Evaluation of a hybrid scaffold/cell construct in repair of high-load-bearing osteochondral defects in rabbits

The objective of this study was to evaluate the feasibility and potential of a hybrid scaffold system in large- and high-load-bearing osteochondral defects repair. The implants were made of medical-grade PCL (mPCL) for the bone compartment whereas fibrin glue was used for the cartilage part. Both matrices were seeded with allogenic bone marrow-derived mesenchymal cells (BMSC) and implanted in the defect (4 mm diameter×5 mm depth) on medial femoral condyle of adult New Zealand White rabbits. Empty scaffolds were used at the control side. Cell survival was tracked via fluorescent labeling. The regeneration process was evaluated by several techniques at 3 and 6 months post-implantation. Mature trabecular bone regularly formed in the mPCL scaffold at both 3 and 6 months post-operation. Micro-Computed Tomography showed progression of mineralization from the host–tissue interface towards the inner region of the grafts. At 3 months time point, the specimens showed good cartilage repair. In contrast, the majority of 6 months specimens revealed poor remodeling and fissured integration with host cartilage while other samples could maintain good cartilage appearance. In vivo viability of the transplanted cells was demonstrated for the duration of 5 weeks. The results demonstrated that mPCL scaffold is a potential matrix for osteochondral bone regeneration and that fibrin glue does not inherit the physical properties to allow for cartilage regeneration in a large and high-load-bearing defect site. Keywords: Osteochondral tissue engineering; Scaffold; Bone marrow-derived precursor cells; Fibrin glue

Lateral shearing interferometry, dynamic wavefront sensing, and high-speed videokeratoscopy for noninvasive assessment of tear film surface characteristics : a comparitive study

There are several noninvasive techniques for assessing the kinetics of tear film, but no comparative studies have been conducted to evaluate their efficacies. Our aim is to test and compare techniques based on high-speed videokeratoscopy (HSV), dynamic wavefront sensing (DWS), and lateral shearing interferometry (LSI). Algorithms are developed to estimate the tear film build-up time TBLD, and the average tear film surface quality in the stable phase of the interblink interval TFSQAv. Moderate but significant correlations are found between TBLD measured with LSI and DWS based on vertical coma (Pearson's r2=0.34, p<0.01) and higher order rms (r2=0.31, p<0.01), as well as between TFSQAv measured with LSI and HSV (r2=0.35, p<0.01), and between LSI and DWS based on the rms fit error (r2=0.40, p<0.01). No significant correlation is found between HSV and DWS. All three techniques estimate tear film build-up time to be below 2.5 sec, and they achieve a remarkably close median value of 0.7 sec. HSV appears to be the most precise method for measuring tear film surface quality. LSI appears to be the most sensitive method for analyzing tear film build-up.

'I am smart and I am not joking': Aiming high in the middle years of schooling

In this paper, we draw on accounts from students to inform a Middle Schooling movement that has been variously described as "arrested", "unfinished" and "exhausted". We propose that if the Middle Schooling movement is to understand the changing worlds of students and develop new approaches in the middle years of schooling, then it is important to draw on the insights that individual students can provide by conducting research with "students-as-informants". The early adolescent informants to this paper report high hopes for their futures (despite their lower socio-economic surroundings), which reinforces the importance of supporting successful learner identities and highlights the role of schooling in the decline of adolescent student aspirations. However, their insights did not stop at the individual learner, with students also identifying cultural and structural constraints to reform. As such, we argue that students may be both an important resource for inquiry into individual school reform and for the Middle Schooling movement internationally.

Wavelet based approaches and high resolution methods for complex process models

Many industrial processes and systems can be modelled mathematically by a set of Partial Differential Equations (PDEs). Finding a solution to such a PDF model is essential for system design, simulation, and process control purpose. However, major difficulties appear when solving PDEs with singularity. Traditional numerical methods, such as finite difference, finite element, and polynomial based orthogonal collocation, not only have limitations to fully capture the process dynamics but also demand enormous computation power due to the large number of elements or mesh points for accommodation of sharp variations. To tackle this challenging problem, wavelet based approaches and high resolution methods have been recently developed with successful applications to a fixedbed adsorption column model. Our investigation has shown that recent advances in wavelet based approaches and high resolution methods have the potential to be adopted for solving more complicated dynamic system models. This chapter will highlight the successful applications of these new methods in solving complex models of simulated-moving-bed (SMB) chromatographic processes. A SMB process is a distributed parameter system and can be mathematically described by a set of partial/ordinary differential equations and algebraic equations. These equations are highly coupled; experience wave propagations with steep front, and require significant numerical effort to solve. To demonstrate the numerical computing power of the wavelet based approaches and high resolution methods, a single column chromatographic process modelled by a Transport-Dispersive-Equilibrium linear model is investigated first. Numerical solutions from the upwind-1 finite difference, wavelet-collocation, and high resolution methods are evaluated by quantitative comparisons with the analytical solution for a range of Peclet numbers. After that, the advantages of the wavelet based approaches and high resolution methods are further demonstrated through applications to a dynamic SMB model for an enantiomers separation process. This research has revealed that for a PDE system with a low Peclet number, all existing numerical methods work well, but the upwind finite difference method consumes the most time for the same degree of accuracy of the numerical solution. The high resolution method provides an accurate numerical solution for a PDE system with a medium Peclet number. The wavelet collocation method is capable of catching up steep changes in the solution, and thus can be used for solving PDE models with high singularity. For the complex SMB system models under consideration, both the wavelet based approaches and high resolution methods are good candidates in terms of computation demand and prediction accuracy on the steep front. The high resolution methods have shown better stability in achieving steady state in the specific case studied in this Chapter.

Critical analysis of high particle number emissions from accelerating compressed natural gas buses

Compressed natural gas (CNG) engines are thought to be less harmful to the environment than conventional diesel engines, especially in terms of particle emissions. Although, this is true with respect to particulate matter (PM) emissions, results of particle number (PN) emission comparisons have been inconclusive. In this study, results of on-road and dynamometer studies of buses were used to derive several important conclusions. We show that, although PN emissions from CNG buses are significantly lower than from diesel buses at low engine power, they become comparable at high power. For diesel buses, PN emissions are not significantly different between acceleration and operation at steady maximum power. However, the corresponding PN emissions from CNG buses when accelerating are an order of magnitude greater than when operating at steady maximum power. During acceleration under heavy load, PN emissions from CNG buses are an order of magnitude higher than from diesel buses. The particles emitted from CNG buses are too small to contribute to PM10 emissions or contribute to a reduction of visibility, and may consist of semivolatile nanoparticles.

Strengthening of circular hollow steel tubular sections using high modulus CFRP sheets

This paper describes the behaviour of very high strength (VHS) circular steel tubes strengthened by carbon fibre reinforced polymer (CFRP) and subjected to axial tension. A series of tests were conducted with different bond lengths and number of layers. The distribution of strain through the thickness of CFRP layers and along CFRP bond length was studied. The strain was found to generally decrease along the CFRP bond length far from the joint. The strain through the thickness of the CFRP layers was also found to decrease from bottom to top layer. The effective bond length for high modulus CFRP was established. Finally empirical models were developed to estimate the maximum load for a given CFRP arrangement.

Accountability through high-stakes testing and curriculum change

The motivation for secondary school principals in Queensland, Australia, to investigate curriculum change coincided with the commencement in 2005 of the state government’s publication of school exit test results as a measure of accountability. Aligning the schools’ curriculum with the requirements of high-stakes testing is considered by many academics and teachers as negative outcome of accountability for reasons such as ‘teaching to the test’ and narrowing the curriculum. However, this article outlines empirical evidence that principals are instigating curriculum change to improve published high-stakes test results. Three principals in this study offered several reasons as to why they wished to implement changes to school curricula. One reason articulated by all three was the pressures of accountability, particularly through the publication of high-stakes test data which has now become commonplace in education systems of many Western Nations.

Use of lifts and refuge floors for fire evacuation in high rise apartment buildings

If current population and accommodation trends continue, Australian cities will, in the future, have noticeable numbers of apartment buildings over 60 storeys high. With an aging population it follows that a significant proportion of those occupying these buildings will be senior citizens, many of whom will have some form of disability. For these occupants a fire emergency in a high rise building presents a serious problem. Currently lifts cannot be used for evacuation and going down 60 storeys in a fire isolated staircase would be physically impossible for many. Therefore, for many, the temptation to remain in one’s unit will be very strong. With an awareness of this behaviour trend in older residents, many researchers have, in recent years, explored the possible wider use of lifts in a fire emergency. So far the use of lifts for evacuation has been approved for a small number of buildings but wide acceptance of this solution is still to be achieved. This paper concludes that even in high-rise apartment buildings where lifts are approved for evacuation, architects should design the building with alternative evacuation routes and provide suitable safe refuge areas for those who cannot use the stairs when the lifts are unavailable.

The role of bricolage and resource constraints in high potential sustainability ventures

Sustainability decisions and their impacts may be among the greatest challenges facing the world in the 21st century (Davos 2000). Apart from adaptation on the part of established organizations these challenges are arguably going to require solutions developed by new actors However, young ventures have only recently begun generating research interest within sustainability literature (Shepherd et al. 2009). In particular, little is known about resource behaviours of these ventures and how they adapt to substantial resource constraints. One promising theory that has been identified as a way that some entrepreneurs manage constraints is bricolage: a construct defined as “making do by applying combinations of the resources at hand to new problems and opportunities” (Baker and Nelson 2005: 333). Bricolage may be critical as the means of continued venture success as these ventures are frequently developed in severe resource constraint, owing to higher levels of technical sophistication (Rothaermel and Deeds 2006). Further, they are often developed by entrepreneurs committed to personal and social goals of resourcefulness, including values that focus on conservation rather than consumption of resources (Shepherd et al. 2009). In this paper, using seven novel cases of high potential sustainability firms from CAUSEE we consider how constraints impact resource behaviours and further illustrate and extend bricolage domains previously developed by Baker and Nelson (2005) with recommendations for theory and practice provided.

Grade A Taipei junior high school principals’ self-reported leadership practices

The principal’s leadership and curriculum development are considered the core elements for creating a high performing junior high school. In Taiwan, mathematics curriculum reform has been an ongoing topic since 1994. The pedagogy, classroom interactions, and the underlying philosophy of mathematics education have varied with different versions of guidelines. These changes inevitably increase the requirement for principals’ leadership in order to effectively implement the curriculum reform. Principals’ leadership is essential to the success of the implementation in their school. This study aimed to explore and identify the leadership of junior high school principals whose schools had been judged by the Taipei City Government as Grade A junior high schools. Principals’ implementations of the reformed mathematics curriculum were used as examples to generate insights of their leadership. This study drew upon a multiple-case study approach. Data were collected from interviews, observations, and documentations. Bass and Avolio’s (1997) full range leadership theory provided a structure for gaining insight into these principals’ leadership practices. Five Grade A Taipei junior high school principals participated and shared their leadership concepts and experiences. Findings revealed that the leadership preferences of the five principles varied considerably. Management by exception-active, contingent reward, individualised consideration, and idealised influence were Grade A Taipei junior high school principals’ preferred leadership practices. In addition, principals’ leadership strategies associated with these practices were identified. These principals had adopted a range of leadership strategies according to the staff and school needs. Results of this study have implications for both Taiwanese principals and education departments. Principals can enhance their leadership by gaining more understanding about the Grade A principals’ leadership practices and strategies. Taiwanese education departments can improve school leadership training programs by focusing on these practices and strategies, which may also lead to more effective strategies for implementing national curriculum reform.

Accurate urban road model reconstruction from high resolution remotely sensed imagery based on Support Vector Machine and Gabor filters

In this paper, we presented an automatic system for precise urban road model reconstruction based on aerial images with high spatial resolution. The proposed approach consists of two steps: i) road surface detection and ii) road pavement marking extraction. In the first step, support vector machine (SVM) was utilized to classify the images into two categories: road and non-road. In the second step, road lane markings are further extracted on the generated road surface based on 2D Gabor filters. The experiments using several pan-sharpened aerial images of Brisbane, Queensland have validated the proposed method.

Handhelds nuture inquiring minds : an Australian high school case study

Technology is not always introduced into educational contexts in ways that position pedagogy to the fore. In optimizing learning, forward looking approaches require that we question what it means to be an educated person in the 21st Century and how individuals should engage with technologies to be suitably equipped for emergent knowledge age work. Responses to such ideas typically emphasize collaborative knowledge building where technology is employed as a tool to think with and allows for the active messing with and the development of ideas, rather than merely being a passive window to information. This paper discusses a very deliberate attempt to address a range of imperatives and competing demands within a high school setting where wireless handheld technologies integrated with a learning management system (Moodle) are used to scaffold and implement knowledge sharing and knowledge-building within the school community.

High-stakes national testing: it's global, it's here to stay, and graduating teachers need to know about it

My oldest daughter recently secured a position as a Science/Geography teacher in a P-12 Catholic College in regional Queensland. This paper looks at the teaching world into which she has graduated. Specifically, the paper will outline and discuss findings from a survey of graduating early childhood student teachers in relation to their knowledge and skills of the current regime of high-stakes testing in Australia. The paper argues that understanding accountability and possessing skills to scrutinise test data are essential for the new teacher as s/he enters a profession in which governments world-wide are demanding a return for their investment in education. The paper will examine literature on accountability and surveillance in the form of high-stakes testing from global, school and classroom perspectives. It makes the claim that it is imperative for beginning teachers to be able to interpret high-stakes test data and considers the skills required to do this. The paper also draws on local research to comment on the readiness of graduates to meet this comparatively new professional demand.

High bandwidth voltage and current control design for voltage source converters

In this paper, two different high bandwidth converter control strategies are discussed. One of the strategies is for voltage control and the other is for current control. The converter, in each of the cases, is equipped with an output passive filter. For the voltage controller, the converter is equipped with an LC filter, while an output has an LCL filter for current controller. The important aspect that has been discussed the paper is to avoid computation of unnecessary references using high-pass filters in the feedback loop. The stability of the overall system, including the high-pass filters, has been analyzed. The choice of filter parameters is crucial for achieving desirable system performance. In this paper, the bandwidth of achievable performance is presented through frequency (Bode) plot of the system gains. It has been illustrated that the proposed controllers are capable of tracking fundamental frequency components along with low-order harmonic components. Extensive simulation results are presented to validate the control concepts presented in the paper.

The role of emotional labour and role stress on burnout and psychological strain in high contact service employees

This study examines the relationships between job demands (in the form of role stressors and emotional management) and employee burnout amongst high contact service employees. Employees in customer facing roles are frequently required to manage overwhelming, conflicting or ambiguous demands, which they may feel ill-equipped to handle. Simultaneously, they must manage the emotions they display towards customers, suppressing some, and expressing others, be they genuine or contrived. If the in-role effort required of employees exceeds their inherent capacity to cope, burnout may result. Burnout, in turn, can have serious detrimental consequences for the psychological well being of employees. We find that both emotional management and role stressors impact burnout. We also confirm that burnout predicts psychological strain. In line with the Job Demands and Resources Model, we examine the mitigating impact of perceived support on these relationships but do not find a significant mitigating impact.