Bio-hydrogen production from food waste through anaerobic fermentation

In order to protect our planet and ourselves from the adverse effects of excessive CO2 emissions and to prevent an imminent non-renewable fossil fuel shortage and energy crisis, there is a need to transform our current ‘fossil fuel dependent’ energy systems to new, clean, renewable energy sources. The world has recognized hydrogen as an energy carrier that complies with all the environmental quality and energy security, demands. This research aimed at producing hydrogen through anaerobic fermentation, using food waste as the substrate. Four food waste substrates were used: Rice, fish, vegetable and their mixture. Bio-hydrogen production was performed in lab scale reactors, using 250 mL serum bottles. The food waste was first mixed with the anaerobic sewage sludge and incubated at 37°C for 31 days (acclimatization). The anaerobic sewage sludge was then heat treated at 80°C for 15 min. The experiment was conducted at an initial pH of 5.5 and temperatures of 27, 35 and 55°C. The maximum cumulative hydrogen produced by rice, fish, vegetable and mixed food waste substrates were highest at 37°C (Rice =26.97±0.76 mL, fish = 89.70±1.25 mL, vegetable = 42.00±1.76 mL, mixed = 108.90±1.42 mL). A comparative study of acclimatized (the different food waste substrates were mixed with anaerobic sewage sludge and incubated at 37°C for 31days) and non-acclimatized food waste substrate (food waste that was not incubated with anaerobic sewage sludge) showed that acclimatized food waste substrate enhanced bio-hydrogen production by 90 - 100%.

Aerothermal-strucutral analysis of a rocket launched Mach 8 scramjet experiment : ascent

This paper reports on the methodology and results of a weak-coupled aerothermalstructural analysis on the ascent phase of the SCRAMSPACE Mach 8 scramjet flight experiment. This vehicle was essentially un-shrouded during the flight trajectory, relying on the thin, 5mm thick aluminium external shell of the payload to maintain structural integrity and protect the flight experiment. As such, understanding the thermal-structural response of the vehicle was imperative to mission success. Using two- and three-dimensional models, an iterative procedure was employed to compute the flowfield, convective heating, wall temperatures and structural coupling at flight times covering both peak heating and peak surface temperature. Accounting for such coupling resulted in a 150K reduction in wall temperature compared to the more conservative cold wall assumption. Despite this, peak temperatures remained of the order of 550 K. Further, thermally induced stresses within these regions were in excess of four times the material failure limits. Irreversible material failure during ascent was therefore concluded likely to occur on the external shell. Two alternate materials, steel 1006 and copper, were therefore assessed with the results indicating that steel sections on the external shell resulted in the best thermal-structural response of the payload.

Exploration of the fundamental equilibrium behaviour of calcium exchange with weak acid cation resins

This study evaluated the complexity of calcium ion exchange with sodium exchanged weak acid cation resin (DOW MAC-3). Exchange equilibria recorded for a range of different solution normalities revealed profiles which were represented by conventional “L” or “H” type isotherms at low values of equilibrium concentration (Ce) of calcium ions, plus a superimposed region of increasing calcium uptake was observed at high Ce values. The loading of calcium ions was determined to be ca. 53.5 to 58.7 g/kg of resin when modelling only the sorption curve created at low Ce values,which exhibited a well-defined plateau. The calculated calcium ion loading capacity for DOWMAC-3 resin appeared to correlate with the manufacturer's recommendation. The phenomenon of super equivalent ion exchange (SEIX) was observed when the “driving force” for the exchange process was increased in excess of 2.25 mmol calcium ions per gram of resin in the starting solution. This latter event was explained in terms of displacement of sodium ions from sodium hydroxide solution which remained in the resin bead following the initial conversion of the as supplied “H+” exchanged resin sites to the “Na+” version required for softening studies. Evidence for hydrolysis of a small fraction of the sites on the sodium exchanged resin surface was noted. The importance of carefully choosing experimental parameters was discussed especially in relation to application of the Langmuir–Vageler expression. This latter model which compared the ratio of the initial calcium ion concentration in solution to resin mass, versus final equilibrium loading of the calcium ions on the resin; was discovered to be an excellent means of identifying the progress of the calcium–sodium ion exchange process. Moreover, the Langmuir–Vageler model facilitated standardization of various calcium–sodium ion exchange experiments which allowed systematic experimental design.

Understanding carers' intention for their child to walk to school : further application of the theory of reasoned action

One quarter of Australian children are overweight or obese (ABS, 2010), putting them at increased risk of physical and psychological health problems (Reilly et al., 2003). Overweight and obesity in childhood tends to persist into adulthood and is associated with premature death and morbidity (Reilly & Kelly, 2011). Increases in Australian children’s weight have coincided with declines in active transportation, such as walking, to school (Salmon et al., 2005). Investigating the factors which influence walking to school is therefore important, particularly since walking to school is a low cost and effective means of reducing excess weight (Rosenberg et al., 2006) that can be easily integrated into daily routine (Brophy et al., 2011). While research in this area has expanded (e.g., Brophy et al., 2011; Giles-Corti et al., 2010), it is largely atheoretical (exceptions Napier et al., 2011). This is an important gap from a social marketing perspective given the use of theory lies at the foundation of the framework (NSMC, 2006) and a continued lack of theory use is observed (Luca & Suggs, 2013). The aim of this paper is to empirically examine a widely adopted theory, the deconstructed Theory of Reasoned Action (TRA) (Fishbein & Azjen, 1975), to understand the relative importance of attitude and subjective norms in determining intentions to increase walk to school behaviour.

A stakeholder process evaluation of a social marketing walking intervention targeting children

One quarter of Australian children are overweight or obese (ABS, 2010), putting them at increased risk of physical and psychological health problems (Reilly et al., 2003). Overweight and obesity in childhood tends to persist into adulthood and is associated with premature death and morbidity (Reilly & Kelly, 2011). Increases in Australian children’s weight have coincided with declines in active transportation, such as walking, to school (Salmon et al., 2005). To address this problem, the Victorian Health Promotion Foundation (VicHealth), which is an independent statutory authority which advises government and contributes to promoting good health in Victoria (VicHealth, 2014), developed the Walk to School program. Walk to School aims to encourage primary school children in Victoria to walk to and from school more often. Walking to school is a low cost and effective means of reducing excess weight (Rosenberg et al., 2006) that can be easily integrated into daily routine (Brophy et al., 2011). The purpose of this paper is to present the results of the stakeholder process evaluation of Walk to School 2013, which forms part of a broader outcome evaluation that is currently in field. Although there is an emphasis on outcome evaluation of programs, process evaluation can be equally important in determining program success (Saunders et al., 2005). Further, process evaluation to assess program delivery and utilization is explicitly recommended by two social marketing frameworks (see Lefebvre et al., 1988; Walsh et al., 1993).

Emerging from the shadows: Tax as a research discipline (Editorial)

More than ever, research is playing an important part in supporting proposed tax reforms and finding solutions to Australia’s tax system. Also, for tax academics the importance of quality research is critical in an increasingly competitive tertiary environment. However, life for an academic can be an isolating experience at time, especially if one’s expertise is in an area that many of their immediate colleagues do not share an interest in. Collegiately and the ability to be able to discuss research is seen as critical in fostering the next generation of academics. It is with this in mind that on the 5th of July 2010 the Inaugural Queensland Tax Teachers’ Symposium was hosted by Griffith University at its Southbank campus. The aim was to bring together for one day tax academics in Queensland, and further afield, to present their current research projects and encourage independent tax research. If was for this reason that the symposium was later re-named the Queensland Tax Researchers’ Symposium (QTRS) to reflect its emphasis. The Symposium has been held annually mid-year on four occasions with in excess of 120 attendees over this period. The fifth QTRS is planned for June 2014 to be hosted by James Cook University.

Frequency of convergence and accommodative disorders in a clinical population of Mashhad, Iran

Purpose To investigate the frequency of convergence and accommodation anomalies in an optometric clinical setting in Mashhad, Iran, and to determine tests with highest accuracy in diagnosing these anomalies. Methods From 261 patients who came to the optometric clinics of Mashhad University of Medical Sciences during a month, 83 of them were included in the study based on the inclusion criteria. Near point of convergence (NPC), near and distance heterophoria, monocular and binocular accommodative facility (MAF and BAF, respectively), lag of accommodation, positive and negative fusional vergences (PFV and NFV, respectively), AC/A ratio, relative accommodation, and amplitude of accommodation (AA) were measured to diagnose the convergence and accommodation anomalies. The results were also compared between symptomatic and asymptomatic patients. The accuracy of these tests was explored using sensitivity (S), specificity (Sp), and positive and negative likelihood ratios (LR+, LR−). Results Mean age of the patients was 21.3 ± 3.5 years and 14.5% of them had specific binocular and accommodative symptoms. Convergence and accommodative anomalies were found in 19.3% of the patients; accommodative excess (4.8%) and convergence insufficiency (3.6%) were the most common accommodative and convergence disorders, respectively. Symptomatic patients showed lower values for BAF (p = .003), MAF (p = .001), as well as AA (p = .001) compared with asymptomatic patients. Moreover, BAF (S = 75%, Sp = 62%) and MAF (S = 62%, Sp = 89%) were the most accurate tests for detecting accommodative and convergence disorders in terms of both sensitivity and specificity. Conclusions Convergence and accommodative anomalies are the most common binocular disorders in optometric patients. Including tests of monocular and binocular accommodative facility in routine eye examinations as accurate tests to diagnose these anomalies requires further investigation.

Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

The role of inflammation in cutaneous repair

Inflammation is a fundamental component of the normal adult wound healing response occurring even in the absence of infection. It performs many beneficial roles such as the clearing of damaged cells and extracellular matrix (ECM), the removal of pathogens that might other wise multiply and spread, and the secretion of mediators that regulate other aspects of wound healing such as proliferation, re-epithelialisation and wound remodelling. Yet, excess and/or prolonged inflammation is detrimental to wound healing and leads to increased fibrosis and scarring, which can be disfiguring and, in cases such as contractures, can lead to disability. Furthermore, excessive inflammation is a major contributing factor to the persistence of chronic non-healing wounds, which are “stuck” in the inflammatory phase of healing and fail to reepithelialise. Current research suggest that the type of immune cells, their timing and the level of inflammation in a wound could have dramatic effect on whether a wound heals in a timely fashion and the final quality of the repaired tissue. Studies suggest that altering the level of inflammation might be beneficial in terms of reducing scarring and improving the rate of healing in chronic wounds. This review looks at the role of the major immune cells in normal and impaired wound healing and strategies that might be used to reduce inflammation in wounds.

Weight-related risk perception among healthy and overweight pregnant women: A cross-sectional study

Objective The objective of this study was to evaluate weight-related risk perception in early pregnancy and to compare this perception between women commencing pregnancy healthy weight and overweight. Study design Pregnant women (n=664) aged 29±5 (mean±s.d.) years were recruited from a metropolitan teaching hospital in Australia. A self-administered questionnaire was completed at around 16 weeks of gestation. Height measured at baseline and self-reported pre-pregnancy weight were used to calculate body mass index. Cross-sectional analysis was conducted. Differences between groups were assessed using chi-squared tests for categorical variables and t-tests or Mann–Whitney U tests for continuous variables depending on distribution. Result Excess gestational weight gain (GWG) during pregnancy was more important in leading to health problems for women or their child compared with pre-pregnancy weight. Personal risk perception for complications was low for all women, although overweight women had slightly higher scores than healthy-weight women (2.4±1.0 vs 2.9±1.0; P<0.001). All women perceived their risk for complications to be below that of an average pregnant woman. Conclusion Women should be informed of the risk associated with their pre-pregnancy weight (in the case of maternal overweight) and excess GWG. If efforts to raise risk awareness are to result in preventative action, this information needs to be accompanied by advice and appropriate support on how to reduce risk.

In-situ carbon control in the preparation of precursors to boron carbide by a non-aqueous solution technique

Synthesis of high quality boron carbide (B4C) powders is achieved by carbothermal reduction of boron oxide (B2O3) from a condensed boric acid (H3BO3)/polyvinyl acetate (PVAc) product. Precursor solutions are prepared via free radical polymerisation of vinyl acetate (VA) monomer in methanol in the presence of dissolved H3BO3. A condensed product is then formed by flash evaporation under vacuum. As excess VA monomer is removed at the evaporation step, the polymerisation time is used to manage availability of carbon for reaction. This control of carbon facilitates dispersion of H3BO3 in solution due to the presence of residual VA monomer. B4C powders with very low residual carbon are formed at temperatures as low as 1,250 °C with a 4 hour residence time.

Turbulence and Mixing in the Environment: Multi-Device Study in a Sub-tropical Estuary

In an estuary, mixing and dispersion result from a combination of large-scale advection and smallscale turbulence, which are complex to estimate. The predictions of scalar transport and mixing are often inferred and rarely accurate, due to inadequate understanding of the contributions of these difference scales to estuarine recirculation. A multi-device field study was conducted in a small sub-tropical estuary under neap tide conditions with near-zero fresh water discharge for about 48 hours. During the study, acoustic Doppler velocimeters (ADV) were sampled at high frequency (50 Hz), while an acoustic Doppler current profiler (ADCP) and global positioning system (GPS) tracked drifters were used to obtain some lower frequency spatial distribution of the flow parameters within the estuary. The velocity measurements were complemented with some continuous measurement of water depth, conductivity, temperature and some other physiochemical parameters. Thorough quality control was carried out by implementation of relevant error removal filters on the individual data set to intercept spurious data. A triple decomposition (TD) technique was introduced to access the contributions of tides, resonance and ‘true’ turbulence in the flow field. The time series of mean flow measurements for both the ADCP and drifter were consistent with those of the mean ADV data when sampled within a similar spatial domain. The tidal scale fluctuation of velocity and water level were used to examine the response of the estuary to tidal inertial current. The channel exhibited a mixed type wave with a typical phase-lag between 0.035π– 0.116π. A striking feature of the ADV velocity data was the slow fluctuations, which exhibited large amplitudes of up to 50% of the tidal amplitude, particularly in slack waters. Such slow fluctuations were simultaneously observed in a number of physiochemical properties of the channel. The ensuing turbulence field showed some degree of anisotropy. For all ADV units, the horizontal turbulence ratio ranged between 0.4 and 0.9, and decreased towards the bed, while the vertical turbulence ratio was on average unity at z = 0.32 m and approximately 0.5 for the upper ADV (z = 0.55 m). The result of the statistical analysis suggested that the ebb phase turbulence field was dominated by eddies that evolved from ejection type process, while that of the flood phase contained mixed eddies with significant amount related to sweep type process. Over 65% of the skewness values fell within the range expected of a finite Gaussian distribution and the bulk of the excess kurtosis values (over 70%) fell within the range of -0.5 and +2. The TD technique described herein allowed the characterisation of a broader temporal scale of fluctuations of the high frequency data sampled within the durations of a few tidal cycles. The study provides characterisation of the ranges of fluctuation required for an accurate modelling of shallow water dispersion and mixing in a sub-tropical estuary.

Applying HYDRUS to flow in a sodic clay soil with solution composition–dependent hydraulic conductivity

Management of sodic soils under irrigation often requires application of chemical ameliorants to improve permeability combined with leaching of excess salts. Modeling irrigation, soil treatments, and leaching in these sodic soils requires a model that can adequately represent the physical and chemical changes in the soil associated with the amelioration process. While there are a number of models that simulate reactive solute transport, UNSATCHEM and HYDRUS-1D are currently the only models that also include an ability to simulate the impacts of soil chemistry on hydraulic conductivity. Previous researchers have successfully applied these models to simulate amelioration experiments on a sodic loam soil. To further gauge their applicability, we extended the previous work by comparing HYDRUS simulations of sodic soil amelioration with the results from recently published laboratory experiments on a more reactive, repacked sodic clay soil. The general trends observed in the laboratory experiments were able to be simulated using HYDRUS. Differences between measured and simulated results were attributed to the limited flexibility of the function that represents chemistry-dependent hydraulic conductivity in HYDRUS. While improvements in the function could be made, the present work indicates that HYDRUS-UNSATCHEM captures the key changes in soil hydraulic properties that occur during sodic clay soil amelioration and thus extends the findings of previous researchers studying sodic loams.

Effect of nitrification inhibitors (DMPP and 3MP+ TZ) on soil nitrous oxide emissions from a sub-tropical vegetable production system in Queensland, Australia

The use of nitrification inhibitors, in combination with ammonium based fertilisers, has been promoted recently as an effective method to reduce nitrous oxide (N2O) emissions from fertilised agricultural fields, whilst increasing yield and nitrogen use efficiency. Vegetable cropping systems are often characterised by high inputs of nitrogen fertiliser and consequently elevated emissions of nitrous oxide (N2O) can be expected. However, to date only limited data is available on the use of nitrification inhibitors in sub-tropical vegetable systems. A field experiment investigated the effect of the nitrification inhibitors (DMPP & 3MP+TZ) on N2O emissions and yield from a typical vegetable production system in sub-tropical Australia. Soil N2O fluxes were monitored continuously over an entire year with a fully automated system. Measurements were taken from three subplots for each treatment within a randomized complete blocks design. There was a significant inhibition effect of DMPP and 3MP+TZ on N2O emissions and soil mineral N content directly following the application of the fertiliser over the vegetable cropping phase. However this mitigation was offset by elevated N2O emissions from the inhibitor treatments over the post-harvest fallow period. Cumulative annual N2O emissions amounted to 1.22 kg-N/ha, 1.16 kg-N/ha, 1.50 kg-N/ha and 0.86 kg-N/ha in the conventional fertiliser (CONV), the DMPP treatment, the 3MP+TZ treatment and the zero fertiliser (0N) respectively. Corresponding fertiliser induced emission factors (EFs) were low with only 0.09 - 0.20% of the total applied fertiliser lost as N2O. There was no significant effect of the nitrification inhibitors on yield compared to the CONV treatment for the three vegetable crops (green beans, broccoli, lettuce) grown over the experimental period. This study highlights that N2O emissions from such vegetable cropping system are primarily controlled by post-harvest emissions following the incorporation of vegetable crop residues into the soil. It also shows that the use of nitrification inhibitors can lead to elevated N2O emissions by storing N in the soil profile that is available to soil microbes during the decomposition of the vegetable residues over the post-harvest phase. Hence the use of nitrification inhibitors in vegetable systems has to be treated carefully and fertiliser rates need to be adjusted to avoid excess soil nitrogen during the postharvest phase.

Sport across cultures: Applications of the human capital model in refugee communities

When working with the world’s most vulnerable populations there are questions surrounding the salience of physical activity promotion programs given the multitude of basic needs that must first be met. Indeed, physical activity may be a low priority for individuals seeking safety, reunification with loved ones, and food for their families, as a subsistence lifestyle makes excess weight gain, diabetes, and cardiovascular disease irrelevant. Yet, when working with people from a refugee background for whom these challenges all too frequently apply, opportunities for sport and activity have repeatedly surfaced as desirable and needed, yet are utterly deficient. If we conceptualize physical activity purely as a chronic disease prevention tool, its significance within under-resourced communities is most assuredly lost; however, if we harness the power of physical activity to serve as an agent of positive social change, then it instantly becomes more meaningful and necessary.