in increased motivation to drive safely post intervention. Motivations to drive safely prior to the intervention also predicted self-reported speeding over the subsequent three months of reporting. These results suggest safety discussions play an important role in improving the exchange between supervisors and their drivers and drivers’ subsequent motivation to drive safely and, in turn, self reported speeding.

Stage 1 of the Yueyang Urban Water System Project: Landscape planning and design of Wangjia River

Chinese landscape architects are largely focused on objective practical solutions to environmental problems. In the West, theoretical landscape knowledge is largely conceptual and abstract. This research debated how Australian ecological concepts could or should be transposed to Chinese landscapes. This project responded to severe water and soil pollution issues in the estuarine and riparian zones of rivers flowing into Dongting Lake, in Yueyang City, Hunan Province. This work proposed a range of waterfront design innovations that challenged the notion of corridor as habitat, filter, barrier and conduit in a Chinese riparian context.

Construction safety in the repair and maintenance sector

Statistics indicate that the percentage of fatal industrial accidents arising from repair, maintenance, minor alteration and addition (RMAA) works in Hong Kong was disturbingly high and was over 56% in 2006. This paper provides an initial report of a research project funded by the Research Grants Council (RGC) of the HKSAR to address this safety issue. The aim of this study is to scrutinize the causal relationship between safety climate and safety performance in the RMAA sector. It aims to evaluate the safety climate in the RMAA sector; examine its impacts on safety performance, and recommend measures to improve safety performance in the RMAA sector. This paper firstly reports on the statistics of construction accidents arising from RMAA works. Qualitative and quantitative research methods applied in conducting the research are dis-cussed. The study will critically review these related problems and provide recommendations for improving safety performance in the RMAA sector.

A construction safety competency framework : development, industry application, and future benefits

View from the Construction sector as to the need to improve OHS culture What were the goals and the outcomes of the CRC Construction Innovation research Leadership behaviours to drive OHS culture change in industry What benefits to the construction sector have occurred through these initiatives What we have learnt on the journey

Empirical Bayes method in the study of traffic safety via heterogeneous negative multinomial model

In the study of traffic safety, expected crash frequencies across sites are generally estimated via the negative binomial model, assuming time invariant safety. Since the time invariant safety assumption may be invalid, Hauer (1997) proposed a modified empirical Bayes (EB) method. Despite the modification, no attempts have been made to examine the generalisable form of the marginal distribution resulting from the modified EB framework. Because the hyper-parameters needed to apply the modified EB method are not readily available, an assessment is lacking on how accurately the modified EB method estimates safety in the presence of the time variant safety and regression-to-the-mean (RTM) effects. This study derives the closed form marginal distribution, and reveals that the marginal distribution in the modified EB method is equivalent to the negative multinomial (NM) distribution, which is essentially the same as the likelihood function used in the random effects Poisson model. As a result, this study shows that the gamma posterior distribution from the multivariate Poisson-gamma mixture can be estimated using the NM model or the random effects Poisson model. This study also shows that the estimation errors from the modified EB method are systematically smaller than those from the comparison group method by simultaneously accounting for the RTM and time variant safety effects. Hence, the modified EB method via the NM model is a generalisable method for estimating safety in the presence of the time variant safety and the RTM effects.