Low-frequency, high-density, inductively coupled plasma sources : operation and applications

Operation regimes, plasma parameters, and applications of the low-frequency (∼500 kHz) inductively coupled plasma (ICP) sources with a planar external coil are investigated. It is shown that highly uniform, high-density (ne∼9×1012 cm-3) plasmas can be produced in low-pressure argon discharges with moderate rf powers. The low-frequency ICP sources operate in either electrostatic (E) or electromagnetic (H) regimes in a wide pressure range without any Faraday shield or an external multipolar magnetic confinement, and exhibit high power transfer efficiency, and low circuit loss. In the H mode, the ICP features high level of uniformity over large processing areas and volumes, low electron temperatures, and plasma potentials. The low-density, highly uniform over the cross-section, plasmas with high electron temperatures and plasma and sheath potentials are characteristic to the electrostatic regime. Both operation regimes offer great potential for various plasma processing applications. As examples, the efficiency of the low-frequency ICP for steel nitriding and plasma-enhanced chemical vapor deposition of hydrogenated diamond-like carbon (DLC) films, is demonstrated. It appears possible to achieve very high nitriding rates and dramatically increase micro-hardness and wear resistance of the AISI 304 stainless steel. It is also shown that the deposition rates and mechanical properties of the DLC films can be efficiently controlled by selecting the discharge operating regime.

Endurance test-rig for diagnostics and prognostics of rolling element bearings

Detection of faults in roller element bearing is a topic widely discussed in the scientific field. Bearings diagnostics is usually performed by analyzing experimental signals, almost always vibration signals, measured during operation. A number of signal processing techniques have been proposed and applied to measured vibrations. The diagnostic effectiveness of the techniques depends on their capacities and on the environmental conditions (i.e. environmental noise). The current trend, especially from an industrial point of view, is to couple the prognostics to the diagnostics. The realization of a prognostic procedure require the definition of parameters able to describe the bearing condition during its operation. Monitoring the values of these parameters during time allows to define their trends depending on the progress of the wear. In this way, a relation between the variation of the selected parameters and the wear progress, useful for diagnostics and prognostics of bearings in real industrial applications, can be established. In this paper, a laboratory test-rig designed to perform endurance tests on roller element bearing is presented. Since the test-rig has operated for a short time, only some preliminary available results are discussed.

The French polisher and the unsentimental interior

In January 2011 a swollen Brisbane River broke its banks flooding riverside houses and buildings. The river’s water spread and rose up through storm water drains inundating some 20 000 houses in low-lying land. As the water receded those residents affected by the floods returned to their homes to assess the damage. While some people breathed a sigh of relief others were devastated by the overwhelming damage to their homes and personal belongings. Over the next few weeks the landscape of Brisbane was altered not merely by the mud and debris left by the torrent of water, but by the piles of domestic contents occupying Brisbane streets. Beds, toys, cabinets, plasterboard, tiles and household furniture lined curbsides waiting for collection. Later they would accumulate in public parks and sports centres to await disposal, momentarily creating an unsettling landscape of discarded domestic interiors. While most houses remained standing the heart breaking repercussions were evident in their interiority. Thousands of volunteers flocked to help those affected by the floods to purge the damage left by the water – removing wall and floor linings, discarding furniture and spoilt belongings. In her paper on Hurricane Katrina, Julieanna Preston wrote, ‘What anthropological evidence would we find as we followed their migration – heaps left by the side of the road, the physical weight overcoming the personal value…’ For many of the post flood restored homes and buildings entire interiors have been replaced, eradicating any trace of the significant event that disturbed them only months earlier. There were artifacts that would have survived the floods - furniture of solid timber – these were discarded and with them the patina that marked an important event in history. The patina is beyond technological reproducibility, and as Walter Benjamin writes, this being the whole premise of genuineness. It is the role of the French Polisher to maintain the true wear of the artefact for it is the patina that is most valuable in its ability to narrate the history of a piece. In 2012 two separate exhibitions in Brisbane will take place to display a selected collection of flood-damaged artefacts. This orchestrated way to commemorate the damage left by floods may be a method to compensate for the haste in which the damage was purged from the city. This need for exhibiting damaged artifacts illustrates Andreas Huyssen’s point that "…today memory is understood as a mode of re-presentation and as belonging to the present." This research looks at the dying trade of the French Polisher through conversations and a visual study of flood damaged furniture. The research also investigates the personal loss of artifacts through intimate stories shared by flood victims. This paper seeks to understand why so much was discarded and celebrate what remains.

The functional significance of fruit exocarp on host selection and oviposition by Queensland fruit fly, Bactrocera tryoni (Froggatt) (Tephritidae: Diptera)

Queensland fruit fly is Australia's most serious insect pest of horticulture. The fly lays its eggs into fruit, where they hatch into maggots which destroy the fruit. Understanding egg laying behaviour, known as oviposition, is a critical but under-researched aspect of fruit fly biology. This thesis focused on three aspects of oviposition: the role of fruit peel as a physical barrier to oviposition; the quality of fruit for maggot development; and the structure and wear of the egg laying organ – the ovipositor. Results showed that flies selected fruit based on their suitability for offspring survival, not because of the softness or hardness of fruit peel. Previously reported use of holes or wounds in fruit peel by ovipositing females was determined to be a mechanism which saved the female time, not a mechanism to reduce ovipositor wear. The results offer insights into the evolution of host use by fruit flies and their sustainable management.

1950s made in Brisbane : Italian tailors and the continental suit

During the 1950s and 1960s, when the French couturiers Dior, Balenciaga, Givenchy and Chanel dominated the fashion industry, the Italian community in Brisbane, Australia, was very active in the local industry through retail, dress-making and tailoring. Australia is geographically at the margins of the developed countries and has been dependent on European trends and taste. In the 1950s, communication was based on magazines and especially newsreels and film; each ethnic group dressed as they liked and according to their custom. Moreover, ‘Made in Italy’ was not yet the prestigious concept that revolutionized ready-to-wear design from the 1970s. However, Italian tailors and demi-couturiers brought to Brisbane their trans-national sense of elegance (the Italian style) and the taste in fashion that influenced new generations in England and elsewhere in Europe from the 1950s. They brought quality and workmanship, offering excellence through the use of quality fabrics from prestigious English and Italian brands. These tailors and dress-makers also contributed towards the local industry through passing on the skills that they brought from Italy. This article is based on a project that seeks to understand the connection between fashion, history and place. The area under examination is the Valley, short for Fortitude Valley, an area adjacent to the Brisbane CBD. Fundamental to this connection between place and fashion was the presence of many Italian migrants in the area. Through archival research and oral history, the aim of this ethnographic project is to bring to the fore an untold story about the economic and aesthetic contribution of Italian migrants to Queensland. Central to the understanding of this aesthetic change is the Italian suit. This research is innovative in that it opens a new area of study in Australian fashion history, connected to the history of migrants and their identity.

Why are we still fitting reusable soft contact lenses?

Whether the first daily disposable soft contact lens to enter the market in 1994 was the Premier lens (Award Technology, Scotland, UK; subsequently purchased by Bausch & Lomb, Rochester New York, USA) or the 1-Day Acuvue lens (Johnson and Johnson Vision Care, Jacksonville, Florida, USA) has long been a matter of bitter dispute1 but whatever the answer, this year marks the 20th anniversary of the launch of this modality of lens wear...

Influence of practice setting on contact lens prescribing in the United Kingdom

We sought to determine the impact of optometric practice setting on contact lens prescribing by analysing annual survey data of lens fits collected between 2009 and 2013 from independent and national group practices throughout the United Kingdom. Compared to national group practices, independent practices fit contact lenses to older patients and more females. Independent practices also undertake a lower proportion of soft lens fits overall (and thus a higher proportion of rigid lens fits), soft toric lens fits and daily disposable lens fits. There is a higher proportion of soft extended wear and multifocal lens fits in independent practices. We conclude that contact lens fitting behaviour is influenced by optometric practice setting.

Medical and nursing students perceived knowledge, attitudes, and practices concerning human immunodeficiency virus

Objective. To assess medical and nursing students’ knowledge, attitudes, and practices (KAP) regarding human immunodeficiency virus (HIV) in Fiji. Methods. A cross-sectional study of 275 medical and 252 nursing students that participated in a questionnaire survey on HIV KAP. Data was analysed according to their gender, program of study, and academic year. Results. The mean HIV knowledge (HK) and attitude scores were 16.0 and 41.3, respectively. Mean HK score was significantly higher in males compared to females. Significant positive correlations were found between HK and academic year for medical () and nursing () students and between HK and attitude scores (). The majority of students indicated fear in contracting HIV through clinical practice and felt that health care workers have the right to know a patients HIV status for their own safety. The majority would wear gloves to touch a patient if suspected of HIV. Conclusions. The study found a high level of HIV knowledge and positive attitude towards HIV patients. However, respondents also displayed negative attitudes and unacceptable practices probably due to fear. Training institutions need to ensure that students gain accurate knowledge on HIV especially on transmission routes to allay the fear of caring for HIV-infected patients.

Influences of luminance and accommodation stimuli on pupil size and pupil center location

PURPOSE. To investigate effects of luminance and accommodation stimuli on pupil size and pupil center location and their implications for progressive addition lens wear. METHODS. Participants were young and older adult groups (n=20, 22±2 years, age range 18-25 years; n=19, 49±4 years, 45-58 years). A wave aberrometer included a relay system to allow a 12.5°x11° background for the internal fixation target. Participants viewed the target under a matrix of conditions with luminance levels 0.01, 3.7, 120 and 6100 cd/m² and with accommodation stimuli up to 6 diopters in 2 diopter steps. Pupil sizes and their centers, relative to limbus centers, were determined from anterior eye images. RESULTS. With luminance increase, reduction in pupil size was accentuated by increase in accommodation stimulus in the young, but not in the older, group. As luminance increased, pupil center location altered. This was nasally in both groups with an average shift of approximately 0.12mm. Relative to the lowest stimulus condition, the mean of the maximum absolute pupil center shifts was 0.26±0.08mm for both groups with individual shifts up to 0.5mm, findings consistent with previous studies. There was no significant effect of accommodation on pupil center locations for either age group, or evidence that location was influenced by the combination of luminance and accommodation stimulus that resulted in any particular pupil size. CONCLUSIONS. Variations in luminance and accommodation influence pupil size, but only the former affects pupil center location significantly. Pupil center shifts are too small to be of concern in fitting progressive addition lenses.

Trashtopia by Maison Briz Vegas

Description of the Work Trashtopia was a fashion exhibition at Craft Queensland’s Artisan gallery showcasing outfits made entirely from rubbish materials. The exhibition was part of an on-going series by the Queensland Fashion Archives, called Remember or Revive. Maison Briz Vegas designers, Carla Binotto and Carla van Lunn created a dystopian beach holiday tableau referencing mid-century Californian and Gold Coast beach culture and style, and today’s plastic pollution of the world’s oceans. The display engaged a popular audience with ideas about environmental destruction and climate change while bringing twentieth and twenty-first century consumer and leisure culture into question. The medium of fashion was used as a means of amusement and provocation. The fashion objects and installation questioned current mores about the material value of rubbish and the installation was also a work of environmental activism. Statement of the Research Component The work was framed by critical reflections of contemporary consumer culture and research fields questioning value in waste materials and fashion objects. The work is situated in the context of conceptual and experimental fashion design practice and fashion presentation. The exhibited work transgressed the conventional production methods and material choice of designer fashion garments, for example, discarded plastic shopping bags were painstakingly shredded to mimic ostrich feathers. The viewer was prompted to reflect on the materiality of rubbish and its potential for transformation. The exhibition also sits in the context of culture jamming and contemporary activist practice. The work references and subverts twentieth century beach holiday culture, contrasting resort wear with a contemporary picture of plastic pollution of the oceans and climate change. Hawaiian style prints contained a playful and dark narrative of dying marine-life and the viewer was invited to take a “Greetings from Trashtopia” postcard depicting fashion models floating in oceans of plastic rubbish. This reflective creative practice sought to address the question of whether fashion made from recycled rubbish materials can critically and emotionally engage viewers with questions about contemporary consumer culture and material value. This work presents an innovative model of fashion design practice in which rubbish materials are transformed into designer garments and rubbish is placed centre stage in the public presentation of the designs. In overturning the traditional model of fashion presentation, the viewer is also given a deeper connection to the recycling process and complex ideas of waste and value. In 2015 two outfits from the exhibition were selected, along with works from three leading Australian fashion labels, and four leading New Zealand labels, for a commemorative ANZAC fashion collection shown at iD Dunedin Fashion Week. The show titled, “Together Alone, revisited” reprised an Australian and New Zealand fashion exhibition first held at the National Gallery of Victoria in 2009.

Source characterisation of urban road surface pollutants for enhanced water quality predictions

This study developed a comprehensive research methodology for identification and quantification of sources responsible for pollutant build-up and wash-off from urban road surfaces. The study identified soil and asphalt wear, and non-combusted diesel fuel as the most influential sources for metal and hydrocarbon pollution respectively. The study also developed mathematical models to relate contributions from identified sources to underlying site specific factors such as land use and traffic. Developed mathematical model will play a key role in urban planning practices, enabling the implementation of effective water pollution control strategies.

Inside the ‘Hurt Locker’: The combined effects of explosive ordnance disposal and chemical protective clothing on physiological tolerance time in extreme environments

Background Explosive ordnance disposal (EOD) technicians are often required to wear specialised clothing combinations that not only protect against the risk of explosion but also potential chemical contamination. This heavy (>35kg) and encapsulating ensemble is likely to increase physiological strain by increasing metabolic heat production and impairing heat dissipation. This study investigated the physiological tolerance times of two different chemical protective undergarments, commonly worn with EOD personal protective clothing, in a range of simulated environmental extremes and work intensities Methods Seven males performed eighteen trials wearing two ensembles. The trials involved walking on a treadmill at 2.5, 4 and 5.5 km.h-1 at each of the following environmental conditions, 21, 30 and 37°C wet bulb globe temperature (WBGT). The trials were ceased if the participants’ core temperature reached 39°C, if heart rate exceeded 90% of maximum, if walking time reached 60 minutes or due to volitional fatigue. Results Physiological tolerance times ranged from 8 to 60 min and the duration (mean difference: 2.78 min, P>0.05) were similar in both ensembles. A significant effect for environment (21>30>37°C WBGT, P<0.05) and work intensity (2.5>4>5.5 km.h-1, P< 0.05) was observed in tolerance time. The majority of trials across both ensembles (101/126; 80.1%) were terminated due to participants achieving a heart rate equivalent to greater than 90% of their maximum. Conclusions Physiological tolerance times wearing these two chemical protective undergarments, worn underneath EOD personal protective clothing, were similar and predominantly limited by cardiovascular strain.

Transcutaneous bone-anchoring prosthesis with knee replacement: A novel treatment for amputees

Over the last two decades, Transcutaneous Bone-Anchored Prosthesis (TCBAP) has proven to be an effective alternative for prosthetic attachment for amputees, particularly for individuals unable to wear a socket. However, the load transmitted through a typical TCBAP to the residual tibia and knee joint can be unbearable for transtibial amputees with knee arthritis. The aims of this study are (A) to describe the surgical procedure combining TKR with TCBAP for the first time; and (B) to present preliminary data on potential risks and benefits with assessment of clinical and functional outcomes at follow up.

An examination of the factors contributing to unlicensed driving. Report to Queensland Department of Transport and Main Roads

Unlicensed driving is a serious problem in many countries, despite ongoing improvements in traffic law enforcement practices and technology. Unlike alcohol impairment and speeding, unlicensed driving does not play a direct causative role in road crashes. However it represents a major problem for road safety in two respects. Firstly, it undermines the effectiveness of driver licensing systems by preventing the allocation of demerit points and reducing the impact of licence loss (Watson, 2004b). Secondly, there is a growing body of evidence linking unlicensed driving to a cluster of high-risk behaviours including drink driving, speeding, failure to wear seat belts and motorcycle use (Griffin & DeLaZerda, 2000; Harrison, 1997; Watson, 1997, 2004b). Consistent with this, utilising the quasi-induced exposure method, Watson (2004a) estimated that in Queensland, unlicensed drivers were almost three times more likely to be involved in a reported crash than licensed drivers.