Ironless wheel motor for a direct drive vehicle application

An ironless motor for use as direct wheel drive is presented. The motor is intended for use in a lightweight (600kg), low drag, series hybrid commuter vehicle under development at The University of Queensland. The vehicle will utilise these ironless motors in each of its rear wheels, with each motor producing a peak torque output of 500Nm and a maximum rotational speed of 1500rpm. The axial flux motor consists of twin Ironless litz wire stators with a central magnetic ring and simplified Halbach magnet arrays on either side. A small amount of iron is used to support the outer Halbach arrays and to improve the peak magnetic flux density. Ducted air cooling is used to remove heat from the motor and will allow for a continuous torque rating of 250Nm. Ironless machines have previously been shown to be effective in high speed, high frequency applications (+1000Hz). They are generally regarded as non-optimal for low speed applications as iron cores allow for better magnet utilisation and do not significantly increase the weight of a machine. However, ironless machines can also be seen to be effective in applications where the average torque requirement is much lower than the peak torque requirement such as in some vehicle drive applications. The low spinning losses in ironless machines are shown to result in very high energy throughput efficiency in a wide range of vehicle driving cycles.

Why are pedestrian crashes so different in developing countries? A review of relevant factors in relation to their impact in Ethiopia

Much is known about pedestrian behaviour and crash risk in developed countries. In contrast, the literature on pedestrian crash risk in developing countries reveals wide gaps in knowledge and understanding, and a comprehensive assessment is lacking. In particular, pedestrian behaviour in developing countries is fundamentally different in comparison to developed countries, and is influenced by a variety of less well understood contributing factors, leading to difficulty in modelling and predicting pedestrian crash risk and in turn identifying effective safety countermeasures. This paper provides a comprehensive synthesis of the factors known to influence pedestrian crash risk in developing countries, then focuses on Ethiopia as a specific example. The paper identifies where critical gaps in knowledge exist regarding pedestrian crash risk and associated behaviour in developing countries--a set of knowledge gaps which collectively are significant. The paper concludes by articulating a critical research path moving forward, with the aim to achieve an improved understanding of developing country pedestrian crash risk, and an ultimate goal of identifying effective pedestrian safety countermeasures suited to the unique challenges faced by transport system managers in developing countries.

Characteristics of police-reported road traffic crashes in Ethiopia over a six year period

Ethiopia has one of Africa’s fastest growing non-oil producing economies and an increasing level of motorisation (AfDB, OECD, UNDP, & UNECA, 2012). This rapidly increasing mobility has created some unique road safety concerns; however there is scant published information and related commentary (United Nations Economic Commission for Africa, 2009). The objective of this paper is to quantify police-reported traffic crashes in Ethiopia and characterise the existing state of road safety. Six years (July 2005 - June 2011) of police-reported crash data were analysed, consisting of 12,140 fatal and 29,454 injury crashes on the country’s road network. The 12,140 fatal crashes involved 1,070 drivers, 5,702 passengers, and 7,770 pedestrians, totalling 14,542 fatalities, an average of 1.2 road user fatalities per crash. An important and glaring trend that emerges is that more than half of the fatalities in Ethiopia involve pedestrians. The majority of the crashes occur during daytime hours, involve males, and involve persons in the 18-50 age group—Ethiopia’s active workforce. Crashes frequently occur in mid blocks or roadways. The predominant collision between motor vehicles and pedestrians was a rollover on a road tangent section. Failing to observe the priority of pedestrians and speeding were the major causes of crashes attributed by police. Trucks and minibus taxis were involved in the majority of crashes, while automobiles (small vehicles) were less involved in crashes relative to other vehicle types, partially because small vehicles tend to be driven fewer kilometres per annum. These data illustrate and justify a high priority to identify and implement effective programs, policies, and countermeasures focused on reducing pedestrian crashes.

How Can Models of Motor Control Be Useful for Understanding Low Back Pain?

Introduction. The purpose of this chapter is to address the question raised in the chapter title. Specifically, how can models of motor control help us understand low back pain (LBP)? There are several classes of models that have been used in the past for studying spinal loading, stability, and risk of injury (see Reeves and Cholewicki (2003) for a review of past modeling approaches), but for the purpose of this chapter we will focus primarily on models used to assess motor control and its effect on spine behavior. This chapter consists of 4 sections. The first section discusses why a shift in modeling approaches is needed to study motor control issues. We will argue that the current approach for studying the spine system is limited and not well-suited for assessing motor control issues related to spine function and dysfunction. The second section will explore how models can be used to gain insight into how the central nervous system (CNS) controls the spine. This segues segue nicely into the next section that will address how models of motor control can be used in the diagnosis and treatment of LBP. Finally, the last section will deal with the issue of model verification and validity. This issue is important since modelling accuracy is critical for obtaining useful insight into the behavior of the system being studied. This chapter is not intended to be a critical review of the literature, but instead intended to capture some of the discussion raised during the 2009 Spinal Control Symposium, with some elaboration on certain issues. Readers interested in more details are referred to the cited publications.

Determinants of drink-driving and association between drink-driving and road traffic fatalities in Ghana

Background Drink-driving has been implicated in many road traffic crashes in the world. Consequently, the developed countries have prioritized drink-driving research. Contrary, drink-driving research has not attained any meaningful consideration in many developing countries. It is therefore imperative to intensify drink-driving research so as to provide research driven solutions to the menace. Aims The objective is to establish determinants of drink-driving and its association with traffic crashes in Ghana. Methods A randomized roadside breathalyzer survey was conducted. A multivariable logistic regression was used to establish significant determinants of drink-driving and a bivariate logistic regression to establish the association between drink–driving and road traffic crashes in Ghana. Results In total, 2,736 motorists were randomly stopped for breath testing of whom 8.7% tested positive for alcohol. Among the total participants, 5.5% exceeded the legal BAC limit of 0.08%. Formal education is associated with a reduced likelihood of drink-driving compared with drivers without formal education. The propensity to drink-drive is 1.8 times higher among illiterate drivers compared with drivers with basic education. Young adult drivers also recorded elevated likelihoods for driving under alcohol impairment compared with adult drivers. The odds of drink-driving among truck drivers is OR=1.81, (95% CI=1.16 to 2.82) and two wheeler riders is OR=1.41, (95% CI=0.47 to 4.28) compared with car drivers. Contrary to general perception, commercial car drivers have a significant reduced likelihood of 41%, OR=0.59, (95% CI=0.38 to 0.92) compared with the private car driver. Bivariate analysis conducted showed a significant association between the proportion of drivers exceeding the legal BAC limit and road traffic fatalities, p<0.001. The model predicts a 1% increase in the proportion of drivers exceeding the legal BAC to be associated with a 4% increase in road traffic fatalities, 95% CI= 3% to 5% and vice versa. Discussion and conclusion A positive and significant association between roadside alcohol prevalence and road traffic fatality has been established. Scaling up roadside breath test, determining standard drink and disseminating to the populace and formulating policies targeting the youth such as increasing minimum legal drinking age and reduced legal BAC limit for the youth and novice drivers might improve drink-driving related crashes in Ghana.

Effectiveness of pilot car operations in reducing speeds in a long-term rural highway work zone

Pilot cars are used in one-lane two-way work zones to guide traffic and keep their speeds within posted limits. While many studies have examined the effectiveness of measures to reduce vehicle speeds in work zones, little is known about the reductions achievable through the use of pilot cars. This paper examines the effectiveness of a pilot car in reducing travel speeds in a rural highway work zone in Queensland, Australia. Analysis of speed data covering a period of five days showed that a pilot car reduced average speeds at the treatment location, but not downstream. The proportion of vehicles speeding through the activity area was also reduced, particularly those traveling at 10 km/h or more above the posted limit. Motorists were more likely to speed during the day, under a 40 kh/h limit, when traffic volumes were higher and when there were fewer vehicles in the traffic stream. Medium vehicles were less likely to speed in the presence of a pilot car than light vehicles. To maximize these benefits, it is necessary to ensure that the pilot car itself is not speeding.

Behavioural Inhibition System response to conflicting advertisement cues: Road safety messages vs. motor vehicle promotional advertisements

This study assessed the revised Behavioural Inhibition System (BIS), as conceptualised by Gray and McNaughton’s (2000) revised RST, by exposing participants to a loss-framed road safety message (emphasising the negative consequences of speeding behaviour) and a high performance motor vehicle promotional advertisement. Licensed young drivers (N = 40, aged 17–25 years) were randomly allocated to view either the message or both the message and advertisement. Participants then completed a computerised lexical decision task prior to completing three personality measures: Corr-Cooper RST-PQ, CARROT and Q-Task. It was predicted that those with a stronger BIS would demonstrate greater processing of these mixed message cues compared to weaker BIS individuals, and that this BIS effect would only be observed in the mixed cues condition (due to simultaneous activation of the incentive and punishment systems). Preliminary findings will be discussed in the context of the influence of personality traits on health message processing.

Competition Hertz : the culture and practice of car audio competitions

The present paper explores extreme car audio systems and the culture and practices that surround car audio competitions. I begin by examining whether, and how, car audio can be thought of as a 'music scene' and in what ways the culture and practice of car audio may fit within post-subcultural discourses. Following this, I offer a description of car audio competitions, revealing some of the practices that define this aspect of car audio scenes. In particular, I concentrate on sound pressure level (SPL) competitions and some of the interesting aspects of the SPL scene. Finally, I briefly examine how the powerful effects (and affects) of bass frequencies are an important part of the attraction of loud car audio systems and how car audio systems contribute to the territorializing of urban spaces.

Development of polymers for Non-CAR resists for EUV lithography

Three strategies for approaching the design and synthesis of non-chemically amplified resists (non-CARs) are presented. These are linear polycarbonates, star polyester-blk-poly(methyl methacrylate) and comb polymers with polysulfone backbones. The linear polycarbonates were designed to cleave when irradiated with 92 eV photons and high Tg alicyclic groups were incorporated into the backbone to increase Tg and etch resistance. The star block copolymers were designed to have a core that is sensitive to 92 eV photons and arms that have the potential to provide properties such as high Tg and etch resistance. Similarly the polysulfone comb polymers were designed to have an easily degradable polymer backbone and comb-arms that impart favorable physical properties. Initial patterning results are presented for a number of the systems.

Motor controller simulation and embedded implementation for a blood pump

This study was a step forward in modeling, simulation and microcontroller implementation of a high performance control algorithm for the motor of a blood pump. The rotor angle is sensed using three Hall effect sensors and an algorithm is developed to obtain better angular resolution from the three signals for better discrete-time updates of the controller. The performance of the system was evaluated in terms of actual and reference speeds, stator currents and power consumption over a range of reference speeds up to 4000 revolutions per minute. The use of fewer low cost Hall effect sensors compared to expensive high resolution sensors could reduce the cost of blood pumps for total artificial hearts.

Active control of car suspension systems using IDA-PBC

This paper considers the design of active control for car suspension systems using a particular form of energy-based control called Interconnection-and-Damping-Assignment Passivity-Based Control (IDA-PBC). This approach allows one to shape the kinetic and potential energy as well as modify the power flow among different components of the system by changing the interconnection and dissipative structure in a meaningful way. Different controller parameterisations are considered to design a class of controllers for active suspension systems.

Sensor fault-resilient control of interior permanent-magnet synchronous motor drives

In a conventional ac motor drive using field-oriented control, a dc-link voltage, speed, and at least two current sensors are required. Hence, in the event of sensor failure, the performance of the drive system can be severely compromised. This paper presents a sensor fault-tolerant control strategy for interior permanent-magnet synchronous motor (IPMSM) drives. Three independent observers are proposed to estimate the speed, dc-link voltage, and currents of the machine. If a sensor fault is detected, the drive system isolates the faulty sensor while retaining the remaining functional ones. The signal is then acquired from the corresponding observer in order to maintain the operation of the drive system. The experimental results provided verify the effectiveness of the proposed approach.

A sensor fault detection and isolation method in interior permanent-magnet synchronous motor drives based on an extended Kalman filter

Interior permanent-magnet synchronous motors (IPMSMs) become attractive candidates in modern hybrid electric vehicles and industrial applications. Usually, to obtain good control performance, the electric drives of this kind of motor require one position, one dc link, and at least two current sensors. Failure of any of these sensors might lead to degraded system performance or even instability. As such, sensor fault resilient control becomes a very important issue in modern drive systems. This paper proposes a novel sensor fault detection and isolation algorithm based on an extended Kalman filter. It is robust to system random noise and efficient in real-time implementation. Moreover, the proposed algorithm is compact and can detect and isolate all the sensor faults for IPMSM drives. Thorough theoretical analysis is provided, and the effectiveness of the proposed approach is proven by extensive experimental results.